The document provides instructions for removing and installing a unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting tubes, hoses and harnesses from the pump before removing mounting bolts and the pump. For installation, the instructions specify applying a new O-ring seal and mounting the pump using the bolts, then reconnecting all tubes, hoses and harnesses. Special procedures are provided for pumps with dual tapered roller bearings.
Caterpillar Cat 336D2 L Excavator (Prefix ELR) Service Repair Manual (ELR0000...cnp692569
This document provides instructions for removing and installing the unit injector hydraulic pump on Caterpillar C9 engines. The removal process involves disconnecting fuel lines and electrical connections, removing mounting bolts, and taking out the O-ring seal. Installation is the reverse of removal, and includes cleaning parts, applying a new O-ring seal, reconnecting lines and bolts, and filling fluids to the proper levels. Procedures are provided for pumps with both non-dual and dual tapered roller bearings.
The document provides instructions for removing and installing the unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting fuel lines and electrical connections, removing mounting bolts, and taking out the pump. The installation procedure specifies cleaning parts, applying a new O-ring seal, positioning the pump, and securing it with bolts. Proper containment of fluids is emphasized during maintenance.
Caterpillar Cat 336D2 L Excavator (Prefix ELR) Service Repair Manual (ELR0000...zatao0179249295
The document provides instructions for removing and installing the unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting fuel lines and electrical connections, removing mounting bolts, and taking out the pump. The installation procedure specifies cleaning parts, applying a new O-ring seal, positioning the pump, and securing it with bolts. Proper containment of fluids is emphasized during maintenance.
This document provides instructions for removing and installing the unit injector hydraulic pump on Caterpillar C9 engines. The removal process involves disconnecting fuel lines and electrical connections, removing mounting bolts, and taking out the O-ring seal. Installation is the reverse, applying a new O-ring seal and grease, positioning the pump, and reconnecting all lines and bolts. Proper cleaning and containment of fluids is emphasized to prevent contamination.
Caterpillar Cat 336D2 L Excavator (Prefix ELR) Service Repair Manual (ELR0000...kesi7153062
This document provides instructions for removing and installing the unit injector hydraulic pump on Caterpillar C9 engines. The removal process involves disconnecting fuel lines and electrical connections, removing mounting bolts, and taking out the pump. Installation is the reverse, applying a new O-ring seal and reconnecting all lines. Proper cleaning and containment of fluids is emphasized. The document outlines procedures for both non-dual and dual tapered roller bearing pump types.
This document provides instructions for removing and installing the unit injector hydraulic pump on Caterpillar C9 engines. The removal process involves disconnecting fuel lines and electrical connections, removing mounting bolts, and taking out the pump. Installation is the reverse, applying a new O-ring seal and reconnecting all lines. Proper cleaning and containment of fluids is emphasized. Both non-dual and dual tapered roller bearing pump types are covered.
1. The document provides instructions for removing and installing the flywheel and crankshaft rear seal on a C7.1 engine that powers a 323 excavator.
2. To remove the flywheel, bolts must first be removed and guide studs installed before lifting the flywheel off using a lifting device. The ring gear can then be removed by heating and pressing it off.
3. Flywheel installation requires cleaning and inspecting components, heating and pressing the ring gear if replaced, and torquing bolts with the flywheel secured to prevent rotation.
4. Crankshaft rear seal removal requires removing screws using a Torx socket after removing the flywheel housing. The sealed assembly
Caterpillar Cat 326D2 (Prefix KGY) Service Repair Manual (KGY00001 and up).pdfkm7seydwuhdw
This document provides instructions for disassembling and assembling the travel motor of a 326D2 excavator. It lists the required tools and gives step-by-step procedures to remove and install various components of the travel motor such as the head, bearings, brake piston, seals, and housing covers. Special care must be taken when handling springs or installing seals to avoid injury. All components must be cleaned thoroughly before assembly and lubricated with oil during reassembly.
Caterpillar Cat 336D2 L Excavator (Prefix ELR) Service Repair Manual (ELR0000...cnp692569
This document provides instructions for removing and installing the unit injector hydraulic pump on Caterpillar C9 engines. The removal process involves disconnecting fuel lines and electrical connections, removing mounting bolts, and taking out the O-ring seal. Installation is the reverse of removal, and includes cleaning parts, applying a new O-ring seal, reconnecting lines and bolts, and filling fluids to the proper levels. Procedures are provided for pumps with both non-dual and dual tapered roller bearings.
The document provides instructions for removing and installing the unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting fuel lines and electrical connections, removing mounting bolts, and taking out the pump. The installation procedure specifies cleaning parts, applying a new O-ring seal, positioning the pump, and securing it with bolts. Proper containment of fluids is emphasized during maintenance.
Caterpillar Cat 336D2 L Excavator (Prefix ELR) Service Repair Manual (ELR0000...zatao0179249295
The document provides instructions for removing and installing the unit injector hydraulic pump on Caterpillar C9 engines. The removal procedure involves disconnecting fuel lines and electrical connections, removing mounting bolts, and taking out the pump. The installation procedure specifies cleaning parts, applying a new O-ring seal, positioning the pump, and securing it with bolts. Proper containment of fluids is emphasized during maintenance.
This document provides instructions for removing and installing the unit injector hydraulic pump on Caterpillar C9 engines. The removal process involves disconnecting fuel lines and electrical connections, removing mounting bolts, and taking out the O-ring seal. Installation is the reverse, applying a new O-ring seal and grease, positioning the pump, and reconnecting all lines and bolts. Proper cleaning and containment of fluids is emphasized to prevent contamination.
Caterpillar Cat 336D2 L Excavator (Prefix ELR) Service Repair Manual (ELR0000...kesi7153062
This document provides instructions for removing and installing the unit injector hydraulic pump on Caterpillar C9 engines. The removal process involves disconnecting fuel lines and electrical connections, removing mounting bolts, and taking out the pump. Installation is the reverse, applying a new O-ring seal and reconnecting all lines. Proper cleaning and containment of fluids is emphasized. The document outlines procedures for both non-dual and dual tapered roller bearing pump types.
This document provides instructions for removing and installing the unit injector hydraulic pump on Caterpillar C9 engines. The removal process involves disconnecting fuel lines and electrical connections, removing mounting bolts, and taking out the pump. Installation is the reverse, applying a new O-ring seal and reconnecting all lines. Proper cleaning and containment of fluids is emphasized. Both non-dual and dual tapered roller bearing pump types are covered.
1. The document provides instructions for removing and installing the flywheel and crankshaft rear seal on a C7.1 engine that powers a 323 excavator.
2. To remove the flywheel, bolts must first be removed and guide studs installed before lifting the flywheel off using a lifting device. The ring gear can then be removed by heating and pressing it off.
3. Flywheel installation requires cleaning and inspecting components, heating and pressing the ring gear if replaced, and torquing bolts with the flywheel secured to prevent rotation.
4. Crankshaft rear seal removal requires removing screws using a Torx socket after removing the flywheel housing. The sealed assembly
Caterpillar Cat 326D2 (Prefix KGY) Service Repair Manual (KGY00001 and up).pdfkm7seydwuhdw
This document provides instructions for disassembling and assembling the travel motor of a 326D2 excavator. It lists the required tools and gives step-by-step procedures to remove and install various components of the travel motor such as the head, bearings, brake piston, seals, and housing covers. Special care must be taken when handling springs or installing seals to avoid injury. All components must be cleaned thoroughly before assembly and lubricated with oil during reassembly.
Crown TSP6000 Series Turret Order Picker Parts Catalogue Manual.pdfkm7seydwuhdw
This document is a parts manual for the power unit of a TSP6000 series truck. It contains 30 numbered parts that make up the power unit, including the power unit housing, doors, covers, screws, nuts, and other minor components. Next to each numbered part is the corresponding part number and a brief description. The parts are organized by their location and function within the power unit.
The document provides instructions for removing and installing engine components, including:
- Removing and installing inlet and exhaust valves, which requires using a valve spring compressor tool
- Removing and installing inlet and exhaust valve guides using driver tools
- Removing and installing inlet and exhaust valve seat inserts, which requires a valve seat extractor tool kit
- Removing the engine oil filter base using a strap wrench tool
The procedures describe the required tools and provide illustrations of the component removal and installation steps. Safety notices are included to keep parts clean and contain fluids properly during maintenance.
Crown WAV50 Work Assit Vehicle Parts Catalogue Manual.pdfkm7seydwuhdw
This parts manual provides exploded diagrams and part lists for the WAV 50 Series order number 812718-006. It includes 10 sections covering the chassis front and rear, axle, hydraulic unit, drive unit, electrical parts, mast/lift structure, cylinder, cabin/platform, miscellaneous service information, and labels/decals. The document provides overview diagrams and indexes that list each part number, name, and quantity required to service or repair the truck.
1. The document provides step-by-step instructions for disassembling and assembling the travel motor of a 324E LN excavator.
2. It details 27 steps to disassemble components like the head, brake piston, rotating assembly, and seals.
3. The 28 steps for assembly instruct to reinstall these components in reverse order and note proper alignment of parts, use of lubrication and tools.
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It describes:
1) Removing the electric starting motor, flywheel, and ring gear before removing the flywheel housing.
2) Using lifting tools to remove the flywheel housing bolts and separate the housing from the cylinder block.
3) Installing a new gasket and oil seal before reinstalling the housing and torquing the bolts.
4) Reinstalling the flywheel and electric starting motor after installing the flywheel housing.
Crown ST3000 Series Forklift Service Repair Manual.pdfkm7seydwuhdw
This document provides a service manual for the ST3000 series truck. It contains sections covering safety, introduction/use of the manual, lubrication and adjustment procedures, hydraulics, the drive unit, and electrical systems. The manual includes information on component access, recommended lubricants, maintenance schedules, hydraulic and electrical symbols, and troubleshooting charts to assist with repairs.
Crown SC3016 Forklift Parts Catalogue Manual.pdfkm7seydwuhdw
This document is a parts manual that contains a table of contents listing replacement parts for an SC3000 series machine. The table of contents includes over 50 part descriptions organized into 7 sections related to the power unit, hydraulic system, drive unit, electrical system, brakes, steering, and mast/lift structure. Each part listing includes the part's page number and identification number for reference in the manual.
Crown SC3013 Forklift Parts Catalogue Manual.pdfkm7seydwuhdw
This document is a parts manual for a SC3000 series truck. It contains:
- A table of contents listing the document sections and part descriptions with corresponding page numbers and identification numbers.
- A section on safety information and general maintenance guidelines.
- An introduction providing information on operating instructions, service training, and part ordering.
- The document is organized into sections covering the truck's power unit, hydraulic, drive, electrical, brake, steering, mast/lift, cylinder, and miscellaneous parts. Each section lists the relevant parts with identification numbers to order replacements.
This document provides instructions for disassembling the final drive, travel motor, and other components of an excavator model 312D2. It lists the required tools and gives step-by-step procedures to remove parts like sprockets, valves, gears, plates, and seals. Safety warnings are provided to release pressures and springs carefully due to risk of injury from propelled parts. Detailed illustrations accompany each step to ensure correct reassembly.
This document provides instructions to disassemble a final drive on a 325D MH EXCAVATOR. It outlines 31 steps to remove components like the cover, gears, carrier assemblies, housing and seals. Special tools are required and cleanliness is important to prevent dirt from entering during reassembly. Weights of components are provided to assist with removal.
This document provides instructions for disassembling components of an excavator including the final drive, travel motor, counterbalance valve, and barrel assembly. It lists required tools and outlines multi-step procedures involving removing fittings, draining fluids, loosening bolts, using pullers to remove bearings and seals, and carefully disassembling internal parts while keeping components in order for reassembly. Safety notices warn of risks such as fluid pressure, heavy lifting, and released spring forces.
The document provides instructions for installing and removing several engine components on a Caterpillar 312D excavator including:
1. Installing the flywheel which requires heating the ring gear, pressing it onto the flywheel, and securing it with bolts.
2. Removing and installing the crankshaft rear seal using tools like a slide hammer and seal distorter.
3. Installing the crankshaft rear seal which involves cleaning surfaces, applying retaining compound, and using an installer tool.
4. Removing and installing the flywheel housing which requires lifting tools and removing/installing bolts, seals and gaskets.
The document provides instructions for disassembling and assembling the swing drive of a 312C excavator. It describes removing over 20 individual parts in 16 steps for disassembly, including the sun gear, carrier assembly, ring gear, planetary gears, shafts, bearings, and housing components. Reassembly involves installing the same parts in the reverse order over 17 steps, applying sealant and fasteners, and noting torque specifications. The overall process handles each part with care to prevent contamination and properly position components using lifting devices and presses.
The document provides the disassembly procedure for a travel motor in 27 steps. It begins by removing the travel motor and cleaning it. Key steps include removing the head, brake piston, friction plates, and barrel assembly. Small components like seals, springs, and races are also removed. Precise identification marks are needed to ensure correct reassembly of small parts and piston shoe assemblies in their original locations. Tools required for the disassembly are also listed.
Caterpillar Cat 324E L Excavator (Prefix TLF) Service Repair Manual (TLF00001...km7seydwuhdw
This document provides instructions for disassembling and assembling the travel motor of 324E L and 324E LN Excavator models. It lists the required tools and parts and provides step-by-step instructions and illustrations for removing and installing components like the motor head, brake piston, rotating assembly, bearings, seals, and more. Precautions are included to properly handle springs and ensure correct positioning of parts.
Caterpillar Cat 312D L Excavator (Prefix HCW) Service Repair Manual (HCW00001...km7seydwuhdw
This document provides instructions for installing the crankshaft in a Caterpillar 312D or 312D L excavator. It involves the following steps:
1. Install the thrust washer and upper halves of the main bearings in the cylinder block. Lubricate and position the crankshaft onto the bearings.
2. Install the lower main bearings onto the bearing caps and rear cap. Lubricate and install seals in the rear cap grooves.
3. Install the bearing caps and tighten the bolts to specification. Check crankshaft end play and install the connecting rods, pistons, and remaining components.
This document provides instructions for removing and installing various engine components on a Caterpillar 325C excavator, including:
- Removing and installing the flywheel, which requires the use of lifting tools and bolts are tightened to a specified torque.
- Removing the crankshaft rear seal using drilling and hammering tools, taking care not to damage surfaces.
- Installing the rear seal using a seal installer tool.
- Procedures for removing and installing the flywheel housing and vibration damper/pulley that involve cleaning surfaces, applying sealant, and tightening bolts.
Caterpillar Cat 312D L Excavator (Prefix KES) Service Repair Manual (KES00001...km7seydwuhdw
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It describes:
1) Removing the electric starting motor, flywheel, and ring gear before removing the flywheel housing.
2) Using lifting tools to remove the flywheel housing bolts and separate the housing from the cylinder block.
3) Installing a new gasket and oil seal before reinstalling the flywheel housing with bolts and reattaching the flywheel and starting motor.
This document provides instructions for assembling a travel motor for excavator models 324E and 324E L. The 28 step assembly process includes installing various components like seals, bearings, plates, springs and retaining rings in the correct order. Tools required include retaining ring pliers, drivers, pullers and adapters. Precautions are outlined such as lubricating parts, noting alignment marks, and taking care when installing spring loaded components.
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves 28 steps to remove components like the head, brake piston, rotating assembly, bearings and seals. The assembly process reverses the disassembly with 23 steps, applying lubricant and torque specifications where required to reinstall components in the correct orientation. Tools including adapters, eyebolts, retaining ring pliers and presses are listed to facilitate the work.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Crown TSP6000 Series Turret Order Picker Parts Catalogue Manual.pdfkm7seydwuhdw
This document is a parts manual for the power unit of a TSP6000 series truck. It contains 30 numbered parts that make up the power unit, including the power unit housing, doors, covers, screws, nuts, and other minor components. Next to each numbered part is the corresponding part number and a brief description. The parts are organized by their location and function within the power unit.
The document provides instructions for removing and installing engine components, including:
- Removing and installing inlet and exhaust valves, which requires using a valve spring compressor tool
- Removing and installing inlet and exhaust valve guides using driver tools
- Removing and installing inlet and exhaust valve seat inserts, which requires a valve seat extractor tool kit
- Removing the engine oil filter base using a strap wrench tool
The procedures describe the required tools and provide illustrations of the component removal and installation steps. Safety notices are included to keep parts clean and contain fluids properly during maintenance.
Crown WAV50 Work Assit Vehicle Parts Catalogue Manual.pdfkm7seydwuhdw
This parts manual provides exploded diagrams and part lists for the WAV 50 Series order number 812718-006. It includes 10 sections covering the chassis front and rear, axle, hydraulic unit, drive unit, electrical parts, mast/lift structure, cylinder, cabin/platform, miscellaneous service information, and labels/decals. The document provides overview diagrams and indexes that list each part number, name, and quantity required to service or repair the truck.
1. The document provides step-by-step instructions for disassembling and assembling the travel motor of a 324E LN excavator.
2. It details 27 steps to disassemble components like the head, brake piston, rotating assembly, and seals.
3. The 28 steps for assembly instruct to reinstall these components in reverse order and note proper alignment of parts, use of lubrication and tools.
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It describes:
1) Removing the electric starting motor, flywheel, and ring gear before removing the flywheel housing.
2) Using lifting tools to remove the flywheel housing bolts and separate the housing from the cylinder block.
3) Installing a new gasket and oil seal before reinstalling the housing and torquing the bolts.
4) Reinstalling the flywheel and electric starting motor after installing the flywheel housing.
Crown ST3000 Series Forklift Service Repair Manual.pdfkm7seydwuhdw
This document provides a service manual for the ST3000 series truck. It contains sections covering safety, introduction/use of the manual, lubrication and adjustment procedures, hydraulics, the drive unit, and electrical systems. The manual includes information on component access, recommended lubricants, maintenance schedules, hydraulic and electrical symbols, and troubleshooting charts to assist with repairs.
Crown SC3016 Forklift Parts Catalogue Manual.pdfkm7seydwuhdw
This document is a parts manual that contains a table of contents listing replacement parts for an SC3000 series machine. The table of contents includes over 50 part descriptions organized into 7 sections related to the power unit, hydraulic system, drive unit, electrical system, brakes, steering, and mast/lift structure. Each part listing includes the part's page number and identification number for reference in the manual.
Crown SC3013 Forklift Parts Catalogue Manual.pdfkm7seydwuhdw
This document is a parts manual for a SC3000 series truck. It contains:
- A table of contents listing the document sections and part descriptions with corresponding page numbers and identification numbers.
- A section on safety information and general maintenance guidelines.
- An introduction providing information on operating instructions, service training, and part ordering.
- The document is organized into sections covering the truck's power unit, hydraulic, drive, electrical, brake, steering, mast/lift, cylinder, and miscellaneous parts. Each section lists the relevant parts with identification numbers to order replacements.
This document provides instructions for disassembling the final drive, travel motor, and other components of an excavator model 312D2. It lists the required tools and gives step-by-step procedures to remove parts like sprockets, valves, gears, plates, and seals. Safety warnings are provided to release pressures and springs carefully due to risk of injury from propelled parts. Detailed illustrations accompany each step to ensure correct reassembly.
This document provides instructions to disassemble a final drive on a 325D MH EXCAVATOR. It outlines 31 steps to remove components like the cover, gears, carrier assemblies, housing and seals. Special tools are required and cleanliness is important to prevent dirt from entering during reassembly. Weights of components are provided to assist with removal.
This document provides instructions for disassembling components of an excavator including the final drive, travel motor, counterbalance valve, and barrel assembly. It lists required tools and outlines multi-step procedures involving removing fittings, draining fluids, loosening bolts, using pullers to remove bearings and seals, and carefully disassembling internal parts while keeping components in order for reassembly. Safety notices warn of risks such as fluid pressure, heavy lifting, and released spring forces.
The document provides instructions for installing and removing several engine components on a Caterpillar 312D excavator including:
1. Installing the flywheel which requires heating the ring gear, pressing it onto the flywheel, and securing it with bolts.
2. Removing and installing the crankshaft rear seal using tools like a slide hammer and seal distorter.
3. Installing the crankshaft rear seal which involves cleaning surfaces, applying retaining compound, and using an installer tool.
4. Removing and installing the flywheel housing which requires lifting tools and removing/installing bolts, seals and gaskets.
The document provides instructions for disassembling and assembling the swing drive of a 312C excavator. It describes removing over 20 individual parts in 16 steps for disassembly, including the sun gear, carrier assembly, ring gear, planetary gears, shafts, bearings, and housing components. Reassembly involves installing the same parts in the reverse order over 17 steps, applying sealant and fasteners, and noting torque specifications. The overall process handles each part with care to prevent contamination and properly position components using lifting devices and presses.
The document provides the disassembly procedure for a travel motor in 27 steps. It begins by removing the travel motor and cleaning it. Key steps include removing the head, brake piston, friction plates, and barrel assembly. Small components like seals, springs, and races are also removed. Precise identification marks are needed to ensure correct reassembly of small parts and piston shoe assemblies in their original locations. Tools required for the disassembly are also listed.
Caterpillar Cat 324E L Excavator (Prefix TLF) Service Repair Manual (TLF00001...km7seydwuhdw
This document provides instructions for disassembling and assembling the travel motor of 324E L and 324E LN Excavator models. It lists the required tools and parts and provides step-by-step instructions and illustrations for removing and installing components like the motor head, brake piston, rotating assembly, bearings, seals, and more. Precautions are included to properly handle springs and ensure correct positioning of parts.
Caterpillar Cat 312D L Excavator (Prefix HCW) Service Repair Manual (HCW00001...km7seydwuhdw
This document provides instructions for installing the crankshaft in a Caterpillar 312D or 312D L excavator. It involves the following steps:
1. Install the thrust washer and upper halves of the main bearings in the cylinder block. Lubricate and position the crankshaft onto the bearings.
2. Install the lower main bearings onto the bearing caps and rear cap. Lubricate and install seals in the rear cap grooves.
3. Install the bearing caps and tighten the bolts to specification. Check crankshaft end play and install the connecting rods, pistons, and remaining components.
This document provides instructions for removing and installing various engine components on a Caterpillar 325C excavator, including:
- Removing and installing the flywheel, which requires the use of lifting tools and bolts are tightened to a specified torque.
- Removing the crankshaft rear seal using drilling and hammering tools, taking care not to damage surfaces.
- Installing the rear seal using a seal installer tool.
- Procedures for removing and installing the flywheel housing and vibration damper/pulley that involve cleaning surfaces, applying sealant, and tightening bolts.
Caterpillar Cat 312D L Excavator (Prefix KES) Service Repair Manual (KES00001...km7seydwuhdw
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It describes:
1) Removing the electric starting motor, flywheel, and ring gear before removing the flywheel housing.
2) Using lifting tools to remove the flywheel housing bolts and separate the housing from the cylinder block.
3) Installing a new gasket and oil seal before reinstalling the flywheel housing with bolts and reattaching the flywheel and starting motor.
This document provides instructions for assembling a travel motor for excavator models 324E and 324E L. The 28 step assembly process includes installing various components like seals, bearings, plates, springs and retaining rings in the correct order. Tools required include retaining ring pliers, drivers, pullers and adapters. Precautions are outlined such as lubricating parts, noting alignment marks, and taking care when installing spring loaded components.
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves 28 steps to remove components like the head, brake piston, rotating assembly, bearings and seals. The assembly process reverses the disassembly with 23 steps, applying lubricant and torque specifications where required to reinstall components in the correct orientation. Tools including adapters, eyebolts, retaining ring pliers and presses are listed to facilitate the work.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 L EXCAVATOR ELR
Configuration: 336D2 & 336D2 L Excavators ELR00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
C9 Engines for Caterpillar Built Machines
Media Number -RENR9579-20 Publication Date -01/02/2015 Date Updated -15/08/2018
i06737900
Unit Injector Sleeve - Remove
SMCS - 1713-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-3042 Plug Tap 1
B 221-0052 Guide Sleeve 1
C
9U-6858 Bridge Plate 1
1B-2886 Bolts 2
221-9778 Puller Stud 1
4K-0367 Full Nut 1
5P-8247 Hard Washer 1
9U-6877 Thrust Bearing 1
D 221-9803 Rubber Stopper 1
Start By:
a. Remove the unit injectors. Refer to Disassembly and Assembly, "Unit Injector - Remove".
NOTICE
Keep all parts clean from contaminants.
1/3
336D2 & 336D2 L Excavators ELR00001-UP (MACHINE) POWERED BY C9 Engin...
2020/5/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
1. Drain the coolant from the cooling system into a suitable container for storage or disposal.
Refer to Operation and Maintenance Manual, "Refill Capacities and Recommendations".
2. Position Tooling (D) at the bottom of the unit injector sleeve.
3. Coat Tooling (A) with clean grease. Use Tooling (A) and Tooling (B) to cut threads into the
unit injector sleeve.
2/3
336D2 & 336D2 L Excavators ELR00001-UP (MACHINE) POWERED BY C9 Engin...
2020/5/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 1 g01137445
4. Install Tooling (C) in unit injector sleeve (1).
5. Remove unit injector sleeve (1). Remove the O-ring seals.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue May 26 16:53:29 UTC+0800 2020
3/3
336D2 & 336D2 L Excavators ELR00001-UP (MACHINE) POWERED BY C9 Engin...
2020/5/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 L EXCAVATOR ELR
Configuration: 336D2 & 336D2 L Excavators ELR00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
C9 Engines for Caterpillar Built Machines
Media Number -RENR9579-20 Publication Date -01/02/2015 Date Updated -15/08/2018
i03742983
Unit Injector Sleeve - Install
SMCS - 1713-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
E 221-9777 Sleeve Installer 1
F 4C-5552 Large Bore Brush 1
G 4C-9507 Retaining Compound 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Thoroughly clean the unit injector sleeves and the bores for the unit injectors with Tooling
(F) .
1/2
336D2 & 336D2 L Excavators ELR00001-UP (MACHINE) POWERED BY C9 Engin...
2020/5/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 1 g02021929
2. Apply clean engine oil to O-ring seals (2) . Install O-ring seals (2) on unit injector sleeve
(1) .
3. Position unit injector sleeve (1) on Tooling (E) .
4. Apply a thin coating of Tooling (G) around the outer circumference of unit injector sleeve
(1) at Area (C) .
5. Position unit injector sleeve (1) in the cylinder head. Use a hammer to install unit injector
sleeve (1) in the cylinder head.
Note: Allow Tooling (G) to cure for two hours at 21 °C (70 °F) before filling the engine
with fuel or coolant. Longer curing time is required for lower temperatures.
6. Fill the cooling system with coolant to the correct level. Refer to Operation and
Maintenance Manual, "Refill Capacities and Recommendations".
End By: Install the unit injectors. Refer to Disassembly and Assembly, "Unit Injector - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue May 26 16:54:25 UTC+0800 2020
2/2
336D2 & 336D2 L Excavators ELR00001-UP (MACHINE) POWERED BY C9 Engin...
2020/5/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 L EXCAVATOR ELR
Configuration: 336D2 & 336D2 L Excavators ELR00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
C9 Engines for Caterpillar Built Machines
Media Number -RENR9579-20 Publication Date -01/02/2015 Date Updated -15/08/2018
i05701078
Unit Injector Hydraulic Pump - Remove
SMCS - 1714-011
Removal Procedure for Non-Dual Tapered Roller Bearing
HEUI Pump
Start By:
A. Remove fuel filter base, if necessary.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/8
336D2 & 336D2 L Excavators ELR00001-UP (MACHINE) POWERED BY C9 Engin...
2020/5/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 1 g03601539
Non-Dual Taper Roller Bearing HEUI pump
Illustration 2 g03601540
Dual Taper Roller Bearing HEUI pump
Note: Refer to Illustrations 1 and 2 in order to identify each unit injection hydraulic pump.
2/8
336D2 & 336D2 L Excavators ELR00001-UP (MACHINE) POWERED BY C9 Engin...
2020/5/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 3 g03614617
1. Disconnect tube assemblies (3) , (4) , (5) , and (6) .
2. Disconnect hose assembly (7) .
3. Disconnect harness assembly (2) from unit injector hydraulic pump (1) .
3/8
336D2 & 336D2 L Excavators ELR00001-UP (MACHINE) POWERED BY C9 Engin...
2020/5/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 4 g03614660
4. Support unit injector hydraulic pump (1) by hand and remove bolts (8) . Remove unit
injector hydraulic pump (1) .
4/8
336D2 & 336D2 L Excavators ELR00001-UP (MACHINE) POWERED BY C9 Engin...
2020/5/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 5 g03614696
5. Remove O-ring seal (9) .
Removal Procedure for Dual Tapered Roller Bearing HEUI
Pump
Start By:
A. Remove fuel filter base, if necessary.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
5/8
336D2 & 336D2 L Excavators ELR00001-UP (MACHINE) POWERED BY C9 Engin...
2020/5/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 6 g03615086
1. Disconnect harness assembly (1) . Disconnect hose assemblies (4) and tube assembly (3) .
Remove tube assembly (2) and tube assembly (5) .
6/8
336D2 & 336D2 L Excavators ELR00001-UP (MACHINE) POWERED BY C9 Engin...
2020/5/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 7 g03615089
2. Support unit injector hydraulic pump (7) and remove bolts (6) .
Illustration 8 g03615416
3. Rotate counterclockwise as shown, then remove unit injector hydraulic pump (7) .
7/8
336D2 & 336D2 L Excavators ELR00001-UP (MACHINE) POWERED BY C9 Engin...
2020/5/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 9 g03615091
4. Remove O-ring seal (8) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue May 26 16:55:21 UTC+0800 2020
8/8
336D2 & 336D2 L Excavators ELR00001-UP (MACHINE) POWERED BY C9 Engin...
2020/5/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 L EXCAVATOR ELR
Configuration: 336D2 & 336D2 L Excavators ELR00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
C9 Engines for Caterpillar Built Machines
Media Number -RENR9579-20 Publication Date -01/02/2015 Date Updated -15/08/2018
i05701091
Unit Injector Hydraulic Pump - Install
SMCS - 1714-012
Installation Procedure for Non-Dual Taper Roller Bearing
HEUI Pump
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/9
336D2 & 336D2 L Excavators ELR00001-UP (MACHINE) POWERED BY C9 Engin...
2020/5/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 1 g03601539
Non-Dual Taper Roller Bearing HEUI pump
Illustration 2 g03601540
Dual Taper Roller Bearing HEUI pump
Note: Refer to Illustrations 1 and 2 in order to identify each unit injection hydraulic pump.
2/9
336D2 & 336D2 L Excavators ELR00001-UP (MACHINE) POWERED BY C9 Engin...
2020/5/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 3 g03614696
1. Install new O-ring seal (9) .
3/9
336D2 & 336D2 L Excavators ELR00001-UP (MACHINE) POWERED BY C9 Engin...
2020/5/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 4 g03614660
2. Position unit injector hydraulic pump (1) in the front housing.
3. Support unit injector hydraulic pump (1) and install bolts (8) .
4/9
336D2 & 336D2 L Excavators ELR00001-UP (MACHINE) POWERED BY C9 Engin...
2020/5/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 5 g03614617
4. Connect hose assembly (7) .
5. Connect tube assemblies (3) , (4) , (5) , and (6) .
6. Connect harness assembly (2) to unit injector hydraulic pump (1) .
Installation Procedure for Dual Tapered Roller Bearing
HEUI Pump
Table 1
Required Tools
Tool Part Number Part Description Qty
A 129-1967 Multipurpose Grease -
Note: If replacing a non-dual tapered roller bearing HEUI pump with a dual tapered roller bearing
HEUI pump, refer to Special Instruction, REHS7902 for rework and installation procedures.
5/9
336D2 & 336D2 L Excavators ELR00001-UP (MACHINE) POWERED BY C9 Engin...
2020/5/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 6 g03601539
Non-Dual Taper Roller Bearing HEUI pump
Illustration 7 g03601540
Dual Taper Roller Bearing HEUI pump
Note: Refer to Illustrations 6 and 7 in order to identify each unit injection hydraulic pump.
Note: If a dowel pin is installed in the mounting flange of the unit injector hydraulic pump
or in the front housing at the unit injector hydraulic pump mounting location, remove the
dowel pin before installing the unit injector hydraulic pump.
6/9
336D2 & 336D2 L Excavators ELR00001-UP (MACHINE) POWERED BY C9 Engin...
2020/5/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 8 g03615091
1. Install O-ring seal (8) . Apply Tooling (A) to O-ring seal (8) , the mounting flange of the
unit injector hydraulic pump, and the back of the front housing at the mounting location of
the unit injector hydraulic pump.
Illustration 9 g03615798
2. Position unit injector hydraulic pump (7) as shown, then rotate clockwise to final
installation orientation.
7/9
336D2 & 336D2 L Excavators ELR00001-UP (MACHINE) POWERED BY C9 Engin...
2020/5/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 10 g03615089
3. Install bolts (6) hand-tight.
Note: Do not fully tighten bolts (6) until all of the hoses and the tubes are connected to unit
injection hydraulic pump (7) .
Illustration 11 g03615086
4. Install tube assembly (5) hand-tight.
5. Connect hose assemblies (4) . Install tube assembly (3) and tube assembly (2) hand-tight.
6. Tighten bolts (6) to a torque of 55 ± 10 N·m (41 ± 7 lb ft).
8/9
336D2 & 336D2 L Excavators ELR00001-UP (MACHINE) POWERED BY C9 Engin...
2020/5/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. 7. Tighten tube assemblies (2) , (3) , (5) and hose assemblies (4) .
8. Connect harness assembly (1) .
End By: Install fuel filter base, if necessary.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue May 26 16:56:17 UTC+0800 2020
9/9
336D2 & 336D2 L Excavators ELR00001-UP (MACHINE) POWERED BY C9 Engin...
2020/5/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 L EXCAVATOR ELR
Configuration: 336D2 & 336D2 L Excavators ELR00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
C9 Engines for Caterpillar Built Machines
Media Number -RENR9579-20 Publication Date -01/02/2015 Date Updated -15/08/2018
i02297056
Turbocharger - Remove
SMCS - 1052-011
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
1/2
336D2 & 336D2 L Excavators ELR00001-UP (MACHINE) POWERED BY C9 Engin...
2020/5/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
26. Illustration 1 g01150421
1. Disconnect hose assembly (1).
2. Remove bolts (4) and tube assembly (5).
3. Attach a suitable lifting device onto turbocharger (2). The weight of turbocharger (2) is
approximately 27 kg (60 lb). Remove nuts (3). Remove turbocharger (2) and the gasket.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue May 26 16:57:13 UTC+0800 2020
2/2
336D2 & 336D2 L Excavators ELR00001-UP (MACHINE) POWERED BY C9 Engin...
2020/5/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 L EXCAVATOR ELR
Configuration: 336D2 & 336D2 L Excavators ELR00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
C9 Engines for Caterpillar Built Machines
Media Number -RENR9579-20 Publication Date -01/02/2015 Date Updated -15/08/2018
i04000968
Turbocharger - Install
SMCS - 1052-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5P-3931 Anti-Seize Compound -
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Apply Tooling (A) to the turbocharger mounting studs on the exhaust manifold.
1/2
336D2 & 336D2 L Excavators ELR00001-UP (MACHINE) POWERED BY C9 Engin...
2020/5/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Illustration 1 g01150421
2. Attach a suitable lifting device to turbocharger (2). The weight of turbocharger (2) is
approximately 27 kg (60 lb). Position the gasket and turbocharger (2) on the exhaust
manifold.
Note: Discard the nuts after use. Use new nuts for installation.
3. Install nuts (3). Tighten nuts (3) to a torque of 54 ± 5 N·m (40 ± 4 lb ft).
4. Position tube assembly (5) and install bolts (4).
5. Connect hose assembly (1).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue May 26 16:58:08 UTC+0800 2020
2/2
336D2 & 336D2 L Excavators ELR00001-UP (MACHINE) POWERED BY C9 Engin...
2020/5/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...