This document provides instructions for disassembling and assembling the travel motor of a 325B L excavator. It outlines 27 steps to disassemble the various components of the travel motor including removing the head, brake piston, barrel assembly, shoe retainer, and shaft assembly. It then describes the 25 steps to reassemble these components, noting the proper order and orientation needed to ensure correct assembly. Precautions are highlighted such as applying identification marks and cleaning components thoroughly before assembly.
Caterpillar cat 325 b excavator (prefix 8gm) service repair manual (8gm00001 ...fjsjjekdkme
1) The document provides step-by-step instructions for disassembling and assembling the mechanical components of an excavator fan, including removing the fan blades, bellcrank assembly, hub assembly, carrier/spool assembly, and bushings.
2) The procedures include draining oil from the fan assembly, using air pressure to test for leaks, and removing seals, bearings, and other individual parts.
3) Troubleshooting instructions are provided for accessing parts if the through shaft is damaged or other issues are encountered during disassembly.
Kobelco sk250 10 hydraulic excavator service repair manualfjsjjekdkme
This document outlines general precautions and guidelines for repairing excavator equipment according to the shop manual. It discusses preparing for disassembly, safety during disassembly and assembly, handling hydraulic and electrical equipment, welding repairs, and environmental issues. The outline notes that the copyright belongs to Kobelco and outlines rules for copying or distributing the manual's contents. It also introduces the international unit system used in specifications.
Caterpillar cat 325 c l excavator (prefix csj) service repair manual (csj0000...fjsjjekdkme
This document provides instructions for disassembling and assembling the travel motor of a 325C excavator. The disassembly procedure involves 27 steps to remove components like the head, check valves, fittings, seals, brake piston, friction plates, barrel assembly, and shaft assembly. The assembly procedure describes 21 steps and includes applying seals and lubricants to reinstall the components in reverse order of disassembly. Special care must be taken with alignment marks and component positions during reassembly.
Caterpillar cat 325 b excavator (prefix 8fn) service repair manual (8fn00001 ...fjsjjekdkme
This document provides instructions for removing and installing a cylinder head on an excavator. It begins by listing other components that must first be removed, such as the fuel filter base, governor, fuel linkage, and manifolds. The removal procedure then instructs technicians to attach a lifting device to the cylinder head and remove bolts holding it to the cylinder block before removing the gasket. The installation procedure lists cleaning the mating surfaces and applying lubricant to the gasket before positioning the head and torquing the bolts to specifications.
Caterpillar cat 325 c excavator (prefix crb) service repair manual (crb00001 ...fjsjjekdkme
The document provides instructions for removing and installing the camshaft on a Caterpillar 3126B engine used in 325C excavators. The summary is:
1) Remove the lifter group and front cover to access the camshaft. Wire the valve lifters away from the camshaft. Remove the camshaft retainer plate and bolts, then remove the camshaft.
2) Install the camshaft, ensuring the timing marks are aligned. Install the camshaft retainer plate and bolts. Install the lifter group and front cover.
3) The document provides step-by-step instructions for removing and installing the camshaft, camshaft gear
Caterpillar cat 325 c l excavator (prefix amh) service repair manual (amh0000...fjkskedmme
This document provides instructions for removing and installing various engine components on Caterpillar 325C and 325C L excavators, including:
- Removing and installing the camshaft, camshaft gear, and camshaft bearings. Proper timing of the camshaft is emphasized.
- Removing and installing the engine oil pan. Safety precautions for hot oil and proper fluid containment are outlined.
- The document contains detailed step-by-step instructions, illustrations, and notes on proper component orientation for each procedure. Required tools are listed.
Kawasaki 80 z7b wheel loader service repair manual (serial no. 80c8 5001 and up)fjsjjekdkme
The document contains sections from a shop manual for a wheel loader. It includes sections on general information, component layout, specifications, and maintenance procedures. The component layout sections describe and illustrate the main components of the wheel loader including the engine, hydraulic system, electrical system, cab, drive unit, and other key components. The specifications section lists technical specifications for the engine, operating weights, dimensions, travel speeds and other performance specifications.
Kawasaki 80 z7 wheel loader service repair manual (serial no. 80c6 5001 and up)fjsjjekdkme
This document provides guidelines and precautions for disassembling and assembling components of a wheel loader. It discusses preparing the work area, marking parts for reassembly, cleaning and inspecting components, applying lubricants, and properly tightening bolts and nuts. Proper maintenance following these guidelines helps prevent damage and ensures safe and efficient reassembly.
Caterpillar cat 325 b excavator (prefix 8gm) service repair manual (8gm00001 ...fjsjjekdkme
1) The document provides step-by-step instructions for disassembling and assembling the mechanical components of an excavator fan, including removing the fan blades, bellcrank assembly, hub assembly, carrier/spool assembly, and bushings.
2) The procedures include draining oil from the fan assembly, using air pressure to test for leaks, and removing seals, bearings, and other individual parts.
3) Troubleshooting instructions are provided for accessing parts if the through shaft is damaged or other issues are encountered during disassembly.
Kobelco sk250 10 hydraulic excavator service repair manualfjsjjekdkme
This document outlines general precautions and guidelines for repairing excavator equipment according to the shop manual. It discusses preparing for disassembly, safety during disassembly and assembly, handling hydraulic and electrical equipment, welding repairs, and environmental issues. The outline notes that the copyright belongs to Kobelco and outlines rules for copying or distributing the manual's contents. It also introduces the international unit system used in specifications.
Caterpillar cat 325 c l excavator (prefix csj) service repair manual (csj0000...fjsjjekdkme
This document provides instructions for disassembling and assembling the travel motor of a 325C excavator. The disassembly procedure involves 27 steps to remove components like the head, check valves, fittings, seals, brake piston, friction plates, barrel assembly, and shaft assembly. The assembly procedure describes 21 steps and includes applying seals and lubricants to reinstall the components in reverse order of disassembly. Special care must be taken with alignment marks and component positions during reassembly.
Caterpillar cat 325 b excavator (prefix 8fn) service repair manual (8fn00001 ...fjsjjekdkme
This document provides instructions for removing and installing a cylinder head on an excavator. It begins by listing other components that must first be removed, such as the fuel filter base, governor, fuel linkage, and manifolds. The removal procedure then instructs technicians to attach a lifting device to the cylinder head and remove bolts holding it to the cylinder block before removing the gasket. The installation procedure lists cleaning the mating surfaces and applying lubricant to the gasket before positioning the head and torquing the bolts to specifications.
Caterpillar cat 325 c excavator (prefix crb) service repair manual (crb00001 ...fjsjjekdkme
The document provides instructions for removing and installing the camshaft on a Caterpillar 3126B engine used in 325C excavators. The summary is:
1) Remove the lifter group and front cover to access the camshaft. Wire the valve lifters away from the camshaft. Remove the camshaft retainer plate and bolts, then remove the camshaft.
2) Install the camshaft, ensuring the timing marks are aligned. Install the camshaft retainer plate and bolts. Install the lifter group and front cover.
3) The document provides step-by-step instructions for removing and installing the camshaft, camshaft gear
Caterpillar cat 325 c l excavator (prefix amh) service repair manual (amh0000...fjkskedmme
This document provides instructions for removing and installing various engine components on Caterpillar 325C and 325C L excavators, including:
- Removing and installing the camshaft, camshaft gear, and camshaft bearings. Proper timing of the camshaft is emphasized.
- Removing and installing the engine oil pan. Safety precautions for hot oil and proper fluid containment are outlined.
- The document contains detailed step-by-step instructions, illustrations, and notes on proper component orientation for each procedure. Required tools are listed.
Kawasaki 80 z7b wheel loader service repair manual (serial no. 80c8 5001 and up)fjsjjekdkme
The document contains sections from a shop manual for a wheel loader. It includes sections on general information, component layout, specifications, and maintenance procedures. The component layout sections describe and illustrate the main components of the wheel loader including the engine, hydraulic system, electrical system, cab, drive unit, and other key components. The specifications section lists technical specifications for the engine, operating weights, dimensions, travel speeds and other performance specifications.
Kawasaki 80 z7 wheel loader service repair manual (serial no. 80c6 5001 and up)fjsjjekdkme
This document provides guidelines and precautions for disassembling and assembling components of a wheel loader. It discusses preparing the work area, marking parts for reassembly, cleaning and inspecting components, applying lubricants, and properly tightening bolts and nuts. Proper maintenance following these guidelines helps prevent damage and ensures safe and efficient reassembly.
Caterpillar cat 325 f lcr excavator (prefix xaa) service repair manual (xaa00...fjjskekdmme
This document provides instructions for disassembling and assembling the travel motor of a 325F LCR excavator. It describes 25 steps for disassembly, including removing the head, check valve assemblies, fittings, seals, pistons, and other components. It then describes 11 steps for assembly, including installing seals, bearings, keys, and other parts in the reverse order of disassembly. Personal protective equipment is recommended and cleaning and lubrication of parts is emphasized throughout the process.
Caterpillar cat 325 b l track type excavator (prefix 8pr) service repair manu...fjsjjekdkme
The document provides instructions for disassembling and assembling a travel motor. It lists 27 steps for disassembling the travel motor which include removing components like the head, brake piston, barrel assembly, cam plate and shaft assembly. It then lists 26 steps for assembling the travel motor which involve installing components like the shaft assembly, cam plate, barrel assembly, brake piston and head in the reverse order of disassembly. Precautions are provided to ensure correct alignment of parts and prevent damage during assembly.
Caterpillar cat 323 d sa excavator (prefix nes) service repair manual (nes000...jfdskekdmme
The document provides instructions for removing and installing the flywheel, flywheel housing, and crankshaft rear seal of a C6.4 engine. The flywheel is removed using lifting tools and bolts, while the flywheel housing requires removal of mounting bolts and contains a oil seal. Installation follows the reverse process, ensuring clean surfaces and applying retaining compound to mating parts. Special tools are specified for removing and installing the crankshaft rear seal and wear sleeve.
Caterpillar cat 325 b excavator (prefix 6dn) service repair manual (6dn00001 ...fjsjjekdkme
This service repair manual provides instructions for removing and installing inlet manifolds, valves, and valve guides on Caterpillar 325B and 325B LN excavator engines. The document outlines the required tools and safety procedures, and provides step-by-step instructions with illustrations for each repair procedure. Technicians are advised to keep parts clean, contain fluids properly, and refer to other documents for guidance on reusable components.
This document provides instructions for removing and installing a cylinder head on a C18 industrial engine. It includes:
1) Detailed steps for removing the cylinder head such as disconnecting hoses, sensors, and removing bolts.
2) Instructions for installing seals, gaskets and the cylinder head, applying anti-seize compound to bolts, and tightening the bolts in a specific sequence.
3) Notes about cleaning parts and using new gaskets when installing the cylinder head.
Caterpillar cat 336 f lxe excavator (prefix pfl) service repair manual (pfl00...fjkskedmme
This document provides instructions for disassembling the travel motor on 336F XE and 336F LXE excavator models. The 27-step procedure includes removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals and plates. Detailed illustrations accompany each step to show how to position tools and disassemble individual parts. Safety notices warn of potential spring forces and ensure fluids are contained.
The document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 325-A excavator. It lists the required tools and gives a step-by-step process that includes using a valve seat extractor tool to remove the inserts from the cylinder head and installing new inserts. Safety notices are included to keep parts clean and contain fluids.
Caterpillar cat 321 b lcr track excavator (prefix 2zd) service repair manual ...fujsfskekem
This document provides instructions for removing and installing various fuel system components on a Caterpillar 321B LCR Track Excavator engine, including:
- Fuel priming pump
- Fuel filter base
- Fuel injection lines
It describes removing nuts, bolts, lines, and filters, taking care to plug openings to prevent contamination. Reinstallation involves cleaning parts and reconnecting components with new washers or O-rings as needed, torquing to specifications.
Caterpillar cat d6 r track type tractor (prefix 6fr) service repair manual (6...fjkskedmme
The document provides instructions for removing and installing idler rollers and equalizer bars on a Caterpillar D6R track-type tractor. Key steps include using hoists and tools to remove idlers and bolts/retainers, cleaning and inspecting parts, lubricating seals with isopropyl alcohol, and testing assemblies for leaks before reinstallation. Special tools are required to correctly set seal depths and check end play clearance during assembly.
Caterpillar cat 325 c l excavator (prefix jlc) service repair manual (jlc0000...fjkskedmme
The document provides instructions for checking and servicing components of a Caterpillar 3126B engine, including:
1. Removing and installing a crankshaft rear wear sleeve, which requires using specialty tools to distort and remove the old sleeve before pressing in a new one.
2. Installing the crankshaft, which involves cleaning surfaces, applying oil, and torquing bolts to specifications while checking end play.
3. Removing and installing the crankshaft gear, which requires heating the gear and using a puller and hydraulic press for removal and installation.
4. Checking bearing clearance using a dial indicator in accordance with specifications.
This document provides instructions for installing a flywheel and removing and installing a wet back end flywheel housing on a Caterpillar 320 GC excavator. It describes using guide studs and lifting devices to position the heavy flywheel and housing. Torque specifications and tightening sequences are given for installing mounting bolts. Replacing seals, gaskets and dowels is also covered.
Caterpillar cat m316 d wheeled excavator (prefix w6a) service repair manual (...fujsjefjwerkskemm
This document provides instructions for removing and installing an idler gear on a Caterpillar C6.6 engine. It describes the required tools and steps to:
1) Lock the camshaft and crankshaft in position, remove bolts, and remove the standard or heavy-duty idler gear.
2) Clean and inspect the idler gear components, install the idler gear while aligning timing marks, install bolts, and check end play and backlash.
3) Ensure the number one piston is at top dead center before installing the idler gear in the correct position and alignment.
Caterpillar cat 323 f excavator (prefix mfy) service repair manual (mfy00001 ...jfdskekdmme
This document provides disassembly instructions for a 323F and 323F LN excavator travel motor in 27 steps. It details removing components such as the head assembly, housing assembly, brake piston, friction discs, and rotating group. Proper tooling is required and safety precautions should be followed when releasing spring forces or using pressurized air. The travel motor must be thoroughly cleaned and components reinstalled in their original positions and orientations.
Claas targo k60 telehandlers service repair manualfjskekdmjekm
This document provides instructions for removing and installing the front and rear axles on a CLAAS agricultural machine. Key steps include draining hydraulic pressure and disconnecting electrical components before removing axles. Special care must be taken when removing the heavy axles, using proper lifting equipment. Torque specifications and bleeding procedures are listed for reinstallation. Safety warnings are also provided regarding proper protective equipment and following maintenance procedures.
Kawasaki 80 z7 wheel loader service repair manual (serial no. 80c6 3001 and up)fjsjjekdkme
The document provides layout diagrams and specifications for the components of a Hitachi 80Z7 wheel loader, including the location of the engine, hydraulic pumps, electrical components, radiator assembly, cab, front and rear axles, and other major systems. Specification data is given for the loader's dimensions, bucket capacity, operating weight, tipping load, and engine details. The diagrams show the positioning of the main mechanical and electrical components.
Caterpillar cat 320 d excavator (prefix a8f) service repair manual (a8f00001 ...fujjdfjkksekmem
This document provides instructions for removing and installing various engine components of a Caterpillar 320D L excavator. It describes how to remove and install the crankshaft rear seal using various tools. It also describes removing and installing the flywheel housing, removing the idler gear from the front gear group, and removing and installing the crankshaft front seal. The document provides detailed step-by-step instructions and illustrations for each procedure.
Caterpillar cat 420 d backhoe loader (prefix bkc) service repair manual (bkc0...fujsjfejkskem
This document provides instructions for removing and installing components related to the cylinder head of a Caterpillar 3054C engine, including:
- Draining coolant and oil before removing fuel system components, exhaust manifold, rocker shaft, and glow plugs.
- Removing fuel line, harness, tubes, and bypass tube from cylinder head.
- Gradually loosening and removing cylinder head bolts and lifting off cylinder head using a lifting device.
- Removing cylinder head gasket and noting dowel pin locations.
Caterpillar cat 325 b track type excavator (prefix 8pr) service repair manual...f98soeodidkdk
This document provides instructions for disassembling and assembling a travel motor. It includes 27 steps for disassembling components such as the head, brake piston, barrel assembly, and shaft assembly. It also includes 11 steps for assembling components like the lip seal, shaft assembly, cam plate, and springs back into the travel motor body. Special tools and precautions are noted to properly disassemble and reassemble the travel motor.
Caterpillar cat 325 b l track type excavator (prefix 8pr) service repair manu...f98soeodidkdk
This document provides instructions for disassembling and assembling a travel motor. It includes 27 steps for disassembling components such as the head, brake piston, barrel assembly, and shaft assembly. It also includes 11 steps for assembling components like the lip seal, shaft assembly, cam plate, and springs back into the travel motor body. Special tools and precautions are noted to properly disassemble and reassemble the travel motor.
Caterpillar cat 325 b track type excavator (prefix 8pr) service repair manual...fjsjjekdkme
The document provides instructions for disassembling and assembling a travel motor. It lists 27 steps for disassembling the travel motor which include removing components like the head, brake piston, barrel assembly, cam plate and shaft assembly. It then lists 26 steps for assembling the travel motor, assembling the components in reverse order and ensuring proper installation of seals, plates and alignment of parts. Safety notices are provided to properly contain fluids and avoid damage to components.
Caterpillar Cat 318D2 L Excavator (Prefix XAH) Service Repair Manual Instant ...yu5676962
This document provides instructions for disassembling and assembling the travel motor of a 318D2 L excavator. The disassembly process involves removing 27 different components from the travel motor in a specific sequence. The assembly process reverses the disassembly steps and provides additional warnings to ensure proper installation of components like the cam plate. The instructions are accompanied by illustrations to aid technicians in the field.
Caterpillar Cat 318D2 L Excavator (Prefix XAH) Service Repair Manual Instant ...f8seodkdmdmed3
This document provides instructions for disassembling and assembling the travel motor of a 318D2 L excavator. The disassembly process involves removing 27 different components from the travel motor in a specific sequence. The assembly process reverses the disassembly steps and provides additional warnings to ensure proper installation of components like the cam plate. Precise alignment of parts is critical for correct function of the travel motor.
Caterpillar cat 325 f lcr excavator (prefix xaa) service repair manual (xaa00...fjjskekdmme
This document provides instructions for disassembling and assembling the travel motor of a 325F LCR excavator. It describes 25 steps for disassembly, including removing the head, check valve assemblies, fittings, seals, pistons, and other components. It then describes 11 steps for assembly, including installing seals, bearings, keys, and other parts in the reverse order of disassembly. Personal protective equipment is recommended and cleaning and lubrication of parts is emphasized throughout the process.
Caterpillar cat 325 b l track type excavator (prefix 8pr) service repair manu...fjsjjekdkme
The document provides instructions for disassembling and assembling a travel motor. It lists 27 steps for disassembling the travel motor which include removing components like the head, brake piston, barrel assembly, cam plate and shaft assembly. It then lists 26 steps for assembling the travel motor which involve installing components like the shaft assembly, cam plate, barrel assembly, brake piston and head in the reverse order of disassembly. Precautions are provided to ensure correct alignment of parts and prevent damage during assembly.
Caterpillar cat 323 d sa excavator (prefix nes) service repair manual (nes000...jfdskekdmme
The document provides instructions for removing and installing the flywheel, flywheel housing, and crankshaft rear seal of a C6.4 engine. The flywheel is removed using lifting tools and bolts, while the flywheel housing requires removal of mounting bolts and contains a oil seal. Installation follows the reverse process, ensuring clean surfaces and applying retaining compound to mating parts. Special tools are specified for removing and installing the crankshaft rear seal and wear sleeve.
Caterpillar cat 325 b excavator (prefix 6dn) service repair manual (6dn00001 ...fjsjjekdkme
This service repair manual provides instructions for removing and installing inlet manifolds, valves, and valve guides on Caterpillar 325B and 325B LN excavator engines. The document outlines the required tools and safety procedures, and provides step-by-step instructions with illustrations for each repair procedure. Technicians are advised to keep parts clean, contain fluids properly, and refer to other documents for guidance on reusable components.
This document provides instructions for removing and installing a cylinder head on a C18 industrial engine. It includes:
1) Detailed steps for removing the cylinder head such as disconnecting hoses, sensors, and removing bolts.
2) Instructions for installing seals, gaskets and the cylinder head, applying anti-seize compound to bolts, and tightening the bolts in a specific sequence.
3) Notes about cleaning parts and using new gaskets when installing the cylinder head.
Caterpillar cat 336 f lxe excavator (prefix pfl) service repair manual (pfl00...fjkskedmme
This document provides instructions for disassembling the travel motor on 336F XE and 336F LXE excavator models. The 27-step procedure includes removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals and plates. Detailed illustrations accompany each step to show how to position tools and disassemble individual parts. Safety notices warn of potential spring forces and ensure fluids are contained.
The document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 325-A excavator. It lists the required tools and gives a step-by-step process that includes using a valve seat extractor tool to remove the inserts from the cylinder head and installing new inserts. Safety notices are included to keep parts clean and contain fluids.
Caterpillar cat 321 b lcr track excavator (prefix 2zd) service repair manual ...fujsfskekem
This document provides instructions for removing and installing various fuel system components on a Caterpillar 321B LCR Track Excavator engine, including:
- Fuel priming pump
- Fuel filter base
- Fuel injection lines
It describes removing nuts, bolts, lines, and filters, taking care to plug openings to prevent contamination. Reinstallation involves cleaning parts and reconnecting components with new washers or O-rings as needed, torquing to specifications.
Caterpillar cat d6 r track type tractor (prefix 6fr) service repair manual (6...fjkskedmme
The document provides instructions for removing and installing idler rollers and equalizer bars on a Caterpillar D6R track-type tractor. Key steps include using hoists and tools to remove idlers and bolts/retainers, cleaning and inspecting parts, lubricating seals with isopropyl alcohol, and testing assemblies for leaks before reinstallation. Special tools are required to correctly set seal depths and check end play clearance during assembly.
Caterpillar cat 325 c l excavator (prefix jlc) service repair manual (jlc0000...fjkskedmme
The document provides instructions for checking and servicing components of a Caterpillar 3126B engine, including:
1. Removing and installing a crankshaft rear wear sleeve, which requires using specialty tools to distort and remove the old sleeve before pressing in a new one.
2. Installing the crankshaft, which involves cleaning surfaces, applying oil, and torquing bolts to specifications while checking end play.
3. Removing and installing the crankshaft gear, which requires heating the gear and using a puller and hydraulic press for removal and installation.
4. Checking bearing clearance using a dial indicator in accordance with specifications.
This document provides instructions for installing a flywheel and removing and installing a wet back end flywheel housing on a Caterpillar 320 GC excavator. It describes using guide studs and lifting devices to position the heavy flywheel and housing. Torque specifications and tightening sequences are given for installing mounting bolts. Replacing seals, gaskets and dowels is also covered.
Caterpillar cat m316 d wheeled excavator (prefix w6a) service repair manual (...fujsjefjwerkskemm
This document provides instructions for removing and installing an idler gear on a Caterpillar C6.6 engine. It describes the required tools and steps to:
1) Lock the camshaft and crankshaft in position, remove bolts, and remove the standard or heavy-duty idler gear.
2) Clean and inspect the idler gear components, install the idler gear while aligning timing marks, install bolts, and check end play and backlash.
3) Ensure the number one piston is at top dead center before installing the idler gear in the correct position and alignment.
Caterpillar cat 323 f excavator (prefix mfy) service repair manual (mfy00001 ...jfdskekdmme
This document provides disassembly instructions for a 323F and 323F LN excavator travel motor in 27 steps. It details removing components such as the head assembly, housing assembly, brake piston, friction discs, and rotating group. Proper tooling is required and safety precautions should be followed when releasing spring forces or using pressurized air. The travel motor must be thoroughly cleaned and components reinstalled in their original positions and orientations.
Claas targo k60 telehandlers service repair manualfjskekdmjekm
This document provides instructions for removing and installing the front and rear axles on a CLAAS agricultural machine. Key steps include draining hydraulic pressure and disconnecting electrical components before removing axles. Special care must be taken when removing the heavy axles, using proper lifting equipment. Torque specifications and bleeding procedures are listed for reinstallation. Safety warnings are also provided regarding proper protective equipment and following maintenance procedures.
Kawasaki 80 z7 wheel loader service repair manual (serial no. 80c6 3001 and up)fjsjjekdkme
The document provides layout diagrams and specifications for the components of a Hitachi 80Z7 wheel loader, including the location of the engine, hydraulic pumps, electrical components, radiator assembly, cab, front and rear axles, and other major systems. Specification data is given for the loader's dimensions, bucket capacity, operating weight, tipping load, and engine details. The diagrams show the positioning of the main mechanical and electrical components.
Caterpillar cat 320 d excavator (prefix a8f) service repair manual (a8f00001 ...fujjdfjkksekmem
This document provides instructions for removing and installing various engine components of a Caterpillar 320D L excavator. It describes how to remove and install the crankshaft rear seal using various tools. It also describes removing and installing the flywheel housing, removing the idler gear from the front gear group, and removing and installing the crankshaft front seal. The document provides detailed step-by-step instructions and illustrations for each procedure.
Caterpillar cat 420 d backhoe loader (prefix bkc) service repair manual (bkc0...fujsjfejkskem
This document provides instructions for removing and installing components related to the cylinder head of a Caterpillar 3054C engine, including:
- Draining coolant and oil before removing fuel system components, exhaust manifold, rocker shaft, and glow plugs.
- Removing fuel line, harness, tubes, and bypass tube from cylinder head.
- Gradually loosening and removing cylinder head bolts and lifting off cylinder head using a lifting device.
- Removing cylinder head gasket and noting dowel pin locations.
Caterpillar cat 325 b track type excavator (prefix 8pr) service repair manual...f98soeodidkdk
This document provides instructions for disassembling and assembling a travel motor. It includes 27 steps for disassembling components such as the head, brake piston, barrel assembly, and shaft assembly. It also includes 11 steps for assembling components like the lip seal, shaft assembly, cam plate, and springs back into the travel motor body. Special tools and precautions are noted to properly disassemble and reassemble the travel motor.
Caterpillar cat 325 b l track type excavator (prefix 8pr) service repair manu...f98soeodidkdk
This document provides instructions for disassembling and assembling a travel motor. It includes 27 steps for disassembling components such as the head, brake piston, barrel assembly, and shaft assembly. It also includes 11 steps for assembling components like the lip seal, shaft assembly, cam plate, and springs back into the travel motor body. Special tools and precautions are noted to properly disassemble and reassemble the travel motor.
Caterpillar cat 325 b track type excavator (prefix 8pr) service repair manual...fjsjjekdkme
The document provides instructions for disassembling and assembling a travel motor. It lists 27 steps for disassembling the travel motor which include removing components like the head, brake piston, barrel assembly, cam plate and shaft assembly. It then lists 26 steps for assembling the travel motor, assembling the components in reverse order and ensuring proper installation of seals, plates and alignment of parts. Safety notices are provided to properly contain fluids and avoid damage to components.
Caterpillar Cat 318D2 L Excavator (Prefix XAH) Service Repair Manual Instant ...yu5676962
This document provides instructions for disassembling and assembling the travel motor of a 318D2 L excavator. The disassembly process involves removing 27 different components from the travel motor in a specific sequence. The assembly process reverses the disassembly steps and provides additional warnings to ensure proper installation of components like the cam plate. The instructions are accompanied by illustrations to aid technicians in the field.
Caterpillar Cat 318D2 L Excavator (Prefix XAH) Service Repair Manual Instant ...f8seodkdmdmed3
This document provides instructions for disassembling and assembling the travel motor of a 318D2 L excavator. The disassembly process involves removing 27 different components from the travel motor in a specific sequence. The assembly process reverses the disassembly steps and provides additional warnings to ensure proper installation of components like the cam plate. Precise alignment of parts is critical for correct function of the travel motor.
Caterpillar Cat 318D2 L Excavator (Prefix XAH) Service Repair Manual Instant ...ze6074xunong
This document provides instructions for disassembling and assembling the travel motor of a 318D2 L excavator. The disassembly process involves 27 steps to remove all individual components of the travel motor. Key steps include removing the head, brake piston, barrel assembly, shoe retainer and piston shoe assemblies. The assembly process reverses the disassembly with 27 corresponding steps and provides details on cleaning, lubricating and installing each part in the proper orientation. Tools required include a driver and sealant.
Caterpillar Cat 318D2 L Excavator (Prefix XAH) Service Repair Manual Instant ...gongfuao7509
This document provides instructions for disassembling and assembling the travel motor of a 318D2 L excavator. The disassembly process involves removing 27 different components from the travel motor in a specific sequence. The assembly process reverses the disassembly steps and provides additional warnings to ensure proper installation of components like the cam plate. Precise alignment of parts is critical for correct function of the travel motor.
Caterpillar Cat 318D2 L Excavator (Prefix XAH) Service Repair Manual Instant ...tengtui535
This document provides instructions for disassembling and assembling the travel motor of a 318D2 L excavator. The disassembly process involves removing 27 different components from the travel motor in a specific sequence. The assembly process reverses the disassembly steps and provides additional warnings to ensure proper installation of components like the cam plate. Precise alignment of parts is critical and cleanliness is emphasized throughout the process.
Caterpillar Cat 318D2 L Excavator (Prefix XAH) Service Repair Manual Instant ...f8usejkdmmd8i
This document provides instructions for disassembling and assembling the travel motor of a 318D2 L excavator. The disassembly process involves removing 27 different components from the travel motor in a specific sequence. The assembly process reverses the disassembly steps and provides additional warnings to ensure proper installation of components like the cam plate. Precise alignment of parts is critical for correct function of the travel motor.
Caterpillar cat 318 d2 l excavator (prefix xah) service repair manual (xah000...f9oseikkdks
This document provides instructions for disassembling and assembling the travel motor of a 318D2 L excavator. The disassembly process involves 27 steps to remove all individual components of the travel motor. Key steps include removing the head, brake piston, barrel assembly, shoe retainer and piston shoe assemblies. The assembly process reverses the disassembly with 27 corresponding steps and provides details on cleaning, lubricating and installing each part in the proper orientation. Tools required include a driver and sealant.
Caterpillar Cat 318D2 L Excavator (Prefix XAH) Service Repair Manual (XAH0000...f8usiejdkmdd
This document provides instructions for disassembling and assembling the travel motor of a 318D2 L excavator. The disassembly process involves 27 steps to remove all individual components of the travel motor. Key steps include removing the head, brake piston, barrel assembly, shoe retainer and piston shoe assemblies. The assembly process reverses the disassembly with 27 corresponding steps and provides details on cleaning, lubricating and installing each part in the proper orientation. Tools required include a driver and sealant.
Caterpillar Cat 318D2 L Excavator (Prefix XAH) Service Repair Manual (XAH0000...jfkskmdmmdd
This document provides instructions for disassembling and assembling the travel motor of a 318D2 L excavator. The disassembly process involves 27 steps to remove all individual components of the travel motor. Key steps include removing the head, brake piston, barrel assembly, shoe retainer and piston shoe assemblies. The assembly process reverses the disassembly with 27 corresponding steps and provides details on cleaning, lubricating and installing each part in the proper orientation. Tools required include a driver and sealant.
Caterpillar Cat 318D2 L Excavator (Prefix XAH) Service Repair Manual (XAH0000...jfkskmmdmdm
This document provides instructions for disassembling and assembling the travel motor of a 318D2 L excavator. The disassembly process involves 27 steps to remove all individual components of the travel motor. Key steps include removing the head, brake piston, barrel assembly, shoe retainer and piston shoe assemblies. The assembly process reverses the disassembly with 27 corresponding steps and provides details on cleaning, lubricating and installing each part in the proper orientation. Tools required include a driver and seals must be installed with sealant applied to mating surfaces.
Caterpillar cat 318 d2 l excavator (prefix xah) service repair manual (xah000...fjskekdmjekm
This document provides instructions for disassembling and assembling the travel motor of a 318D2 L excavator. The disassembly process involves removing 27 different components from the travel motor in a specific sequence. The assembly process reverses the disassembly steps and provides additional warnings to ensure proper installation of components like the cam plate. Precise alignment of parts is critical for correct function of the travel motor.
Caterpillar Cat 315D L Excavator (Prefix JHA) Service Repair Manual (JHA00001...orrf0370383
The document provides step-by-step instructions for disassembling and assembling a travel motor. It begins by describing how to disassemble the travel motor by removing 27 different components and parts. These include removing the head, brake piston, barrel assembly, cam plate and more. It then describes the 25 steps to assemble the travel motor, putting in place components like the shaft assembly, piston guide, friction plates and more. Precise installation of seals, rings and alignment of parts is emphasized to prevent damage during reassembly.
Caterpillar Cat 315D L Excavator (Prefix JHA) Service Repair Manual Instant D...rishang96299
The document provides step-by-step instructions for disassembling and assembling a travel motor. It lists 27 steps for disassembly, which include removing components like the head, brake piston, barrel assembly, and shaft assembly. It then lists 26 steps for assembly, which describe cleaning components and installing them in reverse order, like pressing the shaft assembly into the body and installing the barrel assembly while keeping the cam plate engaged. Precautions are given to prevent damage and ensure correct alignment of parts.
Caterpillar Cat 315D L Excavator (Prefix JHA) Service Repair Manual Instant D...shanruliu7360
The document provides step-by-step instructions for disassembling and assembling a travel motor. It begins with disassembly, including removing 27 individual parts like the head, brake piston, barrel assembly, and shaft. The assembly section then lists 28 steps to reinstall these parts in reverse order, making sure components like the cam plate and piston shoe assemblies are correctly aligned. Special tools and precautions are noted to properly complete the process.
Caterpillar Cat 315D L Excavator (Prefix JHA) Service Repair Manual (JHA00001...jdksmmdmdd
The document provides step-by-step instructions for disassembling and assembling a travel motor. It begins with disassembly, including removing 27 individual parts like the head, brake piston, barrel assembly, and shaft. The assembly section then lists 28 steps to reinstall these parts in reverse order, making sure components like the cam plate and piston shoe assemblies are correctly positioned. Special tools and precautions are noted to ensure proper reassembly.
Caterpillar Cat 315D L Excavator (Prefix JHA) Service Repair Manual (JHA00001...dujkdksmdmdm
This document provides instructions for disassembling and assembling a travel motor. The disassembly process includes 27 steps to remove components like the head, brake piston, barrel assembly, shoe retainer, and shaft. The assembly section lists 28 steps to reinstall these components in the reverse order, noting that alignment marks and original locations must be followed to ensure proper reassembly. Precautions are provided to contain fluids, retain component identification, and install keys and pins correctly.
Caterpillar Cat 315D L Excavator (Prefix JHA) Service Repair Manual (JHA00001...fuusejkddmmd3e
The document provides step-by-step instructions for disassembling and assembling a travel motor. It begins with disassembly, including removing 27 individual parts like the head, brake piston, barrel assembly components, and shaft. The assembly section then lists 28 steps to reinstall these parts in reverse order, making sure components like the cam plate and piston shoe assemblies are correctly aligned. Special tools and precautions are noted to ensure proper reassembly.
Similar to Caterpillar cat 325 b l excavator (prefix 1hs) service repair manual (1hs00001 and up) (20)
Caterpillar cat 325 l track type excavator (prefix 9kl) service repair manual...f98soeodidkdk
This service repair manual provides instructions for disassembling and assembling the main control valve for 325, 325L, and 325N excavator models. It lists 33 detailed steps to fully disassemble the main control valve and its various components. Identification marks should be placed on parts as they are removed. Cleanliness and lubrication of internal parts is important during the process.
Caterpillar cat 325 c mobile hyd power unit (prefix msg) service repair manua...f98soeodidkdk
The document provides instructions for removing and installing a crankshaft gear on a 3126B engine. It lists the required tools and steps to remove the crankshaft first before removing the gear using a bearing puller. The installation procedure is not described.
Caterpillar cat 325 c ln excavator (prefix csj) service repair manual (csj000...f98soeodidkdk
This document provides instructions for disassembling and assembling the travel motor of 325C excavator models. The disassembly procedure involves 27 steps to remove components like the head, brake piston, barrel assembly, and shaft assembly. The assembly procedure describes 22 steps including installing seals, plates, springs and ensuring proper alignment of components like the cam plate and keys. Special care must be taken when handling components and aligning parts to prevent damage during reassembly.
Caterpillar cat 325 c ln excavator (prefix crb) service repair manual (crb000...f98soeodidkdk
The document provides instructions for removing and installing the camshaft on a Caterpillar 3126B engine used in 325C excavators. The summary is:
1) Remove the lifter group and front cover to access the camshaft. Wire the valve lifters away from the camshaft. Remove the camshaft retainer plate and bolts, then remove the camshaft.
2) Install the camshaft, ensuring the timing marks are aligned. Install the camshaft retainer plate and bolts. Install the lifter group and front cover.
3) The document provides step-by-step instructions for removing and installing the camshaft, camshaft gear
Caterpillar cat 325 c l excavator (prefix csj) service repair manual (csj0000...f98soeodidkdk
This document provides the disassembly and assembly procedures for a 325C excavator travel motor. The disassembly procedure involves 27 steps to remove all components from the travel motor body. The assembly procedure describes 22 steps to reinstall all components in the reverse order, ensuring proper installation of seals, plates, springs and other parts. Precise alignment marks and original component positions are critical to correctly reassemble the travel motor.
Caterpillar cat 325 c l excavator (prefix crb) service repair manual (crb0000...f98soeodidkdk
The document provides instructions for removing and installing various engine components on a 325C excavator, including:
1. Removing the camshaft by wiring the valve lifters away, removing retaining bolts, and lifting the camshaft out.
2. Installing the camshaft by carefully lowering it into place while ensuring proper timing marks are aligned.
3. Removing the camshaft bearings using a special tool, and installing new bearings while orienting the oil holes correctly.
Caterpillar cat 325 c excavator (prefix csj) service repair manual (csj00001 ...f98soeodidkdk
This document provides instructions for disassembling and assembling the travel motor of 325C excavator models. The disassembly procedure involves 27 steps to remove components like the head, brake piston, barrel assembly, springs and seals. The assembly procedure consists of 26 steps and requires applying sealant and hydraulic oil, and ensuring components like keys and locating pins are correctly installed. Special care must be taken to avoid damage and keep identification marks aligned during the process.
Caterpillar cat 325 c excavator (prefix crb) service repair manual (crb00001 ...f98soeodidkdk
The document provides instructions for removing and installing various engine components on a 325C excavator, including:
1. Removing the camshaft by wiring the valve lifters away, removing retaining bolts, and lifting the camshaft out.
2. Installing the camshaft by carefully inserting it into place while ensuring proper timing marks are aligned.
3. Removing the camshaft bearings using a special tool, and installing new bearings by orienting the oil holes and positioning joints.
Caterpillar cat 325 b ln excavator (prefix 8fn) service repair manual (8fn000...f98soeodidkdk
This document provides instructions for removing and servicing components of the rocker shaft and cylinder head on a 325B and 325B LN Excavator powered by a 3116 engine. The procedures include removing the rocker shaft assembly, disassembling the rocker shaft, inspecting components, assembling the rocker shaft, installing the rocker shaft and pushrods, and removing the cylinder head. Detailed steps are provided along with illustrations to guide the technician through the process while maintaining cleanliness and proper torque specifications.
Caterpillar cat 325 b ln excavator (prefix 6dn) service repair manual (6dn000...f98soeodidkdk
This document provides instructions for removing and installing inlet manifold components on a Caterpillar 325B excavator engine. The summary is:
1. Remove the valve mechanism cover and disconnect any attached pipes or solenoids from the inlet manifold.
2. Remove bolts securing the inlet manifold and remove the manifold and gasket.
3. To install the inlet manifold, position a new gasket and manifold on the engine and secure with bolts, reconnecting any pipes or solenoids.
Caterpillar cat 325 b l excavator (prefix 8rr) service repair manual (8rr0000...f98soeodidkdk
This document provides assembly instructions for the final drive of an excavator model 325B L. It describes:
1) Cleaning and preparing the final drive components and installing bearings in the main housing.
2) Determining the correct bearing preload and shim thickness to set the gear mesh.
3) Installing seals in the main housing and motor housing.
4) Assembling the carrier assemblies, installing gears, shafts, and retaining rings.
5) Positioning the main housing, gear, and ring gear on the motor housing and securing with bolts.
Caterpillar cat 325 b l excavator (prefix 6dn) service repair manual (6dn0000...f98soeodidkdk
This document provides instructions for removing and installing an inlet manifold on a Caterpillar 325B L excavator engine. It describes:
- Disconnecting air inlet piping and removing bolts to detach the manifold
- Installing a new gasket and reattaching the manifold using bolts torqued to 28 Nm
- Reconnecting any disconnected components at the end of the process
Caterpillar cat 325 b l excavator (prefix 2jr) service repair manual (2jr0000...f98soeodidkdk
This document provides instructions for installing pistons and connecting rods in a 3116 engine. It describes cleaning and lubricating parts, inserting piston rings into the cylinder bore using a compressor tool, installing each piston and connecting rod assembly by aligning it with the crankshaft, and torquing the connecting rod cap bolts. References are provided for determining whether pistons, connecting rods, pins, and bushings can be reused.
Caterpillar cat 325 b l excavator (prefix 1gs) service repair manual (1gs0000...f98soeodidkdk
The document provides disassembly and assembly instructions for the final drive of a 325B L excavator. It details 33 steps to disassemble the final drive components including removing carriers, gears, seals and bearings. It also outlines 28 steps for reassembling the final drive, including pressing in bearings, determining the correct shim thickness, installing seals and gears, and torquing bolts. Tools and torque specifications are provided. The purpose is to provide maintenance technicians with a procedure to fully disassemble and reassemble the excavator's final drive system.
Caterpillar cat 325 b excavator (prefix 8rr) service repair manual (8rr00001 ...f98soeodidkdk
This document provides assembly instructions for the final drive of an excavator model 325B L. It describes:
1) Cleaning and preparing the components, installing bearings in the main housing, and determining the correct shim thickness for the gear.
2) Installing seals in the main housing and motor housing.
3) Assembling the carrier assembly by installing planetary gears, shafts, and pins.
4) Positioning the main housing, gear, and ring gear on the motor housing and securing them with bolts.
Caterpillar cat 325 b excavator (prefix 8gm) service repair manual (8gm00001 ...f98soeodidkdk
This document provides instructions for disassembling and assembling the mechanical actuated fan on an excavator model 325B. It describes removing the fan blades, mounting hardware, oil, and performing a pressure test on the hub assembly. Further steps include removing the bellcrank, control shaft, hub assembly, through shaft, carrier/spool, main bearing, and rear seal. Detailed illustrations accompany each step to aid in failure analysis and repair.
Caterpillar cat 325 b excavator (prefix 8fn) service repair manual (8fn00001 ...f98soeodidkdk
This document provides instructions for removing and installing a cylinder head on an excavator. It begins by listing other components that must first be removed, such as the fuel filter base, governor, fuel linkage, and manifolds. The removal procedure then instructs technicians to attach a lifting device to the cylinder head and remove bolts holding it to the cylinder block before removing the gasket. The installation procedure lists cleaning the mating surfaces and applying lubricant to the gasket before positioning the head and torquing the bolts to specifications.
Caterpillar cat 325 b excavator (prefix 6dn) service repair manual (6dn00001 ...f98soeodidkdk
This document provides instructions for removing and installing an inlet manifold on a Caterpillar 325B L excavator engine. It describes:
- Disconnecting air inlet piping and removing bolts to detach the manifold
- Installing a new gasket and reattaching the manifold using bolts torqued to 28 Nm
- Reconnecting any disconnected components at the end of the process
Caterpillar cat 325 a l track type excavator (prefix 9 kl) service repair man...f98soeodidkdk
The document provides instructions for disassembling and assembling the main control valve for 325, 325L, and 325N excavators. It describes removing over 30 components of the valve including pressure control valves, check valves, relief valves, spools, housings, and covers. Detailed steps are provided for disassembling each component and removing seals, springs, plugs, and other parts. Similar instructions are given for reassembling the valve and installing all components back in their original locations with new seals and lubrication. Safety notices are included to properly secure parts when removing and to clean and inspect all components before reassembly.
Caterpillar cat 325 track type excavator (prefix 9 kl) service repair manual ...f98soeodidkdk
This service manual provides instructions for disassembling and assembling the main control valve for 325, 325L, and 325N excavator models. It details removing over 30 individual components of the valve including pressure control valves, check valves, relief valves, spools, seals and more. Dismantling and cleaning procedures are described along with proper reinstallation of all parts in their original locations and orientations.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325B L EXCAVATOR 1HS
Configuration: SUPPLEMENTARY SERVICE INFORMATION (DISASSEMBLY & ASSEMBLY) F 1HS00001-UP (MACHINE)
Disassembly and Assembly
325B Excavator Machine Systems
Media Number -SENR8963-06 Publication Date -01/02/2017 Date Updated -21/02/2017
i01219550
Travel Motor - Disassemble
SMCS - 4351-015
Disassembly Procedure
Start By:
a. Remove the travel motor.
Reference: Refer to Disassembly and Assembly, "Travel Motor - Remove" in this manual.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Thoroughly clean the outside of the travel motor prior to disassembly.
2. Fasten the travel motor to a suitable holding fixture in a vertical position. The weight of the
travel motor is 60 kg (132 lb).
1/8
SUPPLEMENTARY SERVICE INFORMATION (DISASSEMBLY & ASSEMBLY)...
2020/7/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. 3. Put an alignment mark across the head and the body of the travel motor for assembly
purposes. The head must be reinstalled in the head's original position on the body of the
travel motor.
Illustration 1 g00510326
Note: During the removal of head (2) from the body of the travel motor, be careful not to
scratch or damage the mating surfaces of the components.
4. Remove socket head bolts (1).
5. Remove head (2) from the body of the travel motor.
Illustration 2 g00510341
2/8
SUPPLEMENTARY SERVICE INFORMATION (DISASSEMBLY & ASSEMBLY)...
2020/7/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g00510349
6. Turn over head (2).
7. Remove O-ring seal (6), shims (5), port plate (4), and bearing (3) from the head.
8. Remove the two check valve assemblies from the head.
Note: There is a retainer under spring (9). This retainer is a press fit in head (2). Do not
remove the retainer.
9. Insert a dowel rod with a small diameter into hole (X). Tap the dowel rod with a plastic
hammer in order to remove spring (9), poppet (8) and seat (7) from the head.
Illustration 4 g00510351
10. Remove three fittings (10) and plugs (11) from the head. Remove the O-ring seal from each
fitting.
Illustration 5 g00510352
11. Remove three O-ring seals (12) and washer set (13) from the body of the travel motor.
12. Place a shop towel over brake piston (14). Retain brake piston (14) by hand, and apply
approximately 525 kPa (75 psi) of shop air pressure to brake release port (Y). Make sure
that the shop air pressure is free of water. Brake piston (14) will move up the piston guide,
and out of the piston guide. Remove brake piston (14) from the body of the travel motor.
3/8
SUPPLEMENTARY SERVICE INFORMATION (DISASSEMBLY & ASSEMBLY)...
2020/7/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 6 g00510353
13. Remove O-ring seal (15) from the brake piston. Remove backup ring (16) from the brake
piston.
14. Remove O-ring seal (17) from the brake piston. Remove backup ring (18) from the brake
piston.
Illustration 7 g00510356
15. Remove piston guide (19), five friction plates (20) and the four steel plates from the body of
the travel motor.
Illustration 8 g00510359
4/8
SUPPLEMENTARY SERVICE INFORMATION (DISASSEMBLY & ASSEMBLY)...
2020/7/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. 16. Remove O-ring seal (21) from the piston guide. Remove backup ring (22) from the piston
guide.
Illustration 9 g00510365
Note: Do not allow the components of barrel assembly (23) to come apart during the
removal from the travel motor. All of the components in the barrel assembly must be
reinstalled in the component's original location.
17. Use two large screwdrivers, as shown. Slowly remove barrel assembly (23) from the body
of the travel motor. Do not allow the components to fall apart.
Illustration 10 g00510502
Note: Shoe retainer (24) and piston shoe assemblies (25) are not serviced separately. Prior
to the removal of the shoe retainer and the piston shoe assemblies from barrel (26), put
identification marks on piston shoe assemblies (25) for assembly purposes. Identification
marks are used to identify the piston shoe assembly's location in shoe retainer (24) and
barrel (26). The piston shoe assemblies must be reinstalled in the piston shoe assembly's
original bores in the shoe retainer and the barrel.
18. Remove shoe retainer (24) and piston shoe assemblies (25) from barrel (26). Separate the
piston shoe assemblies from the shoe retainer.
5/8
SUPPLEMENTARY SERVICE INFORMATION (DISASSEMBLY & ASSEMBLY)...
2020/7/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 11 g00510504
19. Remove guide (27), spacer (28) and springs (29) from the barrel.
Illustration 12 g00510547
20. Remove cam plate (30) from the body of the travel motor.
Illustration 13 g00510550
21. Remove two keys (31) and the two locating pins (not shown) from the body of the travel
motor.
6/8
SUPPLEMENTARY SERVICE INFORMATION (DISASSEMBLY & ASSEMBLY)...
2020/7/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 14 g00510551
22. Remove O-ring seal (33) from the body of the travel motor.
23. Use a soft faced hammer to remove shaft assembly (34) from the body of the travel motor.
Remove the shaft assembly in the direction that is indicated by the arrow. Refer to
Illustration 14.
Illustration 15 g00510595
24. Remove retaining rings (35) from each side of bearing (36). Push shaft (34) out of bearing
(36) with a press.
Illustration 16 g00510598
7/8
SUPPLEMENTARY SERVICE INFORMATION (DISASSEMBLY & ASSEMBLY)...
2020/7/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 25. Remove inner race (37) from shaft (34).
Illustration 17 g00510599
26. Remove lip seal (38) from the body of the travel motor.
Illustration 18 g00510605
27. Remove two stoppers (39) and the two pistons from the body of the travel motor.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Jul 24 11:15:57 UTC+0800 2020
8/8
SUPPLEMENTARY SERVICE INFORMATION (DISASSEMBLY & ASSEMBLY)...
2020/7/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325B L EXCAVATOR 1HS
Configuration: SUPPLEMENTARY SERVICE INFORMATION (DISASSEMBLY & ASSEMBLY) F 1HS00001-UP (MACHINE)
Disassembly and Assembly
325B Excavator Machine Systems
Media Number -SENR8963-06 Publication Date -01/02/2017 Date Updated -21/02/2017
i01706705
Travel Motor - Assemble
SMCS - 4351-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Gp 1
1. Make sure that all of the components of the travel motor are thoroughly clean and free of
dirt and debris prior to assembly.
Illustration 1 g00510595
2. Install retaining ring (35) in the groove on shaft (34).
3. Install bearing (36) on shaft (34) with a press. Install the bearing until the bearing contacts
the retaining ring.
1/10
SUPPLEMENTARY SERVICE INFORMATION (DISASSEMBLY & ASSEMBLY)...
2020/7/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. 4. Install the other retaining ring on the opposite side of bearing (36).
Illustration 2 g00510598
5. Install inner race (37) on the end of shaft (34) until the inner race is seated against the
shoulder on the shaft.
Illustration 3 g00651891
(a) Body
6. Apply a thin coat of 5P-3413 Pipe Sealant on Surfaces (Y) of the body of the travel motor.
7. Use Tooling (A) in order to install lip seal (38).
8. Install lip type seal (38) in the body of the travel motor. Install the lip seal so that the sealing
lip is facing in the direction that is shown. Make sure that the lip seal contacts the
counterbore in the body of the travel motor.
Note: Slowly rotate shaft assembly (34) during the installation in order to make sure that the
shaft assembly does not bind in the body of the travel motor.
9. Apply clean hydraulic oil on the lip of lip seal (38).
2/10
SUPPLEMENTARY SERVICE INFORMATION (DISASSEMBLY & ASSEMBLY)...
2020/7/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. 10. Use a press to install shaft assembly (34) in the body of the travel motor. Slowly rotate the
shaft during the installation in order to make sure that the shaft does not bind. Make sure
that the bearing on the shaft contacts the counterbore in the body of the travel motor.
Illustration 4 g00651960
NOTICE
The locating pin on each key is not centered. In order to prevent
damage to the barrel assembly during assembly of the travel motor, the
keys must be installed as shown. Also, the keys must be installed in the
key's original location in the body of the travel motor.
11. Install the two locating pins and two keys (31) in the body of the travel motor, as shown.
Illustration 5 g00510547
3/10
SUPPLEMENTARY SERVICE INFORMATION (DISASSEMBLY & ASSEMBLY)...
2020/7/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. 12. Install cam plate (30) in the body of the travel motor in the cam plate's original location.
Make sure that the two pistons and two keys (31) in the body of the travel motor engage
properly with the cam plate.
Illustration 6 g00510504
13. Install nine springs (29) in the barrel. Install spacer (28) and guide (27) on the barrel.
Illustration 7 g00878253
14. Install piston shoe assemblies (25) in the piston shoe assembly's original bores in shoe
retainer (24).
15. Apply clean hydraulic oil in the bores of the barrel and on piston shoe assemblies (25).
Install the piston shoe assemblies with the shoe retainer in the piston shoe assembly's
original bore in barrel (26).
NOTICE
Make sure that the cam plate is correctly engaged with the two pistons
in the body of the travel motor prior to installing the barrel assembly.
When the body of the travel motor is tilted to allow the installation of
the barrel assembly, the cam plate can slide off of the two pistons. The
remaining parts of the travel motor can be assembled with the cam
plate in the incorrect position.
4/10
SUPPLEMENTARY SERVICE INFORMATION (DISASSEMBLY & ASSEMBLY)...
2020/7/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Extensive damage will result from the incorrect installation of the cam
plate. Follow the exact installation procedure to prevent damage.
16. Apply clean hydraulic oil on the sliding surfaces of the cam plate, on the piston shoe
assemblies and on the splined shaft of the travel motor.
Illustration 8 g00485953
17. Route a piece of strong string through an opening for the cam plate tension adjusters. Route
the string over the sliding surface of cam plate (30) and through the opposite opening for the
cam plate tension adjusters. Hold the string taut in order to keep cam plate (30) correctly
engaged with keys (31). Keep the string taut and position the body of the travel motor on the
body's side. Do not release the tension on the string at this time. Install barrel assembly (23)
as a unit on the shaft. Pull the string out of the body of the travel motor. It may be necessary
to pull the barrel assembly and the piston shoe assemblies away from the cam plate slightly
in order to release the string.
Illustration 9 g00651967
5/10
SUPPLEMENTARY SERVICE INFORMATION (DISASSEMBLY & ASSEMBLY)...
2020/7/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. 18. Install O-ring seal (21) and backup ring (22) on piston guide (19), as shown.
Illustration 10 g00510356
19. Place the body of the travel motor in a vertical position.
20. Apply clean hydraulic oil on five friction plates (20) and the four steel plates. Install the
plates in alternating order in the body of the travel motor. Start with a friction plate and end
with a friction plate.
21. Install piston guide (19) in the body of the travel motor until the piston guide contacts the
counterbore in the body of the travel motor.
Illustration 11 g00878297
Note: Make sure that brake piston (14) is thoroughly clean and free of dirt and debris.
22. Install O-ring seal (16). Install backup ring (15).
23. Install O-ring seal (17). Install backup ring (18).
6/10
SUPPLEMENTARY SERVICE INFORMATION (DISASSEMBLY & ASSEMBLY)...
2020/7/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. 24. Apply a thin coat of hydraulic oil on the surfaces of piston (14) which contact the body of
the travel motor. Install piston (14) in the body of the travel motor by hand. It may be
necessary to use a soft faced hammer to seat the piston correctly.
Illustration 12 g00878299
Illustration 13 g00878239
25. Install washer set (12) in piston (14), as shown.
26. Install O-ring seals (13) in the body of the travel motor, as shown.
7/10
SUPPLEMENTARY SERVICE INFORMATION (DISASSEMBLY & ASSEMBLY)...
2020/7/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 14 g00510605
27. Install the two pistons and two stoppers (39) in the housing of the travel motor. Tighten the
stoppers to a torque of 140 ± 14 N·m (105 ± 10 lb ft).
Illustration 15 g00510351
28. Install the O-ring seals on fittings (10). Apply 5P-3413 Pipe Sealant on the threads of
fittings (10). Install the fittings in the head, as shown.
29. Install plugs (11) in the head. Tighten each plug to a torque of 15 ± 2 N·m (11 ± 1 lb ft).
Illustration 16 g00510349
8/10
SUPPLEMENTARY SERVICE INFORMATION (DISASSEMBLY & ASSEMBLY)...
2020/7/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 17 g00510341
30. Apply a thin coat of 9S-3263 Thread Lock Compound on the threads of the two check
valves. Install the check valves in the head.
31. Install seat (7), poppet (8) and spring (9) in the head at Location (X).
32. Install O-ring seal (6) in the head, as shown.
33. Install bearing (3) in the head until the bearing contacts the counterbore in the cover.
34. Apply 1U-6396 O-Ring Assembly Compound on port plate (4). Install the port plate in the
port plate's original position on the motor cover.
35. Use a shim or shims (5) so that the following requirements are met.
Note: During the following checks, turn the travel motor output shaft in a clockwise
direction.
a. The travel motor output shaft does not rotate with an applied torque of 440 N·m
(325 lb ft) or more with the parking brake release port open.
b. The travel motor output shaft rotates with an applied torque of 29 N·m (21 lb ft) or
less when the parking brake release port is pressurized to 780 kPa (115 psi) with both
the inlet port and the outlet port open to the hydraulic oil tank.
Note: It may be necessary to remove head (2) several times in order to determine the correct
thickness of shim or shims (5) that are used to adjust the rolling torque of the travel motor
output shaft.
36. Apply a thin layer of 5P-0960 Molybdenum Grease on shim or shims (5). Install the shim or
shims on the head. The grease will hold the shim or shims in place during the installation of
the head. Install the head on the body of the travel motor.
9/10
SUPPLEMENTARY SERVICE INFORMATION (DISASSEMBLY & ASSEMBLY)...
2020/7/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 18 g00510326
37. Place head (2) in the head's original position on the travel motor. Install socket head bolts
(1) that secure the head. Tighten the socket head bolts to a torque of 175 ± 18 N·m
(130 ± 13 lb ft).
NOTICE
To prevent possible damage to the travel motor, fill the unit with oil at
least to the fill port before operating the machine. Refer to the
Operation and Maintenance Manual for the correct oil specification.
End By:
a. Install the travel motor. Refer to Disassembly and Assembly, "Travel Motor - Install" in this
manual.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Jul 24 11:16:52 UTC+0800 2020
10/10
SUPPLEMENTARY SERVICE INFORMATION (DISASSEMBLY & ASSEMBL...
2020/7/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325B L EXCAVATOR 1HS
Configuration: SUPPLEMENTARY SERVICE INFORMATION (DISASSEMBLY & ASSEMBLY) F 1HS00001-UP (MACHINE)
Disassembly and Assembly
325B Excavator Machine Systems
Media Number -SENR8963-06 Publication Date -01/02/2017 Date Updated -21/02/2017
i03524320
Travel Motor - Install
SMCS - 4351-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-7692 Threaded Rod M16 by 381mm 2
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Thoroughly clean the mating surfaces of the travel motor and the final drive.
1/3
SUPPLEMENTARY SERVICE INFORMATION (DISASSEMBLY & ASSEMBLY)...
2020/7/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 1 g00651795
2. Install a new O-ring seal (5) . Apply clean hydraulic oil on O-ring seal (5) .
Illustration 2 g00707267
3. Attach a suitable lifting device to travel motor (4) , as shown. The weight of travel motor (4)
is approximately 57 kg (125 lb).
Illustration 3 g00944825
2/3
SUPPLEMENTARY SERVICE INFORMATION (DISASSEMBLY & ASSEMBLY)...
2020/7/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. 4. Carefully install travel motor (4) on Tooling (A) . Slide travel motor (4) into the final drive.
5. Install bolt (2A) that secures travel motor (4) to the final drive.
6. Remove Tooling (A) .
Illustration 4 g00707275
Typical example
7. Install bolts (2) .
8. Connect hose assemblies (3) and (1) .
9. Fill the final drive with oil. Refer to Operation and Maintenance Manual, "Lubricant
Viscosities" for the proper oil viscosity. Refer to Operation and Maintenance Manual, "Final
Drive Oil Level - Check" for the correct filling procedure.
10. Install high efficiency filters in place of the pilot filter, the case drain filter, and the return
filter.
Note: High efficiency filters should not be run for more than 250 hours before you change
back to the standard filters.
11. Obtain a hydraulic oil sample from the main S·O·S port. Refer to Operation and
Maintenance Manual, "Sampling Interval and Location of Sampling Valve" for the correct
location.
12. If the S·O·S sample exceeds ISO 18/15, flush the hydraulic system. Refer to Contamination
Control Guideline, SEBF8447 for further information.
End By: Install the counterbalance valve. Refer to Disassembly and Assembly, "Counterbalance
Valve (Travel) - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Jul 24 11:17:48 UTC+0800 2020
3/3
SUPPLEMENTARY SERVICE INFORMATION (DISASSEMBLY & ASSEMBLY)...
2020/7/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325B L EXCAVATOR 1HS
Configuration: SUPPLEMENTARY SERVICE INFORMATION (DISASSEMBLY & ASSEMBLY) F 1HS00001-UP (MACHINE)
Disassembly and Assembly
325B Excavator Machine Systems
Media Number -SENR8963-06 Publication Date -01/02/2017 Date Updated -21/02/2017
i00999156
Final Drive - Remove
SMCS - 4050-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
(A) 138-7574 Link Bracket 2
Start By:
a. Separate the track assembly. Refer to Disassembly and Assembly, "Track - Seperate" in this
manual.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
1/4
SUPPLEMENTARY SERVICE INFORMATION (DISASSEMBLY & ASSEMBLY)...
2020/7/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. At operating temperature, the hydraulic oil is hot and under pressure.
Hot oils can cause burns.
To prevent possible personal injury, release the pressure in the work
tool hydraulic circuit (boom, stick, bucket, and swing), travel circuits,
and the hydraulic oil tank at the filler cap before any hydraulic lines or
components are disconnected or removed.
Remove the filler cap only when the engine is stopped and the filler cap
is cool enough to touch.
1. Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic
System Pressure - Release" in this manual.
Illustration 1 g00486980
2. Remove four bolts (1) and the washers that secure cover assembly (2). Remove cover
assembly (2) from the inside rear of the undercarriage frame assembly.
Illustration 2 g00486981
2/4
SUPPLEMENTARY SERVICE INFORMATION (DISASSEMBLY & ASSEMBLY)...
2020/7/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
26. Note: When two tube assemblies (3) are disconnected from the travel brake valve, oil will
flow from the tube assemblies. Oil will also flow from two hose assemblies (4) and (5)
when the hose assemblies are disconnected from the travel motor. Place a suitable container
under the tube assemblies and under the hose assemblies in order to collect the oil.
3. Disconnect two tube assemblies (3) from the travel brake valve. Disconnect hose assemblies
(4) and (5) from the travel motor. Put plugs in the ends of the tube assemblies and in the
ends of the hose assemblies in order to prevent oil loss and keep contaminants out of the
hydraulic system.
4. Remove elbow (6) from the travel motor.
Illustration 3 g00486987
5. Fasten Tooling (A) and a hoist to final drive (7), as shown. Put a slight lifting tension on the
final drive.
Illustration 4 g00486988
6. Remove two plugs (9) from the forcing bolt holes in the undercarriage frame assembly.
7. Remove 20 bolts (8) and the washers that secure the final drive to the undercarriage frame
assembly.
3/4
SUPPLEMENTARY SERVICE INFORMATION (DISASSEMBLY & ASSEMBLY)...
2020/7/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 5 g00486990
8. Install two suitable sized forcing bolts (10) in the forcing bolt holes in the frame. Tighten
the two forcing bolts evenly in order to loosen the final drive from the undercarriage frame
assembly.
9. Carefully remove final drive (7) from the undercarriage frame assembly. The combined
weight of the final drive and the travel motor is approximately 449 kg (990 lb).
10. Remove two forcing bolts (10) from the undercarriage frame assembly.
11. Remove the travel motor from the final drive. Refer to Disassembly and Assembly, "Travel
Motor - Remove" in this manual.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Jul 24 11:18:44 UTC+0800 2020
4/4
SUPPLEMENTARY SERVICE INFORMATION (DISASSEMBLY & ASSEMBLY)...
2020/7/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325B L EXCAVATOR 1HS
Configuration: SUPPLEMENTARY SERVICE INFORMATION (DISASSEMBLY & ASSEMBLY) F 1HS00001-UP (MACHINE)
Disassembly and Assembly
325B Excavator Machine Systems
Media Number -SENR8963-06 Publication Date -01/02/2017 Date Updated -21/02/2017
i02202099
Final Drive - Disassemble
SMCS - 4050-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 138-7573 Link Bracket 2
C 1P-1860 Retaining Ring Pliers 1
D
6B-6682 Full Nut 1
1P-5546 Crossblock 1
5P-8248 Hard Washer 4
6V-3142 Puller Plate 1
(1)
Threaded Rod 1
(2)
Spacer 4
E 138-7574 Link Bracket 2
F
8B-7561 Step Plate 1
5F-7465 Puller Assembly 1
1H-3107 Bearing Puller Assembly 1
1H-3112 Bearing Puller Assembly 1
1P-5551 Screw Assembly 1
1/11
SUPPLEMENTARY SERVICE INFORMATION (DISASSEMBLY & ASSEMBLY)...
2020/7/24
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...