The document provides instructions for removing and installing various engine components on a Caterpillar C3.8 engine, including:
- Installing the flywheel, ensuring the ring gear is oriented correctly
- Removing and installing the crankshaft rear seal and carrier
- Removing and installing the flywheel housing
- Removing and installing the crankshaft pulley
The procedures include lists of required tools and step-by-step instructions accompanied by illustrations. Safety and installation notes are also provided.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 compact track loader, including:
- Removing and installing the flywheel, which involves cleaning surfaces, heating the ring gear, and torquing bolts to a specified value.
- Removing and installing the crankshaft rear seal, which involves drilling holes, using a slide hammer, and pressing in new seals.
- Removing and installing the crankshaft rear seal carrier, bearing case cover, and lip seal using seal installation tools and threadlocker.
- Removing and installing the flywheel housing, which requires lifting equipment and torquing bolts to a specified value.
-
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 compact track loader, including:
- Removing and installing the flywheel, which involves cleaning surfaces, heating the ring gear, and torquing bolts to a specified value.
- Removing and installing the crankshaft rear seal, which involves drilling holes, using a slide hammer, and pressing in new seals.
- Removing and installing the crankshaft rear seal carrier, bearing case cover, and lip seal using seal installation tools and threadlocker.
- Removing and installing the flywheel housing, which requires lifting equipment and torquing bolts to a specified value.
-
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 Compact Track Loader, including:
- Flywheel installation which requires cleaning surfaces, heating the ring gear, and torquing bolts to a specified value.
- Crankshaft rear seal replacement involving removing the old seal and pressing in a new one using specific tools.
- Removing and installing the flywheel housing which requires attaching lifting brackets and torquing bolts to a specified value.
- Procedures for the crankshaft pulley, front seal, and bearing case cover that include cleaning, applying oil, and ensuring proper torque on fasteners.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 Compact Track Loader, including:
- Flywheel installation which requires cleaning surfaces, heating the ring gear, and torquing bolts to a specified value.
- Crankshaft rear seal replacement involving removing the old seal and pressing in a new one using specific tools.
- Removing and installing the flywheel housing which requires attaching lifting equipment and torquing bolts to a specified value.
- Procedures for the crankshaft pulley, front seal, and bearing case cover that include cleaning, applying oil, and ensuring proper orientation of parts.
The document provides instructions to remove and install the valve mechanism cover on a Caterpillar C3.8 engine. The removal procedure involves disconnecting wire harnesses, tubes, and bolts. The cover and gasket are then removed. Installation is the reverse of removal, requiring reinstallation of the cover, gasket, bolts, wires, and tubes. Bolts and nuts are tightened to specified torque values.
The document provides instructions to remove and install the valve mechanism cover on a Caterpillar C3.8 engine. The removal procedure involves disconnecting wire harnesses, tubes, and bolts. The cover and gasket are then removed. Installation is the reverse of removal, requiring reinstallation of the cover and gaskets and tightening of bolts and nuts to the specified torques.
The document provides instructions to remove and install the valve mechanism cover on a Caterpillar C3.8 engine. The removal procedure involves disconnecting wire harnesses, tubes, and bolts. The cover and gasket are then removed. Installation is the reverse of removal, requiring reinstallation of the cover, gasket, bolts, wires and tubes. Bolts and nuts are tightened to specified torque values.
The document provides instructions for removing and installing an idler gear on a Caterpillar 299D2 XHP compact track loader. The removal procedure involves removing the front housing, ensuring the piston is at top center position, marking gear alignment, installing a flywheel stopper tool, and removing bolts, plates and the idler gear. The installation procedure specifies cleaning and applying oil to parts, ensuring correct bushing alignment, and tightening bolts to the specified torque.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 compact track loader, including:
- Removing and installing the flywheel, which involves cleaning surfaces, heating the ring gear, and torquing bolts to a specified value.
- Removing and installing the crankshaft rear seal, which involves drilling holes, using a slide hammer, and pressing in new seals.
- Removing and installing the crankshaft rear seal carrier, bearing case cover, and lip seal using seal installation tools and threadlocker.
- Removing and installing the flywheel housing, which requires lifting equipment and torquing bolts to a specified value.
-
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 compact track loader, including:
- Removing and installing the flywheel, which involves cleaning surfaces, heating the ring gear, and torquing bolts to a specified value.
- Removing and installing the crankshaft rear seal, which involves drilling holes, using a slide hammer, and pressing in new seals.
- Removing and installing the crankshaft rear seal carrier, bearing case cover, and lip seal using seal installation tools and threadlocker.
- Removing and installing the flywheel housing, which requires lifting equipment and torquing bolts to a specified value.
-
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 Compact Track Loader, including:
- Flywheel installation which requires cleaning surfaces, heating the ring gear, and torquing bolts to a specified value.
- Crankshaft rear seal replacement involving removing the old seal and pressing in a new one using specific tools.
- Removing and installing the flywheel housing which requires attaching lifting brackets and torquing bolts to a specified value.
- Procedures for the crankshaft pulley, front seal, and bearing case cover that include cleaning, applying oil, and ensuring proper torque on fasteners.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 Compact Track Loader, including:
- Flywheel installation which requires cleaning surfaces, heating the ring gear, and torquing bolts to a specified value.
- Crankshaft rear seal replacement involving removing the old seal and pressing in a new one using specific tools.
- Removing and installing the flywheel housing which requires attaching lifting equipment and torquing bolts to a specified value.
- Procedures for the crankshaft pulley, front seal, and bearing case cover that include cleaning, applying oil, and ensuring proper orientation of parts.
The document provides instructions to remove and install the valve mechanism cover on a Caterpillar C3.8 engine. The removal procedure involves disconnecting wire harnesses, tubes, and bolts. The cover and gasket are then removed. Installation is the reverse of removal, requiring reinstallation of the cover, gasket, bolts, wires, and tubes. Bolts and nuts are tightened to specified torque values.
The document provides instructions to remove and install the valve mechanism cover on a Caterpillar C3.8 engine. The removal procedure involves disconnecting wire harnesses, tubes, and bolts. The cover and gasket are then removed. Installation is the reverse of removal, requiring reinstallation of the cover and gaskets and tightening of bolts and nuts to the specified torques.
The document provides instructions to remove and install the valve mechanism cover on a Caterpillar C3.8 engine. The removal procedure involves disconnecting wire harnesses, tubes, and bolts. The cover and gasket are then removed. Installation is the reverse of removal, requiring reinstallation of the cover, gasket, bolts, wires and tubes. Bolts and nuts are tightened to specified torque values.
The document provides instructions for removing and installing an idler gear on a Caterpillar 299D2 XHP compact track loader. The removal procedure involves removing the front housing, ensuring the piston is at top center position, marking gear alignment, installing a flywheel stopper tool, and removing bolts, plates and the idler gear. The installation procedure specifies cleaning and applying oil to parts, ensuring correct bushing alignment, and tightening bolts to the specified torque.
The document provides instructions for removing and installing an idler gear on a Caterpillar 299D2 XHP compact track loader. The removal procedure involves removing the front housing, ensuring the piston is at top center position, marking timing gear alignment, installing a flywheel stopper tool, and removing bolts and plates. The installation procedure specifies cleaning and applying oil to parts, ensuring correct bushing alignment, and torquing bolts to the specified values.
The document provides instructions for removing and installing an idler gear on a Caterpillar 299D2 XHP compact track loader. The removal procedure involves removing the front housing, ensuring the piston is at top center position, marking timing gear alignment, installing a flywheel stopper tool, and removing bolts and plates. The installation procedure specifies cleaning and applying oil to parts, ensuring correct bushing alignment, and torquing bolts to the specified values.
The document provides instructions for removing and installing an idler gear on a Caterpillar 299D2 XHP compact track loader. The removal procedure involves removing the front housing, ensuring the piston is at top center position, marking gear alignment, installing a flywheel stopper tool, and removing bolts, plates and the idler gear. The installation procedure specifies cleaning and applying oil to parts, ensuring correct bushing alignment, and tightening bolts to the specified torque.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 XHP compact track loader. The procedures include removing the idler gear by first ensuring the engine is at top center position and removing bolts. Other removal procedures include the front housing, fumes disposal filter, valve mechanism cover and related components. Reinstallation is done in reverse order, applying oil and torquing bolts to the specified values.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 XHP compact track loader. The procedures include removing the idler gear by first ensuring the engine is at top center position and removing bolts. Other removal procedures include the front housing, fumes disposal filter, and valve mechanism cover. Reinstallation is done by reversing the removal steps and tightening bolts to the specified torques.
The document provides instructions to remove and install a valve mechanism cover on a Caterpillar C3.8 engine. It describes:
1. Disconnecting various tubes, harnesses, and hoses attached to the cover.
2. Removing bolts to take off the cover and gasket.
3. Cleaning and inspecting the mating surfaces before installing the new cover in reverse order using specified torques for the bolts.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 XHP compact track loader. The procedures include removing the idler gear by first ensuring the engine is at top center position and removing bolts, nuts and plates. The front housing is removed by disconnecting wiring harnesses and belts, removing bolts, and using a flywheel stopper tool. The fumes disposal filter is removed by disconnecting hoses and removing a bolt and bracket.
The document provides instructions to remove and install a valve mechanism cover on a Caterpillar C3.8 engine. It describes:
1. Disconnecting various tubes, harnesses, and hoses attached to the cover.
2. Removing bolts to take off the cover and gasket.
3. Cleaning and inspecting the mating surfaces before installing the new cover in reverse order using specified torques for the bolts.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 XHP compact track loader. The procedures include removing the idler gear by first ensuring the engine is at top center position and removing bolts, nuts and plates. The front housing is removed by disconnecting wiring harnesses and belts, removing bolts, and using a flywheel stopper tool. The fumes disposal filter is removed by disconnecting hoses and removing a bolt and bracket.
The document provides instructions to remove and install a valve mechanism cover on a Caterpillar C3.8 engine. It describes:
1. Disconnecting various tubes, harnesses, and hoses attached to the cover.
2. Removing bolts to take off the cover and gasket.
3. Cleaning and inspecting the mating surfaces before installing the new cover in reverse order using specified torques for the bolts.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 XHP compact track loader. The procedures include removing the idler gear by first ensuring the engine is at top center position and removing bolts. Other removal procedures include the front housing, fumes disposal filter, valve mechanism cover and related components. Reinstallation is done by reversing the removal steps and tightening bolts to the specified torques.
The document provides instructions for removing and installing an idler gear on a Caterpillar 299D2 XHP compact track loader. The removal procedure involves removing the front housing, ensuring the piston and gear timing marks are aligned, installing a flywheel stopper tool, and removing bolts and plates. The installation procedure specifies reversing the removal steps and tightening bolts to the specified torque values.
The document provides instructions for removing and installing an idler gear on a Caterpillar 299D2 XHP compact track loader. The removal procedure involves removing the front housing, ensuring the piston and gear timing marks are aligned, installing a flywheel stopper tool, and removing bolts and plates. The installation procedure specifies cleaning and lubricating parts, ensuring the bushing is flush, and tightening bolts to the specified torque.
The document provides instructions for removing and installing an idler gear on a Caterpillar 299D2 XHP compact track loader. The removal procedure involves removing the front housing, ensuring the piston and gear timing marks are aligned, installing a flywheel stopper tool, and removing bolts and plates. The installation procedure specifies cleaning and lubricating parts, ensuring components are flush, and tightening bolts to the specified torque using a flywheel stopper tool.
The document provides instructions for removing and installing an idler gear on a Caterpillar 299D2 XHP compact track loader. The removal procedure involves removing the front housing, ensuring the piston and gear timing marks are aligned, installing a flywheel stopper tool, and removing bolts and plates. The installation procedure specifies installing the idler gear in reverse order and tightening the bolts to the specified torque.
CASE IH Rowtrac 370 Tier 4B (final) Tractor Service Repair Manual.pdff8usejkddmmd
This document is a service manual for Case IH tractors and covers safety rules, engine systems, transmission systems, front and rear axle systems, power take-off systems, brakes and controls, hydraulic systems, hitches and couplings, frames and ballasting, steering systems, wheels, tracks and suspensions, cab climate control, electrical systems, and bodywork. It provides maintenance and repair instructions for qualified service personnel.
CASE IH Quadtrac 620 Tier 4B (final) Tractor Service Repair Manual.pdff8usejkddmmd
This document is a service manual for Case IH Rowtrac, Steiger, and Quadtrac tractors from model years 2014 and up that meet Tier 4B emissions standards. It contains sections covering the engine, transmission, front and rear axle systems, power take-off, brakes and controls, hydraulic systems, hitches and couplings, frames and ballasting, steering, wheels, tracks and suspensions, cab climate control, and electrical systems. Each section provides information and specifications to service and repair the components.
CASE IH Quadtrac 580 Tier 4B (final) Tractor Service Repair Manual.pdff8usejkddmmd
This document is a service manual for Case IH Rowtrac, Steiger, and Quadtrac tractors from model years 2014 and up that meet Tier 4B emissions standards. It contains sections covering the engine, transmission, front and rear axle systems, power take-off, brakes and controls, hydraulic systems, hitches and couplings, frames and ballasting, steering, wheels, tracks and suspensions, cab climate control, and electrical systems. Each section provides information and specifications to service and repair the components.
CASE IH Quadtrac 540 Tier 4B (final) Tractor Service Repair Manual.pdff8usejkddmmd
This document is a service manual for Case IH Rowtrac, Steiger, and Quadtrac tractors from model years 2014 and up that meet Tier 4B emissions standards. It contains information on the engine, transmission, front and rear axle systems, power take-off, brakes, hydraulic systems, frames, steering, wheels, tracks, cab climate control, and electrical systems. The manual is intended to assist technicians with servicing and repair.
CASE IH Quadtrac 500 Tier 4B (final) Tractor Service Repair Manual.pdff8usejkddmmd
This document is a service manual for Case IH Rowtrac, Steiger, and Quadtrac tractors from model years 2014 and up that meet Tier 4B emissions standards. It contains sections covering the engine, transmission, front and rear axle systems, power take-off, brakes and controls, hydraulic systems, hitches and couplings, frames and ballasting, steering, wheels, tracks and suspensions, cab climate control, and electrical systems. Each section provides information and specifications to service and repair the components.
CASE IH Quadtrac 470 Tier 4B (final) Tractor Service Repair Manual.pdff8usejkddmmd
This document is a service manual for Case IH Rowtrac, Steiger, and Quadtrac tractors from model years 2014 and up that meet Tier 4B emissions standards. It contains information on the engine, transmission, front and rear axle systems, power take-off, brakes, hydraulic systems, frames, steering, wheels, tracks, cab climate control, and electrical systems. The manual is intended to assist technicians with servicing and repairs.
CASE IH PUMA 210 Tractor Service Repair Manual.pdff8usejkddmmd
This document is a service manual that contains information on the distribution systems for a tractor model. It includes sections on the primary and secondary hydraulic power systems, hydraulic command system, pneumatic system, electrical and electronic systems. It provides information on special tools needed for maintenance and repair of components within these various systems.
More Related Content
Similar to Caterpillar Cat 299D2 COMPACT TRACK LOADER (Prefix BY4) Service Repair Manual (BY400001 and up).pdf
The document provides instructions for removing and installing an idler gear on a Caterpillar 299D2 XHP compact track loader. The removal procedure involves removing the front housing, ensuring the piston is at top center position, marking timing gear alignment, installing a flywheel stopper tool, and removing bolts and plates. The installation procedure specifies cleaning and applying oil to parts, ensuring correct bushing alignment, and torquing bolts to the specified values.
The document provides instructions for removing and installing an idler gear on a Caterpillar 299D2 XHP compact track loader. The removal procedure involves removing the front housing, ensuring the piston is at top center position, marking timing gear alignment, installing a flywheel stopper tool, and removing bolts and plates. The installation procedure specifies cleaning and applying oil to parts, ensuring correct bushing alignment, and torquing bolts to the specified values.
The document provides instructions for removing and installing an idler gear on a Caterpillar 299D2 XHP compact track loader. The removal procedure involves removing the front housing, ensuring the piston is at top center position, marking gear alignment, installing a flywheel stopper tool, and removing bolts, plates and the idler gear. The installation procedure specifies cleaning and applying oil to parts, ensuring correct bushing alignment, and tightening bolts to the specified torque.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 XHP compact track loader. The procedures include removing the idler gear by first ensuring the engine is at top center position and removing bolts. Other removal procedures include the front housing, fumes disposal filter, valve mechanism cover and related components. Reinstallation is done in reverse order, applying oil and torquing bolts to the specified values.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 XHP compact track loader. The procedures include removing the idler gear by first ensuring the engine is at top center position and removing bolts. Other removal procedures include the front housing, fumes disposal filter, and valve mechanism cover. Reinstallation is done by reversing the removal steps and tightening bolts to the specified torques.
The document provides instructions to remove and install a valve mechanism cover on a Caterpillar C3.8 engine. It describes:
1. Disconnecting various tubes, harnesses, and hoses attached to the cover.
2. Removing bolts to take off the cover and gasket.
3. Cleaning and inspecting the mating surfaces before installing the new cover in reverse order using specified torques for the bolts.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 XHP compact track loader. The procedures include removing the idler gear by first ensuring the engine is at top center position and removing bolts, nuts and plates. The front housing is removed by disconnecting wiring harnesses and belts, removing bolts, and using a flywheel stopper tool. The fumes disposal filter is removed by disconnecting hoses and removing a bolt and bracket.
The document provides instructions to remove and install a valve mechanism cover on a Caterpillar C3.8 engine. It describes:
1. Disconnecting various tubes, harnesses, and hoses attached to the cover.
2. Removing bolts to take off the cover and gasket.
3. Cleaning and inspecting the mating surfaces before installing the new cover in reverse order using specified torques for the bolts.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 XHP compact track loader. The procedures include removing the idler gear by first ensuring the engine is at top center position and removing bolts, nuts and plates. The front housing is removed by disconnecting wiring harnesses and belts, removing bolts, and using a flywheel stopper tool. The fumes disposal filter is removed by disconnecting hoses and removing a bolt and bracket.
The document provides instructions to remove and install a valve mechanism cover on a Caterpillar C3.8 engine. It describes:
1. Disconnecting various tubes, harnesses, and hoses attached to the cover.
2. Removing bolts to take off the cover and gasket.
3. Cleaning and inspecting the mating surfaces before installing the new cover in reverse order using specified torques for the bolts.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 XHP compact track loader. The procedures include removing the idler gear by first ensuring the engine is at top center position and removing bolts. Other removal procedures include the front housing, fumes disposal filter, valve mechanism cover and related components. Reinstallation is done by reversing the removal steps and tightening bolts to the specified torques.
The document provides instructions for removing and installing an idler gear on a Caterpillar 299D2 XHP compact track loader. The removal procedure involves removing the front housing, ensuring the piston and gear timing marks are aligned, installing a flywheel stopper tool, and removing bolts and plates. The installation procedure specifies reversing the removal steps and tightening bolts to the specified torque values.
The document provides instructions for removing and installing an idler gear on a Caterpillar 299D2 XHP compact track loader. The removal procedure involves removing the front housing, ensuring the piston and gear timing marks are aligned, installing a flywheel stopper tool, and removing bolts and plates. The installation procedure specifies cleaning and lubricating parts, ensuring the bushing is flush, and tightening bolts to the specified torque.
The document provides instructions for removing and installing an idler gear on a Caterpillar 299D2 XHP compact track loader. The removal procedure involves removing the front housing, ensuring the piston and gear timing marks are aligned, installing a flywheel stopper tool, and removing bolts and plates. The installation procedure specifies cleaning and lubricating parts, ensuring components are flush, and tightening bolts to the specified torque using a flywheel stopper tool.
The document provides instructions for removing and installing an idler gear on a Caterpillar 299D2 XHP compact track loader. The removal procedure involves removing the front housing, ensuring the piston and gear timing marks are aligned, installing a flywheel stopper tool, and removing bolts and plates. The installation procedure specifies installing the idler gear in reverse order and tightening the bolts to the specified torque.
Similar to Caterpillar Cat 299D2 COMPACT TRACK LOADER (Prefix BY4) Service Repair Manual (BY400001 and up).pdf (15)
CASE IH Rowtrac 370 Tier 4B (final) Tractor Service Repair Manual.pdff8usejkddmmd
This document is a service manual for Case IH tractors and covers safety rules, engine systems, transmission systems, front and rear axle systems, power take-off systems, brakes and controls, hydraulic systems, hitches and couplings, frames and ballasting, steering systems, wheels, tracks and suspensions, cab climate control, electrical systems, and bodywork. It provides maintenance and repair instructions for qualified service personnel.
CASE IH Quadtrac 620 Tier 4B (final) Tractor Service Repair Manual.pdff8usejkddmmd
This document is a service manual for Case IH Rowtrac, Steiger, and Quadtrac tractors from model years 2014 and up that meet Tier 4B emissions standards. It contains sections covering the engine, transmission, front and rear axle systems, power take-off, brakes and controls, hydraulic systems, hitches and couplings, frames and ballasting, steering, wheels, tracks and suspensions, cab climate control, and electrical systems. Each section provides information and specifications to service and repair the components.
CASE IH Quadtrac 580 Tier 4B (final) Tractor Service Repair Manual.pdff8usejkddmmd
This document is a service manual for Case IH Rowtrac, Steiger, and Quadtrac tractors from model years 2014 and up that meet Tier 4B emissions standards. It contains sections covering the engine, transmission, front and rear axle systems, power take-off, brakes and controls, hydraulic systems, hitches and couplings, frames and ballasting, steering, wheels, tracks and suspensions, cab climate control, and electrical systems. Each section provides information and specifications to service and repair the components.
CASE IH Quadtrac 540 Tier 4B (final) Tractor Service Repair Manual.pdff8usejkddmmd
This document is a service manual for Case IH Rowtrac, Steiger, and Quadtrac tractors from model years 2014 and up that meet Tier 4B emissions standards. It contains information on the engine, transmission, front and rear axle systems, power take-off, brakes, hydraulic systems, frames, steering, wheels, tracks, cab climate control, and electrical systems. The manual is intended to assist technicians with servicing and repair.
CASE IH Quadtrac 500 Tier 4B (final) Tractor Service Repair Manual.pdff8usejkddmmd
This document is a service manual for Case IH Rowtrac, Steiger, and Quadtrac tractors from model years 2014 and up that meet Tier 4B emissions standards. It contains sections covering the engine, transmission, front and rear axle systems, power take-off, brakes and controls, hydraulic systems, hitches and couplings, frames and ballasting, steering, wheels, tracks and suspensions, cab climate control, and electrical systems. Each section provides information and specifications to service and repair the components.
CASE IH Quadtrac 470 Tier 4B (final) Tractor Service Repair Manual.pdff8usejkddmmd
This document is a service manual for Case IH Rowtrac, Steiger, and Quadtrac tractors from model years 2014 and up that meet Tier 4B emissions standards. It contains information on the engine, transmission, front and rear axle systems, power take-off, brakes, hydraulic systems, frames, steering, wheels, tracks, cab climate control, and electrical systems. The manual is intended to assist technicians with servicing and repairs.
CASE IH PUMA 210 Tractor Service Repair Manual.pdff8usejkddmmd
This document is a service manual that contains information on the distribution systems for a tractor model. It includes sections on the primary and secondary hydraulic power systems, hydraulic command system, pneumatic system, electrical and electronic systems. It provides information on special tools needed for maintenance and repair of components within these various systems.
This document provides instructions for disassembling and assembling the travel motor of a 313D2 excavator. The disassembly process involves 27 steps to remove components like the motor head, brake piston, barrel assembly, springs and seals. The assembly process is outlined in 13 steps and provides details on cleaning, lubricating and installing components in the reverse order of disassembly. Special notes are provided regarding part orientations, identification marks and keys to ensure correct reassembly.
The document provides disassembly instructions for the final drive, travel motor, and various other components of 313D2 and 313D2 GC excavator models. It lists required tools and outlines multi-step procedures for removing parts like sprockets, valves, gears, plates, and seals. Safety notices warn of risks like fluid pressure, heavy component weights, and released spring forces during the disassembly process. Detailed illustrations supplement the text instructions.
Caterpillar Cat 313F L Excavator (Prefix NLG) Service Repair Manual (NLG00001...f8usejkddmmd
This document provides instructions for removing the front housing on a C4.4 engine. It involves:
1. Removing various other components first like the fan, pulley, oil pan, gears, and pump.
2. Disconnecting a harness, cutting a cable strap, and removing bolts to detach a bypass tube.
3. Removing bolts of different lengths to separate the front housing from the engine. Care must be taken to properly contain fluids.
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists over 30 detailed steps to disassemble components like the final drive, travel motor barrel assembly, planetary gear assembly, counterbalance valve housing assembly, and more. Safety notices are provided throughout to warn of hazards like released spring forces, hot or pressurized components, and ensuring fluids are contained. Required specialty tools are listed at the start for tasks like removing bearings, pistons, and other parts.
The document provides disassembly instructions for the final drive, travel motor, and various other components of 313D2 and 313D2 GC excavator models. It lists required tools and outlines multi-step procedures for removing parts like sprockets, valves, gears, plates, and seals. Safety notices warn of risks like fluid pressure, heavy component weights, and released spring forces during the disassembly process. Detailed illustrations supplement the text instructions.
This document provides instructions for removing the front housing on a C4.4 engine. It involves:
1. Removing various other components first like the fan, crankshaft pulley, oil pan, accessory drive, water pump and timing gears.
2. Disconnecting a harness assembly and removing bolts that secure a bypass tube to the front housing.
3. Removing bolts of various lengths that secure the front housing, and then removing the front housing from the engine.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 16 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 15 steps to disassemble the counterbalance valve. Safety notices are included regarding releasing pressures and springs.
This document provides instructions for disassembling the final drive, travel motor, and various other components of a 313D2 excavator. It lists the required tools and safety precautions and then outlines 16 steps to disassemble parts like the final drive, traction control valve, counterbalance valve, travel motor, and barrel assembly. Detailed illustrations are provided to identify specific components as they are removed.
CASE IH PUMA 195 Tractor Service Repair Manual.pdff8usejkddmmd
This document is a service manual for Case IH PUMA tractors that contains sections covering the tractor's distribution systems, power systems (primary hydraulic, secondary hydraulic, pneumatic, electrical), electronic systems, power production systems (engine, fuel injection, air intake, exhaust, cooling, lubrication, starting), powertrain (transmission, reducers, PTOs), travelling systems (axles, steering, brakes, suspension, wheels), body and structure, user platform, environment control, and working arm/hitch. The introduction provides safety rules for working on the tractor.
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists required tools and outlines 15 steps to disassemble the final drive, including draining oil and removing sprockets, valves, and bearings. It then details 19 steps to disassemble the travel motor, removing seals, plates, pistons, and the barrel assembly. Safety cautions are provided throughout regarding contained fluids, pressurized components, and released spring forces.
The document provides instructions for removing and installing various engine components on a Caterpillar 313D excavator. Specifically, it details procedures for removing and installing the flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear from the front gear group. The instructions include lists of required tools and step-by-step processes with illustrations for each procedure.
This document provides instructions for disassembling the final drive, travel motor, and counterbalance valve of a 313D excavator. It lists the required tools and outlines 20 steps to disassemble the components. These include draining fluids, removing covers, plates, seals, springs, pistons, and other parts. Safety precautions are provided to warn of potential injuries from parts propelled by springs or pressurized hydraulic fluid.
Caterpillar Cat 312D2 L Excavator (Prefix MPP) Service Repair Manual (MPP0000...f8usejkddmmd
This document provides instructions for disassembling various components of an excavator final drive and travel motor system. It outlines 16 steps to disassemble the final drive which include draining fluids, removing fittings and valves, and using tools to pull bearings. It also details 14 steps to disassemble the travel motor which involve removing seals, pistons, plates and springs. Safety cautions are provided throughout regarding releasing pressures and spring forces.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
2. Shutdown SIS
Previous Screen
Product: COMPACT TRACK LOADER
Model: 299D2 COMPACT TRACK LOADER BY4
Configuration: 299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWERED BY C3.8 Engine
Disassembly and Assembly
C3.8 Engines for Caterpillar Built Machines
Media Number -UENR0129-08 Publication Date -01/09/2015 Date Updated -19/05/2016
i04664023
Flywheel - Install
SMCS - 1156-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-7994 Guide Bolt 2
Always wear protective gloves when handling parts that have been
heated.
1/4
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g02797127
Typical example
1. If the ring gear was removed, follow Steps 1.a through 1.c to install ring gear (7) to flywheel
(8).
a. Identify the orientation of the new ring gear in order to install the ring gear correctly
onto the flywheel.
Note: The chamfered side of gear teeth (Y) must face toward the starting motor when
the flywheel is installed. This will ensure the correct engagement of the starting
motor.
b. Heat ring gear (3) in an oven to a maximum temperature of 150°C (302°F) prior to
installation.
Note: Do not use a torch to heat the ring gear.
c. Ensure that the orientation of ring gear (7) is correct and quickly install the ring gear
onto flywheel (8).
Illustration 2 g02797120
2/4
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 2. Thoroughly clean the flywheel housing. Inspect the crankshaft rear seal for leaks. If there
are any oil leaks replace the crankshaft rear seal. Refer to Disassembly and Assembly,
"Crankshaft Rear Seal - Remove and Install".
3. Install Tooling (A) on the crankshaft.
4. Use a suitable lifting device to position flywheel assembly (5). The weight of flywheel
assembly (5) is approximately 23 kg (50 lb).
5. Align flywheel assembly (5) with Tooling (A). Install flywheel assembly (5) to the
crankshaft.
Note: Ensure the correct orientation of the flywheel on the crankshaft.
6. Apply clean engine oil onto bolts (6). Install bolts (6) finger tight.
7. Remove Tooling (A) and install the two remaining bolts (6).
8. Remove the lifting device from the flywheel.
9. Use a suitable tool to prevent flywheel assembly (5) from rotating. Tighten bolts (6) to a
torque of 98.1 to 107 N·m (72 to 79 lb ft).
10. Check the concentricity of the flywheel. Refer to Systems Operation, Testing and Adjusting,
"Flywheel - Inspect".
Illustration 3 g02797118
11. Install pump coupling (4). Install bolts (3).
3/4
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 4 g02797115
12. Install cover (2). Install bolts (1).
End By:
a. Install the starting motor.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 30 23:51:46 UTC+0800 2019
4/4
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: COMPACT TRACK LOADER
Model: 299D2 COMPACT TRACK LOADER BY4
Configuration: 299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWERED BY C3.8 Engine
Disassembly and Assembly
C3.8 Engines for Caterpillar Built Machines
Media Number -UENR0129-08 Publication Date -01/09/2015 Date Updated -19/05/2016
i04664019
Crankshaft Rear Seal - Remove and Install
SMCS - 1161-010
Removal Procedure
Start By:
a. Remove the flywheel.
Illustration 1 g02797554
1. Drill three holes in lip seal (1). Use a suitable slide hammer to remove lip seal (1).
2. Remove ring seal (2).
Installation Procedure
Table 1
Required Tools
1/2
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Tool Part Number Part Description Qty
A 393-2571 Driver 1
Illustration 2 g02797554
Illustration 3 g02870418
1. Use Tooling (A) to install ring seal (2).
2. Use Tooling (A) to install lip seal (1).
End By:
a. Install the flywheel.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 30 23:52:42 UTC+0800 2019
2/2
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Shutdown SIS
Previous Screen
Product: COMPACT TRACK LOADER
Model: 299D2 COMPACT TRACK LOADER BY4
Configuration: 299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWERED BY C3.8 Engine
Disassembly and Assembly
C3.8 Engines for Caterpillar Built Machines
Media Number -UENR0129-08 Publication Date -01/09/2015 Date Updated -19/05/2016
i04839813
Crankshaft Rear Seal Carrier - Remove and Install
SMCS - 1161-010-C3
Removal Procedure
1. Refer to Specifications, "Crankshaft".
Illustration 1 g02869998
2. Remove bolts (1). Use two of bolts (1) to remove bearing case cover (2) .
1/3
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 2 g02870025
3. Remove lip seal (3) from bearing case cover (2) .
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 393-2571 Seal Installer 1
B - Three Bond 1217H -
Illustration 3 g02870025
2/3
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 4 g02870418
1. Use Tooling (A) to install lip seal (3) into bearing case cover (2) .
Illustration 5 g02869998
2. Apply Tooling (B) onto the mating surface of bearing case cover (2). Apply clean engine oil
onto the lip seal. Install bearing case cover (2) .
3. Install bolts (1). Tighten bolts (1) to a torque of 25.5 ± 1.5 N·m (18.8 ± 1.1 lb ft).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 30 23:53:38 UTC+0800 2019
3/3
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: COMPACT TRACK LOADER
Model: 299D2 COMPACT TRACK LOADER BY4
Configuration: 299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWERED BY C3.8 Engine
Disassembly and Assembly
C3.8 Engines for Caterpillar Built Machines
Media Number -UENR0129-08 Publication Date -01/09/2015 Date Updated -19/05/2016
i06272842
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 439-3938 Link Bracket 2
B - Three Bond1217H 1
Start By:
a. Remove the bearing case cover.
Illustration 1 g02797548
1/2
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. 1. Attach Tooling (A) and a suitable lifting device onto flywheel housing (1). The weight of
flywheel housing (1) is approximately 45 kg (100 lb).
2. Remove bolts (2) and bolts (3). Remove flywheel housing (1).
Installation Procedure
1. Install flywheel housing (1) in the reverse order of removal.
a. Apply Tooling (B) onto the mating surface of flywheel housing (1).
b. For the SSL, MTL, and CTL models that end in D2 models (BL2, MD2, BL7, HP2,
FD2, DX2, DX9, and BY4), tighten bolts (3) and bolts (2) to a torque of
103 ± 14 N·m (76 ± 10 lb ft).
c. For all other models, tighten bolts (3) and bolts (2) to a torque of 78 ± 12 N·m
(56 ± 9 lb ft).
d. Refer to Systems Operation, Testing and Adjusting, "Flywheel Housing - Inspect".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 30 23:54:34 UTC+0800 2019
2/2
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: COMPACT TRACK LOADER
Model: 299D2 COMPACT TRACK LOADER BY4
Configuration: 299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWERED BY C3.8 Engine
Disassembly and Assembly
C3.8 Engines for Caterpillar Built Machines
Media Number -UENR0129-08 Publication Date -01/09/2015 Date Updated -19/05/2016
i04664013
Crankshaft Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 393-2572 Flywheel Stopper 1
Start By:
a. Remove the belt.
1. Install Tooling (A) onto the flywheel.
Illustration 1 g02860756
2. Remove bolt (1) to remove pulley (2).
1/2
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Installation Procedure
1. Install pulley (2) in the reverse order of removal.
a. Apply clean engine oil onto bolt (1).
b. Tighten bolt (1) to a torque of 264.5 ± 9.5 N·m (195.1 ± 7.0 lb ft).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 30 23:55:29 UTC+0800 2019
2/2
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: COMPACT TRACK LOADER
Model: 299D2 COMPACT TRACK LOADER BY4
Configuration: 299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWERED BY C3.8 Engine
Disassembly and Assembly
C3.8 Engines for Caterpillar Built Machines
Media Number -UENR0129-08 Publication Date -01/09/2015 Date Updated -19/05/2016
i04664010
Crankshaft Front Seal - Remove and Install
SMCS - 1160-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-8145 Drill Bit (4.10 mm) 1
B 1U-7600 Slide Hammer Puller 1
Start By:
a. Remove the crankshaft pulley.
NOTICE
Ensure that the main lip is used in order to remove the crankshaft
front seal. Do not damage the edge of the housing for the crankshaft
front seal.
1/3
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 1 g02860787
1. Use Tooling (A) to drill three evenly spaced holes in crankshaft front seal (1).
2. Use Tooling (B) to carefully remove crankshaft front seal (1). Alternate the position of
Tooling (B) from one hole to another hole to allow the crankshaft front seal to be removed.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
C 393-2570 Seal Installer 1
Illustration 2 g02860787
2/3
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 3 g02866181
1. Lubricate the outside diameter of a new crankshaft front seal (1) with clean engine oil. Use
Tooling (C) to install crankshaft front seal (1).
2. Apply clean engine oil to the lip of crankshaft front seal (1).
End By:
a. Install the crankshaft pulley.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 30 23:56:25 UTC+0800 2019
3/3
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
19. Shutdown SIS
Previous Screen
Product: COMPACT TRACK LOADER
Model: 299D2 COMPACT TRACK LOADER BY4
Configuration: 299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWERED BY C3.8 Engine
Disassembly and Assembly
C3.8 Engines for Caterpillar Built Machines
Media Number -UENR0129-08 Publication Date -01/09/2015 Date Updated -19/05/2016
i04801361
Idler Gear - Remove and Install
SMCS - 1206
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 393-2572 Flywheel Stopper 1
B 393-2573 Driver 1
Start By:
a. Remove the front housing.
1. Ensure that number four piston is at the top center position on the compression stroke. Refer
to Systems Operation, Testing and Adjusting, "Finding Top Center Position for No. 4
Piston".
1/3
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 1 g02871716
2. Ensure that timing marks on the gears are aligned.
Alternatively, make temporary timing marks on the gears in order to show alignment.
3. Install Tooling (A) onto the flywheel. Remove bolts (1) and plate (2).
Illustration 2 g02872045
4. Remove idler gear (3), shaft (4), and plate (5).
2/3
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 3 g02920337
5. Use Tooling (B) to remove bushing (6) from idler gear (3).
Installation Procedure
1. Install idler gear (3) in the reverse order of removal.
a. Apply clean engine oil onto the bore of idler gear (3) and bushing (6).
b. Ensure that edge of bushing (6) is flush with the edge of the bore that is in idler gear
(3).
c. Tighten bolts (1) to a torque of 25.5 ± 1.5 N·m (18.8 ± 1.1 lb ft).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 30 23:57:21 UTC+0800 2019
3/3
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: COMPACT TRACK LOADER
Model: 299D2 COMPACT TRACK LOADER BY4
Configuration: 299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWERED BY C3.8 Engine
Disassembly and Assembly
C3.8 Engines for Caterpillar Built Machines
Media Number -UENR0129-08 Publication Date -01/09/2015 Date Updated -19/05/2016
i06662240
Idler Gear - Remove and Install
SMCS - 1206
S/N - BL21-UP
S/N - BL71-UP
S/N - BY41-UP
S/N - DX21-UP
S/N - DX91-UP
S/N - FD21-UP
S/N - HP21-UP
S/N - MD21-UP
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 393-2572 Flywheel Stopper 1
Start By:
a. Remove the front housing.
1. Ensure that number four piston is at the top center position on the compression stroke. Refer
to Systems Operation, Testing and Adjusting, "Finding Top Center Position for No. 4
Piston".
1/2
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 1 g06066040
2. Ensure that timing marks on the gears are aligned.
Alternatively, make temporary timing marks on the gears to show alignment.
3. Install Tooling (A) onto the flywheel. Remove bolts (2) and idler gear (3).
4. Remove nuts (1) and idler gear (4).
Installation Procedure
1. Install the idler gears in the reverse order of removal.
a. Tighten nuts (1) to a torque of 24 N·m to 27 N·m (212 lb in to 239 lb in).
b. Tighten bolts (2) to a torque of 24 N·m to 27 N·m (212 lb in to 239 lb in).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 30 23:58:16 UTC+0800 2019
2/2
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...