Diseñado para trabajos exigentes en aplicaciones de explanación, el tractor de ruedas 834G combina un aumento de potencia, movilidad y comodidad del operador para proporcionar un avance revolucionario en las topadoras. El 834G es ideal para movimiento de tierras, industrias y minería.
Brochure, Folleto, Specalog, oroscocatt, oroscocat
Catalogo 834G CAT pdf
¿Cuándo cambiar tus amortiguadores? ¿Cómo hacerlo? ¿Qué pasos necesitas seguir para realizar el cambio de tu amortiguador? Todos estos consejos y más con nuestro experto en mecánica.
Descubre todos los secretos para poder realizar el mantenimiento y el recambio de las piezas de tu coche tú mismo.
En esta presentación: Recambio de amortiguadores
¿Cuándo cambiar tus amortiguadores? ¿Cómo hacerlo? ¿Qué pasos necesitas seguir para realizar el cambio de tu amortiguador? Todos estos consejos y más con nuestro experto en mecánica.
Descubre todos los secretos para poder realizar el mantenimiento y el recambio de las piezas de tu coche tú mismo.
En esta presentación: Recambio de amortiguadores
Cuidado y mantenimiento de los NeumáticosOmarGarcia318
Conocimientos básicos de Neumáticos, construcción, cuidado y mantenimiento. Ladrones del Kilometraje, la importancia del mantenimiento preventivo de los neumáticos
ETIQUETAS DE SEGURIDAD CARGADOR FRONTALprof. deybis
La información básica y concreta de seguridad en cargador frontal como también de otras maquinas solo cambiamos el nombre de la maquina comenta si te gusta
<principios>
1. Compuestos del aceite lubricante
2. Tipos y funciones de aditivos
3. Tipos y funciones de aceites para maquinaria de construcción
4. Transición de recomendaciones para aceites lubricantes
5. Aceites y grasas a ser usados en maquinarias que cumplen con las regulaciones Tier 3
6. Ejemplo de falla debido al uso de aceites no recomendados por Komatsu
7. Ejemplo de resultado de prueba de bomba (Cuna/Cama de la bomba Pricipal))
8. Aceites recomendados
9. Ubicación de verificación/relleno de aceite y posición de filtros a ser reemplazados
10. Llenado de aceite en fábrica
Administración de tiempos de mantenimiento con el monitor de la máquina
<verificar>
12. Historia de aceites de motor
13. Use aceites genuinos series DH Komatsu como aceite de motor
14. Detergencia del aceite de motor
15. Uso de filtros genuinos Komatsu para filtración de aceites de motor
16. Combinación de filtros
17. Uso de repuestos genuinos Komatsu extiende el intervalo de cambio de aceite cada 500 horas
Verificación del nivel de aceite periódicamente! (Verifique puntos antes del arranque)
Asegúrese de seguir el intervalo de cambio de aceite especificado el Manual de O & M
Uso adecuado del aceite de motor
www.oroscocatt.com
Cuidado y mantenimiento de los NeumáticosOmarGarcia318
Conocimientos básicos de Neumáticos, construcción, cuidado y mantenimiento. Ladrones del Kilometraje, la importancia del mantenimiento preventivo de los neumáticos
ETIQUETAS DE SEGURIDAD CARGADOR FRONTALprof. deybis
La información básica y concreta de seguridad en cargador frontal como también de otras maquinas solo cambiamos el nombre de la maquina comenta si te gusta
<principios>
1. Compuestos del aceite lubricante
2. Tipos y funciones de aditivos
3. Tipos y funciones de aceites para maquinaria de construcción
4. Transición de recomendaciones para aceites lubricantes
5. Aceites y grasas a ser usados en maquinarias que cumplen con las regulaciones Tier 3
6. Ejemplo de falla debido al uso de aceites no recomendados por Komatsu
7. Ejemplo de resultado de prueba de bomba (Cuna/Cama de la bomba Pricipal))
8. Aceites recomendados
9. Ubicación de verificación/relleno de aceite y posición de filtros a ser reemplazados
10. Llenado de aceite en fábrica
Administración de tiempos de mantenimiento con el monitor de la máquina
<verificar>
12. Historia de aceites de motor
13. Use aceites genuinos series DH Komatsu como aceite de motor
14. Detergencia del aceite de motor
15. Uso de filtros genuinos Komatsu para filtración de aceites de motor
16. Combinación de filtros
17. Uso de repuestos genuinos Komatsu extiende el intervalo de cambio de aceite cada 500 horas
Verificación del nivel de aceite periódicamente! (Verifique puntos antes del arranque)
Asegúrese de seguir el intervalo de cambio de aceite especificado el Manual de O & M
Uso adecuado del aceite de motor
www.oroscocatt.com
El Tractor Topador de Ruedas 844 se ha diseñado para usar en trabajos exigentes de explanación, es el más grande de la gama de tractores de ruedas Caterpillar y es ideal para trabajar en aplicaciones grandes de minera, generación de corriente eléctrica,la industria de construcción general y donde quiera que se necesiten movilidad y explanación a gran volumen.
Brochure, Folleto,Specalog, oroscocatt, oroscocat
catalogo 390 d
Alto nivel de producción sostenida, mejorado.
Incremento de rendimiento, fiabilidad y durabilidad.
Su productividad y disminuir sus costos operativos.
El Tractor Topador de Ruedas 834H se ha diseñado para usar en trabajos exigentes de explanación, es el más grande de la gama de tractores de ruedas Caterpillar y es ideal para trabajar en aplicaciones grandes de minera, generación de corriente eléctrica,la industria de construcción general y donde quiera que se necesiten movilidad y explanación a gran volumen.
El Tractor Topador de Ruedas 854G se ha diseñado para usar en trabajos exigentes de explanación, es el más grande de la gama de tractores de ruedas Caterpillar y es ideal para trabajar en aplicaciones grandes de minera, generación de corriente eléctrica,la industria de construcción general y donde quiera que se necesiten movilidad y explanación a gran volumen.
Los manuales de operación y mantenimiento incluyen información de operación, mantenimiento, seguridad y servicio.
El manual de servicio incluye información sobre cómo funcionan los sistemas operativos importantes, las pruebas, las guías de ajustes y solución de problemas, así como también, los procedimientos de desarmado y armado.
El manual de piezas tiene vistas en detalle de todas las piezas de servicio del equipo. También le ofrece una guía con números para pedir piezas genuinas Caterpillar.
Brochure de especificaciones -
Los minicargadores Cat® son líderes en la industria
respecto al rendimiento, versatilidad y comodidad del
operador. Dentro de la espaciosa estación del operador,
sienta la comodidad superior de una cabina sellada y
presurizada. Siéntase cómodo durante el día de trabajo
gracias a los controles ajustables montados en el asiento
y el asiento con amortiguación neumática. Mejore el
rendimiento y aumente el resultado final con mayores
capacidades nominales de operación, mayor potencia
y rendimiento mejorado de la barra de tiro.
Brochure, Folleto,Specalog, oroscocatt, oroscocat
El Tractor Topador de Ruedas 854G se ha diseñado para usar en trabajos exigentes de explanación, es el más grande de la gama de tractores de ruedas Caterpillar y es ideal para trabajar en aplicaciones grandes de minera, generación de corriente eléctrica,la industria de construcción general y donde quiera que se necesiten movilidad y explanación a gran volumen.
Brochure, Folleto,Specalog, oroscocatt, oroscocat
El Cargador de Ruedas L-2350 es fabricada por LeTourneau y es actualmente la mayor Cargadora de este tipo que se fabrica en serie en el mundo. Es utilizada principalmente en grandes minas y está especialmente diseñada para trabajar con camiones de carga cuya capacidad llega a las 350 – 400 toneladas, como el Liebherr T 282 B.
Se fabrica con dos opciones de motor: La Detroit Diesel serie 4000 y la Cummins OSK60.
En su cucharón caben mas de 40 metros cúbicos (53 yds3 - 70 yds3) de material y levanta hasta 72 toneladas pudiendo descargarlas a una altura de 7 metros y medio.
Esta máquina diesel-eléctrica lleva un sistema de tracción formado por un motor diesel, generador de corriente alterna y tracción eléctrica por motores en las ruedas, típico del fabricante Americano.
El manual de servicio incluye información sobre cómo funcionan los sistemas operativos importantes, las pruebas, las guías de ajustes y solución de problemas, así como también, los procedimientos de desarmado y armado.
El manual de piezas tiene vistas en detalle de todas las piezas de servicio del equipo. También le ofrece una guía con números para pedir piezas genuinas Caterpillar.
El manual de servicio incluye información sobre cómo funcionan los sistemas operativos importantes, las pruebas, las guías de ajustes y solución de problemas, así como también, los procedimientos de desarmado y armado.
El manual de piezas tiene vistas en detalle de todas las piezas de servicio del equipo. También le ofrece una guía con números para pedir piezas genuinas Caterpillar.
El manual de servicio incluye información sobre cómo funcionan los sistemas operativos importantes, las pruebas, las guías de ajustes y solución de problemas, así como también, los procedimientos de desarmado y armado.
El manual de piezas tiene vistas en detalle de todas las piezas de servicio del equipo. También le ofrece una guía con números para pedir piezas genuinas Caterpillar.
El manual de servicio incluye información sobre cómo funcionan los sistemas operativos importantes, las pruebas, las guías de ajustes y solución de problemas, así como también, los procedimientos de desarmado y armado.
El manual de piezas tiene vistas en detalle de todas las piezas de servicio del equipo. También le ofrece una guía con números para pedir piezas genuinas Caterpillar.
El manual de servicio incluye información sobre cómo funcionan los sistemas operativos importantes, las pruebas, las guías de ajustes y solución de problemas, así como también, los procedimientos de desarmado y armado.
El manual de piezas tiene vistas en detalle de todas las piezas de servicio del equipo. También le ofrece una guía con números para pedir piezas genuinas Caterpillar.
El manual de servicio incluye información sobre cómo funcionan los sistemas operativos importantes, las pruebas, las guías de ajustes y solución de problemas, así como también, los procedimientos de desarmado y armado.
El manual de piezas tiene vistas en detalle de todas las piezas de servicio del equipo. También le ofrece una guía con números para pedir piezas genuinas Caterpillar.
Las perfiladoras de pavimentos en frío Cat® colocan toneladas de material en los camiones una hora tras otra y un turno tras otro. La producción no solo es cuestión de potencia. Se trata de cómo la perfiladora suministra dicha potencia al rotor. Los sistemas de accionamiento del rotor Cat son los más eficientes y mejor protegidos del sector. El control de carga Cat ofrece la máxima fiabilidad y mantiene el régimen del motor próximo al par máximo siempre que el corte presenta resistencia.Las cuchillas de corte Cat duran más para aumentar el tiempo de actividad y la productividad. Las superficies fresadas limpias se dejan atrás gracias al control preciso de la presión de la hoja vertedera. La opción Cat Grade and Slope está disponible para todos los requisitos de las aplicaciones.
More from Corporación www.oroscocat.com - Maquinaria Pesada.org (20)
Final project report on grocery store management system..pdfKamal Acharya
In today’s fast-changing business environment, it’s extremely important to be able to respond to client needs in the most effective and timely manner. If your customers wish to see your business online and have instant access to your products or services.
Online Grocery Store is an e-commerce website, which retails various grocery products. This project allows viewing various products available enables registered users to purchase desired products instantly using Paytm, UPI payment processor (Instant Pay) and also can place order by using Cash on Delivery (Pay Later) option. This project provides an easy access to Administrators and Managers to view orders placed using Pay Later and Instant Pay options.
In order to develop an e-commerce website, a number of Technologies must be studied and understood. These include multi-tiered architecture, server and client-side scripting techniques, implementation technologies, programming language (such as PHP, HTML, CSS, JavaScript) and MySQL relational databases. This is a project with the objective to develop a basic website where a consumer is provided with a shopping cart website and also to know about the technologies used to develop such a website.
This document will discuss each of the underlying technologies to create and implement an e- commerce website.
COLLEGE BUS MANAGEMENT SYSTEM PROJECT REPORT.pdfKamal Acharya
The College Bus Management system is completely developed by Visual Basic .NET Version. The application is connect with most secured database language MS SQL Server. The application is develop by using best combination of front-end and back-end languages. The application is totally design like flat user interface. This flat user interface is more attractive user interface in 2017. The application is gives more important to the system functionality. The application is to manage the student’s details, driver’s details, bus details, bus route details, bus fees details and more. The application has only one unit for admin. The admin can manage the entire application. The admin can login into the application by using username and password of the admin. The application is develop for big and small colleges. It is more user friendly for non-computer person. Even they can easily learn how to manage the application within hours. The application is more secure by the admin. The system will give an effective output for the VB.Net and SQL Server given as input to the system. The compiled java program given as input to the system, after scanning the program will generate different reports. The application generates the report for users. The admin can view and download the report of the data. The application deliver the excel format reports. Because, excel formatted reports is very easy to understand the income and expense of the college bus. This application is mainly develop for windows operating system users. In 2017, 73% of people enterprises are using windows operating system. So the application will easily install for all the windows operating system users. The application-developed size is very low. The application consumes very low space in disk. Therefore, the user can allocate very minimum local disk space for this application.
Saudi Arabia stands as a titan in the global energy landscape, renowned for its abundant oil and gas resources. It's the largest exporter of petroleum and holds some of the world's most significant reserves. Let's delve into the top 10 oil and gas projects shaping Saudi Arabia's energy future in 2024.
Industrial Training at Shahjalal Fertilizer Company Limited (SFCL)MdTanvirMahtab2
This presentation is about the working procedure of Shahjalal Fertilizer Company Limited (SFCL). A Govt. owned Company of Bangladesh Chemical Industries Corporation under Ministry of Industries.
About
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Technical Specifications
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
Key Features
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface
• Compatible with MAFI CCR system
• Copatiable with IDM8000 CCR
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
Application
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Courier management system project report.pdfKamal Acharya
It is now-a-days very important for the people to send or receive articles like imported furniture, electronic items, gifts, business goods and the like. People depend vastly on different transport systems which mostly use the manual way of receiving and delivering the articles. There is no way to track the articles till they are received and there is no way to let the customer know what happened in transit, once he booked some articles. In such a situation, we need a system which completely computerizes the cargo activities including time to time tracking of the articles sent. This need is fulfilled by Courier Management System software which is online software for the cargo management people that enables them to receive the goods from a source and send them to a required destination and track their status from time to time.
Automobile Management System Project Report.pdfKamal Acharya
The proposed project is developed to manage the automobile in the automobile dealer company. The main module in this project is login, automobile management, customer management, sales, complaints and reports. The first module is the login. The automobile showroom owner should login to the project for usage. The username and password are verified and if it is correct, next form opens. If the username and password are not correct, it shows the error message.
When a customer search for a automobile, if the automobile is available, they will be taken to a page that shows the details of the automobile including automobile name, automobile ID, quantity, price etc. “Automobile Management System” is useful for maintaining automobiles, customers effectively and hence helps for establishing good relation between customer and automobile organization. It contains various customized modules for effectively maintaining automobiles and stock information accurately and safely.
When the automobile is sold to the customer, stock will be reduced automatically. When a new purchase is made, stock will be increased automatically. While selecting automobiles for sale, the proposed software will automatically check for total number of available stock of that particular item, if the total stock of that particular item is less than 5, software will notify the user to purchase the particular item.
Also when the user tries to sale items which are not in stock, the system will prompt the user that the stock is not enough. Customers of this system can search for a automobile; can purchase a automobile easily by selecting fast. On the other hand the stock of automobiles can be maintained perfectly by the automobile shop manager overcoming the drawbacks of existing system.
NO1 Uk best vashikaran specialist in delhi vashikaran baba near me online vas...Amil Baba Dawood bangali
Contact with Dawood Bhai Just call on +92322-6382012 and we'll help you. We'll solve all your problems within 12 to 24 hours and with 101% guarantee and with astrology systematic. If you want to take any personal or professional advice then also you can call us on +92322-6382012 , ONLINE LOVE PROBLEM & Other all types of Daily Life Problem's.Then CALL or WHATSAPP us on +92322-6382012 and Get all these problems solutions here by Amil Baba DAWOOD BANGALI
#vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore#blackmagicformarriage #aamilbaba #kalajadu #kalailam #taweez #wazifaexpert #jadumantar #vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore #blackmagicforlove #blackmagicformarriage #aamilbaba #kalajadu #kalailam #taweez #wazifaexpert #jadumantar #vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore #Amilbabainuk #amilbabainspain #amilbabaindubai #Amilbabainnorway #amilbabainkrachi #amilbabainlahore #amilbabaingujranwalan #amilbabainislamabad
Vaccine management system project report documentation..pdfKamal Acharya
The Division of Vaccine and Immunization is facing increasing difficulty monitoring vaccines and other commodities distribution once they have been distributed from the national stores. With the introduction of new vaccines, more challenges have been anticipated with this additions posing serious threat to the already over strained vaccine supply chain system in Kenya.
Cosmetic shop management system project report.pdfKamal Acharya
Buying new cosmetic products is difficult. It can even be scary for those who have sensitive skin and are prone to skin trouble. The information needed to alleviate this problem is on the back of each product, but it's thought to interpret those ingredient lists unless you have a background in chemistry.
Instead of buying and hoping for the best, we can use data science to help us predict which products may be good fits for us. It includes various function programs to do the above mentioned tasks.
Data file handling has been effectively used in the program.
The automated cosmetic shop management system should deal with the automation of general workflow and administration process of the shop. The main processes of the system focus on customer's request where the system is able to search the most appropriate products and deliver it to the customers. It should help the employees to quickly identify the list of cosmetic product that have reached the minimum quantity and also keep a track of expired date for each cosmetic product. It should help the employees to find the rack number in which the product is placed.It is also Faster and more efficient way.
Forklift Classes Overview by Intella PartsIntella Parts
Discover the different forklift classes and their specific applications. Learn how to choose the right forklift for your needs to ensure safety, efficiency, and compliance in your operations.
For more technical information, visit our website https://intellaparts.com
Democratizing Fuzzing at Scale by Abhishek Aryaabh.arya
Presented at NUS: Fuzzing and Software Security Summer School 2024
This keynote talks about the democratization of fuzzing at scale, highlighting the collaboration between open source communities, academia, and industry to advance the field of fuzzing. It delves into the history of fuzzing, the development of scalable fuzzing platforms, and the empowerment of community-driven research. The talk will further discuss recent advancements leveraging AI/ML and offer insights into the future evolution of the fuzzing landscape.
Catalogo del Tractor de Ruedas 834G (ingles) - www.oroscocat.com
1. ®®
Engine
Engine Model Cat
®
3456 Diesel
Gross Power 392 kW 525 hp
Flywheel Power 359 kW 481 hp
Blade Specifications
Blade Capacities 7.9 to 22.2 m
3
10.3 to 29 yd3
Weights
Operating Weight 47 106 kg 103,849 lb
834G
Wheel Dozer
2. 2
834G Wheel Dozer
Strong power train combined with a heavy-duty front frame provides extended life
and economical operation.
Engineered for demanding work in large
dozing applications, the 834G Wheel Dozer
combines increased power, mobility and
operator comfort to provide a revolutionary
advancement in the large wheel dozer
design. The 834G is ideally suited for the
rigorous earth moving duties in the mining
and contracting industries.
Customer Support
Your Cat dealer offers a wide range of
services that help you operate longer
with lower costs. pg. 13
Structures
The 834G features a box-section,
engine-end frame and two-plate, front
frame. These structures resist shock
loads while absorbing twisting forces
for improved frame alignment and
stability. pg. 8
Hydraulics
Innovative electro-hydraulics play a
key role in performance and provide
low operator effort. Increased hydraulic
efficiency improves blade response.
pg. 6
Power Train
The Cat 3456 EUI diesel engine is Tier 2
compliant. A new cylinder block is
stronger and lighter. The Caterpillar
®
planetary power shift transmission
and impeller clutch torque converter
provide smooth, consistent shifting
with fingertip control. Electronic
controls contribute to increased
levels of productivity. pg. 4
✔
3. ✔ New Feature
3
Serviceability
Most daily maintenance checks are
performed from the 834G’s left side
to facilitate quick start up. Case drain
filtration is standard and uptime is
increased with 500 hour oil change
intervals. pg. 12
Operator Station
Experience a new level of efficiency
and comfort with one-hand STIC
controller operation, a 38 percent larger
cab, fingertip blade controls, improved
range of viewing, reduced sound levels
and improved ventilation. pg. 10
Blades
Choose a straight blade, universal blade
or coal blade. Replaceable, bolt-on
cutting edges and welded-on bottom
wear plates help extend blade life.
pg. 9
4. 1 Caterpillar 3456 Diesel Engine. Is based
on one of the most successful engines
offered by Caterpillar, the 3406E. The
3456 is Tier 2 compliant and features
increased horsepower and efficient fuel
management for quick response, high
productivity and exceptional service life.
A new, sculptured cylinder block provides
greater strength and is lighter weight.
• 49 Percent Torque Rise. Provides
high lugging force during dozing and
acceleration in high rimpull conditions.
The torque curve effectively matches
the transmission shift points to provide
maximum efficiency and faster
cycle times.
• Pistons. Three-ring, aluminum alloy
which are cam-ground, tapered and
cooled by oil spray.
• Crankshaft Bearings. Steel backed,
copper-bonded.
• Pressure Lubricated. With full-flow
filtered and cooled oil.
• Starting System. Direct-electric, 24-volt
with ether, 75-amp alternator and two
12-volt, 190 amp-hour batteries.
• Electronic Unit Injection (EUI). Is a
proven high-pressure, direct injection
fuel system that electronically monitors
operator demands and sensor inputs to
optimize engine performance.
• Air Cleaners. Are dry-type radial seal
with primary and secondary elements
and precleaner.
• ADEM™ III (Advanced Diesel Engine
Management III) System . Controls the
fuel injector solenoids to start and stop
fuel injection. This system provides
automatic altitude compensation, air
filter restriction indication and will
not allow the engine to fire until it
has oil pressure, acting as a cold start
protection and a form of pre-lube.
Includes cold weather starting mode,
elevated low idle, advanced diagnostic
capabilities, automatic altitude deration
and automatic ether aid control.
• Air to Air Aftercooler (ATAAC) System.
Provides a separate cooling system for
the intake manifold air. The ATAAC
system routes hot compressed air from
the turbo and cools it with a single pass,
air-to-air aluminum heat exchanger.
The cooled, compressed air greatly
reduces the emissions produced,
meeting Tier 2 requirements.
• Airflow matched turbocharger with
power rating helps reduce emissions.
• 19 percent more bearing area allows
the engine to operate at the maximum
cylinder pressure.
• Higher cylinder pressure capability
helps reduce fuel consumption and
improves high altitude operation.
• Cylinder head exhaust port sleeves
reduce heat rejection which results
in less heat transfer into the water
jacket system.
2 Separate Engine Cooling System.
Isolates the radiator and fan from the
engine compartment for more efficient
cooling and allows for a sloped hood
for increased viewing.
4
The 834G power train components deliver dependable, reliable performance customers
expect from Cat Wheel Dozers.
Power Train
1
42 3
5
6
5. Advanced Modular Cooling System
(AMOCS). Improves cooling capabilities
by using a parallel flow system with
10 cores. Serviceability is improved
with AMOCS as there is no top tank
to remove.
3 Electronically Controlled Caterpillar
Planetary Power Shift Transmission.
Features perimeter-mounted, large
diameter clutch packs that control inertia
for smooth shifting and increased
component life. It can be recalibrated
using the Electronic Technician (ET)
Service Tool.
• Parking Brake. Is spring-applied, oil-
released and dry disc. It is mounted on
the transmission transfer gear output
shaft. Manual override is possible to
allow movement of the machine.
4 Impeller Clutch Torque Converter.
Combined with the Rimpull Control
System (RCS) allows the operator
maximum flexibility in modulating
rimpull.
• The torque converter is equipped
with a standard lock-up clutch for
direct drive efficiency.
• Improved calibration procedure
• Improved left pedal modulation
• Compensates for wear by providing
the ability to recalibrate for optimum
left pedal modulation regardless of
torque converter wear
• Left pedal control allows the operator
to reduce rimpull from 100 percent
to 20 percent while maintaining high
engine speed for slower work without
losing power. After 20 percent, further
pedal travel applies the brake.
• RCS allows the operator to select
from four preset rimpull settings
(low, medium, high and maximum).
5 Heavy-Duty Axles. Feature optional axle
oil coolers, permanently lubed universal
joints and stronger axle components in
both the differentials and final drives for
increased performance, serviceability
and durability. Conventional differential
is standard.
• Final Drives. Feature planetary reduction
at each wheel. Torque is developed at
the wheel, which gives less stress at the
axle shafts. The planetary units are oil-
bath lubricated and can be removed
independently from the wheels and
brakes. Ring gears are spleened to the
axle housing. Proprietary gear cutting
and head treating methods are used in
the manufacturing and bronze thrust
washers interface with the sun gear/
bearing retainer.
• Free-Floating Axle Shafts. Can be
removed independent of the wheels
and planetaries for quick and easy
serviceability.
• Optional Axle Oil Cooling System.
Features two circuits that circulate oil
from the differentials through an oil-to-
air cooler and a filter back to the brakes.
This system provides increased oil life
and improves component performance
and durability. The system automatically
turns on and off at a preset oil temperature.
6 Axle-Shaft, Oil Disk Brakes. Are
adjustment-free, fully hydraulic and
completely sealed. Disc face grooves
provide cooling, even when brakes
are applied, for a long, fade-resistant
service life.
• Location of the brakes improves
serviceability. The axle-shaft brake
design allows brake service while
leaving the final drive intact.
• Axle-shaft brakes require less force
by operating on the low torque side
of the axle. Combined with improved
axle oil circulation for increased
cooling, the oil-enclosed, multiple-
disc brake design improves durability.
• Service Brakes. Are four wheel,
hydraulic, oil dipped multiple disc
brakes that are adjustment-free,
completely enclosed and allow
modulated engagement without
slack adjusters.
• Secondary Brakes. Are fully modulated
and the front and rear service brake
circuits are isolated so one circuit
can operate if pressure drops in the
other circuit.
Brakes(20%Rimpull)
100% Rimpull
Selected
Left Pedal
20% Rimpull
Selected
5
6. 1 Electro-Hydraulic Control System.
Increases hydraulic efficiency and
enhances operator comfort through
low-effort fingertip controls. XT-3
and XT-5 hose combine with reliable
components to help reduce the risk
of leaks and blowing lines.
2 Blade Control. A floor mounted
single-lever, fingertip control for
lift/lower/tilt/tip sends electronic signals
to a main hydraulic valve positioned
outside the cab. This eliminates sound,
heat and control effort associated with
in-cab hydraulic valve systems.
Tilt/Tip Circuit. Features fingertip
control for ease of operation.
Lift circuit features:
• Four positions: raise, hold, lower
and float
• Detente hold on float
Case Drain Filtration. The 834G has two
case drain filters that protect the steering
and fan pumps from contamination with
easy access for service.
6
Well-balanced hydraulics deliver precise, low-effort control and trouble-free operation.
Hydraulics
1
2
3
7. 3 Load Sensing Steering. With the STIC
control system, integrates steering and
transmission into a single controller.
The steering system utilizes a variable
displacement pump for maximum
machine performance by directing
power through the steering system
only when needed.
Features. Include center-point frame
articulation, front and rear wheel
tracking and floor-mounted and
adjustable armrests for a full range
of comfort adjustments.
Caterpillar Monitoring System
(EMS-III). Continually monitors various
machine systems through three instrument
clusters and provides a three-level
warning system to alert the operator of
immediate or pending problems. It shares
information with the engine, hydraulic
and transmission controls that can be
used during servicing to simplify service
and troubleshooting. The Caterpillar
Monitoring System allows for new
software to be uploaded in the cab.
Demand Fan. Is a speed controlled,
hydraulic fan that provides maximum
cooling efficiency by directing the
appropriate amount of power through
the fan system based on coolant
temperature.
7
8. Structure Construction. Combines the use
of robotic welding on up to 90 percent
of the 834G while castings in several
areas to increase strength by helping to
spread the loads and reduce the number
of parts. This provides highly consistent
welds with deep plate penetration and
excellent plate fusion. The benefit is
increased durability and fatigue strength.
The computer controlled machining
ensures the alignments of pin bore, axle
pad, cab mount and transmission/engine
components.
1 Box-Section Engine End-Frame.
Is designed to resist twisting and
torsional forces and to provide a
solid foundation for axles, engine
and transmission.
2 Two-Plate Front Frame. Provides
maximum structural strength during
dozing applications for improved stability.
3 Spread-Hitch Design. Is large
and improves load distribution by
reducing loads to the hitch bearings.
The large center hitch design improves
hydraulic line routing and makes service
access easier.
Upper and Lower Hitch Pins. Pivot on
double-tapered roller bearings. Box-style
sections in the hitch pins and cross
member assembly improve strength
of the frame structure.
Engine and Transmission Mounts. Use a
rubber, mushroomed, cup-shaped design
to reduce noise and vibration.
Frame Design. Straight side rail design
improves torsional strength, shock load
absorption and frame alignment. It is
specifically designed with fewer parts
to improve quality and reliability.
8
Structures
Advanced design and materials provide superior strength.
1
2
3
9. Caterpillar Blades. Are resilient and
durable and designed with excellent
dozing and rolling characteristics.
• Capacities and widths are set to
achieve increased productivity.
• Special design allows for spreading
of cover material as well as dozing
of heavier loads.
• High-strength, pressed rib
construction.
• Large, bolt-on cutting edges are
DH-2 steel. End bits are DH-3 to
provide maximum service life in
tough materials.
• Blades are fitted with Caterpillar
standard hardware and Ground
Engaging Tools (G.E.T.).
• Cat blades are rebuildable for
extended service life.
9
Blades
Caterpillar blades are available to match many dozing requirements.
1 Straight Blade. Is designed for production dozing in
stockpiled material and general earthmoving.
3 Coal Blade. Is designed for precise and productive
dozing while helping to retain load control with increased
capacity for lighter materials. Wing angles help retain the
load while dozing.
Assemblies. For the straight blade and universal blade
consist of the blade, push arms, hydraulic lift, tip and tilt
cylinders, trunnion mounting and hydraulic line guards.
2 Universal Blade. Is designed for moving large loads over
long distances in mining applications.
2
1 3
10. 10
A new industry standard for comfort and efficiency.
Operator Station
1
2
13
3
4
5
6
12
7
11. World Class Cab. With over 3.18 m
3
(112 ft
3
) of volume incorporates
innovations for operator comfort,
maneuverability and productivity.
Features include outstanding viewing
area, improved cab ventilation, interior
sound levels below 77 dB(A), standard
coat hook, cup holder, storage bin,
intermittent wet-arm wipers, room for a
large lunch cooler and radio-readiness.
1 STIC Control System. Combines gear
selection and steering into one control
lever that requires less effort and
provides smooth shifting. Side-to-side
motions for steering, finger operated
direction control and thumb operated
buttons for gear selection combine to
provide a fluid motion that reduces
effort and allows the operator to work
the machine for long periods of time
with little or no fatigue.
2 Left Pedal. Operates the Impeller
Clutch Torque Converter. Within the
first one and a half inches of pedal
travel, rimpull can be controlled
from 100 percent to 20 percent.
Fully depressing the pedal applies
the brake. The right pedal allows
standard braking.
3 Comfort Series Seat. With air
suspension and retractable seat belt
is designed for increased comfort and
support. Seat cushions reduce pressure
on the lower back and thighs while
allowing increased arm and leg
movement.
4 Electro-Hydraulic Blade Controls.
Are adjustable fore and aft, with a
height-adjustable armrest so operators
of any size can find a comfortable
position. Single lever control allows
operator to control blade functions:
lift/lower, tip and tilt.
5 Tilt/Tip Switch. Allows operators to
select tilt or tip control for dozing.
6 Caterpillar Monitoring System
(EMS-III). Provides information on
the machine’s major components
and systems.
• Gauges display fuel tank level and
temperatures for engine coolant,
power train and hydraulic oil.
The tachometer is an analog
gauge with digital readout for
gear selection and ground speed.
• The main module consists of ten
fault indicators and one display
panel. Alerts occur for engine oil
pressure, parking brake status,
brake oil pressure, charging system,
coolant flow status, hydraulic filter
status, steering pressure, axle oil
temperature, engine overspeed,
machine hours, digital engine
speed, odometer and faults.
• Alerts the operator if transmission
is engaged while parking brake is
applied or if pressure drops, the
brake is applied.
7 Throttle Lock. Allows the operator to
pre-set the engine speed for a variety
of applications, resulting in faster cycle
times and increased productivity.
8 Rimpull Control System (RCS). Has four
factory preset rimpull settings (low,
medium, high and maximum) to better
match ground conditions.
9 Autoshift. Allows the operator to
set the maximum gear into which the
transmission will be allowed to shift.
This feature allows additional comfort
and focus on the job. The switch also
offers a manual position for operator
controlled shifting.
10 Lock-Up Clutch Torque Converter
Switch. Activates lock-up clutch for
direct drive efficiency.
11 Front and Rear Window Wiper/
Washers. Are within easy reach to
maintain a clear field of vision.
12 Viewing Area. Is improved with a
bonded front windshield that eliminates
distracting metal frames for excellent
bucket and work site visibility. An
internal ROPS improves peripheral
viewing by eliminating the large
structure outside the cab.
13 Electro-Hydraulic Lock-Out Switch.
Disables hydraulic controls.
11
10
8
11
119
Upper Left Console
Upper Right Console
12. Easy Maintenance. In addition to the
servicing features built into the engine,
the 834G includes:
• Rear Access Stairs and Standard Left-
Hand Stairway. For easy, comfortable
access for operators and service
personnel.
• Large Engine Access Doors. Provide
excellent access to service points: engine
oil dipstick, diagnostic connector, engine
oil and fuel filters, starting receptacle,
air filter indicator, air filters, fuel/water
separator and the ether starting aid
cartridge.
• Service Platform. Provides passage
to the hydraulic filter through easy-to-
open doors.
• Large Door. Provides entrance to the
transmission and pumps when service
is required.
• Platform Door. Provides access to
fuses and electronic control modules.
• Batteries. Are accessible through
hinged doors in the bumper.
• Caterpillar Monitoring System
(EMS-III). Allows for flashable software.
• Side Access Doors. On the radiator
guard provide easy access for radiator
cleanout.
• Lube Points. Are grouped, labeled and
accessible at ground level to make daily
lube maintenance quick and easy.
• Sight Gauges. In the hydraulic
tanks and radiator provide quick
fluid level checks.
• Ground Level Engine Shut-Off.
And electrical disconnect switches
are standard.
• Oil Change Interval. 500 hours with
CH-4 oil.
• Brakes. With axle-shaft design that
allows service while leaving the final
drive intact.
12
Serviceability
Simplified service means more production time.
13. Machine Selection. Make detailed
comparisons of the machines under
consideration before purchase.
Cat dealers can estimate component
life, preventative maintenance cost
and the true cost of lost production.
Purchase. Look past initial price.
Consider the financing options available
as well as the day-to-day operating
costs. Look at dealer services that can
be included in the cost of the machine
to yield lower equipment owning and
operating costs over the long run.
Customer Support Agreements.
Cat dealers offer a variety of product
support agreements and work with
you to develop a plan that best meets
specific needs. These plans can cover
the entire machine, including work
tools, to help protect your investment.
Product Support. You will find nearly
all parts at our dealer parts counter.
Cat dealers use a world-wide computer
network to find in-stock parts to minimize
machine down time. Save money with
genuine Cat Remanufactured parts.
You receive the same warranty and
reliability as new products at cost
savings of 40 to 70 percent.
Operation. Improving operating
techniques can boost profits. Your Cat
dealer has training videotapes, literature
and other ideas to help increase
productivity.
Maintenance Services. More and
more equipment buyers are planning
for effective maintenance before buying
equipment. Choose from your dealer’s
wide range of maintenance services at
the time you purchase your machine.
Repair option programs guarantee the
cost of repairs up front. Diagnostic
programs such as S·O·S
SM
and Coolant
Sampling and Technical Analysis help
you avoid unscheduled repairs.
Replacement. Repair, rebuild or replace?
Your Cat dealers can help you evaluate
the costs involved so you can make the
right choice.
13
Customer Support
Cat dealer services help keep machine operating longer with lower costs.
14. 14 834G Wheel Dozer specifications
Transmission
Number of Forward Speeds 4
Number of Reverse Speeds 3
Converter Drive - Forward 1 6.7 kph 4.2 mph
Converter Drive - Forward 2 11.8 kph 7.3 mph
Converter Drive - Forward 3 20.6 kph 12.8 mph
Converter Drive - Forward 4 35.8 kph 22.3 mph
Converter Drive - Reverse 1 7 kph 4.4 mph
Converter Drive - Reverse 2 12.3 kph 7.7 mph
Converter Drive - Reverse 3 21.6 kph 13.4 mph
Direct Drive - Forward 1 Lock-up Disabled in
Forward 1
Direct Drive - Forward 2 12.3 kph 7.7 mph
Direct Drive - Forward 3 21.9 kph 13.6 mph
Direct Drive - Forward 4 38.7 kph 24.1 mph
Direct Drive - Reverse 1 7.2 kph 4.5 mph
Direct Drive - Reverse 2 12.9 kph 8 mph
Direct Drive - Reverse 3 23 kph 14.3 mph
• Travel speeds based on two percent rolling resistance and
35/65-33 L-4 tires.
Hydraulic System
Gear pump output
at 1,900 rpm and 24,000 kPa 188 L/min 49.7 gal/min
(3,480 psi)
Lift cylinder, bore and stroke 139.75 mm 5.5 in
x 1021 mm x 40.2 in
Steering cylinder, bore 114.3 mm 4.5 in
and stroke x 740 mm x 29.1 in
Right tilt and tip, bore 152.4 mm 6 in
and stroke x 276 mm x 10.9 in
Left tilt and tip, bore 139.75 5.5 in
and stroke x 276 mm x 10.9 in
Relief valve setting 29 000 kPa 4,206 psi
Engine
Engine Model Cat 3456 Diesel
Gross Power 392 kW 525 hp
Flywheel Power 359 kW 481 hp
Direct Drive Net Power - 336 kW 451 hp
Caterpillar
Direct Drive Net Power - 336 kW 451 hp
EEC 80/1269
Direct Drive Net Power - 336 kW 451 hp
ISO 9249
Direct Drive Net Power - 333 kW 446 hp
SAE J1349 (JAN90)
Converter Drive Net Power - 359 kW 481 hp
Caterpillar
Converter Drive Net Power - 359 kW 481 hp
EEC 80/1269
Converter Drive Net Power - 359 kW 481 hp
ISO 9249
Converter Drive Net Power - 355 kW 477 hp
SAE J1349 (JAN90)
Bore 140 mm 5.5 in
Stroke 171 mm 6.75 in
Displacement 15.8 L 966 in
3
• These ratings apply at 1,900 rpm when tested under the
specific standard conditions for the specified standard.
• Power rating conditions based on standard air conditions
at 25° C (77° F) and 99 kPa (29.32 in Hg) dry barometer,
using 35° API gravity fuel having an LHV of 42 780 kJ/kg
(18,390 Btu/lb) when used at 30° C (86° F) [reference a
fuel density of 838.9 g/L (7.001 lb/gal)].
• Net power advertised is the power available (at the flywheel)
when the engine is equipped with air cleaner, muffler,
alternator and hydraulic fan drive.
• No derating required up to 2286 m (7,500 ft) altitude.
• Engine is Tier 2 emissions compliant.
0 4 10 14 20 24
Machine Ground Speed (mph)
0 4 8 12 16 20 24 28 32 36 km/h
mph
40
2 6 8 12 16 18 22
35
40
45
30
25
20
15
10
5
2
50
55
60
Rimpull(lbf)
70
80
90
60
50
40
30
20
10
0
lbs x
1000
kg x
1000
35
40
30
25
20
15
10
5
0
TotalResistance(%)
(Grade+Rolling)
1
2
3
4
4L
2L
3L
15. 15834G Wheel Dozer specifications
Cab
Cab ROPS/FOPS is standard.
Sound Performance Levels Meets ANSI/SAE, SAE and
ISO standards.
ROPS/FOPS Meets SAE and ISO
standards.
• Integrated Rollover Protection Structure (ROPS) and Falling
Object Protection System (FOPS) is standard.
• Standard air conditioning system contains R-134A refrigerant.
• The operator sound exposure Leq (equivalent sound pressure
level) measured according to the work cycle procedures
specified in ANSI/SAE J1166 OCT98 is 77 dB(A) for the cab
offered by Caterpillar when properly installed and maintained
and tested with the doors and windows closed.
• Hearing protection may be needed when operating with an
open operator station and cab (when not properly maintained
or doors/windows open) for extended periods or in noisy
environment.
• The exterior sound pressure level for the standard machine
measured at a distance of 15 meters (49.2 ft) according to
the test procedures specified in SAE J88 JUN86, mid-gear-
moving operation is 82 dB(A).
• The sound power level is 115 dB(A) measured according
to the dynamic test procedure and conditions specified
in ISO 6395:1988/Amd.1:1996 for a standard machine
configuration.
• For “CE” marked configurations, the labeled sound power
level is 113 dB(A) measured according to the test procedures
and conditions specified in 2000/14/EC.
• ROPS meets SAE J1394, SAE J1040 APR88, ISO 3471-1:1986
and ISO 3471:1994.
• FOPS meets SAE J231 JAN81 and ISO 3449-1992 LEVEL II.
Brakes
Brakes Meet SAE/ISO 3450 1996
Axles
Front Fixed axle
Rear Oscillating ±13°
Maximum single-wheel rise 448.3 mm 17.6 in
and fall
Steering
Steering Meets SAE J1511
FEB94/ISO 5010:1992
standards
Turning radius with straight 8899 mm 29.2 ft
blade
Tires
Standard Tire Size
Tires Four choices with
others on request.
• 35/65-33 L-4
35/65-33 L-5
35/65 R33 L-4
35/65 R33 L-5
• Caterpillar recommends that you consult a tire supplier
to evaluate all conditions before selecting a tire model.
Other special tires are available on request.
Weights
Operating Weight 47 106 kg 103,849 lb
Service Refill Capacities
Fuel Tank - standard 795 L 210 gal
Cooling system 94 L 25 gal
Crankcase 60 L 15.9 gal
Transmission 72 L 19 gal
Hydraulic tank 140 L 37 gal
Differentials and final drives 186 L 49.1 gal
– Front
Differentials and final drives 186 L 49.1 gal
– Rear
16. 4104 mm
(13' 5")
2275 mm
(7' 6")
4550 mm
(14' 11")
Straight Blade
9883 mm
(32' 5")
U Blade
10 417 mm
(34' 2")
3132 mm
(10' 3")
8657 mm
(28' 5")
4104 mm
(13' 5")
541 mm
(21")
970 mm
(3' 2")
3146 mm
(10' 3")
3375 mm
(11' 1")
16 834G Wheel Dozer specifications
Blade Overall Digging Ground Maximum Total Operating
Type Capacity Width Height Depth Clearance Tilt Weight Weight
Straight
Blade 7.90 m3 5074 mm 1461 mm 557 mm 1279 mm 1270 mm 3196 kg 47 106 kg
10.33 yd3 199.8 in 57.5 in 21.9 in 50.4 in 50.0 in 7,047 lb 103,849 lb
Universal
Blade 11.13 m3 5151 mm 1461 mm 557 mm 1279 mm 1270 mm 4554 kg 48 464 kg
14.56 yd3 202.8 in 57.5 in 21.9 in 50.4 in 50.0 in 10,042 lb 106,844 lb
Coal Blade 22.2 m3 5677 mm 1956 mm 465 mm 1178 mm 1482 mm 4290 kg 48 195 kg
29.0 yd3 223.5 in 77.0 in 18.3 in 46.4 in 58.3 in 9450 lb 106,252 lb
Blade Specifications
Dimensions
All dimensions are approximate.
17. 17834G Wheel Dozer specifications
Standard Equipment
Standard equipment may vary. Consult a Caterpillar dealer for specifications.
Power Train
Brakes, full hydraulic, ADEM™ III, enclosed, wet multiple
disc service brakes
Engine, Cat 3456 EUI direct injected diesel
Full priming pump
Muffler, under hood
Parking brake
Precleaner, engine air intake
Radiator, Advanced Modular Cooling System (AMOCS)
Rimpull control
Separated cooling system
Starting aid (ether)
Throttle lock
Torque Converter, Impeller Clutch with lock-up
control system
Transmission, planetary, auto-shift (4F/3R)
Other Standard Equipment
Cab tilt support
Demand fan
Doors, service access (locking)
Engine, crankcase, 600-hour interval with CH-4 oil
Hitch, drawbar with pin
Oil sampling valves
Stairway, left side (rear access)
Vandalism protection and caplocks
Venturi stack
Bulldozer
Bulldozer is not included in the standard equipment
Hydraulics
Hydraulic oil cooler
Case drain filtration
Tires, Rims and Wheels
A tire must be selected from the mandatory attachments
section and base machine price includes a tire allowance
Antifreeze
Premixed 50 percent concentration of Extended Life
Coolant with freeze protection to -34° C (-29° F)
Electrical
Alarm, back-up
Alternator (100-amp)
Batteries, maintenance-free
Deutsch terminal connectors
Diagnostic connector, starting and charging systems
Electrical converter (12-volt)
Electrical system (24-volt)
Lighting system, halogen (front and rear)
Starter, electric (heavy-duty)
Starting receptacle for emergency start
Operator Environment
Air conditioner
Cab, sound suppressed pressurized
Internal four-post Rollover Protection Structure
(ROPS)/Falling Object Protection Structure (FOPS)
Radio (entertainment) ready includes antenna, speakers,
converter (12-volt, 5-amp)
Cigar lighter and ashtray
Coat hook
Heater and defroster
Horn, electric
Hydraulic controls (floor mounted)
Light, dome (cab)
Lunchbox and beverage holders
Monitoring system (Caterpillar Monitoring System [EMS-III])
Action alert system, three-category
Instrumentation, gauges:
Engine coolant temperature
Fuel level
Hydraulic oil temperature
Torque converter temperature
Instrumentation, warning indicators:
Axle oil temperature
Brake oil pressure
Coolant flow status
Electrical system, low voltage
Engine oil pressure
Engine overspeed
Hydraulic filter status
Parking brake status
Steering oil pressure
Transmission filter status
Mirror, rearview (externally mounted)
Seat, Cat Comfort (cloth) air suspension
Seatbelt, retractable, 76 mm (3 in) wide
STIC control system with steering lock
Tinted glass
Transmission gear (indicator)
Wet-arm wipers/washers (front and rear)
Intermittent front wiper
18. ELECTRICAL
Lighting, standard 0 kg 0 lb
Lights, directional 2 kg 5 lb
POWER TRAIN
Fuel Systems
Fuel arrangement 0 kg 0 lb
Fuel, fast fill 4 kg 8 lb
Heater, fuel 4 kg 8 lb
Fuel, fast fill with heater 7 kg 16 lb
Engines
Engine, standard 0 kg 0 lb
Engine, Jake Brake 4 kg 8 lb
ACCESS STAIRS AND FENDER ARRANGEMENTS
Stairway, standard 0 kg 0 lb
Stairway and fenders 312 kg 687 lb
SOUND SUPPRESSION ARRANGEMENTS
No suppression arrangement 0 kg 0 lb
Sound suppression arrangement 93 kg 206 lb
HYDRAULICS
Steering Systems
Steering, standard 0 kg 0 lb
Steering, secondary 14 kg 30 lb
Filtration Systems
Filtration, standard 0 kg 0 lb
Filtration, case drain 5 kg 12 lb
Mandatory Attachments (select one from each group)
Mandatory and optional equipment may vary. Consult your Caterpillar dealer for specifics.
18 834G Wheel Dozer specifications
ELECTRICAL
Lights, auxiliary package 2 kg 4 lb
GUARDS
Guards, crankcase 53 kg 117 lb
Guards, hydraulic tank 8 kg 18 lb
OPERATOR ENVIRONMENT
Wiper, intermittent rear 9 kg 2 lb
Visor, front 5 kg 10 lb
Mirror, internal (panoramic) 5 kg 11 lb
POWER TRAIN
Differential, No-SPIN, rear 5 kg 11 lb
Cooler, axle oil 183 kg 403 lb
STARTING AIDS
Heater, engine coolant 2 kg 4 lb
Heater, 220-volt 1 kg 3 lb
MISCELLANEOUS ATTACHMENTS
Oil change, high speed 4 kg 8 lb
Precleaner, turbine/trash 14 kg 30 lb
ANTIFREEZE
Coolant, ext life -50°C (-58° F) 0 kg 0 lb
BULLDOZERS
Note: Contact CWTS for coal blade option
Bulldozer AR, no blade 4267 kg 9408 lb
Bulldozer AR, straight blade 7348 kg 16,200 lb
Bulldozer AR, U-blade 9251 kg 20,394 lb
Optional Equipment
Optional equipment may vary. Consult your Caterpillar dealer for specifics.