The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 Compact Track Loader, including:
- Flywheel installation which requires cleaning surfaces, heating the ring gear, and torquing bolts to a specified value.
- Crankshaft rear seal replacement involving removing the old seal and pressing in a new one using specific tools.
- Removing and installing the flywheel housing which requires attaching lifting equipment and torquing bolts to a specified value.
- Procedures for the crankshaft pulley, front seal, and bearing case cover that include cleaning, applying oil, and ensuring proper orientation of parts.
The document provides instructions for removing and installing a fuel injection pump on a Caterpillar C3.8 engine. It outlines 8 steps to remove the pump, including disconnecting fuel lines, removing mounting nuts, and using a gear puller. It then describes 5 steps to install the pump, including connecting fuel lines, tightening mounting nuts, and aligning gears. Safety precautions are provided to relieve fuel pressure before opening lines.
Caterpillar cat 289 d compact track loader (prefix a9z) service repair manual...ujfjdkkmsme
This document provides instructions for removing and installing various engine components on a Caterpillar 289D compact track loader with a C3.3B engine. It describes removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures provide illustrations and specify required tools and torque specifications where applicable. The document aims to guide maintenance and repair of these engine components.
Caterpillar cat 950 f wheel loader (prefix 4dj) service repair manual (4dj000...ifkkdmdmdm
This document provides step-by-step instructions for disassembling the transmission of a 950F Wheel Loader model. It lists 79 steps to remove various transmission components including the torque converter, transmission control valve, carrier assemblies, planetary gears, clutches, seals, and housing components. Detailed diagrams accompany each step to illustrate the proper procedure and required tooling.
Jcb 8035 z mini excavator service repair manual sn 1230500 onwardsjkmsedopl
This document provides information about identifying machines, standard torque settings for fasteners, and service tools for a JCB 8025Z, 8030Z, and 8035Z service manual. It identifies the machine models and serial numbers covered by the manual. It also outlines the section numbering format and units of measurement used. Tables are included that list standard torque settings for UNF and metric grade fasteners under different conditions. Identification plates and numbers on the machine are described. A list of service tools and consumables is also referenced for different sections of the manual.
Caterpillar cat 938 g wheel loader (prefix 8rs) service repair manual (8rs006...fusefjjskekemm
This document provides instructions for removing and installing a cylinder head on a Caterpillar 3126 engine. The removal process involves detaching several engine components before removing the cylinder head bolts and lifting the cylinder head off. The installation process specifies cleaning the mating surfaces, installing a new cylinder head gasket, positioning the cylinder head, inspecting and lubricating the cylinder head bolts, and tightening the bolts in a specific sequence according to the provided torques.
Caterpillar cat 305 e2 cr mini hydraulic excavator (prefix df5) service repai...fikskkdmmd1
The document provides instructions for removing and installing various components of a 305E2 CR Mini Hydraulic Excavator engine, including the fuel injection lines, exhaust gas recirculation cooler, fuel injection pump, electronic unit injector, and turbocharger. Safety precautions are outlined that must be followed when working on fuel system and high temperature components.
The document provides instructions for removing and installing a fuel injection pump on a Caterpillar C3.8 engine. It outlines 8 steps to remove the pump, including disconnecting fuel lines, removing mounting nuts, and using a gear puller. It then describes 5 steps to install the pump, including connecting fuel lines, tightening mounting nuts, and aligning gears. Safety precautions are provided to relieve fuel pressure before opening lines.
Caterpillar cat 289 d compact track loader (prefix a9z) service repair manual...ujfjdkkmsme
This document provides instructions for removing and installing various engine components on a Caterpillar 289D compact track loader with a C3.3B engine. It describes removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures provide illustrations and specify required tools and torque specifications where applicable. The document aims to guide maintenance and repair of these engine components.
Caterpillar cat 950 f wheel loader (prefix 4dj) service repair manual (4dj000...ifkkdmdmdm
This document provides step-by-step instructions for disassembling the transmission of a 950F Wheel Loader model. It lists 79 steps to remove various transmission components including the torque converter, transmission control valve, carrier assemblies, planetary gears, clutches, seals, and housing components. Detailed diagrams accompany each step to illustrate the proper procedure and required tooling.
Jcb 8035 z mini excavator service repair manual sn 1230500 onwardsjkmsedopl
This document provides information about identifying machines, standard torque settings for fasteners, and service tools for a JCB 8025Z, 8030Z, and 8035Z service manual. It identifies the machine models and serial numbers covered by the manual. It also outlines the section numbering format and units of measurement used. Tables are included that list standard torque settings for UNF and metric grade fasteners under different conditions. Identification plates and numbers on the machine are described. A list of service tools and consumables is also referenced for different sections of the manual.
Caterpillar cat 938 g wheel loader (prefix 8rs) service repair manual (8rs006...fusefjjskekemm
This document provides instructions for removing and installing a cylinder head on a Caterpillar 3126 engine. The removal process involves detaching several engine components before removing the cylinder head bolts and lifting the cylinder head off. The installation process specifies cleaning the mating surfaces, installing a new cylinder head gasket, positioning the cylinder head, inspecting and lubricating the cylinder head bolts, and tightening the bolts in a specific sequence according to the provided torques.
Caterpillar cat 305 e2 cr mini hydraulic excavator (prefix df5) service repai...fikskkdmmd1
The document provides instructions for removing and installing various components of a 305E2 CR Mini Hydraulic Excavator engine, including the fuel injection lines, exhaust gas recirculation cooler, fuel injection pump, electronic unit injector, and turbocharger. Safety precautions are outlined that must be followed when working on fuel system and high temperature components.
Valeo Transmission Systems Clutch SAT-HEC valeoscope product focus 998121Hugo Vallet
Valeo Transmission Systems’ mission is to be the supplier of choice for all powertrain architectures with innovative technologies developed for efficient and comfortable power transfer from the engine to the transmission, whilst reducing fuel consumption.
• Find Valeo clutch offer on spare parts on http://www.valeoservice.com
Discover other valeoscope brochures:
• Air Conditioning: http://www.slideshare.net/ValeoService/valeo-air-conditioning-valeoscope-technical-brochure-ac-handbook-part-1-998321
• Clutch KIT4P conversion kits: http://www.slideshare.net/ValeoService/valeo-transmission-systems-clutch-kit4p-valeoscope-technical-handbook-998100
• Clutch hydraulics CSC, CMC & CRC: http://slideshare.net/ValeoService/valeo-transmission-systems-clutch-hydraulics-valeoscope-product-focus-998123
• Dual-Mass flywheel technology: http://www.slideshare.net/ValeoService/valeo-transmission-systems-dualmass-flywheel-valeoscope-product-focus-998120
• Lighting System technologies: http://www.slideshare.net/ValeoService/valeo-lighting-systems-from-light-to-advanced-vision-technologies-valeoscope-technical-handbook-998542
• Truck brake pad diag & fit: http://www.slideshare.net/ValeoService/truck-brake-pad-fault-assessment-valeoscope-diagfit-brochure-957100
Valeo, automotive technology, naturally.
• Follow Valeo on facebook : http://www.facebook.com/Valeo.Group
The document contains a CNC program for machining multiple contours on a workpiece using two different tools. The program includes code for setting tool offsets, selecting tools, and machining various profiles including squares, triangles, and open pockets using linear and circular interpolation moves. It also provides alternative code for one of the contour machining sections and includes diagrams of the different features to be cut.
Jcb 8030 z mini excavator service repair manual sn 1228500 onwardsjkmsedopl
This document provides information about identifying JCB machines, including identification plates, product identification numbers, engine identification numbers, and ROPS/TOPS/FOGS labels. It discusses the data plate attached to the front of the machine, which contains the product identification number and serial number. It also describes identifying information found on engine identification plates, including the engine type, build list, country of manufacture, serial number, and year of manufacture. The summary advises being careful when modifying or repairing ROPS, TOPS, and FOGS structures, as improper repairs can compromise safety.
Jcb 8030 zts compact excavator service repair manual sn 1228500dujjsjfkksekm
This document provides information about identifying JCB machines, standard torque settings for fasteners, and service tools and consumables. It discusses identification plates, product identification numbers, engine identification numbers, and ROPS/TOPS certification labels. It also includes tables listing torque settings for UNF and metric grade fasteners under lubricated and unlubricated conditions. Finally, it provides a numerical list and details of common service tools as well as sealing and retaining compounds used in repairs.
This document contains a list of students in various classes (8a through 8g) with their student ID numbers and names. For each class, it provides a numbered list of the students with their ID number and full name. There are around 40 students listed in each class for a total of over 500 students named across the 7 class lists.
This document is a price list for spare parts from a company that sells auto parts. It contains over 100 part names and descriptions organized by engine and transmission components. The parts include items for the cylinder head, camshaft, crankshaft, pistons, manifolds, and other engine systems. Each part lists the corresponding part code, name in Chinese and English, description, and catalogue number.
Massey ferguson mf65 tractor service parts catalogue manual (part number 819...fjsekkdkmem
This document provides part numbers and descriptions for components of Massey Ferguson MF 65/765 tractor cylinder blocks, cylinder heads, and crankshafts. It includes over 100 items such as cylinder block components, cylinder head valves, springs, plates and gaskets, as well as crankshaft bearings, connecting rods, pistons, rings, and flywheels. Notes are provided to indicate use of earlier or later part numbers depending on the tractor serial or engine number.
Caterpillar cat 120 h motor grader (prefix 2an) service repair manual (2an000...fjskeksmemmer
This document provides instructions for removing and installing various components related to the drive train of a Caterpillar 120H motor grader, including the brake and wheel spindle housings, differential drive shaft, and parking brake. It describes disconnecting air and hydraulic lines, draining fluids, and removing guards, bolts, and other hardware to access the internal components. Detailed steps are provided for removing each part and installing replacement components, with notes about weight, torque specifications, and precautions regarding hot fluids or pressurized air.
This document is a parts catalogue for a Yamaha T135 motorcycle. It includes part numbers, descriptions and other details for engine, chassis and other systems parts. The document contains sections for the cylinder head, crankshaft, valves, camshaft, water pump, radiator, and other major component groups. Diagrams and part lists are provided to help identify replacement parts.
Caterpillar cat 950 f series ii wheel loader (prefix 4dj) service repair manu...ifkkdmdmdm
This document provides instructions for removing and installing a governor and fuel injection control linkage on a Caterpillar 950F wheel loader. The summary is:
1. The removal procedure details disconnecting tubes, removing clips and bolts, and using special tools to remove the governor and control linkage.
2. Cleaning and lubricating new seals is emphasized before installing replacement parts.
3. The installation procedure specifies using tools to replace clips and pins and adjusts settings before reconnecting tubes. Proper lubrication of seals during reassembly is stressed.
The document provides instructions for removing and installing various engine components on a Caterpillar C3.8 engine, including:
- Installing the flywheel, ensuring the ring gear is oriented correctly
- Removing and installing the crankshaft rear seal and carrier
- Removing and installing the flywheel housing
- Removing and installing the crankshaft pulley
The procedures include lists of required tools and step-by-step instructions accompanied by illustrations. Safety and installation notes are also provided.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 compact track loader. It describes how to install the flywheel, including cleaning and heating the ring gear. It also details removing and installing the crankshaft rear seal, crankshaft rear seal carrier, flywheel housing, crankshaft pulley, and crankshaft front seal. Tools required are listed for each procedure.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 compact track loader. It includes procedures for installing the flywheel, removing and installing the crankshaft rear seal and carrier, removing and installing the flywheel housing, removing and installing the crankshaft pulley, and removing and installing the crankshaft front seal. The procedures provide illustrations and specify any required tools.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 compact track loader. It includes procedures for installing the flywheel, removing and installing the crankshaft rear seal and carrier, removing and installing the flywheel housing, removing and installing the crankshaft pulley, and removing and installing the crankshaft front seal. The procedures provide illustrations and specify any required tools.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 compact track loader. It includes procedures for installing the flywheel, removing and installing the crankshaft rear seal and carrier, removing and installing the flywheel housing, removing and installing the crankshaft pulley, and removing and installing the crankshaft front seal. The procedures provide illustrations and specify any required tools.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 compact track loader. It describes how to install the flywheel, including cleaning and heating the ring gear. It also details removing and installing the crankshaft rear seal, crankshaft rear seal carrier, flywheel housing, crankshaft pulley, and crankshaft front seal. Tools required are listed for each procedure.
The document provides instructions for removing and installing various engine components on a Caterpillar C3.8 engine, including:
- Installing the flywheel, ensuring the ring gear is oriented correctly
- Removing and installing the crankshaft rear seal and carrier
- Removing and installing the flywheel housing
- Removing and installing the crankshaft pulley
The procedures include lists of required tools and step-by-step instructions with accompanying illustrations. Safety and installation notes are provided throughout.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 compact track loader. It includes procedures for installing the flywheel, removing and installing the crankshaft rear seal and carrier, removing and installing the flywheel housing, removing and installing the crankshaft pulley, and removing and installing the crankshaft front seal. The procedures provide illustrations and specify any required tools.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 compact track loader. It describes how to install the flywheel, including cleaning and heating the ring gear. It also details removing and installing the crankshaft rear seal, crankshaft rear seal carrier, flywheel housing, crankshaft pulley, and crankshaft front seal. The procedures note any required tools and provide illustrations to support the step-by-step instructions.
Valeo Transmission Systems Clutch SAT-HEC valeoscope product focus 998121Hugo Vallet
Valeo Transmission Systems’ mission is to be the supplier of choice for all powertrain architectures with innovative technologies developed for efficient and comfortable power transfer from the engine to the transmission, whilst reducing fuel consumption.
• Find Valeo clutch offer on spare parts on http://www.valeoservice.com
Discover other valeoscope brochures:
• Air Conditioning: http://www.slideshare.net/ValeoService/valeo-air-conditioning-valeoscope-technical-brochure-ac-handbook-part-1-998321
• Clutch KIT4P conversion kits: http://www.slideshare.net/ValeoService/valeo-transmission-systems-clutch-kit4p-valeoscope-technical-handbook-998100
• Clutch hydraulics CSC, CMC & CRC: http://slideshare.net/ValeoService/valeo-transmission-systems-clutch-hydraulics-valeoscope-product-focus-998123
• Dual-Mass flywheel technology: http://www.slideshare.net/ValeoService/valeo-transmission-systems-dualmass-flywheel-valeoscope-product-focus-998120
• Lighting System technologies: http://www.slideshare.net/ValeoService/valeo-lighting-systems-from-light-to-advanced-vision-technologies-valeoscope-technical-handbook-998542
• Truck brake pad diag & fit: http://www.slideshare.net/ValeoService/truck-brake-pad-fault-assessment-valeoscope-diagfit-brochure-957100
Valeo, automotive technology, naturally.
• Follow Valeo on facebook : http://www.facebook.com/Valeo.Group
The document contains a CNC program for machining multiple contours on a workpiece using two different tools. The program includes code for setting tool offsets, selecting tools, and machining various profiles including squares, triangles, and open pockets using linear and circular interpolation moves. It also provides alternative code for one of the contour machining sections and includes diagrams of the different features to be cut.
Jcb 8030 z mini excavator service repair manual sn 1228500 onwardsjkmsedopl
This document provides information about identifying JCB machines, including identification plates, product identification numbers, engine identification numbers, and ROPS/TOPS/FOGS labels. It discusses the data plate attached to the front of the machine, which contains the product identification number and serial number. It also describes identifying information found on engine identification plates, including the engine type, build list, country of manufacture, serial number, and year of manufacture. The summary advises being careful when modifying or repairing ROPS, TOPS, and FOGS structures, as improper repairs can compromise safety.
Jcb 8030 zts compact excavator service repair manual sn 1228500dujjsjfkksekm
This document provides information about identifying JCB machines, standard torque settings for fasteners, and service tools and consumables. It discusses identification plates, product identification numbers, engine identification numbers, and ROPS/TOPS certification labels. It also includes tables listing torque settings for UNF and metric grade fasteners under lubricated and unlubricated conditions. Finally, it provides a numerical list and details of common service tools as well as sealing and retaining compounds used in repairs.
This document contains a list of students in various classes (8a through 8g) with their student ID numbers and names. For each class, it provides a numbered list of the students with their ID number and full name. There are around 40 students listed in each class for a total of over 500 students named across the 7 class lists.
This document is a price list for spare parts from a company that sells auto parts. It contains over 100 part names and descriptions organized by engine and transmission components. The parts include items for the cylinder head, camshaft, crankshaft, pistons, manifolds, and other engine systems. Each part lists the corresponding part code, name in Chinese and English, description, and catalogue number.
Massey ferguson mf65 tractor service parts catalogue manual (part number 819...fjsekkdkmem
This document provides part numbers and descriptions for components of Massey Ferguson MF 65/765 tractor cylinder blocks, cylinder heads, and crankshafts. It includes over 100 items such as cylinder block components, cylinder head valves, springs, plates and gaskets, as well as crankshaft bearings, connecting rods, pistons, rings, and flywheels. Notes are provided to indicate use of earlier or later part numbers depending on the tractor serial or engine number.
Caterpillar cat 120 h motor grader (prefix 2an) service repair manual (2an000...fjskeksmemmer
This document provides instructions for removing and installing various components related to the drive train of a Caterpillar 120H motor grader, including the brake and wheel spindle housings, differential drive shaft, and parking brake. It describes disconnecting air and hydraulic lines, draining fluids, and removing guards, bolts, and other hardware to access the internal components. Detailed steps are provided for removing each part and installing replacement components, with notes about weight, torque specifications, and precautions regarding hot fluids or pressurized air.
This document is a parts catalogue for a Yamaha T135 motorcycle. It includes part numbers, descriptions and other details for engine, chassis and other systems parts. The document contains sections for the cylinder head, crankshaft, valves, camshaft, water pump, radiator, and other major component groups. Diagrams and part lists are provided to help identify replacement parts.
Caterpillar cat 950 f series ii wheel loader (prefix 4dj) service repair manu...ifkkdmdmdm
This document provides instructions for removing and installing a governor and fuel injection control linkage on a Caterpillar 950F wheel loader. The summary is:
1. The removal procedure details disconnecting tubes, removing clips and bolts, and using special tools to remove the governor and control linkage.
2. Cleaning and lubricating new seals is emphasized before installing replacement parts.
3. The installation procedure specifies using tools to replace clips and pins and adjusts settings before reconnecting tubes. Proper lubrication of seals during reassembly is stressed.
The document provides instructions for removing and installing various engine components on a Caterpillar C3.8 engine, including:
- Installing the flywheel, ensuring the ring gear is oriented correctly
- Removing and installing the crankshaft rear seal and carrier
- Removing and installing the flywheel housing
- Removing and installing the crankshaft pulley
The procedures include lists of required tools and step-by-step instructions accompanied by illustrations. Safety and installation notes are also provided.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 compact track loader. It describes how to install the flywheel, including cleaning and heating the ring gear. It also details removing and installing the crankshaft rear seal, crankshaft rear seal carrier, flywheel housing, crankshaft pulley, and crankshaft front seal. Tools required are listed for each procedure.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 compact track loader. It includes procedures for installing the flywheel, removing and installing the crankshaft rear seal and carrier, removing and installing the flywheel housing, removing and installing the crankshaft pulley, and removing and installing the crankshaft front seal. The procedures provide illustrations and specify any required tools.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 compact track loader. It includes procedures for installing the flywheel, removing and installing the crankshaft rear seal and carrier, removing and installing the flywheel housing, removing and installing the crankshaft pulley, and removing and installing the crankshaft front seal. The procedures provide illustrations and specify any required tools.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 compact track loader. It includes procedures for installing the flywheel, removing and installing the crankshaft rear seal and carrier, removing and installing the flywheel housing, removing and installing the crankshaft pulley, and removing and installing the crankshaft front seal. The procedures provide illustrations and specify any required tools.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 compact track loader. It describes how to install the flywheel, including cleaning and heating the ring gear. It also details removing and installing the crankshaft rear seal, crankshaft rear seal carrier, flywheel housing, crankshaft pulley, and crankshaft front seal. Tools required are listed for each procedure.
The document provides instructions for removing and installing various engine components on a Caterpillar C3.8 engine, including:
- Installing the flywheel, ensuring the ring gear is oriented correctly
- Removing and installing the crankshaft rear seal and carrier
- Removing and installing the flywheel housing
- Removing and installing the crankshaft pulley
The procedures include lists of required tools and step-by-step instructions with accompanying illustrations. Safety and installation notes are provided throughout.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 compact track loader. It includes procedures for installing the flywheel, removing and installing the crankshaft rear seal and carrier, removing and installing the flywheel housing, removing and installing the crankshaft pulley, and removing and installing the crankshaft front seal. The procedures provide illustrations and specify any required tools.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 compact track loader. It describes how to install the flywheel, including cleaning and heating the ring gear. It also details removing and installing the crankshaft rear seal, crankshaft rear seal carrier, flywheel housing, crankshaft pulley, and crankshaft front seal. The procedures note any required tools and provide illustrations to support the step-by-step instructions.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 compact track loader. It includes procedures for installing the flywheel, removing and installing the crankshaft rear seal and carrier, removing and installing the flywheel housing, removing and installing the crankshaft pulley, and removing and installing the crankshaft front seal. The procedures provide illustrations and specify any required tools.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 compact track loader. It describes how to install the flywheel, including cleaning and heating the ring gear. It also details removing and installing the crankshaft rear seal, crankshaft rear seal carrier, flywheel housing, crankshaft pulley, and crankshaft front seal. The procedures note any required tools and provide illustrations to support the step-by-step instructions.
The document provides instructions for removing and installing various engine components on a Caterpillar C3.8 engine, including:
- Installing the flywheel, ensuring the ring gear is oriented correctly
- Removing and installing the crankshaft rear seal and carrier
- Removing and installing the flywheel housing
- Removing and installing the crankshaft pulley
The procedures include lists of required tools and step-by-step instructions with accompanying illustrations. Safety and installation notes are provided throughout.
The document provides instructions to remove and install the valve mechanism cover on a Caterpillar C3.8 engine. The removal procedure involves disconnecting wire harnesses, tubes, and bolts. The cover and gasket are then removed. Installation is the reverse of removal, requiring reinstallation of the cover, gasket, bolts, wires, and tubes. Bolts and nuts are tightened to specified torque values.
The document provides instructions to remove and install the valve mechanism cover on a Caterpillar C3.8 engine. The removal procedure involves disconnecting wire harnesses, tubes, and bolts. The cover and gasket are then removed. Installation is the reverse of removal, requiring reinstallation of the cover and gaskets and tightening of bolts and nuts to the specified torques.
The document provides instructions to remove and install the valve mechanism cover on a Caterpillar C3.8 engine. The removal procedure involves disconnecting wire harnesses, tubes, and bolts. The cover and gasket are then removed. Installation is the reverse of removal, requiring reinstallation of the cover, gasket, bolts, wires and tubes. Bolts and nuts are tightened to specified torque values.
The document provides instructions for removing and installing an idler gear on a Caterpillar 299D2 XHP compact track loader. The removal procedure involves removing the front housing, ensuring the piston and gear timing marks are aligned, installing a flywheel stopper tool, and removing bolts and plates. The installation procedure specifies reversing the removal steps and tightening bolts to the specified torque values.
The document provides instructions for removing and installing an idler gear on a Caterpillar 299D2 XHP compact track loader. The removal procedure involves removing the front housing, ensuring the piston and gear timing marks are aligned, installing a flywheel stopper tool, and removing bolts and plates. The installation procedure specifies cleaning and lubricating parts, ensuring the bushing is flush, and tightening bolts to the specified torque.
The document provides instructions for removing and installing an idler gear on a Caterpillar 299D2 XHP compact track loader. The removal procedure involves removing the front housing, ensuring the piston and gear timing marks are aligned, installing a flywheel stopper tool, and removing bolts and plates. The installation procedure specifies cleaning and lubricating parts, ensuring components are flush, and tightening bolts to the specified torque using a flywheel stopper tool.
The document provides instructions for removing and installing an idler gear on a Caterpillar 299D2 XHP compact track loader. The removal procedure involves removing the front housing, ensuring the piston and gear timing marks are aligned, installing a flywheel stopper tool, and removing bolts and plates. The installation procedure specifies installing the idler gear in reverse order and tightening the bolts to the specified torque.
The document provides instructions for removing and installing an idler gear on a Caterpillar 299D2 XHP compact track loader. The removal procedure involves removing the front housing, ensuring the piston is at top center position, marking gear alignment, installing a flywheel stopper tool, and removing bolts, plates and the idler gear. The installation procedure specifies cleaning and applying oil to parts, ensuring correct bushing alignment, and tightening bolts to the specified torque.
Similar to Caterpillar cat 299 d2 compact track loader (prefix by4) service repair manual (by400001 and up) (20)
New holland l228 tier 4 b (final) skid steer loader service repair manual [ng...jjdkksmmdmed
This document provides service information for New Holland compact track loaders and skid steer loaders, including:
- Procedures for draining engine oil either through a remote drain hose or a quick-disconnect fitting.
- Safety precautions to avoid injury such as using lifting equipment, avoiding contact with hot fluids, and preventing chemical hazards.
- Illustrations and part numbers for drain plugs, caps, hoses and other components involved in the oil drain process.
New holland d180 c bd tier 2 crawler dozer service repair manualjjdkksmmdmed
This service manual section provides instructions for removing and installing the engine on a D180C Crawler Dozer. The removal process involves detaching the engine from the frame using lifting equipment at specified lift points. Reinstallation requires aligning and securing the engine to the frame, pump stack, and flexible coupling components using bolts, washers and LOCTITE. Proper balancing and support of heavy parts is emphasized for safety.
New holland d150 c tier 2 crawler dozer service repair manual (pin nedc15000 ...jjdkksmmdmed
This document is a service manual for D150C crawler dozers that provides specifications and repair procedures. It covers the engine, hydrostatic drive, brakes and controls, hydraulic systems, tracks and suspension, climate control, electrical systems, dozer blade, tools, and bodywork. The manual contains sections on safety, product identification, and maintenance instructions for technicians.
New holland d125 c stage iiib crawler dozer service repair manual (pin nfdc12...jjdkksmmdmed
This service manual section provides instructions for removing the engine from a D125C crawler dozer. Key steps include disconnecting electrical connections, hoses, and pipes; removing the air cleaner assembly, turbocharger pipe, and cooling package; and then removing mounting bolts to separate the engine from the vehicle. Proper disconnection of all components is emphasized for safety.
New holland cx8080 elevation combine harvesters service repair manualjjdkksmmdmed
This service manual provides information for servicing and repairing CNH Industrial CR and CX series combines. It includes technical specifications, diagrams, troubleshooting procedures, and instructions for repairing and replacing components. The manual is divided into sections covering the engine, transmission, axles, hydraulics, electrical systems, attachments, and other major systems on the combines. It is intended to help technicians maintain and repair CNH Industrial CR and CX series combines.
New holland cx8040 combine harvesters service repair manualjjdkksmmdmed
The document provides a service manual for various New Holland combine harvester models. It describes the primary hydraulic power system, which uses a variable displacement pump to power critical systems like steering, the header, and threshing functions. Oil is filtered and distributed to valves that control lift cylinders, motors, and other components. The system is linked to the hydrostatic circuit to share the oil reservoir and cooling.
New holland cx5090 tier 3 combine harvester service repair manualjjdkksmmdmed
The document is a service manual that provides information on hydraulic, pneumatic, electrical, and electronic systems for CX5000 and CX6000 series equipment. It includes:
- Specifications and torque values for hydraulic fittings and connections
- Details on the primary hydraulic power system, including locations of key components like pumps, valves, cylinders. and schematics of fluid flow
- Technical data on hydraulic pumps used in main, steering, and lateral flotation circuits
The manual provides maintenance technicians with the information needed to service hydraulic, electrical, and electronic systems through technical specifications, schematics, and component locations. It aims to support the repair and maintenance of the distribution, power, and control systems.
New holland cr8080 combine harvesters service repair manualjjdkksmmdmed
This service manual provides information for servicing and repairing CNH Industrial CR and CX series combines. It includes technical specifications, diagrams, troubleshooting procedures, and instructions for repairing and replacing components. The manual is divided into sections covering the engine, transmission, axles, hydraulics, electrical systems, attachments, and other major systems on the combines. It is intended to help technicians maintain and repair CNH Industrial CR and CX series combines.
New holland c232 tier 4 b (final) compact track loader service repair manual ...jjdkksmmdmed
This document provides service information for New Holland compact track loaders and skid steer loaders, including:
- Procedures for draining engine oil either through a remote drain hose or a quick-disconnect fitting.
- Safety warnings for lifting heavy components, handling hot fluids, and avoiding skin contact with engine oil.
- Illustrations and part numbers for access covers, drain plugs, caps, and fittings involved in the oil drain process.
New holland b95 c tc four wheel drive (4wd) tier 4b (final) tractor loader ba...jjdkksmmdmed
This document provides service information for New Holland B95C, B95C LR, B95C TC, and B110C tractor loader backhoes, including specifications for the Tier 4B compliant engines. The engines are 4-cylinder turbocharged diesel engines with direct fuel injection. Engine details and specifications are provided for the B95C and B110C models. The document also contains sections covering the transmission, axle systems, brakes, hydraulics, electrical systems, and other components.
This document provides instructions for removing and installing various engine components on a Caterpillar 299D2 compact track loader, including:
- Removing and installing the engine oil relief valve.
- Removing and installing the engine oil pump.
- Removing and installing the water pump.
- Removing and installing the water temperature regulator.
- Removing the flywheel and installing a new ring gear if needed.
The procedures provide illustrations and specify torque specifications and safety precautions for each component.
Caterpillar cat 299 d xhp compact track loader (prefix nlc) service repair ma...jjdkksmmdmed
This document provides removal and installation instructions for servicing various engine components on a 299D XHP Compact Track Loader, including the diesel particulate filter, air inlet heater, inlet manifold, inlet and exhaust valves, and engine oil cooler. Detailed steps and illustrations are provided for each procedure, along with safety information and torque specifications.
Caterpillar cat 299 d xhp compact track loader (prefix jst) service repair ma...jjdkksmmdmed
The document provides instructions for removing and installing various engine components on a Caterpillar 299D XHP compact track loader, including:
- Water pump removal and installation procedures involving removing guards, belts, bolts, and gaskets.
- Water temperature regulator removal involving disconnecting hoses and removing bolts, cover, and gasket.
- Flywheel removal involving removing bolts, pump coupling, and lifting the flywheel assembly off.
- Crankshaft rear seal removal by drilling holes in the seal and using a slide hammer, and installation using a driver tool.
- Crankshaft rear seal carrier removal by removing bolts and the bearing case cover, and installation by
Caterpillar cat 299 d compact track loader (prefix gtc) service repair manual...jjdkksmmdmed
The document provides instructions for removing and installing various engine components on a Caterpillar 299D compact track loader, including:
- Removing and installing the fuel injection pump by disconnecting fuel lines, removing mounting bolts and gears, and reinstalling in reverse order.
- Removing and installing electronic unit injectors by removing mounting nuts and clamps, overflow pipes, and seals, and reinstalling in reverse order with new seals.
- Removing and installing the turbocharger by removing exhaust connection nuts and bolts and reinstalling with anti-seize on fasteners.
- Removing and installing the mass air flow pressure sensor by disconnecting hoses and electrical connections and removing mounting screws.
-
Caterpillar cat 297 d2 multi terrain loader (prefix bl7) service repair manua...jjdkksmmdmed
This document provides instructions for removing and installing various components of a Caterpillar C3.8 engine, including the air inlet heater, inlet manifold, inlet and exhaust valves, engine oil cooler, engine oil relief valve, and engine oil pump. The procedures include illustrations and specify torque values for fasteners. Safety notices are included to warn of potential injury from compressed springs.
Caterpillar cat 297 d xhp multi terrain loader (prefix hp7) service repair ma...jjdkksmmdmed
The document provides instructions for removing and installing various components of a Caterpillar 297D XHP Multi Terrain Loader engine, including:
- Removing and installing the fuel injection pump by disconnecting fuel lines, removing mounting bolts and gears, and reinstalling in reverse order.
- Removing and installing electronic unit injectors by removing mounting nuts and clamps, injector seals, and reinstalling in reverse order.
- Removing and installing the turbocharger by removing mounting nuts and bolts, disconnecting hoses and tubes, and reinstalling with new gaskets and anti-seize on bolts.
- Removing and installing the mass air flow pressure sensor by disconnecting hoses and harness
Caterpillar cat 297 d multi terrain loader (prefix be7) service repair manual...jjdkksmmdmed
The document provides instructions for removing and installing a camshaft on a Caterpillar C3.8 engine. The removal process includes marking the alignment of gears, removing bolts and a pulsar gear to access the camshaft. For installation, the camshaft is lubricated and installed along with gears and bolts, ensuring proper alignment of components.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
2. Shutdown SIS
Previous Screen
Product: COMPACT TRACK LOADER
Model: 299D2 COMPACT TRACK LOADER BY4
Configuration: 299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWERED BY C3.8 Engine
Disassembly and Assembly
C3.8 Engines for Caterpillar Built Machines
Media Number -UENR0129-08 Publication Date -01/09/2015 Date Updated -19/05/2016
i04664023
Flywheel - Install
SMCS - 1156-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-7994 Guide Bolt 2
Always wear protective gloves when handling parts that have been
heated.
1/4299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g02797127
Typical example
1. If the ring gear was removed, follow Steps 1.a through 1.c to install ring gear (7) to flywheel
(8).
a. Identify the orientation of the new ring gear in order to install the ring gear correctly
onto the flywheel.
Note: The chamfered side of gear teeth (Y) must face toward the starting motor when
the flywheel is installed. This will ensure the correct engagement of the starting
motor.
b. Heat ring gear (3) in an oven to a maximum temperature of 150°C (302°F) prior to
installation.
Note: Do not use a torch to heat the ring gear.
c. Ensure that the orientation of ring gear (7) is correct and quickly install the ring gear
onto flywheel (8).
Illustration 2 g02797120
2/4299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 2. Thoroughly clean the flywheel housing. Inspect the crankshaft rear seal for leaks. If there
are any oil leaks replace the crankshaft rear seal. Refer to Disassembly and Assembly,
"Crankshaft Rear Seal - Remove and Install".
3. Install Tooling (A) on the crankshaft.
4. Use a suitable lifting device to position flywheel assembly (5). The weight of flywheel
assembly (5) is approximately 23 kg (50 lb).
5. Align flywheel assembly (5) with Tooling (A). Install flywheel assembly (5) to the
crankshaft.
Note: Ensure the correct orientation of the flywheel on the crankshaft.
6. Apply clean engine oil onto bolts (6). Install bolts (6) finger tight.
7. Remove Tooling (A) and install the two remaining bolts (6).
8. Remove the lifting device from the flywheel.
9. Use a suitable tool to prevent flywheel assembly (5) from rotating. Tighten bolts (6) to a
torque of 98.1 to 107 N·m (72 to 79 lb ft).
10. Check the concentricity of the flywheel. Refer to Systems Operation, Testing and Adjusting,
"Flywheel - Inspect".
Illustration 3 g02797118
11. Install pump coupling (4). Install bolts (3).
3/4299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 4 g02797115
12. Install cover (2). Install bolts (1).
End By:
a. Install the starting motor.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 30 23:51:46 UTC+0800 2019
4/4299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: COMPACT TRACK LOADER
Model: 299D2 COMPACT TRACK LOADER BY4
Configuration: 299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWERED BY C3.8 Engine
Disassembly and Assembly
C3.8 Engines for Caterpillar Built Machines
Media Number -UENR0129-08 Publication Date -01/09/2015 Date Updated -19/05/2016
i04664019
Crankshaft Rear Seal - Remove and Install
SMCS - 1161-010
Removal Procedure
Start By:
a. Remove the flywheel.
Illustration 1 g02797554
1. Drill three holes in lip seal (1). Use a suitable slide hammer to remove lip seal (1).
2. Remove ring seal (2).
Installation Procedure
Table 1
Required Tools
1/2299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Tool Part Number Part Description Qty
A 393-2571 Driver 1
Illustration 2 g02797554
Illustration 3 g02870418
1. Use Tooling (A) to install ring seal (2).
2. Use Tooling (A) to install lip seal (1).
End By:
a. Install the flywheel.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 30 23:52:42 UTC+0800 2019
2/2299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Shutdown SIS
Previous Screen
Product: COMPACT TRACK LOADER
Model: 299D2 COMPACT TRACK LOADER BY4
Configuration: 299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWERED BY C3.8 Engine
Disassembly and Assembly
C3.8 Engines for Caterpillar Built Machines
Media Number -UENR0129-08 Publication Date -01/09/2015 Date Updated -19/05/2016
i04839813
Crankshaft Rear Seal Carrier - Remove and Install
SMCS - 1161-010-C3
Removal Procedure
1. Refer to Specifications, "Crankshaft".
Illustration 1 g02869998
2. Remove bolts (1). Use two of bolts (1) to remove bearing case cover (2) .
1/3299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 2 g02870025
3. Remove lip seal (3) from bearing case cover (2) .
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 393-2571 Seal Installer 1
B - Three Bond 1217H -
Illustration 3 g02870025
2/3299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 4 g02870418
1. Use Tooling (A) to install lip seal (3) into bearing case cover (2) .
Illustration 5 g02869998
2. Apply Tooling (B) onto the mating surface of bearing case cover (2). Apply clean engine oil
onto the lip seal. Install bearing case cover (2) .
3. Install bolts (1). Tighten bolts (1) to a torque of 25.5 ± 1.5 N·m (18.8 ± 1.1 lb ft).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 30 23:53:38 UTC+0800 2019
3/3299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: COMPACT TRACK LOADER
Model: 299D2 COMPACT TRACK LOADER BY4
Configuration: 299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWERED BY C3.8 Engine
Disassembly and Assembly
C3.8 Engines for Caterpillar Built Machines
Media Number -UENR0129-08 Publication Date -01/09/2015 Date Updated -19/05/2016
i06272842
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 439-3938 Link Bracket 2
B - Three Bond1217H 1
Start By:
a. Remove the bearing case cover.
Illustration 1 g02797548
1/2299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. 1. Attach Tooling (A) and a suitable lifting device onto flywheel housing (1). The weight of
flywheel housing (1) is approximately 45 kg (100 lb).
2. Remove bolts (2) and bolts (3). Remove flywheel housing (1).
Installation Procedure
1. Install flywheel housing (1) in the reverse order of removal.
a. Apply Tooling (B) onto the mating surface of flywheel housing (1).
b. For the SSL, MTL, and CTL models that end in D2 models (BL2, MD2, BL7, HP2,
FD2, DX2, DX9, and BY4), tighten bolts (3) and bolts (2) to a torque of
103 ± 14 N·m (76 ± 10 lb ft).
c. For all other models, tighten bolts (3) and bolts (2) to a torque of 78 ± 12 N·m
(56 ± 9 lb ft).
d. Refer to Systems Operation, Testing and Adjusting, "Flywheel Housing - Inspect".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 30 23:54:34 UTC+0800 2019
2/2299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: COMPACT TRACK LOADER
Model: 299D2 COMPACT TRACK LOADER BY4
Configuration: 299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWERED BY C3.8 Engine
Disassembly and Assembly
C3.8 Engines for Caterpillar Built Machines
Media Number -UENR0129-08 Publication Date -01/09/2015 Date Updated -19/05/2016
i04664013
Crankshaft Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 393-2572 Flywheel Stopper 1
Start By:
a. Remove the belt.
1. Install Tooling (A) onto the flywheel.
Illustration 1 g02860756
2. Remove bolt (1) to remove pulley (2).
1/2299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Installation Procedure
1. Install pulley (2) in the reverse order of removal.
a. Apply clean engine oil onto bolt (1).
b. Tighten bolt (1) to a torque of 264.5 ± 9.5 N·m (195.1 ± 7.0 lb ft).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 30 23:55:29 UTC+0800 2019
2/2299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: COMPACT TRACK LOADER
Model: 299D2 COMPACT TRACK LOADER BY4
Configuration: 299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWERED BY C3.8 Engine
Disassembly and Assembly
C3.8 Engines for Caterpillar Built Machines
Media Number -UENR0129-08 Publication Date -01/09/2015 Date Updated -19/05/2016
i04664010
Crankshaft Front Seal - Remove and Install
SMCS - 1160-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-8145 Drill Bit (4.10 mm) 1
B 1U-7600 Slide Hammer Puller 1
Start By:
a. Remove the crankshaft pulley.
NOTICE
Ensure that the main lip is used in order to remove the crankshaft
front seal. Do not damage the edge of the housing for the crankshaft
front seal.
1/3299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 1 g02860787
1. Use Tooling (A) to drill three evenly spaced holes in crankshaft front seal (1).
2. Use Tooling (B) to carefully remove crankshaft front seal (1). Alternate the position of
Tooling (B) from one hole to another hole to allow the crankshaft front seal to be removed.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
C 393-2570 Seal Installer 1
Illustration 2 g02860787
2/3299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 3 g02866181
1. Lubricate the outside diameter of a new crankshaft front seal (1) with clean engine oil. Use
Tooling (C) to install crankshaft front seal (1).
2. Apply clean engine oil to the lip of crankshaft front seal (1).
End By:
a. Install the crankshaft pulley.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 30 23:56:25 UTC+0800 2019
3/3299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
19. Shutdown SIS
Previous Screen
Product: COMPACT TRACK LOADER
Model: 299D2 COMPACT TRACK LOADER BY4
Configuration: 299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWERED BY C3.8 Engine
Disassembly and Assembly
C3.8 Engines for Caterpillar Built Machines
Media Number -UENR0129-08 Publication Date -01/09/2015 Date Updated -19/05/2016
i04801361
Idler Gear - Remove and Install
SMCS - 1206
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 393-2572 Flywheel Stopper 1
B 393-2573 Driver 1
Start By:
a. Remove the front housing.
1. Ensure that number four piston is at the top center position on the compression stroke. Refer
to Systems Operation, Testing and Adjusting, "Finding Top Center Position for No. 4
Piston".
1/3299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 1 g02871716
2. Ensure that timing marks on the gears are aligned.
Alternatively, make temporary timing marks on the gears in order to show alignment.
3. Install Tooling (A) onto the flywheel. Remove bolts (1) and plate (2).
Illustration 2 g02872045
4. Remove idler gear (3), shaft (4), and plate (5).
2/3299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 3 g02920337
5. Use Tooling (B) to remove bushing (6) from idler gear (3).
Installation Procedure
1. Install idler gear (3) in the reverse order of removal.
a. Apply clean engine oil onto the bore of idler gear (3) and bushing (6).
b. Ensure that edge of bushing (6) is flush with the edge of the bore that is in idler gear
(3).
c. Tighten bolts (1) to a torque of 25.5 ± 1.5 N·m (18.8 ± 1.1 lb ft).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 30 23:57:21 UTC+0800 2019
3/3299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: COMPACT TRACK LOADER
Model: 299D2 COMPACT TRACK LOADER BY4
Configuration: 299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWERED BY C3.8 Engine
Disassembly and Assembly
C3.8 Engines for Caterpillar Built Machines
Media Number -UENR0129-08 Publication Date -01/09/2015 Date Updated -19/05/2016
i06662240
Idler Gear - Remove and Install
SMCS - 1206
S/N - BL21-UP
S/N - BL71-UP
S/N - BY41-UP
S/N - DX21-UP
S/N - DX91-UP
S/N - FD21-UP
S/N - HP21-UP
S/N - MD21-UP
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 393-2572 Flywheel Stopper 1
Start By:
a. Remove the front housing.
1. Ensure that number four piston is at the top center position on the compression stroke. Refer
to Systems Operation, Testing and Adjusting, "Finding Top Center Position for No. 4
Piston".
1/2299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 1 g06066040
2. Ensure that timing marks on the gears are aligned.
Alternatively, make temporary timing marks on the gears to show alignment.
3. Install Tooling (A) onto the flywheel. Remove bolts (2) and idler gear (3).
4. Remove nuts (1) and idler gear (4).
Installation Procedure
1. Install the idler gears in the reverse order of removal.
a. Tighten nuts (1) to a torque of 24 N·m to 27 N·m (212 lb in to 239 lb in).
b. Tighten bolts (2) to a torque of 24 N·m to 27 N·m (212 lb in to 239 lb in).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 30 23:58:16 UTC+0800 2019
2/2299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...