The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 compact track loader. It describes how to install the flywheel, including cleaning and heating the ring gear. It also details removing and installing the crankshaft rear seal, crankshaft rear seal carrier, flywheel housing, crankshaft pulley, and crankshaft front seal. The procedures note any required tools and provide illustrations to support the step-by-step instructions.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 compact track loader, including:
- Removing and installing the flywheel, which involves cleaning surfaces, heating the ring gear, and torquing bolts to a specified value.
- Removing and installing the crankshaft rear seal, which involves drilling holes, using a slide hammer, and pressing in new seals.
- Removing and installing the crankshaft rear seal carrier, bearing case cover, and lip seal using seal installation tools and threadlocker.
- Removing and installing the flywheel housing, which requires lifting equipment and torquing bolts to a specified value.
-
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 compact track loader, including:
- Removing and installing the flywheel, which involves cleaning surfaces, heating the ring gear, and torquing bolts to a specified value.
- Removing and installing the crankshaft rear seal, which involves drilling holes, using a slide hammer, and pressing in new seals.
- Removing and installing the crankshaft rear seal carrier, bearing case cover, and lip seal using seal installation tools and threadlocker.
- Removing and installing the flywheel housing, which requires lifting equipment and torquing bolts to a specified value.
-
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 Compact Track Loader, including:
- Flywheel installation which requires cleaning surfaces, heating the ring gear, and torquing bolts to a specified value.
- Crankshaft rear seal replacement involving removing the old seal and pressing in a new one using specific tools.
- Removing and installing the flywheel housing which requires attaching lifting brackets and torquing bolts to a specified value.
- Procedures for the crankshaft pulley, front seal, and bearing case cover that include cleaning, applying oil, and ensuring proper torque on fasteners.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 Compact Track Loader, including:
- Flywheel installation which requires cleaning surfaces, heating the ring gear, and torquing bolts to a specified value.
- Crankshaft rear seal replacement involving removing the old seal and pressing in a new one using specific tools.
- Removing and installing the flywheel housing which requires attaching lifting equipment and torquing bolts to a specified value.
- Procedures for the crankshaft pulley, front seal, and bearing case cover that include cleaning, applying oil, and ensuring proper orientation of parts.
The document provides instructions to remove and install the valve mechanism cover on a Caterpillar C3.8 engine. The removal procedure involves disconnecting wire harnesses, tubes, and bolts. The cover and gasket are then removed. Installation is the reverse of removal, requiring reinstallation of the cover, gasket, bolts, wires, and tubes. Bolts and nuts are tightened to specified torque values.
The document provides instructions to remove and install the valve mechanism cover on a Caterpillar C3.8 engine. The removal procedure involves disconnecting wire harnesses, tubes, and bolts. The cover and gasket are then removed. Installation is the reverse of removal, requiring reinstallation of the cover and gaskets and tightening of bolts and nuts to the specified torques.
The document provides instructions to remove and install the valve mechanism cover on a Caterpillar C3.8 engine. The removal procedure involves disconnecting wire harnesses, tubes, and bolts. The cover and gasket are then removed. Installation is the reverse of removal, requiring reinstallation of the cover, gasket, bolts, wires and tubes. Bolts and nuts are tightened to specified torque values.
The document provides instructions for removing and installing an idler gear on a Caterpillar 299D2 XHP compact track loader. The removal procedure involves removing the front housing, ensuring the piston is at top center position, marking gear alignment, installing a flywheel stopper tool, and removing bolts, plates and the idler gear. The installation procedure specifies cleaning and applying oil to parts, ensuring correct bushing alignment, and tightening bolts to the specified torque.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 compact track loader, including:
- Removing and installing the flywheel, which involves cleaning surfaces, heating the ring gear, and torquing bolts to a specified value.
- Removing and installing the crankshaft rear seal, which involves drilling holes, using a slide hammer, and pressing in new seals.
- Removing and installing the crankshaft rear seal carrier, bearing case cover, and lip seal using seal installation tools and threadlocker.
- Removing and installing the flywheel housing, which requires lifting equipment and torquing bolts to a specified value.
-
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 compact track loader, including:
- Removing and installing the flywheel, which involves cleaning surfaces, heating the ring gear, and torquing bolts to a specified value.
- Removing and installing the crankshaft rear seal, which involves drilling holes, using a slide hammer, and pressing in new seals.
- Removing and installing the crankshaft rear seal carrier, bearing case cover, and lip seal using seal installation tools and threadlocker.
- Removing and installing the flywheel housing, which requires lifting equipment and torquing bolts to a specified value.
-
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 Compact Track Loader, including:
- Flywheel installation which requires cleaning surfaces, heating the ring gear, and torquing bolts to a specified value.
- Crankshaft rear seal replacement involving removing the old seal and pressing in a new one using specific tools.
- Removing and installing the flywheel housing which requires attaching lifting brackets and torquing bolts to a specified value.
- Procedures for the crankshaft pulley, front seal, and bearing case cover that include cleaning, applying oil, and ensuring proper torque on fasteners.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 Compact Track Loader, including:
- Flywheel installation which requires cleaning surfaces, heating the ring gear, and torquing bolts to a specified value.
- Crankshaft rear seal replacement involving removing the old seal and pressing in a new one using specific tools.
- Removing and installing the flywheel housing which requires attaching lifting equipment and torquing bolts to a specified value.
- Procedures for the crankshaft pulley, front seal, and bearing case cover that include cleaning, applying oil, and ensuring proper orientation of parts.
The document provides instructions to remove and install the valve mechanism cover on a Caterpillar C3.8 engine. The removal procedure involves disconnecting wire harnesses, tubes, and bolts. The cover and gasket are then removed. Installation is the reverse of removal, requiring reinstallation of the cover, gasket, bolts, wires, and tubes. Bolts and nuts are tightened to specified torque values.
The document provides instructions to remove and install the valve mechanism cover on a Caterpillar C3.8 engine. The removal procedure involves disconnecting wire harnesses, tubes, and bolts. The cover and gasket are then removed. Installation is the reverse of removal, requiring reinstallation of the cover and gaskets and tightening of bolts and nuts to the specified torques.
The document provides instructions to remove and install the valve mechanism cover on a Caterpillar C3.8 engine. The removal procedure involves disconnecting wire harnesses, tubes, and bolts. The cover and gasket are then removed. Installation is the reverse of removal, requiring reinstallation of the cover, gasket, bolts, wires and tubes. Bolts and nuts are tightened to specified torque values.
The document provides instructions for removing and installing an idler gear on a Caterpillar 299D2 XHP compact track loader. The removal procedure involves removing the front housing, ensuring the piston is at top center position, marking gear alignment, installing a flywheel stopper tool, and removing bolts, plates and the idler gear. The installation procedure specifies cleaning and applying oil to parts, ensuring correct bushing alignment, and tightening bolts to the specified torque.
The document provides instructions for removing and installing an idler gear on a Caterpillar 299D2 XHP compact track loader. The removal procedure involves removing the front housing, ensuring the piston is at top center position, marking timing gear alignment, installing a flywheel stopper tool, and removing bolts and plates. The installation procedure specifies cleaning and applying oil to parts, ensuring correct bushing alignment, and torquing bolts to the specified values.
The document provides instructions for removing and installing an idler gear on a Caterpillar 299D2 XHP compact track loader. The removal procedure involves removing the front housing, ensuring the piston is at top center position, marking timing gear alignment, installing a flywheel stopper tool, and removing bolts and plates. The installation procedure specifies cleaning and applying oil to parts, ensuring correct bushing alignment, and torquing bolts to the specified values.
The document provides instructions for removing and installing an idler gear on a Caterpillar 299D2 XHP compact track loader. The removal procedure involves removing the front housing, ensuring the piston is at top center position, marking gear alignment, installing a flywheel stopper tool, and removing bolts, plates and the idler gear. The installation procedure specifies cleaning and applying oil to parts, ensuring correct bushing alignment, and tightening bolts to the specified torque.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 XHP compact track loader. The procedures include removing the idler gear by first ensuring the engine is at top center position and removing bolts. Other removal procedures include the front housing, fumes disposal filter, valve mechanism cover and related components. Reinstallation is done in reverse order, applying oil and torquing bolts to the specified values.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 XHP compact track loader. The procedures include removing the idler gear by first ensuring the engine is at top center position and removing bolts. Other removal procedures include the front housing, fumes disposal filter, and valve mechanism cover. Reinstallation is done by reversing the removal steps and tightening bolts to the specified torques.
The document provides instructions to remove and install a valve mechanism cover on a Caterpillar C3.8 engine. It describes:
1. Disconnecting various tubes, harnesses, and hoses attached to the cover.
2. Removing bolts to take off the cover and gasket.
3. Cleaning and inspecting the mating surfaces before installing the new cover in reverse order using specified torques for the bolts.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 XHP compact track loader. The procedures include removing the idler gear by first ensuring the engine is at top center position and removing bolts, nuts and plates. The front housing is removed by disconnecting wiring harnesses and belts, removing bolts, and using a flywheel stopper tool. The fumes disposal filter is removed by disconnecting hoses and removing a bolt and bracket.
The document provides instructions to remove and install a valve mechanism cover on a Caterpillar C3.8 engine. It describes:
1. Disconnecting various tubes, harnesses, and hoses attached to the cover.
2. Removing bolts to take off the cover and gasket.
3. Cleaning and inspecting the mating surfaces before installing the new cover in reverse order using specified torques for the bolts.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 XHP compact track loader. The procedures include removing the idler gear by first ensuring the engine is at top center position and removing bolts, nuts and plates. The front housing is removed by disconnecting wiring harnesses and belts, removing bolts, and using a flywheel stopper tool. The fumes disposal filter is removed by disconnecting hoses and removing a bolt and bracket.
The document provides instructions to remove and install a valve mechanism cover on a Caterpillar C3.8 engine. It describes:
1. Disconnecting various tubes, harnesses, and hoses attached to the cover.
2. Removing bolts to take off the cover and gasket.
3. Cleaning and inspecting the mating surfaces before installing the new cover in reverse order using specified torques for the bolts.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 XHP compact track loader. The procedures include removing the idler gear by first ensuring the engine is at top center position and removing bolts. Other removal procedures include the front housing, fumes disposal filter, valve mechanism cover and related components. Reinstallation is done by reversing the removal steps and tightening bolts to the specified torques.
The document provides instructions for removing and installing an idler gear on a Caterpillar 299D2 XHP compact track loader. The removal procedure involves removing the front housing, ensuring the piston and gear timing marks are aligned, installing a flywheel stopper tool, and removing bolts and plates. The installation procedure specifies reversing the removal steps and tightening bolts to the specified torque values.
The document provides instructions for removing and installing an idler gear on a Caterpillar 299D2 XHP compact track loader. The removal procedure involves removing the front housing, ensuring the piston and gear timing marks are aligned, installing a flywheel stopper tool, and removing bolts and plates. The installation procedure specifies cleaning and lubricating parts, ensuring the bushing is flush, and tightening bolts to the specified torque.
The document provides instructions for removing and installing an idler gear on a Caterpillar 299D2 XHP compact track loader. The removal procedure involves removing the front housing, ensuring the piston and gear timing marks are aligned, installing a flywheel stopper tool, and removing bolts and plates. The installation procedure specifies cleaning and lubricating parts, ensuring components are flush, and tightening bolts to the specified torque using a flywheel stopper tool.
The document provides instructions for removing and installing an idler gear on a Caterpillar 299D2 XHP compact track loader. The removal procedure involves removing the front housing, ensuring the piston and gear timing marks are aligned, installing a flywheel stopper tool, and removing bolts and plates. The installation procedure specifies installing the idler gear in reverse order and tightening the bolts to the specified torque.
Caterpillar Cat 329D2 and 329D2L Excavator (Prefix RGA) Service Repair Manual...gongfuao7509
The document provides instructions for disassembling and assembling a swing motor and swing drive. Key steps include:
1. Cleaning all parts thoroughly before assembly and applying a light film of hydraulic oil.
2. Using retaining ring pliers to install a retaining ring and assembling plates, pistons, a barrel and other components into the motor housing in the specified order.
3. Attaching lifting brackets and safely lifting the heavy swing motor or drive components during removal and installation procedures.
Caterpillar Cat 329D and 329D L Excavator (Prefix DTZ) Service Repair Manual ...gongfuao7509
This document provides instructions for removing and installing the water temperature regulator on a Caterpillar C7 engine. It describes:
1. Draining the engine coolant below the level of the water temperature regulator.
2. Disconnecting the hose from the regulator cover and removing mounting bolts.
3. Installing the new regulator by reversing the removal steps, filling the cooling system, and tightening all connections to the specified torques.
Cleanliness is important to prevent contamination, and safety precautions are described for working with hot coolant and steam.
Caterpillar Cat 326F L Excavator (Prefix WGL) Service Repair Manual Instant D...gongfuao7509
This document provides instructions to disassemble a travel motor. It begins by having the technician remove the travel motor and attach it to assembly tools. It then lists 28 steps to fully disassemble the travel motor by removing components like caps, springs, seals, plates and housing assemblies. Safety notices are included throughout to warn of potential injury from released spring forces.
Caterpillar Cat 324E L Excavator (Prefix PNW) Service Repair Manual Instant D...gongfuao7509
This document provides instructions for disassembling and assembling the travel motor of a 324E L Excavator. It lists the required tools and parts and provides 28 steps to disassemble the travel motor by removing components like the head, O-rings, springs, brake piston, plates, and bearings. It then lists 19 steps to assemble the travel motor by reinstalling these components in the reverse order, noting proper lubrication and alignment of parts.
This document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator. It includes procedures for removing and installing the front cover, front housing, camshaft idler gear, valve mechanism cover, valve mechanism cover base, rocker shaft and pushrods. The document provides illustrations and specifies required tools for each procedure. Safety notices are included to keep parts clean and contain fluids.
Caterpillar Cat 324D FM LL EXCAVATOR (Prefix JLS) Service Repair Manual Insta...gongfuao7509
This document provides instructions for disassembling and assembling the final drive of a 324D FM LL EXCAVATOR. It outlines 21 steps for disassembly, which include removing plates, springs, pistons, gears, and other components. It also outlines 16 steps for assembly, which include installing bearings, seals, gears, and other components back into the final drive housing using various tools. The document includes illustrations to supplement the written instructions.
Caterpillar Cat 323F SA and 323F LN Excavator (Prefix FA2) Service Repair Man...gongfuao7509
This document provides instructions for disassembling and assembling the final drive of an excavator model 323F SA. It lists 30 steps to disassemble the final drive by removing components like the cover, carrier assembly, ring gears, and seals. It then lists 31 steps to reassemble the final drive by installing components like bearings, seals, gears, and shims in the reverse order of disassembly. Precise tools and procedures are required due to the heavy weight and precision fitting of components.
More Related Content
Similar to Caterpillar Cat 299D2 COMPACT TRACK LOADER (Prefix BY4) Service Repair Manual Instant Download.pdf
The document provides instructions for removing and installing an idler gear on a Caterpillar 299D2 XHP compact track loader. The removal procedure involves removing the front housing, ensuring the piston is at top center position, marking timing gear alignment, installing a flywheel stopper tool, and removing bolts and plates. The installation procedure specifies cleaning and applying oil to parts, ensuring correct bushing alignment, and torquing bolts to the specified values.
The document provides instructions for removing and installing an idler gear on a Caterpillar 299D2 XHP compact track loader. The removal procedure involves removing the front housing, ensuring the piston is at top center position, marking timing gear alignment, installing a flywheel stopper tool, and removing bolts and plates. The installation procedure specifies cleaning and applying oil to parts, ensuring correct bushing alignment, and torquing bolts to the specified values.
The document provides instructions for removing and installing an idler gear on a Caterpillar 299D2 XHP compact track loader. The removal procedure involves removing the front housing, ensuring the piston is at top center position, marking gear alignment, installing a flywheel stopper tool, and removing bolts, plates and the idler gear. The installation procedure specifies cleaning and applying oil to parts, ensuring correct bushing alignment, and tightening bolts to the specified torque.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 XHP compact track loader. The procedures include removing the idler gear by first ensuring the engine is at top center position and removing bolts. Other removal procedures include the front housing, fumes disposal filter, valve mechanism cover and related components. Reinstallation is done in reverse order, applying oil and torquing bolts to the specified values.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 XHP compact track loader. The procedures include removing the idler gear by first ensuring the engine is at top center position and removing bolts. Other removal procedures include the front housing, fumes disposal filter, and valve mechanism cover. Reinstallation is done by reversing the removal steps and tightening bolts to the specified torques.
The document provides instructions to remove and install a valve mechanism cover on a Caterpillar C3.8 engine. It describes:
1. Disconnecting various tubes, harnesses, and hoses attached to the cover.
2. Removing bolts to take off the cover and gasket.
3. Cleaning and inspecting the mating surfaces before installing the new cover in reverse order using specified torques for the bolts.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 XHP compact track loader. The procedures include removing the idler gear by first ensuring the engine is at top center position and removing bolts, nuts and plates. The front housing is removed by disconnecting wiring harnesses and belts, removing bolts, and using a flywheel stopper tool. The fumes disposal filter is removed by disconnecting hoses and removing a bolt and bracket.
The document provides instructions to remove and install a valve mechanism cover on a Caterpillar C3.8 engine. It describes:
1. Disconnecting various tubes, harnesses, and hoses attached to the cover.
2. Removing bolts to take off the cover and gasket.
3. Cleaning and inspecting the mating surfaces before installing the new cover in reverse order using specified torques for the bolts.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 XHP compact track loader. The procedures include removing the idler gear by first ensuring the engine is at top center position and removing bolts, nuts and plates. The front housing is removed by disconnecting wiring harnesses and belts, removing bolts, and using a flywheel stopper tool. The fumes disposal filter is removed by disconnecting hoses and removing a bolt and bracket.
The document provides instructions to remove and install a valve mechanism cover on a Caterpillar C3.8 engine. It describes:
1. Disconnecting various tubes, harnesses, and hoses attached to the cover.
2. Removing bolts to take off the cover and gasket.
3. Cleaning and inspecting the mating surfaces before installing the new cover in reverse order using specified torques for the bolts.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 XHP compact track loader. The procedures include removing the idler gear by first ensuring the engine is at top center position and removing bolts. Other removal procedures include the front housing, fumes disposal filter, valve mechanism cover and related components. Reinstallation is done by reversing the removal steps and tightening bolts to the specified torques.
The document provides instructions for removing and installing an idler gear on a Caterpillar 299D2 XHP compact track loader. The removal procedure involves removing the front housing, ensuring the piston and gear timing marks are aligned, installing a flywheel stopper tool, and removing bolts and plates. The installation procedure specifies reversing the removal steps and tightening bolts to the specified torque values.
The document provides instructions for removing and installing an idler gear on a Caterpillar 299D2 XHP compact track loader. The removal procedure involves removing the front housing, ensuring the piston and gear timing marks are aligned, installing a flywheel stopper tool, and removing bolts and plates. The installation procedure specifies cleaning and lubricating parts, ensuring the bushing is flush, and tightening bolts to the specified torque.
The document provides instructions for removing and installing an idler gear on a Caterpillar 299D2 XHP compact track loader. The removal procedure involves removing the front housing, ensuring the piston and gear timing marks are aligned, installing a flywheel stopper tool, and removing bolts and plates. The installation procedure specifies cleaning and lubricating parts, ensuring components are flush, and tightening bolts to the specified torque using a flywheel stopper tool.
The document provides instructions for removing and installing an idler gear on a Caterpillar 299D2 XHP compact track loader. The removal procedure involves removing the front housing, ensuring the piston and gear timing marks are aligned, installing a flywheel stopper tool, and removing bolts and plates. The installation procedure specifies installing the idler gear in reverse order and tightening the bolts to the specified torque.
Similar to Caterpillar Cat 299D2 COMPACT TRACK LOADER (Prefix BY4) Service Repair Manual Instant Download.pdf (15)
Caterpillar Cat 329D2 and 329D2L Excavator (Prefix RGA) Service Repair Manual...gongfuao7509
The document provides instructions for disassembling and assembling a swing motor and swing drive. Key steps include:
1. Cleaning all parts thoroughly before assembly and applying a light film of hydraulic oil.
2. Using retaining ring pliers to install a retaining ring and assembling plates, pistons, a barrel and other components into the motor housing in the specified order.
3. Attaching lifting brackets and safely lifting the heavy swing motor or drive components during removal and installation procedures.
Caterpillar Cat 329D and 329D L Excavator (Prefix DTZ) Service Repair Manual ...gongfuao7509
This document provides instructions for removing and installing the water temperature regulator on a Caterpillar C7 engine. It describes:
1. Draining the engine coolant below the level of the water temperature regulator.
2. Disconnecting the hose from the regulator cover and removing mounting bolts.
3. Installing the new regulator by reversing the removal steps, filling the cooling system, and tightening all connections to the specified torques.
Cleanliness is important to prevent contamination, and safety precautions are described for working with hot coolant and steam.
Caterpillar Cat 326F L Excavator (Prefix WGL) Service Repair Manual Instant D...gongfuao7509
This document provides instructions to disassemble a travel motor. It begins by having the technician remove the travel motor and attach it to assembly tools. It then lists 28 steps to fully disassemble the travel motor by removing components like caps, springs, seals, plates and housing assemblies. Safety notices are included throughout to warn of potential injury from released spring forces.
Caterpillar Cat 324E L Excavator (Prefix PNW) Service Repair Manual Instant D...gongfuao7509
This document provides instructions for disassembling and assembling the travel motor of a 324E L Excavator. It lists the required tools and parts and provides 28 steps to disassemble the travel motor by removing components like the head, O-rings, springs, brake piston, plates, and bearings. It then lists 19 steps to assemble the travel motor by reinstalling these components in the reverse order, noting proper lubrication and alignment of parts.
This document provides instructions for removing and installing various engine components on a Caterpillar 324D LN excavator. It includes procedures for removing and installing the front cover, front housing, camshaft idler gear, valve mechanism cover, valve mechanism cover base, rocker shaft and pushrods. The document provides illustrations and specifies required tools for each procedure. Safety notices are included to keep parts clean and contain fluids.
Caterpillar Cat 324D FM LL EXCAVATOR (Prefix JLS) Service Repair Manual Insta...gongfuao7509
This document provides instructions for disassembling and assembling the final drive of a 324D FM LL EXCAVATOR. It outlines 21 steps for disassembly, which include removing plates, springs, pistons, gears, and other components. It also outlines 16 steps for assembly, which include installing bearings, seals, gears, and other components back into the final drive housing using various tools. The document includes illustrations to supplement the written instructions.
Caterpillar Cat 323F SA and 323F LN Excavator (Prefix FA2) Service Repair Man...gongfuao7509
This document provides instructions for disassembling and assembling the final drive of an excavator model 323F SA. It lists 30 steps to disassemble the final drive by removing components like the cover, carrier assembly, ring gears, and seals. It then lists 31 steps to reassemble the final drive by installing components like bearings, seals, gears, and shims in the reverse order of disassembly. Precise tools and procedures are required due to the heavy weight and precision fitting of components.
Caterpillar Cat 323D2 and 323D2 L Excavator (Prefix JEX) Service Repair Manua...gongfuao7509
The document provides instructions for disassembling the final drive of an excavator model 323D2. It involves 33 steps including removing the final drive cover, carrier assembly, ring gears, and other components. Various tools are required including a transmission repair stand, link brackets, forcing screws, and puller assembly. Cleanliness is important to prevent dirt from entering internal parts during disassembly.
Caterpillar Cat 322C FM EXCAVATOR (Prefix CAM) Service Repair Manual Instant ...gongfuao7509
The document provides instructions for removing the engine oil filter base from a 322C FM excavator with a 3126 engine. The procedure involves first removing the turbocharger. Then, using a strap wrench, loosen the oil filter base by turning it counterclockwise. Finally, clean the oil filter base mounting surface before installing the new oil filter base. The summary is provided in 3 sentences or less as requested.
Caterpillar Cat 322C FM EXCAVATOR (Prefix C3R) Service Repair Manual Instant ...gongfuao7509
1. The document provides instructions for removing and installing the unit injector hydraulic pump and turbocharger on a Caterpillar 3126B engine.
2. The unit injector hydraulic pump removal instructions include disconnecting lines and harness, removing mounting bolts, and inspecting seals. Installation is the reverse of removal.
3. Turbocharger removal requires removing bolts and nuts connecting it to the exhaust manifold and disconnecting oil lines. Disassembly separates the housing components. Assembly reconnects the parts and installation bolts the turbocharger back into place.
Caterpillar Cat 322C FM EXCAVATOR (Prefix BPH) Service Repair Manual Instant ...gongfuao7509
This document provides instructions for removing and installing a governor from a 322C FM excavator engine. The removal procedure involves disconnecting fuel and oil lines, removing retaining clips and bolts, and using special tools to remove the governor. The installation procedure outlines cleaning and lubricating parts, replacing seals, and using tools to install the governor along with associated lines, pins, and clips. Precautions are given to keep parts clean and ensure free movement of components.
Caterpillar Cat 322B L EXCAVATOR (Prefix 5CR) Service Repair Manual Instant D...gongfuao7509
This document provides instructions for removing and installing the bucket linkage group and bucket cylinder on a Caterpillar 322B L excavator. The procedures include removing pins and bolts to separate the various linkage and cylinder components, as well as instructions for installing replacement components and adjusting clearances using shims. Proper lubrication of pins, bolts and other components is emphasized during assembly.
Caterpillar Cat 322B L EXCAVATOR (Prefix 1YS) Service Repair Manual Instant D...gongfuao7509
This document provides instructions for removing and installing the governor and associated components on a Caterpillar 3116 engine. The removal process involves disconnecting linkages and tubes, removing mounting bolts and clips, and using specialized tools. The installation follows the removal steps in reverse, applying lubricant to seals and ensuring proper adjustment of linkages. Required tools include various pliers and pin tools to facilitate disconnecting and reconnecting components.
Caterpillar Cat 322 L EXCAVATOR (Prefix 9RL) Service Repair Manual Instant Do...gongfuao7509
This document provides instructions for removing and installing a governor from a Caterpillar Cat 322 L excavator powered by a 3116 engine. The removal procedure involves disconnecting tubes, removing clips and bolts, and using special tools. The installation procedure describes cleaning and lubricating parts, replacing seals, and using tools to install the governor components in reverse order of removal. Proper torque specifications and checks are listed to ensure correct installation.
This document provides instructions for servicing the air conditioning system on Caterpillar 322 and 322L excavators. It describes safety precautions when working with refrigerant due to risks of injury. The document outlines procedures for preparing the machine, removing and installing various AC system components like lines, the compressor, and preparing the system for disassembly and reassembly. Detailed steps are provided for correctly assembling refrigerant line fittings and other components.
Caterpillar Cat 320F L Excavator (Prefix YBM) Service Repair Manual Instant D...gongfuao7509
The document provides instructions for removing and installing a boom cylinder on an excavator. Key steps include:
1. Lowering the boom and releasing hydraulic pressure before removal.
2. Detaching hoses and removing bolts and pins to separate the cylinder from the excavator.
3. Lifting the cylinder, which weighs approximately 287kg, off the excavator using slings.
4. Reinstalling involves lifting the cylinder back into place with slings, reattaching with bolts and pins, and reconnecting hoses. Torque specifications are provided for all fasteners.
This document provides instructions for removing and installing a flywheel on a 320E LRR excavator with a C6.6 engine. The removal procedure involves using guide studs and lifting equipment to support the flywheel, then removing mounting bolts. The installation procedure specifies cleaning and inspecting components, positioning the flywheel with guide studs and lifting equipment, and tightening mounting bolts to the specified torque. Instructions are also provided for removing and installing a crankshaft rear seal.
This document provides instructions for removing and installing various engine components on a Caterpillar 320E LRR excavator, including:
1. Removing and installing the crankshaft front seal using specific tools.
2. Removing and installing the front cover, which requires removing bolts in a specific order and position.
3. Installing a new gasket and front seal when reinstalling the front cover.
The document contains detailed step-by-step instructions and illustrations for performing maintenance on the engine's crankshaft pulley, vibration damper, front seal, and front cover. Precautions are provided to keep parts clean and torque specifications are given.
This document provides instructions for disassembling and assembling the gear pump (pilot) and main hydraulic pump on a Caterpillar 320D2 excavator. The summary includes steps to disassemble the gear pump by removing housing bolts, seals, gears, and plates. It also describes removing the main hydraulic pump by disconnecting hoses and harnesses, removing mounting bolts, and lifting out the pump along with attached auxiliary pumps and pilots.
The document provides instructions for disassembling and assembling the travel motor of a 320D2L excavator. It describes 27 steps to disassemble the travel motor by removing components like the head, check valves, fittings, pistons, plates, seals and more. It then describes 25 steps to reassemble the travel motor, replacing components in the reverse order and ensuring proper alignment of parts like keys and cam plates. Special care must be taken to avoid damaging parts and keep components matched during assembly.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: COMPACT TRACK LOADER
Model: 299D2 COMPACT TRACK LOADER BY4
Configuration: 299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWERED BY C3.8 Engine
Disassembly and Assembly
C3.8 Engines for Caterpillar Built Machines
Media Number -UENR0129-08 Publication Date -01/09/2015 Date Updated -19/05/2016
i04664023
Flywheel - Install
SMCS - 1156-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-7994 Guide Bolt 2
Always wear protective gloves when handling parts that have been
heated.
1/4
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g02797127
Typical example
1. If the ring gear was removed, follow Steps 1.a through 1.c to install ring gear (7) to flywheel
(8).
a. Identify the orientation of the new ring gear in order to install the ring gear correctly
onto the flywheel.
Note: The chamfered side of gear teeth (Y) must face toward the starting motor when
the flywheel is installed. This will ensure the correct engagement of the starting
motor.
b. Heat ring gear (3) in an oven to a maximum temperature of 150°C (302°F) prior to
installation.
Note: Do not use a torch to heat the ring gear.
c. Ensure that the orientation of ring gear (7) is correct and quickly install the ring gear
onto flywheel (8).
Illustration 2 g02797120
2/4
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 2. Thoroughly clean the flywheel housing. Inspect the crankshaft rear seal for leaks. If there
are any oil leaks replace the crankshaft rear seal. Refer to Disassembly and Assembly,
"Crankshaft Rear Seal - Remove and Install".
3. Install Tooling (A) on the crankshaft.
4. Use a suitable lifting device to position flywheel assembly (5). The weight of flywheel
assembly (5) is approximately 23 kg (50 lb).
5. Align flywheel assembly (5) with Tooling (A). Install flywheel assembly (5) to the
crankshaft.
Note: Ensure the correct orientation of the flywheel on the crankshaft.
6. Apply clean engine oil onto bolts (6). Install bolts (6) finger tight.
7. Remove Tooling (A) and install the two remaining bolts (6).
8. Remove the lifting device from the flywheel.
9. Use a suitable tool to prevent flywheel assembly (5) from rotating. Tighten bolts (6) to a
torque of 98.1 to 107 N·m (72 to 79 lb ft).
10. Check the concentricity of the flywheel. Refer to Systems Operation, Testing and Adjusting,
"Flywheel - Inspect".
Illustration 3 g02797118
11. Install pump coupling (4). Install bolts (3).
3/4
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 4 g02797115
12. Install cover (2). Install bolts (1).
End By:
a. Install the starting motor.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 30 23:51:46 UTC+0800 2019
4/4
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: COMPACT TRACK LOADER
Model: 299D2 COMPACT TRACK LOADER BY4
Configuration: 299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWERED BY C3.8 Engine
Disassembly and Assembly
C3.8 Engines for Caterpillar Built Machines
Media Number -UENR0129-08 Publication Date -01/09/2015 Date Updated -19/05/2016
i04664019
Crankshaft Rear Seal - Remove and Install
SMCS - 1161-010
Removal Procedure
Start By:
a. Remove the flywheel.
Illustration 1 g02797554
1. Drill three holes in lip seal (1). Use a suitable slide hammer to remove lip seal (1).
2. Remove ring seal (2).
Installation Procedure
Table 1
Required Tools
1/2
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Tool Part Number Part Description Qty
A 393-2571 Driver 1
Illustration 2 g02797554
Illustration 3 g02870418
1. Use Tooling (A) to install ring seal (2).
2. Use Tooling (A) to install lip seal (1).
End By:
a. Install the flywheel.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 30 23:52:42 UTC+0800 2019
2/2
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Shutdown SIS
Previous Screen
Product: COMPACT TRACK LOADER
Model: 299D2 COMPACT TRACK LOADER BY4
Configuration: 299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWERED BY C3.8 Engine
Disassembly and Assembly
C3.8 Engines for Caterpillar Built Machines
Media Number -UENR0129-08 Publication Date -01/09/2015 Date Updated -19/05/2016
i04839813
Crankshaft Rear Seal Carrier - Remove and Install
SMCS - 1161-010-C3
Removal Procedure
1. Refer to Specifications, "Crankshaft".
Illustration 1 g02869998
2. Remove bolts (1). Use two of bolts (1) to remove bearing case cover (2) .
1/3
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 2 g02870025
3. Remove lip seal (3) from bearing case cover (2) .
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 393-2571 Seal Installer 1
B - Three Bond 1217H -
Illustration 3 g02870025
2/3
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 4 g02870418
1. Use Tooling (A) to install lip seal (3) into bearing case cover (2) .
Illustration 5 g02869998
2. Apply Tooling (B) onto the mating surface of bearing case cover (2). Apply clean engine oil
onto the lip seal. Install bearing case cover (2) .
3. Install bolts (1). Tighten bolts (1) to a torque of 25.5 ± 1.5 N·m (18.8 ± 1.1 lb ft).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 30 23:53:38 UTC+0800 2019
3/3
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: COMPACT TRACK LOADER
Model: 299D2 COMPACT TRACK LOADER BY4
Configuration: 299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWERED BY C3.8 Engine
Disassembly and Assembly
C3.8 Engines for Caterpillar Built Machines
Media Number -UENR0129-08 Publication Date -01/09/2015 Date Updated -19/05/2016
i06272842
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 439-3938 Link Bracket 2
B - Three Bond1217H 1
Start By:
a. Remove the bearing case cover.
Illustration 1 g02797548
1/2
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. 1. Attach Tooling (A) and a suitable lifting device onto flywheel housing (1). The weight of
flywheel housing (1) is approximately 45 kg (100 lb).
2. Remove bolts (2) and bolts (3). Remove flywheel housing (1).
Installation Procedure
1. Install flywheel housing (1) in the reverse order of removal.
a. Apply Tooling (B) onto the mating surface of flywheel housing (1).
b. For the SSL, MTL, and CTL models that end in D2 models (BL2, MD2, BL7, HP2,
FD2, DX2, DX9, and BY4), tighten bolts (3) and bolts (2) to a torque of
103 ± 14 N·m (76 ± 10 lb ft).
c. For all other models, tighten bolts (3) and bolts (2) to a torque of 78 ± 12 N·m
(56 ± 9 lb ft).
d. Refer to Systems Operation, Testing and Adjusting, "Flywheel Housing - Inspect".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 30 23:54:34 UTC+0800 2019
2/2
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: COMPACT TRACK LOADER
Model: 299D2 COMPACT TRACK LOADER BY4
Configuration: 299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWERED BY C3.8 Engine
Disassembly and Assembly
C3.8 Engines for Caterpillar Built Machines
Media Number -UENR0129-08 Publication Date -01/09/2015 Date Updated -19/05/2016
i04664013
Crankshaft Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 393-2572 Flywheel Stopper 1
Start By:
a. Remove the belt.
1. Install Tooling (A) onto the flywheel.
Illustration 1 g02860756
2. Remove bolt (1) to remove pulley (2).
1/2
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Installation Procedure
1. Install pulley (2) in the reverse order of removal.
a. Apply clean engine oil onto bolt (1).
b. Tighten bolt (1) to a torque of 264.5 ± 9.5 N·m (195.1 ± 7.0 lb ft).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 30 23:55:29 UTC+0800 2019
2/2
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: COMPACT TRACK LOADER
Model: 299D2 COMPACT TRACK LOADER BY4
Configuration: 299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWERED BY C3.8 Engine
Disassembly and Assembly
C3.8 Engines for Caterpillar Built Machines
Media Number -UENR0129-08 Publication Date -01/09/2015 Date Updated -19/05/2016
i04664010
Crankshaft Front Seal - Remove and Install
SMCS - 1160-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-8145 Drill Bit (4.10 mm) 1
B 1U-7600 Slide Hammer Puller 1
Start By:
a. Remove the crankshaft pulley.
NOTICE
Ensure that the main lip is used in order to remove the crankshaft
front seal. Do not damage the edge of the housing for the crankshaft
front seal.
1/3
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 1 g02860787
1. Use Tooling (A) to drill three evenly spaced holes in crankshaft front seal (1).
2. Use Tooling (B) to carefully remove crankshaft front seal (1). Alternate the position of
Tooling (B) from one hole to another hole to allow the crankshaft front seal to be removed.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
C 393-2570 Seal Installer 1
Illustration 2 g02860787
2/3
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 3 g02866181
1. Lubricate the outside diameter of a new crankshaft front seal (1) with clean engine oil. Use
Tooling (C) to install crankshaft front seal (1).
2. Apply clean engine oil to the lip of crankshaft front seal (1).
End By:
a. Install the crankshaft pulley.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 30 23:56:25 UTC+0800 2019
3/3
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: COMPACT TRACK LOADER
Model: 299D2 COMPACT TRACK LOADER BY4
Configuration: 299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWERED BY C3.8 Engine
Disassembly and Assembly
C3.8 Engines for Caterpillar Built Machines
Media Number -UENR0129-08 Publication Date -01/09/2015 Date Updated -19/05/2016
i04801361
Idler Gear - Remove and Install
SMCS - 1206
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 393-2572 Flywheel Stopper 1
B 393-2573 Driver 1
Start By:
a. Remove the front housing.
1. Ensure that number four piston is at the top center position on the compression stroke. Refer
to Systems Operation, Testing and Adjusting, "Finding Top Center Position for No. 4
Piston".
1/3
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 1 g02871716
2. Ensure that timing marks on the gears are aligned.
Alternatively, make temporary timing marks on the gears in order to show alignment.
3. Install Tooling (A) onto the flywheel. Remove bolts (1) and plate (2).
Illustration 2 g02872045
4. Remove idler gear (3), shaft (4), and plate (5).
2/3
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 3 g02920337
5. Use Tooling (B) to remove bushing (6) from idler gear (3).
Installation Procedure
1. Install idler gear (3) in the reverse order of removal.
a. Apply clean engine oil onto the bore of idler gear (3) and bushing (6).
b. Ensure that edge of bushing (6) is flush with the edge of the bore that is in idler gear
(3).
c. Tighten bolts (1) to a torque of 25.5 ± 1.5 N·m (18.8 ± 1.1 lb ft).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 30 23:57:21 UTC+0800 2019
3/3
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: COMPACT TRACK LOADER
Model: 299D2 COMPACT TRACK LOADER BY4
Configuration: 299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWERED BY C3.8 Engine
Disassembly and Assembly
C3.8 Engines for Caterpillar Built Machines
Media Number -UENR0129-08 Publication Date -01/09/2015 Date Updated -19/05/2016
i06662240
Idler Gear - Remove and Install
SMCS - 1206
S/N - BL21-UP
S/N - BL71-UP
S/N - BY41-UP
S/N - DX21-UP
S/N - DX91-UP
S/N - FD21-UP
S/N - HP21-UP
S/N - MD21-UP
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 393-2572 Flywheel Stopper 1
Start By:
a. Remove the front housing.
1. Ensure that number four piston is at the top center position on the compression stroke. Refer
to Systems Operation, Testing and Adjusting, "Finding Top Center Position for No. 4
Piston".
1/2
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
23. Illustration 1 g06066040
2. Ensure that timing marks on the gears are aligned.
Alternatively, make temporary timing marks on the gears to show alignment.
3. Install Tooling (A) onto the flywheel. Remove bolts (2) and idler gear (3).
4. Remove nuts (1) and idler gear (4).
Installation Procedure
1. Install the idler gears in the reverse order of removal.
a. Tighten nuts (1) to a torque of 24 N·m to 27 N·m (212 lb in to 239 lb in).
b. Tighten bolts (2) to a torque of 24 N·m to 27 N·m (212 lb in to 239 lb in).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 30 23:58:16 UTC+0800 2019
2/2
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...