The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 compact track loader. It describes how to install the flywheel, including cleaning and heating the ring gear. It also details removing and installing the crankshaft rear seal, crankshaft rear seal carrier, flywheel housing, crankshaft pulley, and crankshaft front seal. Tools required are listed for each procedure.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 compact track loader, including:
- Removing and installing the flywheel, which involves cleaning surfaces, heating the ring gear, and torquing bolts to a specified value.
- Removing and installing the crankshaft rear seal, which involves drilling holes, using a slide hammer, and pressing in new seals.
- Removing and installing the crankshaft rear seal carrier, bearing case cover, and lip seal using seal installation tools and threadlocker.
- Removing and installing the flywheel housing, which requires lifting equipment and torquing bolts to a specified value.
-
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 compact track loader, including:
- Removing and installing the flywheel, which involves cleaning surfaces, heating the ring gear, and torquing bolts to a specified value.
- Removing and installing the crankshaft rear seal, which involves drilling holes, using a slide hammer, and pressing in new seals.
- Removing and installing the crankshaft rear seal carrier, bearing case cover, and lip seal using seal installation tools and threadlocker.
- Removing and installing the flywheel housing, which requires lifting equipment and torquing bolts to a specified value.
-
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 Compact Track Loader, including:
- Flywheel installation which requires cleaning surfaces, heating the ring gear, and torquing bolts to a specified value.
- Crankshaft rear seal replacement involving removing the old seal and pressing in a new one using specific tools.
- Removing and installing the flywheel housing which requires attaching lifting brackets and torquing bolts to a specified value.
- Procedures for the crankshaft pulley, front seal, and bearing case cover that include cleaning, applying oil, and ensuring proper torque on fasteners.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 Compact Track Loader, including:
- Flywheel installation which requires cleaning surfaces, heating the ring gear, and torquing bolts to a specified value.
- Crankshaft rear seal replacement involving removing the old seal and pressing in a new one using specific tools.
- Removing and installing the flywheel housing which requires attaching lifting equipment and torquing bolts to a specified value.
- Procedures for the crankshaft pulley, front seal, and bearing case cover that include cleaning, applying oil, and ensuring proper orientation of parts.
The document provides instructions to remove and install the valve mechanism cover on a Caterpillar C3.8 engine. The removal procedure involves disconnecting wire harnesses, tubes, and bolts. The cover and gasket are then removed. Installation is the reverse of removal, requiring reinstallation of the cover, gasket, bolts, wires, and tubes. Bolts and nuts are tightened to specified torque values.
The document provides instructions to remove and install the valve mechanism cover on a Caterpillar C3.8 engine. The removal procedure involves disconnecting wire harnesses, tubes, and bolts. The cover and gasket are then removed. Installation is the reverse of removal, requiring reinstallation of the cover and gaskets and tightening of bolts and nuts to the specified torques.
The document provides instructions to remove and install the valve mechanism cover on a Caterpillar C3.8 engine. The removal procedure involves disconnecting wire harnesses, tubes, and bolts. The cover and gasket are then removed. Installation is the reverse of removal, requiring reinstallation of the cover, gasket, bolts, wires and tubes. Bolts and nuts are tightened to specified torque values.
The document provides instructions for removing and installing an idler gear on a Caterpillar 299D2 XHP compact track loader. The removal procedure involves removing the front housing, ensuring the piston is at top center position, marking gear alignment, installing a flywheel stopper tool, and removing bolts, plates and the idler gear. The installation procedure specifies cleaning and applying oil to parts, ensuring correct bushing alignment, and tightening bolts to the specified torque.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 compact track loader, including:
- Removing and installing the flywheel, which involves cleaning surfaces, heating the ring gear, and torquing bolts to a specified value.
- Removing and installing the crankshaft rear seal, which involves drilling holes, using a slide hammer, and pressing in new seals.
- Removing and installing the crankshaft rear seal carrier, bearing case cover, and lip seal using seal installation tools and threadlocker.
- Removing and installing the flywheel housing, which requires lifting equipment and torquing bolts to a specified value.
-
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 compact track loader, including:
- Removing and installing the flywheel, which involves cleaning surfaces, heating the ring gear, and torquing bolts to a specified value.
- Removing and installing the crankshaft rear seal, which involves drilling holes, using a slide hammer, and pressing in new seals.
- Removing and installing the crankshaft rear seal carrier, bearing case cover, and lip seal using seal installation tools and threadlocker.
- Removing and installing the flywheel housing, which requires lifting equipment and torquing bolts to a specified value.
-
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 Compact Track Loader, including:
- Flywheel installation which requires cleaning surfaces, heating the ring gear, and torquing bolts to a specified value.
- Crankshaft rear seal replacement involving removing the old seal and pressing in a new one using specific tools.
- Removing and installing the flywheel housing which requires attaching lifting brackets and torquing bolts to a specified value.
- Procedures for the crankshaft pulley, front seal, and bearing case cover that include cleaning, applying oil, and ensuring proper torque on fasteners.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 Compact Track Loader, including:
- Flywheel installation which requires cleaning surfaces, heating the ring gear, and torquing bolts to a specified value.
- Crankshaft rear seal replacement involving removing the old seal and pressing in a new one using specific tools.
- Removing and installing the flywheel housing which requires attaching lifting equipment and torquing bolts to a specified value.
- Procedures for the crankshaft pulley, front seal, and bearing case cover that include cleaning, applying oil, and ensuring proper orientation of parts.
The document provides instructions to remove and install the valve mechanism cover on a Caterpillar C3.8 engine. The removal procedure involves disconnecting wire harnesses, tubes, and bolts. The cover and gasket are then removed. Installation is the reverse of removal, requiring reinstallation of the cover, gasket, bolts, wires, and tubes. Bolts and nuts are tightened to specified torque values.
The document provides instructions to remove and install the valve mechanism cover on a Caterpillar C3.8 engine. The removal procedure involves disconnecting wire harnesses, tubes, and bolts. The cover and gasket are then removed. Installation is the reverse of removal, requiring reinstallation of the cover and gaskets and tightening of bolts and nuts to the specified torques.
The document provides instructions to remove and install the valve mechanism cover on a Caterpillar C3.8 engine. The removal procedure involves disconnecting wire harnesses, tubes, and bolts. The cover and gasket are then removed. Installation is the reverse of removal, requiring reinstallation of the cover, gasket, bolts, wires and tubes. Bolts and nuts are tightened to specified torque values.
The document provides instructions for removing and installing an idler gear on a Caterpillar 299D2 XHP compact track loader. The removal procedure involves removing the front housing, ensuring the piston is at top center position, marking gear alignment, installing a flywheel stopper tool, and removing bolts, plates and the idler gear. The installation procedure specifies cleaning and applying oil to parts, ensuring correct bushing alignment, and tightening bolts to the specified torque.
The document provides instructions for removing and installing an idler gear on a Caterpillar 299D2 XHP compact track loader. The removal procedure involves removing the front housing, ensuring the piston is at top center position, marking timing gear alignment, installing a flywheel stopper tool, and removing bolts and plates. The installation procedure specifies cleaning and applying oil to parts, ensuring correct bushing alignment, and torquing bolts to the specified values.
The document provides instructions for removing and installing an idler gear on a Caterpillar 299D2 XHP compact track loader. The removal procedure involves removing the front housing, ensuring the piston is at top center position, marking timing gear alignment, installing a flywheel stopper tool, and removing bolts and plates. The installation procedure specifies cleaning and applying oil to parts, ensuring correct bushing alignment, and torquing bolts to the specified values.
The document provides instructions for removing and installing an idler gear on a Caterpillar 299D2 XHP compact track loader. The removal procedure involves removing the front housing, ensuring the piston is at top center position, marking gear alignment, installing a flywheel stopper tool, and removing bolts, plates and the idler gear. The installation procedure specifies cleaning and applying oil to parts, ensuring correct bushing alignment, and tightening bolts to the specified torque.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 XHP compact track loader. The procedures include removing the idler gear by first ensuring the engine is at top center position and removing bolts. Other removal procedures include the front housing, fumes disposal filter, valve mechanism cover and related components. Reinstallation is done in reverse order, applying oil and torquing bolts to the specified values.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 XHP compact track loader. The procedures include removing the idler gear by first ensuring the engine is at top center position and removing bolts. Other removal procedures include the front housing, fumes disposal filter, and valve mechanism cover. Reinstallation is done by reversing the removal steps and tightening bolts to the specified torques.
The document provides instructions to remove and install a valve mechanism cover on a Caterpillar C3.8 engine. It describes:
1. Disconnecting various tubes, harnesses, and hoses attached to the cover.
2. Removing bolts to take off the cover and gasket.
3. Cleaning and inspecting the mating surfaces before installing the new cover in reverse order using specified torques for the bolts.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 XHP compact track loader. The procedures include removing the idler gear by first ensuring the engine is at top center position and removing bolts, nuts and plates. The front housing is removed by disconnecting wiring harnesses and belts, removing bolts, and using a flywheel stopper tool. The fumes disposal filter is removed by disconnecting hoses and removing a bolt and bracket.
The document provides instructions to remove and install a valve mechanism cover on a Caterpillar C3.8 engine. It describes:
1. Disconnecting various tubes, harnesses, and hoses attached to the cover.
2. Removing bolts to take off the cover and gasket.
3. Cleaning and inspecting the mating surfaces before installing the new cover in reverse order using specified torques for the bolts.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 XHP compact track loader. The procedures include removing the idler gear by first ensuring the engine is at top center position and removing bolts, nuts and plates. The front housing is removed by disconnecting wiring harnesses and belts, removing bolts, and using a flywheel stopper tool. The fumes disposal filter is removed by disconnecting hoses and removing a bolt and bracket.
The document provides instructions to remove and install a valve mechanism cover on a Caterpillar C3.8 engine. It describes:
1. Disconnecting various tubes, harnesses, and hoses attached to the cover.
2. Removing bolts to take off the cover and gasket.
3. Cleaning and inspecting the mating surfaces before installing the new cover in reverse order using specified torques for the bolts.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 XHP compact track loader. The procedures include removing the idler gear by first ensuring the engine is at top center position and removing bolts. Other removal procedures include the front housing, fumes disposal filter, valve mechanism cover and related components. Reinstallation is done by reversing the removal steps and tightening bolts to the specified torques.
The document provides instructions for removing and installing an idler gear on a Caterpillar 299D2 XHP compact track loader. The removal procedure involves removing the front housing, ensuring the piston and gear timing marks are aligned, installing a flywheel stopper tool, and removing bolts and plates. The installation procedure specifies reversing the removal steps and tightening bolts to the specified torque values.
The document provides instructions for removing and installing an idler gear on a Caterpillar 299D2 XHP compact track loader. The removal procedure involves removing the front housing, ensuring the piston and gear timing marks are aligned, installing a flywheel stopper tool, and removing bolts and plates. The installation procedure specifies cleaning and lubricating parts, ensuring the bushing is flush, and tightening bolts to the specified torque.
The document provides instructions for removing and installing an idler gear on a Caterpillar 299D2 XHP compact track loader. The removal procedure involves removing the front housing, ensuring the piston and gear timing marks are aligned, installing a flywheel stopper tool, and removing bolts and plates. The installation procedure specifies cleaning and lubricating parts, ensuring components are flush, and tightening bolts to the specified torque using a flywheel stopper tool.
The document provides instructions for removing and installing an idler gear on a Caterpillar 299D2 XHP compact track loader. The removal procedure involves removing the front housing, ensuring the piston and gear timing marks are aligned, installing a flywheel stopper tool, and removing bolts and plates. The installation procedure specifies installing the idler gear in reverse order and tightening the bolts to the specified torque.
This document provides instructions for removing and installing various fuel system components on a 320C excavator with a 3066 engine. It describes removing the fuel filter base, fuel injection lines, fuel injection nozzles, fuel shutoff solenoid, and fuel injection pump. Detailed steps and illustrations are provided for each procedure, including required tools and safety precautions.
This document provides instructions for removing and installing the engine oil pump and water pump on a Caterpillar 320C excavator. The oil pump removal instructions involve removing bolts, gears, seals and other components. The installation involves cleaning parts, pressing components, heating items, and torquing bolts to the specified values. The water pump instructions similarly provide a process to remove the pump, pulley, seals and disassemble internal parts. Reassembly involves installing bearings, seals and torquing bolts. Precautions are given to contain fluids and ensure clean parts.
This document provides instructions for removing and installing track carrier rollers, track rollers, and separating the track on a 320C Excavator. It describes:
1) Releasing tension on the track and loosening a relief valve before removing components.
2) Using tools like a hydraulic jack and lifting forks to support the track assembly and remove rollers and bolts.
3) Cleaning surfaces, positioning components, and reinstalling bolts and rollers in the reverse order of removal.
Caterpillar Cat 320C and 320C L Excavator (Prefix MAB) Service Repair Manual ...tengtui535
This document provides instructions for disassembling a recoil spring assembly. It begins by removing the front idler and recoil spring assembly from the machine. A specialized recoil spring bench tool is then used to disassemble the recoil spring. The spring is under high tension and special precautions are required when handling it. The tool supports the spring and allows removing the retaining nut safely to separate the spring from other components.
Caterpillar Cat 320C and 320C L Excavator (Prefix ANB) Service Repair Manual ...tengtui535
The document provides instructions for removing and installing various components on a 320C excavator, including:
1. Actuator motors that control air dampers and airflow for temperature control, fresh air intake, rear window defroster, and more. The procedure involves disconnecting wiring harnesses, removing mounting screws, and removing the component.
2. A fan speed control unit for the blower. The procedure disconnects the wiring harness and removes two mounting screws to release the component.
3. An ambient air temperature sensor mounted on the excavator frame. The procedure disconnects the wiring harness, cuts a cable strap, and removes the sensor.
4. A coolant temperature sensor. The procedure
Caterpillar Cat 320C and 320C L Excavator (Prefix AMC) Service Repair Manual ...tengtui535
The document provides removal and installation instructions for various components of the climate control system in a Caterpillar 320C excavator, including actuator motors, a fan speed control, and a temperature sensor. The procedures describe disconnecting electrical connections and linkages, removing mounting hardware, and reversing the steps for installation. Components include actuator motors for air dampers controlling temperature, front and rear air flow, fresh/recirculated air, and front and rear windows.
This document provides instructions for assembling and disassembling parts of a 320 GC Excavator model BR4, including the travel motor and final drive. It lists the required tools and parts and includes illustrations of the assembly and disassembly procedures. The travel motor assembly instructions involve positioning the excavator, installing nuts and bolts, and attaching lifting eyes and plugs. The final drive disassembly instructions specify removing the final drive and separating the sprocket after removing the travel motor.
More Related Content
Similar to Caterpillar Cat 299D2 COMPACT TRACK LOADER (Prefix BY4) Service Repair Manual Instant Download.pdf
The document provides instructions for removing and installing an idler gear on a Caterpillar 299D2 XHP compact track loader. The removal procedure involves removing the front housing, ensuring the piston is at top center position, marking timing gear alignment, installing a flywheel stopper tool, and removing bolts and plates. The installation procedure specifies cleaning and applying oil to parts, ensuring correct bushing alignment, and torquing bolts to the specified values.
The document provides instructions for removing and installing an idler gear on a Caterpillar 299D2 XHP compact track loader. The removal procedure involves removing the front housing, ensuring the piston is at top center position, marking timing gear alignment, installing a flywheel stopper tool, and removing bolts and plates. The installation procedure specifies cleaning and applying oil to parts, ensuring correct bushing alignment, and torquing bolts to the specified values.
The document provides instructions for removing and installing an idler gear on a Caterpillar 299D2 XHP compact track loader. The removal procedure involves removing the front housing, ensuring the piston is at top center position, marking gear alignment, installing a flywheel stopper tool, and removing bolts, plates and the idler gear. The installation procedure specifies cleaning and applying oil to parts, ensuring correct bushing alignment, and tightening bolts to the specified torque.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 XHP compact track loader. The procedures include removing the idler gear by first ensuring the engine is at top center position and removing bolts. Other removal procedures include the front housing, fumes disposal filter, valve mechanism cover and related components. Reinstallation is done in reverse order, applying oil and torquing bolts to the specified values.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 XHP compact track loader. The procedures include removing the idler gear by first ensuring the engine is at top center position and removing bolts. Other removal procedures include the front housing, fumes disposal filter, and valve mechanism cover. Reinstallation is done by reversing the removal steps and tightening bolts to the specified torques.
The document provides instructions to remove and install a valve mechanism cover on a Caterpillar C3.8 engine. It describes:
1. Disconnecting various tubes, harnesses, and hoses attached to the cover.
2. Removing bolts to take off the cover and gasket.
3. Cleaning and inspecting the mating surfaces before installing the new cover in reverse order using specified torques for the bolts.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 XHP compact track loader. The procedures include removing the idler gear by first ensuring the engine is at top center position and removing bolts, nuts and plates. The front housing is removed by disconnecting wiring harnesses and belts, removing bolts, and using a flywheel stopper tool. The fumes disposal filter is removed by disconnecting hoses and removing a bolt and bracket.
The document provides instructions to remove and install a valve mechanism cover on a Caterpillar C3.8 engine. It describes:
1. Disconnecting various tubes, harnesses, and hoses attached to the cover.
2. Removing bolts to take off the cover and gasket.
3. Cleaning and inspecting the mating surfaces before installing the new cover in reverse order using specified torques for the bolts.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 XHP compact track loader. The procedures include removing the idler gear by first ensuring the engine is at top center position and removing bolts, nuts and plates. The front housing is removed by disconnecting wiring harnesses and belts, removing bolts, and using a flywheel stopper tool. The fumes disposal filter is removed by disconnecting hoses and removing a bolt and bracket.
The document provides instructions to remove and install a valve mechanism cover on a Caterpillar C3.8 engine. It describes:
1. Disconnecting various tubes, harnesses, and hoses attached to the cover.
2. Removing bolts to take off the cover and gasket.
3. Cleaning and inspecting the mating surfaces before installing the new cover in reverse order using specified torques for the bolts.
The document provides instructions for removing and installing various engine components on a Caterpillar 299D2 XHP compact track loader. The procedures include removing the idler gear by first ensuring the engine is at top center position and removing bolts. Other removal procedures include the front housing, fumes disposal filter, valve mechanism cover and related components. Reinstallation is done by reversing the removal steps and tightening bolts to the specified torques.
The document provides instructions for removing and installing an idler gear on a Caterpillar 299D2 XHP compact track loader. The removal procedure involves removing the front housing, ensuring the piston and gear timing marks are aligned, installing a flywheel stopper tool, and removing bolts and plates. The installation procedure specifies reversing the removal steps and tightening bolts to the specified torque values.
The document provides instructions for removing and installing an idler gear on a Caterpillar 299D2 XHP compact track loader. The removal procedure involves removing the front housing, ensuring the piston and gear timing marks are aligned, installing a flywheel stopper tool, and removing bolts and plates. The installation procedure specifies cleaning and lubricating parts, ensuring the bushing is flush, and tightening bolts to the specified torque.
The document provides instructions for removing and installing an idler gear on a Caterpillar 299D2 XHP compact track loader. The removal procedure involves removing the front housing, ensuring the piston and gear timing marks are aligned, installing a flywheel stopper tool, and removing bolts and plates. The installation procedure specifies cleaning and lubricating parts, ensuring components are flush, and tightening bolts to the specified torque using a flywheel stopper tool.
The document provides instructions for removing and installing an idler gear on a Caterpillar 299D2 XHP compact track loader. The removal procedure involves removing the front housing, ensuring the piston and gear timing marks are aligned, installing a flywheel stopper tool, and removing bolts and plates. The installation procedure specifies installing the idler gear in reverse order and tightening the bolts to the specified torque.
Similar to Caterpillar Cat 299D2 COMPACT TRACK LOADER (Prefix BY4) Service Repair Manual Instant Download.pdf (15)
This document provides instructions for removing and installing various fuel system components on a 320C excavator with a 3066 engine. It describes removing the fuel filter base, fuel injection lines, fuel injection nozzles, fuel shutoff solenoid, and fuel injection pump. Detailed steps and illustrations are provided for each procedure, including required tools and safety precautions.
This document provides instructions for removing and installing the engine oil pump and water pump on a Caterpillar 320C excavator. The oil pump removal instructions involve removing bolts, gears, seals and other components. The installation involves cleaning parts, pressing components, heating items, and torquing bolts to the specified values. The water pump instructions similarly provide a process to remove the pump, pulley, seals and disassemble internal parts. Reassembly involves installing bearings, seals and torquing bolts. Precautions are given to contain fluids and ensure clean parts.
This document provides instructions for removing and installing track carrier rollers, track rollers, and separating the track on a 320C Excavator. It describes:
1) Releasing tension on the track and loosening a relief valve before removing components.
2) Using tools like a hydraulic jack and lifting forks to support the track assembly and remove rollers and bolts.
3) Cleaning surfaces, positioning components, and reinstalling bolts and rollers in the reverse order of removal.
Caterpillar Cat 320C and 320C L Excavator (Prefix MAB) Service Repair Manual ...tengtui535
This document provides instructions for disassembling a recoil spring assembly. It begins by removing the front idler and recoil spring assembly from the machine. A specialized recoil spring bench tool is then used to disassemble the recoil spring. The spring is under high tension and special precautions are required when handling it. The tool supports the spring and allows removing the retaining nut safely to separate the spring from other components.
Caterpillar Cat 320C and 320C L Excavator (Prefix ANB) Service Repair Manual ...tengtui535
The document provides instructions for removing and installing various components on a 320C excavator, including:
1. Actuator motors that control air dampers and airflow for temperature control, fresh air intake, rear window defroster, and more. The procedure involves disconnecting wiring harnesses, removing mounting screws, and removing the component.
2. A fan speed control unit for the blower. The procedure disconnects the wiring harness and removes two mounting screws to release the component.
3. An ambient air temperature sensor mounted on the excavator frame. The procedure disconnects the wiring harness, cuts a cable strap, and removes the sensor.
4. A coolant temperature sensor. The procedure
Caterpillar Cat 320C and 320C L Excavator (Prefix AMC) Service Repair Manual ...tengtui535
The document provides removal and installation instructions for various components of the climate control system in a Caterpillar 320C excavator, including actuator motors, a fan speed control, and a temperature sensor. The procedures describe disconnecting electrical connections and linkages, removing mounting hardware, and reversing the steps for installation. Components include actuator motors for air dampers controlling temperature, front and rear air flow, fresh/recirculated air, and front and rear windows.
This document provides instructions for assembling and disassembling parts of a 320 GC Excavator model BR4, including the travel motor and final drive. It lists the required tools and parts and includes illustrations of the assembly and disassembly procedures. The travel motor assembly instructions involve positioning the excavator, installing nuts and bolts, and attaching lifting eyes and plugs. The final drive disassembly instructions specify removing the final drive and separating the sprocket after removing the travel motor.
Caterpillar Cat 319D L Excavator (Prefix KRM) Service Repair Manual Instant D...tengtui535
This document provides instructions for disassembling and assembling the final drive of a 319D L excavator. The disassembly process involves removing over 30 individual parts from the final drive assembly including covers, gears, carriers, seals, and housings. The assembly process reverses the disassembly steps and provides details on installing new seals and determining the correct shim thickness. Proper cleaning, lubrication, and torque specifications are emphasized throughout.
Caterpillar Cat 319D L and 319D LN Excavator (Prefix ZGZ) Service Repair Manu...tengtui535
The document provides instructions for disassembling and assembling the final drive of a 319D L excavator. It lists the required tools and outlines 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and housing. It then outlines 28 steps for reassembling the final drive, including pressing in bearings, installing seals, and determining the correct shim thickness. The overall procedure involves separating, cleaning, and reassembling over 15 individual parts and components of the final drive.
Caterpillar Cat 319D L and 319D LN Excavator (Prefix ZCA) Service Repair Manu...tengtui535
This document provides assembly instructions for a final drive on an excavator model 319D L. It involves 38 steps including installing bearings, seals, gears, and other components into housings and covers. Precise measurements and torque specifications are required. Cleanliness is important to prevent contamination. The assembly is completed by installing the final drive assembly into the excavator frame using lifting equipment due to the 310 kg weight.
Caterpillar Cat 319D L and 319D LN Excavator (Prefix WBJ) Service Repair Manu...tengtui535
The document provides instructions for disassembling and assembling a final drive component of an excavator. It includes 33 steps for disassembly, removing components like the cover, carrier assembly, planetary gears, and seals. The assembly section has 13 steps, including pressing in bearings, installing seals and pins, and using shims to set proper bearing preload when installing the main housing onto the motor housing. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar Cat 319D L and 319D LN Excavator (Prefix RJP) Service Repair Manu...tengtui535
The document provides instructions for disassembling and assembling a final drive on a 319D L and 319D LN excavator. The disassembly procedure involves removing 33 individual parts from the final drive including the cover, carrier assembly, ring gears, and main housing. The assembly procedure instructs installing these 33 parts in reverse order and includes steps for preloading the bearings and determining the correct shim thickness.
Caterpillar Cat 319D L and 319D LN Excavator (Prefix KFM) Service Repair Manu...tengtui535
The document provides instructions for disassembling and assembling the final drive of a 319D L and 319D LN excavator. It lists 33 steps for disassembly, removing components like the cover, carrier assembly, ring gears, and seals. It then lists 31 steps for assembly, installing components in reverse order and noting that cleanliness is important, O-rings and seals should be replaced, and bearings should be preloaded to determine the correct shim thickness.
Caterpillar Cat 319D L and 319D LN Excavator (Prefix FMH) Service Repair Manu...tengtui535
The document provides instructions for disassembling and assembling a travel motor. It is a 27 step process to disassemble the motor which includes removing components like the head, brake piston, barrel assembly, cam plate and shaft assembly. The 27 step assembly process describes cleaning and lubricating parts, and installing components in reverse order of removal while ensuring proper alignment of markings and components. Special care must be taken to avoid damaging parts and ensure correct assembly of components like the cam plate and keys.
Caterpillar Cat 319D L and 319D LN Excavator (Prefix EAW) Service Repair Manu...tengtui535
The document provides instructions for disassembling and assembling a final drive component. It lists 33 steps for disassembly, removing parts like the cover, carrier assembly, planetary gears, and seals. The 21 steps for assembly install these parts in reverse order, including pressing in bearings, installing seals with special tools, and using shims to set proper bearing preload when joining the main housing to the motor housing. Proper cleaning and lubrication of parts is emphasized throughout.
Caterpillar Cat 319D L and 319D LN Excavator (Prefix AYF) Service Repair Manu...tengtui535
The document provides instructions for disassembling and assembling the final drive of a 319D L excavator. It lists 30 steps for disassembly, removing components like the cover, carrier assembly, ring gears, and seals. It then lists 33 steps for assembly, installing components in reverse order and noting that all parts must be cleaned, O-rings and seals replaced, and surfaces lubricated before assembly. Precise measurements and shim selection are required to set the bearing preload correctly.
This document provides instructions to disassemble and assemble the final drive of a 319D excavator. It describes in detail how to remove over 30 individual components of the final drive including the cover, carrier assembly, ring gears, and housing. Cleanliness is emphasized throughout. The assembly section matches the disassembly steps and includes precautions like replacing seals and applying anti-seize lubricant to bearings. Proper bearing preload is determined using measurements and shims.
Caterpillar Cat 318F L Excavator (Prefix HCP) Service Repair Manual Instant D...tengtui535
This document provides instructions for disassembling and assembling the travel motor of a 318F L Excavator. It lists the required tools and presents 31 steps for disassembly, including removing components like the springs, spools, caps, and head assembly. It then lists 29 steps for reassembly, instructing technicians to install components in the reverse order of removal. Safety warnings are provided throughout to remind technicians to wear protective equipment when working with pressurized air or spring-loaded parts.
Caterpillar Cat 318F L Excavator (Prefix FFT) Service Repair Manual Instant D...tengtui535
This document provides disassembly instructions for the final drive of a 318F L excavator. It describes 41 steps to fully disassemble the final drive components. Key steps include removing the sprocket, pistons, barrel assembly, planetary gears, sun gears, and housings. Safety warnings are provided to release pressures and springs carefully due to risk of injury from propelled parts.
Caterpillar Cat 318E L Excavator (Prefix WZS) Service Repair Manual Instant D...tengtui535
This document provides instructions for disassembling and assembling the final drive of a 318E L excavator. It describes in detail how to remove over 30 individual components of the final drive including gears, shafts, seals, housings and other parts. Precise steps are outlined for disassembly, and specifications and procedures are provided for reassembling each component in the proper order and with the correct tools, fasteners, seals and other materials. Torque specifications and application of sealants are noted throughout.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
2. Shutdown SIS
Previous Screen
Product: COMPACT TRACK LOADER
Model: 299D2 COMPACT TRACK LOADER BY4
Configuration: 299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWERED BY C3.8 Engine
Disassembly and Assembly
C3.8 Engines for Caterpillar Built Machines
Media Number -UENR0129-08 Publication Date -01/09/2015 Date Updated -19/05/2016
i04664023
Flywheel - Install
SMCS - 1156-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-7994 Guide Bolt 2
Always wear protective gloves when handling parts that have been
heated.
1/4
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g02797127
Typical example
1. If the ring gear was removed, follow Steps 1.a through 1.c to install ring gear (7) to flywheel
(8).
a. Identify the orientation of the new ring gear in order to install the ring gear correctly
onto the flywheel.
Note: The chamfered side of gear teeth (Y) must face toward the starting motor when
the flywheel is installed. This will ensure the correct engagement of the starting
motor.
b. Heat ring gear (3) in an oven to a maximum temperature of 150°C (302°F) prior to
installation.
Note: Do not use a torch to heat the ring gear.
c. Ensure that the orientation of ring gear (7) is correct and quickly install the ring gear
onto flywheel (8).
Illustration 2 g02797120
2/4
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 2. Thoroughly clean the flywheel housing. Inspect the crankshaft rear seal for leaks. If there
are any oil leaks replace the crankshaft rear seal. Refer to Disassembly and Assembly,
"Crankshaft Rear Seal - Remove and Install".
3. Install Tooling (A) on the crankshaft.
4. Use a suitable lifting device to position flywheel assembly (5). The weight of flywheel
assembly (5) is approximately 23 kg (50 lb).
5. Align flywheel assembly (5) with Tooling (A). Install flywheel assembly (5) to the
crankshaft.
Note: Ensure the correct orientation of the flywheel on the crankshaft.
6. Apply clean engine oil onto bolts (6). Install bolts (6) finger tight.
7. Remove Tooling (A) and install the two remaining bolts (6).
8. Remove the lifting device from the flywheel.
9. Use a suitable tool to prevent flywheel assembly (5) from rotating. Tighten bolts (6) to a
torque of 98.1 to 107 N·m (72 to 79 lb ft).
10. Check the concentricity of the flywheel. Refer to Systems Operation, Testing and Adjusting,
"Flywheel - Inspect".
Illustration 3 g02797118
11. Install pump coupling (4). Install bolts (3).
3/4
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 4 g02797115
12. Install cover (2). Install bolts (1).
End By:
a. Install the starting motor.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 30 23:51:46 UTC+0800 2019
4/4
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: COMPACT TRACK LOADER
Model: 299D2 COMPACT TRACK LOADER BY4
Configuration: 299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWERED BY C3.8 Engine
Disassembly and Assembly
C3.8 Engines for Caterpillar Built Machines
Media Number -UENR0129-08 Publication Date -01/09/2015 Date Updated -19/05/2016
i04664019
Crankshaft Rear Seal - Remove and Install
SMCS - 1161-010
Removal Procedure
Start By:
a. Remove the flywheel.
Illustration 1 g02797554
1. Drill three holes in lip seal (1). Use a suitable slide hammer to remove lip seal (1).
2. Remove ring seal (2).
Installation Procedure
Table 1
Required Tools
1/2
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Tool Part Number Part Description Qty
A 393-2571 Driver 1
Illustration 2 g02797554
Illustration 3 g02870418
1. Use Tooling (A) to install ring seal (2).
2. Use Tooling (A) to install lip seal (1).
End By:
a. Install the flywheel.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 30 23:52:42 UTC+0800 2019
2/2
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Shutdown SIS
Previous Screen
Product: COMPACT TRACK LOADER
Model: 299D2 COMPACT TRACK LOADER BY4
Configuration: 299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWERED BY C3.8 Engine
Disassembly and Assembly
C3.8 Engines for Caterpillar Built Machines
Media Number -UENR0129-08 Publication Date -01/09/2015 Date Updated -19/05/2016
i04839813
Crankshaft Rear Seal Carrier - Remove and Install
SMCS - 1161-010-C3
Removal Procedure
1. Refer to Specifications, "Crankshaft".
Illustration 1 g02869998
2. Remove bolts (1). Use two of bolts (1) to remove bearing case cover (2) .
1/3
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 2 g02870025
3. Remove lip seal (3) from bearing case cover (2) .
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 393-2571 Seal Installer 1
B - Three Bond 1217H -
Illustration 3 g02870025
2/3
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 4 g02870418
1. Use Tooling (A) to install lip seal (3) into bearing case cover (2) .
Illustration 5 g02869998
2. Apply Tooling (B) onto the mating surface of bearing case cover (2). Apply clean engine oil
onto the lip seal. Install bearing case cover (2) .
3. Install bolts (1). Tighten bolts (1) to a torque of 25.5 ± 1.5 N·m (18.8 ± 1.1 lb ft).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 30 23:53:38 UTC+0800 2019
3/3
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: COMPACT TRACK LOADER
Model: 299D2 COMPACT TRACK LOADER BY4
Configuration: 299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWERED BY C3.8 Engine
Disassembly and Assembly
C3.8 Engines for Caterpillar Built Machines
Media Number -UENR0129-08 Publication Date -01/09/2015 Date Updated -19/05/2016
i06272842
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 439-3938 Link Bracket 2
B - Three Bond1217H 1
Start By:
a. Remove the bearing case cover.
Illustration 1 g02797548
1/2
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. 1. Attach Tooling (A) and a suitable lifting device onto flywheel housing (1). The weight of
flywheel housing (1) is approximately 45 kg (100 lb).
2. Remove bolts (2) and bolts (3). Remove flywheel housing (1).
Installation Procedure
1. Install flywheel housing (1) in the reverse order of removal.
a. Apply Tooling (B) onto the mating surface of flywheel housing (1).
b. For the SSL, MTL, and CTL models that end in D2 models (BL2, MD2, BL7, HP2,
FD2, DX2, DX9, and BY4), tighten bolts (3) and bolts (2) to a torque of
103 ± 14 N·m (76 ± 10 lb ft).
c. For all other models, tighten bolts (3) and bolts (2) to a torque of 78 ± 12 N·m
(56 ± 9 lb ft).
d. Refer to Systems Operation, Testing and Adjusting, "Flywheel Housing - Inspect".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 30 23:54:34 UTC+0800 2019
2/2
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: COMPACT TRACK LOADER
Model: 299D2 COMPACT TRACK LOADER BY4
Configuration: 299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWERED BY C3.8 Engine
Disassembly and Assembly
C3.8 Engines for Caterpillar Built Machines
Media Number -UENR0129-08 Publication Date -01/09/2015 Date Updated -19/05/2016
i04664013
Crankshaft Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 393-2572 Flywheel Stopper 1
Start By:
a. Remove the belt.
1. Install Tooling (A) onto the flywheel.
Illustration 1 g02860756
2. Remove bolt (1) to remove pulley (2).
1/2
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Installation Procedure
1. Install pulley (2) in the reverse order of removal.
a. Apply clean engine oil onto bolt (1).
b. Tighten bolt (1) to a torque of 264.5 ± 9.5 N·m (195.1 ± 7.0 lb ft).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 30 23:55:29 UTC+0800 2019
2/2
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: COMPACT TRACK LOADER
Model: 299D2 COMPACT TRACK LOADER BY4
Configuration: 299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWERED BY C3.8 Engine
Disassembly and Assembly
C3.8 Engines for Caterpillar Built Machines
Media Number -UENR0129-08 Publication Date -01/09/2015 Date Updated -19/05/2016
i04664010
Crankshaft Front Seal - Remove and Install
SMCS - 1160-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-8145 Drill Bit (4.10 mm) 1
B 1U-7600 Slide Hammer Puller 1
Start By:
a. Remove the crankshaft pulley.
NOTICE
Ensure that the main lip is used in order to remove the crankshaft
front seal. Do not damage the edge of the housing for the crankshaft
front seal.
1/3
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 1 g02860787
1. Use Tooling (A) to drill three evenly spaced holes in crankshaft front seal (1).
2. Use Tooling (B) to carefully remove crankshaft front seal (1). Alternate the position of
Tooling (B) from one hole to another hole to allow the crankshaft front seal to be removed.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
C 393-2570 Seal Installer 1
Illustration 2 g02860787
2/3
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 3 g02866181
1. Lubricate the outside diameter of a new crankshaft front seal (1) with clean engine oil. Use
Tooling (C) to install crankshaft front seal (1).
2. Apply clean engine oil to the lip of crankshaft front seal (1).
End By:
a. Install the crankshaft pulley.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 30 23:56:25 UTC+0800 2019
3/3
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: COMPACT TRACK LOADER
Model: 299D2 COMPACT TRACK LOADER BY4
Configuration: 299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWERED BY C3.8 Engine
Disassembly and Assembly
C3.8 Engines for Caterpillar Built Machines
Media Number -UENR0129-08 Publication Date -01/09/2015 Date Updated -19/05/2016
i04801361
Idler Gear - Remove and Install
SMCS - 1206
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 393-2572 Flywheel Stopper 1
B 393-2573 Driver 1
Start By:
a. Remove the front housing.
1. Ensure that number four piston is at the top center position on the compression stroke. Refer
to Systems Operation, Testing and Adjusting, "Finding Top Center Position for No. 4
Piston".
1/3
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 1 g02871716
2. Ensure that timing marks on the gears are aligned.
Alternatively, make temporary timing marks on the gears in order to show alignment.
3. Install Tooling (A) onto the flywheel. Remove bolts (1) and plate (2).
Illustration 2 g02872045
4. Remove idler gear (3), shaft (4), and plate (5).
2/3
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 3 g02920337
5. Use Tooling (B) to remove bushing (6) from idler gear (3).
Installation Procedure
1. Install idler gear (3) in the reverse order of removal.
a. Apply clean engine oil onto the bore of idler gear (3) and bushing (6).
b. Ensure that edge of bushing (6) is flush with the edge of the bore that is in idler gear
(3).
c. Tighten bolts (1) to a torque of 25.5 ± 1.5 N·m (18.8 ± 1.1 lb ft).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 30 23:57:21 UTC+0800 2019
3/3
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: COMPACT TRACK LOADER
Model: 299D2 COMPACT TRACK LOADER BY4
Configuration: 299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWERED BY C3.8 Engine
Disassembly and Assembly
C3.8 Engines for Caterpillar Built Machines
Media Number -UENR0129-08 Publication Date -01/09/2015 Date Updated -19/05/2016
i06662240
Idler Gear - Remove and Install
SMCS - 1206
S/N - BL21-UP
S/N - BL71-UP
S/N - BY41-UP
S/N - DX21-UP
S/N - DX91-UP
S/N - FD21-UP
S/N - HP21-UP
S/N - MD21-UP
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 393-2572 Flywheel Stopper 1
Start By:
a. Remove the front housing.
1. Ensure that number four piston is at the top center position on the compression stroke. Refer
to Systems Operation, Testing and Adjusting, "Finding Top Center Position for No. 4
Piston".
1/2
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
23. Illustration 1 g06066040
2. Ensure that timing marks on the gears are aligned.
Alternatively, make temporary timing marks on the gears to show alignment.
3. Install Tooling (A) onto the flywheel. Remove bolts (2) and idler gear (3).
4. Remove nuts (1) and idler gear (4).
Installation Procedure
1. Install the idler gears in the reverse order of removal.
a. Tighten nuts (1) to a torque of 24 N·m to 27 N·m (212 lb in to 239 lb in).
b. Tighten bolts (2) to a torque of 24 N·m to 27 N·m (212 lb in to 239 lb in).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 30 23:58:16 UTC+0800 2019
2/2
299D2 and 299D2XHP Compact Track Loader BY400001-UP (MACHINE) POWER...
2019/10/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...