This document contains technical specifications for two electrically operated ball valves with single phase quarter turn electric actuators. It provides details on the valve specifications, actuator details, motor details, and optional accessories. The valves can be fitted with proportional or on/off actuators for water applications. The actuators are IP67 rated and provide 50Nm of torque from a 110W motor with position feedback accessories optional. An 18 month warranty is included.
This document provides information on the design of pressure vessels. It defines pressure vessels as containers designed to operate above 15 Psi and discusses why proper design is important to prevent failure. The document outlines various codes used for pressure vessel design and stresses that vessels experience from internal pressure, weight, and other loads. It also describes common pressure vessel components like shells, heads, nozzles, and supports, and provides formulas for calculating thicknesses of different vessel components.
This document provides assembly, component, and maintenance details for a floating head heat exchanger. It includes general assembly and cross-sectional views labeling major components like the shell, tube bundle, floating head, and distributor. Step-by-step maintenance procedures are described for activities like removing the bundle, hydrotesting the shell and tube sides, eliminating tube leaks, and final hydrotesting before unit startup. Safety and proper housekeeping during maintenance are emphasized.
The document provides information about air compressor ZR Atlas Copco, including its main parts, technical specifications, systems, maintenance strategy, and a maintenance case study. It introduces the compressor, describing its filter, elements, motor, and controls. Diagrams show the cooling, oil, and air systems. The maintenance strategy outlines inspection levels based on running hours, including tasks like checking for leaks and replacing filters. The case study describes experiences maintaining a similar compressor, such as replacing worn elements, filters, and other parts.
The document provides an overview of an industrial training at Reliance Industries Limited's refinery in Jamnagar, India. It discusses the refining process, including fractional distillation of crude oil in atmospheric and vacuum distillation towers. Key components of an oil refinery are described, such as desalters, heat exchangers, storage tanks, pumps, compressors, and piping. Centrifugal pumps are commonly used and their components and operating characteristics like Net Positive Suction Head are explained. The training helped link the student's classroom knowledge to practical applications in industry.
The document provides an overview of process plant piping system design. It discusses key components of piping systems including pipe, fittings, flanges, gaskets, bolting, valves and supports. It describes design requirements according to the ASME B31.3 code and considerations for material selection such as strength, corrosion resistance, toughness and cost. Examples of stress analysis, flange rating determination and valve selection are also provided.
Pressure vessels are designed to safely operate at specific pressures and temperatures. They consist of a cylindrical shell and elliptical or hemispherical heads and are used in applications like reactors, heat exchangers, and storage tanks. Pressure vessels are categorized based on whether they are fired or unfired. Unfired pressure vessels include tanks for storing gases and liquids and are designed according to codes like IS 2825-1969, which specifies design procedures and allows for different material stresses and corrosion allowances depending on the vessel's class. Key considerations in pressure vessel design include operating conditions, materials, dimensions, openings, and supports.
This document provides information on flange management including piping specifications, flanges, gaskets, and flange bolting. It discusses piping specifications, commonly used materials, pipe sizing standards, flange types, standards, pressure and temperature ratings, specifications, identification, installation guidelines, and gasket types. It emphasizes the importance of following piping specifications and using the correct materials for flanges and gaskets according to the service conditions.
The document discusses inspection of heat exchangers during manufacture. It outlines the key components of a heat exchanger that will be covered, including shells, channels, tube sheets, baffles, tubes, bellows, spacers, and tie rods. Minimum inspection requirements are described for each component, focusing on dimensions, workmanship, materials, and critical points often overlooked. Testing procedures for the completed heat exchanger like hydrotesting and helium leak testing are also summarized.
This document provides information on the design of pressure vessels. It defines pressure vessels as containers designed to operate above 15 Psi and discusses why proper design is important to prevent failure. The document outlines various codes used for pressure vessel design and stresses that vessels experience from internal pressure, weight, and other loads. It also describes common pressure vessel components like shells, heads, nozzles, and supports, and provides formulas for calculating thicknesses of different vessel components.
This document provides assembly, component, and maintenance details for a floating head heat exchanger. It includes general assembly and cross-sectional views labeling major components like the shell, tube bundle, floating head, and distributor. Step-by-step maintenance procedures are described for activities like removing the bundle, hydrotesting the shell and tube sides, eliminating tube leaks, and final hydrotesting before unit startup. Safety and proper housekeeping during maintenance are emphasized.
The document provides information about air compressor ZR Atlas Copco, including its main parts, technical specifications, systems, maintenance strategy, and a maintenance case study. It introduces the compressor, describing its filter, elements, motor, and controls. Diagrams show the cooling, oil, and air systems. The maintenance strategy outlines inspection levels based on running hours, including tasks like checking for leaks and replacing filters. The case study describes experiences maintaining a similar compressor, such as replacing worn elements, filters, and other parts.
The document provides an overview of an industrial training at Reliance Industries Limited's refinery in Jamnagar, India. It discusses the refining process, including fractional distillation of crude oil in atmospheric and vacuum distillation towers. Key components of an oil refinery are described, such as desalters, heat exchangers, storage tanks, pumps, compressors, and piping. Centrifugal pumps are commonly used and their components and operating characteristics like Net Positive Suction Head are explained. The training helped link the student's classroom knowledge to practical applications in industry.
The document provides an overview of process plant piping system design. It discusses key components of piping systems including pipe, fittings, flanges, gaskets, bolting, valves and supports. It describes design requirements according to the ASME B31.3 code and considerations for material selection such as strength, corrosion resistance, toughness and cost. Examples of stress analysis, flange rating determination and valve selection are also provided.
Pressure vessels are designed to safely operate at specific pressures and temperatures. They consist of a cylindrical shell and elliptical or hemispherical heads and are used in applications like reactors, heat exchangers, and storage tanks. Pressure vessels are categorized based on whether they are fired or unfired. Unfired pressure vessels include tanks for storing gases and liquids and are designed according to codes like IS 2825-1969, which specifies design procedures and allows for different material stresses and corrosion allowances depending on the vessel's class. Key considerations in pressure vessel design include operating conditions, materials, dimensions, openings, and supports.
This document provides information on flange management including piping specifications, flanges, gaskets, and flange bolting. It discusses piping specifications, commonly used materials, pipe sizing standards, flange types, standards, pressure and temperature ratings, specifications, identification, installation guidelines, and gasket types. It emphasizes the importance of following piping specifications and using the correct materials for flanges and gaskets according to the service conditions.
The document discusses inspection of heat exchangers during manufacture. It outlines the key components of a heat exchanger that will be covered, including shells, channels, tube sheets, baffles, tubes, bellows, spacers, and tie rods. Minimum inspection requirements are described for each component, focusing on dimensions, workmanship, materials, and critical points often overlooked. Testing procedures for the completed heat exchanger like hydrotesting and helium leak testing are also summarized.
This document provides information on SKF's SONL plummer block housings, which are split pillow block housings designed for oil lubrication. Key details include:
- SONL housings use proven oil lubrication techniques like oil pickup rings and circulating oil systems to provide uniform lubrication to bearings.
- They have a deep reservoir and efficient seals to hold oil and minimize maintenance needs.
- The housings are designed for universal application with features like locating and non-locating bearing positions and options for adapter sleeves or cylindrical bores.
- SONL housings provide a reliable shaft solution for applications requiring oil lubrication like fans, generators, and
This document provides procedures for the fabrication, installation, and erection of piping. It outlines responsibilities for construction management, engineering, quality control, and health and safety. It also describes procedures for receiving and storing materials, pre-fabrication including cutting, beveling and fit-up, welding, testing, and installation of underground and erected piping. Attachments include job safety analyses, work flows, lifting plans, and inspection forms. The goal is to ensure compliance with contractual and health, safety, and environmental requirements for piping work.
The document illustrates different types of pressure vessels including a horizontal drum on saddle supports, a vertical vessel with leg support, a vertical vessel with lug support, a column, and a reactor. Each illustration shows the main components of the vessel including the shell, heads, supports, nozzles, and internal structures like catalyst beds.
This manual covers the basic guidelines and minimum requirements for
periodic inspection of heat exchangers used in petroleum refinery.
Locations to be inspected, inspection tools, frequency of inspection &
testing, locations prone to deterioration and causes, corrosion
mitigation, inspection and testing procedures have been specified in
the manual.
Documentation of observations & history of heat exchangers,
inspection checklist and recommended practices have also been
included.
Heat exchanging equipment is used for heating or cooling a fluid.
Individual heat transfer equipment is named as per its function.
Cooler
A cooler cools the process fluid, using water or air, with no change of
phase.
Chiller
A chiller uses a refrigerant to cool process fluid to a temperature below
that obtainable with water.
Condenser
A condenser condenses a vapour or mixture of vapours using water or
air.
Exchanger
An exchanger performs two functions in that it heats a cold process
fluid by recovering heat from a hot fluid, which it cools. None of the
transferred heat is lost.
An air compressor compresses atmospheric air to produce high-pressure air for uses onboard ships such as starting diesel engines, pneumatic tools, and instrumentation. Air compressors can be classified as positive displacement or dynamic, and include reciprocating, rotary, and centrifugal models. Compressed air is distributed at various pressures depending on its intended use, such as high pressure for starting engines, medium pressure for general service, and low pressure for instrumentation.
The document summarizes ASME Section VIII Division 1 code requirements for material identification, repair of material defects, Charpy impact testing of production test coupons, weld joint categories, radiographic and ultrasonic examination, welding requirements, and acceptance standards for non-destructive examination. Key points include requirements for original material markings, testing procedures that vary based on joint category and position, examination types based on joint size and material thickness, welder identification, pre-welding surface preparation, and imperfection acceptance criteria.
This document outlines the contents of a training course on hot tapping requirements and simulation. The course contains 4 modules: 1) Piping systems, which covers pipes, flanges, fittings, and gaskets; 2) Welding processes, symbols, electrodes, and non-destructive testing; 3) Hot tapping requirements; and 4) Hot tapping simulation. Module 1 provides details on piping materials, sizes, standards, and components. Module 2 describes common welding techniques and introduces welding symbols. Module 3 focuses on hot tapping requirements, while Module 4 involves simulations of hot tapping procedures.
This document summarizes a presentation given by Vaibhav Kumar Arya on vocational training at Bharat Petroleum Corporation Limited in Mumbai. It discusses BPCL's refineries and history. It then focuses on centrifugal pumps, describing their main components and providing a case study on disassembling, cleaning, inspecting and reassembling a specific pump model. The pump was taken apart to replace a leaking mechanical seal and other worn parts.
This document discusses different types of storage tanks used in refineries and chemical plants. It describes atmospheric storage tanks, which operate at approximately atmospheric pressure, including fixed-roof tanks, floating-roof tanks, and fixed-roof tanks with an internal floating roof. Low-temperature and low-pressure storage tanks are also discussed. Standards for storage tank design include API-650 for atmospheric tanks and API-620 for low-pressure tanks. Floating roof tanks are described as minimizing vapor losses by maintaining a small vapor space or eliminating it completely.
This document provides information about heat exchangers, including:
- Heat exchangers transfer energy between fluids at different temperatures through conduction, convection and radiation.
- They have advantages like being economical, having high efficiency and being easy to modify.
- Heat exchangers can be classified by their flow configuration, transfer process, construction and heat transfer mechanism.
- Common types include shell and tube, plate, double pipe, and condensers, evaporators and boilers.
- Maintenance includes hydrotesting to detect leaks and plugging leaking tubes temporarily or permanently.
A pressure vessel is a container designed to hold gases or liquids at a pressure different from ambient pressure. Common materials used include steel, aluminum, and polymers. The manufacturing process involves forming, pressing, spinning, bending, welding, post weld heat treatment, assembly, and painting. Forming changes the size or shape through application of force using hot, warm, or cold processes. Welding permanently joins materials by melting them. Post weld heat treatment improves the properties of the weldment.
Este documento proporciona instrucciones para la instalación, operación y mantenimiento de bombas centrífugas verticales (VTP). Incluye información sobre tipos de bombas VTP, seguridad, transporte, almacenamiento, descripción de las bombas, instalación, puesta en marcha, operación, mantenimiento y solución de problemas. El documento contiene planos e ilustraciones de las bombas VTP.
El documento resume los principales puntos del código API 510 para la inspección de recipientes a presión. El código establece estándares para determinar la integridad mecánica y reparaciones efectivas de recipientes a presión. Cubre temas como organización de inspección, prácticas de inspección, evaluación de datos e intervalos de inspección. También describe exclusiones y aplicaciones específicas del código para recipientes de exploración y producción.
1. The document discusses industrial fans and draft systems for combustion. It describes natural draft produced by chimneys and mechanical draft produced using fans.
2. The main types of mechanical draft systems are induced draft, forced draft, and balanced draft. Induced draft uses a fan to draw exhaust gases into the chimney. Forced draft uses a fan to push air into the furnace.
3. The document provides details on fan construction, types of fans including axial and centrifugal, installation procedures, and maintenance best practices like lubrication and vibration checking.
The document describes the central cooling water system used on ships. It has two interconnected freshwater circuits called the high temperature (HT) and low temperature (LT) circuits. The HT circuit cools the main and auxiliary engines while the LT circuit cools other machinery. Temperature is controlled through the use of 3-way valves that mix water from the LT and HT circuits. A seawater circuit with heat exchangers and pumps provides cooling to the freshwater circuits. The central cooling system provides both heating and cooling to ship systems in a simplified configuration compared to individual cooling arrangements.
1) Pressure vessels are containers that store fluids under pressure. They are designed to withstand internal pressure loads.
2) Key components of pressure vessel design include the shell, end closures, nozzles, flanged joints, and vessel supports. The shell must be designed to withstand internal pressure as well as combined loading.
3) End closures can be flat heads or formed heads like hemispherical, torispherical, or elliptical heads. Vertical vessels are supported by brackets or skirts and horizontal vessels use saddles.
This document provides information about steam generating units and boiler systems. It defines steam and describes the main uses of steam. It then discusses what a boiler is and how it works to generate steam. The document classifies boilers based on their tube configuration, furnace position, circulation method, and pressure. It proceeds to describe different types of boilers in detail, including fire tube boilers, water tube boilers, packaged boilers, fluidized bed boilers, stoker fired boilers, pulverized fuel boilers, waste heat boilers, and nuclear steam generating systems. It also discusses boiler drum components and functions.
This document summarizes the design requirements for steel anchors embedded in concrete according to ACI 349.2R97 Appendix B. The code aims to ensure a ductile failure mode where the reinforcement yields before the concrete fails. For anchors designed for direct loading, the concrete pullout strength must exceed the steel tensile strength. The document then provides an example calculation to check if the anchor steel area, head bearing capacity, and embedment length are sufficient to resist the required tensile force based on the code requirements.
Valve maintenance is important to ensure worker safety, smooth operation, and that the valve is functioning properly. Key maintenance items include changing the gasket, changing the gland packing at least every two years or as needed, and lapping the disc and seat to ensure a tight seal when the valve is closed.
This document provides specifications for an electrically operated 2-way ball valve fitted with a single phase quarter turn electric actuator. Some key details include:
- The ball valve is 50mm in size with a 40mm port, carbon steel body, SS316 ball and teflon seating. It has a maximum pressure rating of 10 bar.
- The actuator is a Sdtork brand single phase quarter turn model SD-1000-05 with IP65 protection. It has limit switches, local indicator, and is rated for 230V AC power.
- Optional accessories include a feedback potentiometer, additional limit switches, two-wire transmitter, remote position indicator, servo controller, and local push button station.
This document provides specifications for an electrically operated 2-way ball valve fitted with a single phase quarter turn electric actuator. Some key details include:
- The ball valve is 50mm in size with a 40mm port, carbon steel body, SS316 ball and teflon seating. It has a maximum pressure rating of 10 bar.
- The actuator is a Sdtork brand single phase quarter turn model with 230V AC power supply. It has position limit switches and an IP65 protection rating.
- The actuator has a reversible single phase synchronous stall duty motor rated for 230V AC power.
- Optional accessories include a feedback potentiometer, additional limit switches, two-wire transmitter, remote
This document provides information on SKF's SONL plummer block housings, which are split pillow block housings designed for oil lubrication. Key details include:
- SONL housings use proven oil lubrication techniques like oil pickup rings and circulating oil systems to provide uniform lubrication to bearings.
- They have a deep reservoir and efficient seals to hold oil and minimize maintenance needs.
- The housings are designed for universal application with features like locating and non-locating bearing positions and options for adapter sleeves or cylindrical bores.
- SONL housings provide a reliable shaft solution for applications requiring oil lubrication like fans, generators, and
This document provides procedures for the fabrication, installation, and erection of piping. It outlines responsibilities for construction management, engineering, quality control, and health and safety. It also describes procedures for receiving and storing materials, pre-fabrication including cutting, beveling and fit-up, welding, testing, and installation of underground and erected piping. Attachments include job safety analyses, work flows, lifting plans, and inspection forms. The goal is to ensure compliance with contractual and health, safety, and environmental requirements for piping work.
The document illustrates different types of pressure vessels including a horizontal drum on saddle supports, a vertical vessel with leg support, a vertical vessel with lug support, a column, and a reactor. Each illustration shows the main components of the vessel including the shell, heads, supports, nozzles, and internal structures like catalyst beds.
This manual covers the basic guidelines and minimum requirements for
periodic inspection of heat exchangers used in petroleum refinery.
Locations to be inspected, inspection tools, frequency of inspection &
testing, locations prone to deterioration and causes, corrosion
mitigation, inspection and testing procedures have been specified in
the manual.
Documentation of observations & history of heat exchangers,
inspection checklist and recommended practices have also been
included.
Heat exchanging equipment is used for heating or cooling a fluid.
Individual heat transfer equipment is named as per its function.
Cooler
A cooler cools the process fluid, using water or air, with no change of
phase.
Chiller
A chiller uses a refrigerant to cool process fluid to a temperature below
that obtainable with water.
Condenser
A condenser condenses a vapour or mixture of vapours using water or
air.
Exchanger
An exchanger performs two functions in that it heats a cold process
fluid by recovering heat from a hot fluid, which it cools. None of the
transferred heat is lost.
An air compressor compresses atmospheric air to produce high-pressure air for uses onboard ships such as starting diesel engines, pneumatic tools, and instrumentation. Air compressors can be classified as positive displacement or dynamic, and include reciprocating, rotary, and centrifugal models. Compressed air is distributed at various pressures depending on its intended use, such as high pressure for starting engines, medium pressure for general service, and low pressure for instrumentation.
The document summarizes ASME Section VIII Division 1 code requirements for material identification, repair of material defects, Charpy impact testing of production test coupons, weld joint categories, radiographic and ultrasonic examination, welding requirements, and acceptance standards for non-destructive examination. Key points include requirements for original material markings, testing procedures that vary based on joint category and position, examination types based on joint size and material thickness, welder identification, pre-welding surface preparation, and imperfection acceptance criteria.
This document outlines the contents of a training course on hot tapping requirements and simulation. The course contains 4 modules: 1) Piping systems, which covers pipes, flanges, fittings, and gaskets; 2) Welding processes, symbols, electrodes, and non-destructive testing; 3) Hot tapping requirements; and 4) Hot tapping simulation. Module 1 provides details on piping materials, sizes, standards, and components. Module 2 describes common welding techniques and introduces welding symbols. Module 3 focuses on hot tapping requirements, while Module 4 involves simulations of hot tapping procedures.
This document summarizes a presentation given by Vaibhav Kumar Arya on vocational training at Bharat Petroleum Corporation Limited in Mumbai. It discusses BPCL's refineries and history. It then focuses on centrifugal pumps, describing their main components and providing a case study on disassembling, cleaning, inspecting and reassembling a specific pump model. The pump was taken apart to replace a leaking mechanical seal and other worn parts.
This document discusses different types of storage tanks used in refineries and chemical plants. It describes atmospheric storage tanks, which operate at approximately atmospheric pressure, including fixed-roof tanks, floating-roof tanks, and fixed-roof tanks with an internal floating roof. Low-temperature and low-pressure storage tanks are also discussed. Standards for storage tank design include API-650 for atmospheric tanks and API-620 for low-pressure tanks. Floating roof tanks are described as minimizing vapor losses by maintaining a small vapor space or eliminating it completely.
This document provides information about heat exchangers, including:
- Heat exchangers transfer energy between fluids at different temperatures through conduction, convection and radiation.
- They have advantages like being economical, having high efficiency and being easy to modify.
- Heat exchangers can be classified by their flow configuration, transfer process, construction and heat transfer mechanism.
- Common types include shell and tube, plate, double pipe, and condensers, evaporators and boilers.
- Maintenance includes hydrotesting to detect leaks and plugging leaking tubes temporarily or permanently.
A pressure vessel is a container designed to hold gases or liquids at a pressure different from ambient pressure. Common materials used include steel, aluminum, and polymers. The manufacturing process involves forming, pressing, spinning, bending, welding, post weld heat treatment, assembly, and painting. Forming changes the size or shape through application of force using hot, warm, or cold processes. Welding permanently joins materials by melting them. Post weld heat treatment improves the properties of the weldment.
Este documento proporciona instrucciones para la instalación, operación y mantenimiento de bombas centrífugas verticales (VTP). Incluye información sobre tipos de bombas VTP, seguridad, transporte, almacenamiento, descripción de las bombas, instalación, puesta en marcha, operación, mantenimiento y solución de problemas. El documento contiene planos e ilustraciones de las bombas VTP.
El documento resume los principales puntos del código API 510 para la inspección de recipientes a presión. El código establece estándares para determinar la integridad mecánica y reparaciones efectivas de recipientes a presión. Cubre temas como organización de inspección, prácticas de inspección, evaluación de datos e intervalos de inspección. También describe exclusiones y aplicaciones específicas del código para recipientes de exploración y producción.
1. The document discusses industrial fans and draft systems for combustion. It describes natural draft produced by chimneys and mechanical draft produced using fans.
2. The main types of mechanical draft systems are induced draft, forced draft, and balanced draft. Induced draft uses a fan to draw exhaust gases into the chimney. Forced draft uses a fan to push air into the furnace.
3. The document provides details on fan construction, types of fans including axial and centrifugal, installation procedures, and maintenance best practices like lubrication and vibration checking.
The document describes the central cooling water system used on ships. It has two interconnected freshwater circuits called the high temperature (HT) and low temperature (LT) circuits. The HT circuit cools the main and auxiliary engines while the LT circuit cools other machinery. Temperature is controlled through the use of 3-way valves that mix water from the LT and HT circuits. A seawater circuit with heat exchangers and pumps provides cooling to the freshwater circuits. The central cooling system provides both heating and cooling to ship systems in a simplified configuration compared to individual cooling arrangements.
1) Pressure vessels are containers that store fluids under pressure. They are designed to withstand internal pressure loads.
2) Key components of pressure vessel design include the shell, end closures, nozzles, flanged joints, and vessel supports. The shell must be designed to withstand internal pressure as well as combined loading.
3) End closures can be flat heads or formed heads like hemispherical, torispherical, or elliptical heads. Vertical vessels are supported by brackets or skirts and horizontal vessels use saddles.
This document provides information about steam generating units and boiler systems. It defines steam and describes the main uses of steam. It then discusses what a boiler is and how it works to generate steam. The document classifies boilers based on their tube configuration, furnace position, circulation method, and pressure. It proceeds to describe different types of boilers in detail, including fire tube boilers, water tube boilers, packaged boilers, fluidized bed boilers, stoker fired boilers, pulverized fuel boilers, waste heat boilers, and nuclear steam generating systems. It also discusses boiler drum components and functions.
This document summarizes the design requirements for steel anchors embedded in concrete according to ACI 349.2R97 Appendix B. The code aims to ensure a ductile failure mode where the reinforcement yields before the concrete fails. For anchors designed for direct loading, the concrete pullout strength must exceed the steel tensile strength. The document then provides an example calculation to check if the anchor steel area, head bearing capacity, and embedment length are sufficient to resist the required tensile force based on the code requirements.
Valve maintenance is important to ensure worker safety, smooth operation, and that the valve is functioning properly. Key maintenance items include changing the gasket, changing the gland packing at least every two years or as needed, and lapping the disc and seat to ensure a tight seal when the valve is closed.
This document provides specifications for an electrically operated 2-way ball valve fitted with a single phase quarter turn electric actuator. Some key details include:
- The ball valve is 50mm in size with a 40mm port, carbon steel body, SS316 ball and teflon seating. It has a maximum pressure rating of 10 bar.
- The actuator is a Sdtork brand single phase quarter turn model SD-1000-05 with IP65 protection. It has limit switches, local indicator, and is rated for 230V AC power.
- Optional accessories include a feedback potentiometer, additional limit switches, two-wire transmitter, remote position indicator, servo controller, and local push button station.
This document provides specifications for an electrically operated 2-way ball valve fitted with a single phase quarter turn electric actuator. Some key details include:
- The ball valve is 50mm in size with a 40mm port, carbon steel body, SS316 ball and teflon seating. It has a maximum pressure rating of 10 bar.
- The actuator is a Sdtork brand single phase quarter turn model with 230V AC power supply. It has position limit switches and an IP65 protection rating.
- The actuator has a reversible single phase synchronous stall duty motor rated for 230V AC power.
- Optional accessories include a feedback potentiometer, additional limit switches, two-wire transmitter, remote
This document provides specifications for a 2-way ball valve fitted with a single phase quarter turn electric actuator. Some key details include:
- The ball valve is 50mm in size with a 40mm port, BSP screwed end connection, carbon steel body, SS316 ball and Teflon seating material for water applications.
- The actuator is a Sdtork make single phase quarter turn electric actuator with a 230V AC supply voltage. It has two limit switches and a local indicator.
- Motor details include a reversible single phase synchronous stall duty motor with a 230V +/- 10% AC supply and S2-10 minute duty rating.
- Optional accessories are also listed but not provided, such
This document provides specifications for a 2-way ball valve fitted with a single phase quarter turn electric actuator. Some key details include:
- The ball valve is 50mm in size with a 40mm port, BSP screwed end connection, carbon steel body, SS316 ball and Teflon seating material for water applications.
- The actuator is a Sdtork make single phase quarter turn electric actuator with a 230V AC supply voltage. It has two limit switches and a local indicator.
- Motor details include a reversible single phase synchronous stall duty motor with a 230V +/- 10% AC supply and S2-10 minute duty rating.
- Optional accessories are also listed but not provided, such
This document provides specifications for a 2-way plastic ball valve fitted with a single phase quarter turn electric actuator. The valve is 50mm in size with PVC body and ball and teflon seating. It operates at 10 bar pressure and ambient temperature. The actuator is a Sdtork SD-1000-05 model with IP65 protection. Optional accessories include a feedback potentiometer, additional limit switches, a two-wire transmitter, remote position indicator, servo controller, interface card and local push button station. The valve and actuator assembly comes with an 18-month warranty and inspection can be done at the supplier's works.
This document provides specifications for a 2-way plastic ball valve fitted with a single phase quarter turn electric actuator. The valve is 50mm in size with BSP screwed ends, a PVC body and ball, teflon seating, and is rated for a maximum pressure of 10 bars and ambient temperature. The actuator model is SD-1000-05 and provides on/off operation from a 230V AC power supply. Inspection will be done by the customer at the manufacturer's works and the unit comes with a 18 month warranty.
This document provides specifications for a 2-way plastic ball valve fitted with a single phase quarter turn electric actuator. The valve is 50mm in size with BSP screwed ends, a PVC body and ball, teflon seating, and is rated for a maximum pressure of 10 bars and ambient temperature. The actuator model is SD-1000-05 and provides on/off operation from a 230V AC power supply. Inspection will be done by the customer at the manufacturer's works and the unit comes with a 18 month warranty.
This document provides specifications for a 2-way plastic ball valve fitted with a single phase quarter turn electric actuator. The valve is 50mm in size with BSP screwed ends, a PVC body and ball, teflon seating, and is rated for a maximum pressure of 10 bars and ambient temperature. The actuator model is SD-1000-05 and provides on/off operation from a 230V AC power supply. Inspection will be done by the customer at the manufacturer's works and the unit comes with a 18 month warranty.
This document provides specifications for a 2-way plastic ball valve fitted with a single phase quarter turn electric actuator. The valve is 50mm in size with BSP screwed ends, a PVC body and ball, teflon seating, and is rated for a maximum pressure of 10 bars and ambient temperature. The actuator model is SD-1000-05 and provides on/off operation from a 230V AC power supply. Inspection will be done by the customer at the manufacturer's works and the unit comes with a 18 month warranty.
This document provides specifications for a 2-way butterfly valve with an electrically operated actuator.
The valve is 200mm in size, has a cast iron body and SG iron disc, and is rated for 16kg/cm2 pressure and ambient temperature water service. It has a wafer connection and nitrile seat.
The electrical actuator is a Sdtork brand, three-phase, reversible, stay-put type with IP67 protection. It provides a 0-90 degree quarter turn on 415V power. Accessories include local position indication, manual override, and torque/travel limit switches.
Testing will be conducted at the supplier's works and an 18-month warranty is provided.
This document provides specifications for a 2-way butterfly valve with an electrically operated actuator.
The valve is 200mm in size, has a cast iron body and SG iron disc, and is rated for 10kg/cm2 pressure and ambient temperature water service. It has a PN16 construction and operates through 90 degrees rotation.
The electrical actuator is a Sdtork brand model SD-4000-20-E with IP67 protection. It is a 3-phase 415V AC unit with a quarter turn output, local position indicator, and manual override handwheel.
Testing, manuals, and an 18-month warranty are included in the scope of supply. Optional accessories like feedback pots, limit switches
This document provides specifications for a 200mm, cast iron butterfly valve fitted with an electrical actuator. The valve has a wafer connection, PN16 construction, and is used for water applications. The Sdtork electrical actuator is reversible and splash proof, with controls for local position indication, manual override, travel and torque limit switches, and an IP67 enclosure. The actuator provides quarter turn motion in 12 seconds and is powered by a 415V, 3-phase motor. Optional accessories include feedback and limit switches, a two-wire transmitter, and remote position indication.
The document provides specifications for a 1258/200/WAF/PVC/PVC/E/PN16/SUDE/PUNE electrically operated plastic butterfly valve. The key details are:
1. The valve is 200mm in size, with wafer/flangeless ends made of PVC. It has a PVC disc and EPDM seating material.
2. It comes fitted with a Sdtork make three phase electrical reversible actuator with local position indicator, IP67 protection, and manual override handwheel.
3. The actuator is model SD-4000-20-E with torque and travel limit switches, and operates over 0-90 degrees in less than 20 seconds
The document provides specifications for a 1258/200/WAF/PVC/PVC/E/PN16/SUDE electrically operated plastic butterfly valve. The key details are:
1. It is a 2-way plastic butterfly valve with a 200mm wafer connection made of PVC suitable for 10kg/cm2 pressure.
2. It is fitted with a Sdtork make 415V 3-phase electrical actuator with local position indicator, handwheel, IP67 protection, and 18 months warranty.
3. The actuator provides 0-90 degree rotation in less than 20 seconds and has manual override, travel limit switches, and torque limit switches.
This document provides technical specifications for a single phase quarter turn electrical actuator made by sdtork. It details the actuator model, output motion and torque, manual hand wheel, travel limit switches, local indicator, IP protection class, mounting, and weight. Motor details include type, supply, duty, and insulation class. Optional accessories that may be provided include a feedback potentiometer, additional limit switches, two-wire transmitter, remote position indicator, servo controller, interface card, control panel, and local push button station. General points note the scope of supply, inspection terms, manuals, warranty, and packing.
This document provides specifications for a 1258/200/WAF/PVC/PVC/E/PN16/PROP/SD-4000-20-E/2LS/POT/CPT200/WCP plastic butterfly valve with an integrated Sdtork make 3-phase electrical actuator. The valve is 200mm with a PVC body and disc, an EPDM seal, and is rated for 10kg/cm2 pressure. The actuator is a Sdtork SD-4000-20-E model with IP67 protection, local position indicator, and limit switches. Motor specifications and additional available accessories are also listed.
This document provides specifications for two electrically operated globe valves. The first is a larger 200mm valve fitted with a 3 phase linear electrical actuator. The second is a smaller 50mm valve fitted with a single phase linear electric actuator. Both provide details on valve and actuator specifications including size, material, pressure and temperature ratings, motor details, accessories, and warranty information.
This document provides specifications for an electrically operated butterfly valve with a Sdtork make three phase electrical actuator. Some key details include:
- The valve is 200mm in size with a cast iron body and SG iron disc for water applications up to 10kg/cm2 pressure.
- The actuator is a Sdtork SD-4000-20-E model with IP67 classification, local position indicator, and handwheel for manual operation. It operates on 415V 3 phase power.
- Accessories include a feedback potentiometer, additional limit switches, two-wire transmitter, remote position indicator, and servo controller or interface card options.
This document provides specifications for an electrically operated butterfly valve with an integrated actuator. It includes details on the butterfly valve such as its size, materials, pressure rating, and temperature range. It also provides extensive details on the integrated electric actuator, including its model, torque rating, controls, indicators, enclosure protection, and accessories. The actuator is powered by a 415V 3-phase motor and includes options for controls and feedback such as limit switches, transmitters, and position indicators.
This document provides technical specifications for a motorised 3-way circular diverter damper with a 3-phase electrical actuator. It includes details on the damper size and materials, actuator model and torque output, motor specifications, and optional accessories. The system will be used for on/off control of gas flow at temperatures up to 250 degrees C and pressures of 500mmWC.
The document discusses SDTORK's 1000 Series single phase quarter turn electrical actuators. The 1000 Series actuators are designed for remote control of ball valves, butterfly valves, dampers and other quarter turn applications up to 600 Nm of torque. The actuators are compact and lightweight with an IP65 enclosure. They provide reliable quarter turn operation, adjustable mechanical stops, feedback and position indication. SDTORK offers these actuators for automated control of valves and dampers.
The document discusses the benefits of exercise for mental health. Regular physical activity can help reduce anxiety and depression and improve mood and cognitive function. Exercise causes chemical changes in the brain that may help protect against mental illness and improve symptoms for those who already suffer from conditions like anxiety and depression.
1900 series damper with electrical and pneumatic actuatorChaitannya Mahatme
The document discusses the benefits of exercise for mental health. Regular physical activity can help reduce anxiety and depression and improve mood and cognitive function. Exercise causes chemical changes in the brain that may help protect against mental illness and improve symptoms.
The document discusses the benefits of exercise for mental health. Regular physical activity can help reduce anxiety and depression and improve mood and cognitive function. Exercise causes chemical changes in the brain that may help protect against mental illness and improve symptoms for those who already suffer from conditions like depression and anxiety.
The document discusses the benefits of exercise for mental health. Regular physical activity can help reduce anxiety and depression and improve mood and cognitive function. Exercise causes chemical changes in the brain that may help protect against mental illness and improve symptoms for those who already suffer from conditions like anxiety and depression.
The document discusses the benefits of exercise for mental health. Regular physical activity can help reduce anxiety and depression and improve mood and cognitive functioning. Exercise causes chemical changes in the brain that may help protect against mental illness and improve symptoms.
GraphRAG for Life Science to increase LLM accuracyTomaz Bratanic
GraphRAG for life science domain, where you retriever information from biomedical knowledge graphs using LLMs to increase the accuracy and performance of generated answers
Essentials of Automations: The Art of Triggers and Actions in FMESafe Software
In this second installment of our Essentials of Automations webinar series, we’ll explore the landscape of triggers and actions, guiding you through the nuances of authoring and adapting workspaces for seamless automations. Gain an understanding of the full spectrum of triggers and actions available in FME, empowering you to enhance your workspaces for efficient automation.
We’ll kick things off by showcasing the most commonly used event-based triggers, introducing you to various automation workflows like manual triggers, schedules, directory watchers, and more. Plus, see how these elements play out in real scenarios.
Whether you’re tweaking your current setup or building from the ground up, this session will arm you with the tools and insights needed to transform your FME usage into a powerhouse of productivity. Join us to discover effective strategies that simplify complex processes, enhancing your productivity and transforming your data management practices with FME. Let’s turn complexity into clarity and make your workspaces work wonders!
Sudheer Mechineni, Head of Application Frameworks, Standard Chartered Bank
Discover how Standard Chartered Bank harnessed the power of Neo4j to transform complex data access challenges into a dynamic, scalable graph database solution. This keynote will cover their journey from initial adoption to deploying a fully automated, enterprise-grade causal cluster, highlighting key strategies for modelling organisational changes and ensuring robust disaster recovery. Learn how these innovations have not only enhanced Standard Chartered Bank’s data infrastructure but also positioned them as pioneers in the banking sector’s adoption of graph technology.
Maruthi Prithivirajan, Head of ASEAN & IN Solution Architecture, Neo4j
Get an inside look at the latest Neo4j innovations that enable relationship-driven intelligence at scale. Learn more about the newest cloud integrations and product enhancements that make Neo4j an essential choice for developers building apps with interconnected data and generative AI.
Let's Integrate MuleSoft RPA, COMPOSER, APM with AWS IDP along with Slackshyamraj55
Discover the seamless integration of RPA (Robotic Process Automation), COMPOSER, and APM with AWS IDP enhanced with Slack notifications. Explore how these technologies converge to streamline workflows, optimize performance, and ensure secure access, all while leveraging the power of AWS IDP and real-time communication via Slack notifications.
Unlock the Future of Search with MongoDB Atlas_ Vector Search Unleashed.pdfMalak Abu Hammad
Discover how MongoDB Atlas and vector search technology can revolutionize your application's search capabilities. This comprehensive presentation covers:
* What is Vector Search?
* Importance and benefits of vector search
* Practical use cases across various industries
* Step-by-step implementation guide
* Live demos with code snippets
* Enhancing LLM capabilities with vector search
* Best practices and optimization strategies
Perfect for developers, AI enthusiasts, and tech leaders. Learn how to leverage MongoDB Atlas to deliver highly relevant, context-aware search results, transforming your data retrieval process. Stay ahead in tech innovation and maximize the potential of your applications.
#MongoDB #VectorSearch #AI #SemanticSearch #TechInnovation #DataScience #LLM #MachineLearning #SearchTechnology
HCL Notes und Domino Lizenzkostenreduzierung in der Welt von DLAUpanagenda
Webinar Recording: https://www.panagenda.com/webinars/hcl-notes-und-domino-lizenzkostenreduzierung-in-der-welt-von-dlau/
DLAU und die Lizenzen nach dem CCB- und CCX-Modell sind für viele in der HCL-Community seit letztem Jahr ein heißes Thema. Als Notes- oder Domino-Kunde haben Sie vielleicht mit unerwartet hohen Benutzerzahlen und Lizenzgebühren zu kämpfen. Sie fragen sich vielleicht, wie diese neue Art der Lizenzierung funktioniert und welchen Nutzen sie Ihnen bringt. Vor allem wollen Sie sicherlich Ihr Budget einhalten und Kosten sparen, wo immer möglich. Das verstehen wir und wir möchten Ihnen dabei helfen!
Wir erklären Ihnen, wie Sie häufige Konfigurationsprobleme lösen können, die dazu führen können, dass mehr Benutzer gezählt werden als nötig, und wie Sie überflüssige oder ungenutzte Konten identifizieren und entfernen können, um Geld zu sparen. Es gibt auch einige Ansätze, die zu unnötigen Ausgaben führen können, z. B. wenn ein Personendokument anstelle eines Mail-Ins für geteilte Mailboxen verwendet wird. Wir zeigen Ihnen solche Fälle und deren Lösungen. Und natürlich erklären wir Ihnen das neue Lizenzmodell.
Nehmen Sie an diesem Webinar teil, bei dem HCL-Ambassador Marc Thomas und Gastredner Franz Walder Ihnen diese neue Welt näherbringen. Es vermittelt Ihnen die Tools und das Know-how, um den Überblick zu bewahren. Sie werden in der Lage sein, Ihre Kosten durch eine optimierte Domino-Konfiguration zu reduzieren und auch in Zukunft gering zu halten.
Diese Themen werden behandelt
- Reduzierung der Lizenzkosten durch Auffinden und Beheben von Fehlkonfigurationen und überflüssigen Konten
- Wie funktionieren CCB- und CCX-Lizenzen wirklich?
- Verstehen des DLAU-Tools und wie man es am besten nutzt
- Tipps für häufige Problembereiche, wie z. B. Team-Postfächer, Funktions-/Testbenutzer usw.
- Praxisbeispiele und Best Practices zum sofortigen Umsetzen
In the rapidly evolving landscape of technologies, XML continues to play a vital role in structuring, storing, and transporting data across diverse systems. The recent advancements in artificial intelligence (AI) present new methodologies for enhancing XML development workflows, introducing efficiency, automation, and intelligent capabilities. This presentation will outline the scope and perspective of utilizing AI in XML development. The potential benefits and the possible pitfalls will be highlighted, providing a balanced view of the subject.
We will explore the capabilities of AI in understanding XML markup languages and autonomously creating structured XML content. Additionally, we will examine the capacity of AI to enrich plain text with appropriate XML markup. Practical examples and methodological guidelines will be provided to elucidate how AI can be effectively prompted to interpret and generate accurate XML markup.
Further emphasis will be placed on the role of AI in developing XSLT, or schemas such as XSD and Schematron. We will address the techniques and strategies adopted to create prompts for generating code, explaining code, or refactoring the code, and the results achieved.
The discussion will extend to how AI can be used to transform XML content. In particular, the focus will be on the use of AI XPath extension functions in XSLT, Schematron, Schematron Quick Fixes, or for XML content refactoring.
The presentation aims to deliver a comprehensive overview of AI usage in XML development, providing attendees with the necessary knowledge to make informed decisions. Whether you’re at the early stages of adopting AI or considering integrating it in advanced XML development, this presentation will cover all levels of expertise.
By highlighting the potential advantages and challenges of integrating AI with XML development tools and languages, the presentation seeks to inspire thoughtful conversation around the future of XML development. We’ll not only delve into the technical aspects of AI-powered XML development but also discuss practical implications and possible future directions.
How to Get CNIC Information System with Paksim Ga.pptxdanishmna97
Pakdata Cf is a groundbreaking system designed to streamline and facilitate access to CNIC information. This innovative platform leverages advanced technology to provide users with efficient and secure access to their CNIC details.
“An Outlook of the Ongoing and Future Relationship between Blockchain Technologies and Process-aware Information Systems.” Invited talk at the joint workshop on Blockchain for Information Systems (BC4IS) and Blockchain for Trusted Data Sharing (B4TDS), co-located with with the 36th International Conference on Advanced Information Systems Engineering (CAiSE), 3 June 2024, Limassol, Cyprus.
Full-RAG: A modern architecture for hyper-personalizationZilliz
Mike Del Balso, CEO & Co-Founder at Tecton, presents "Full RAG," a novel approach to AI recommendation systems, aiming to push beyond the limitations of traditional models through a deep integration of contextual insights and real-time data, leveraging the Retrieval-Augmented Generation architecture. This talk will outline Full RAG's potential to significantly enhance personalization, address engineering challenges such as data management and model training, and introduce data enrichment with reranking as a key solution. Attendees will gain crucial insights into the importance of hyperpersonalization in AI, the capabilities of Full RAG for advanced personalization, and strategies for managing complex data integrations for deploying cutting-edge AI solutions.
Driving Business Innovation: Latest Generative AI Advancements & Success StorySafe Software
Are you ready to revolutionize how you handle data? Join us for a webinar where we’ll bring you up to speed with the latest advancements in Generative AI technology and discover how leveraging FME with tools from giants like Google Gemini, Amazon, and Microsoft OpenAI can supercharge your workflow efficiency.
During the hour, we’ll take you through:
Guest Speaker Segment with Hannah Barrington: Dive into the world of dynamic real estate marketing with Hannah, the Marketing Manager at Workspace Group. Hear firsthand how their team generates engaging descriptions for thousands of office units by integrating diverse data sources—from PDF floorplans to web pages—using FME transformers, like OpenAIVisionConnector and AnthropicVisionConnector. This use case will show you how GenAI can streamline content creation for marketing across the board.
Ollama Use Case: Learn how Scenario Specialist Dmitri Bagh has utilized Ollama within FME to input data, create custom models, and enhance security protocols. This segment will include demos to illustrate the full capabilities of FME in AI-driven processes.
Custom AI Models: Discover how to leverage FME to build personalized AI models using your data. Whether it’s populating a model with local data for added security or integrating public AI tools, find out how FME facilitates a versatile and secure approach to AI.
We’ll wrap up with a live Q&A session where you can engage with our experts on your specific use cases, and learn more about optimizing your data workflows with AI.
This webinar is ideal for professionals seeking to harness the power of AI within their data management systems while ensuring high levels of customization and security. Whether you're a novice or an expert, gain actionable insights and strategies to elevate your data processes. Join us to see how FME and AI can revolutionize how you work with data!
Programming Foundation Models with DSPy - Meetup SlidesZilliz
Prompting language models is hard, while programming language models is easy. In this talk, I will discuss the state-of-the-art framework DSPy for programming foundation models with its powerful optimizers and runtime constraint system.
UiPath Test Automation using UiPath Test Suite series, part 6DianaGray10
Welcome to UiPath Test Automation using UiPath Test Suite series part 6. In this session, we will cover Test Automation with generative AI and Open AI.
UiPath Test Automation with generative AI and Open AI webinar offers an in-depth exploration of leveraging cutting-edge technologies for test automation within the UiPath platform. Attendees will delve into the integration of generative AI, a test automation solution, with Open AI advanced natural language processing capabilities.
Throughout the session, participants will discover how this synergy empowers testers to automate repetitive tasks, enhance testing accuracy, and expedite the software testing life cycle. Topics covered include the seamless integration process, practical use cases, and the benefits of harnessing AI-driven automation for UiPath testing initiatives. By attending this webinar, testers, and automation professionals can gain valuable insights into harnessing the power of AI to optimize their test automation workflows within the UiPath ecosystem, ultimately driving efficiency and quality in software development processes.
What will you get from this session?
1. Insights into integrating generative AI.
2. Understanding how this integration enhances test automation within the UiPath platform
3. Practical demonstrations
4. Exploration of real-world use cases illustrating the benefits of AI-driven test automation for UiPath
Topics covered:
What is generative AI
Test Automation with generative AI and Open AI.
UiPath integration with generative AI
Speaker:
Deepak Rai, Automation Practice Lead, Boundaryless Group and UiPath MVP
Building Production Ready Search Pipelines with Spark and MilvusZilliz
Spark is the widely used ETL tool for processing, indexing and ingesting data to serving stack for search. Milvus is the production-ready open-source vector database. In this talk we will show how to use Spark to process unstructured data to extract vector representations, and push the vectors to Milvus vector database for search serving.
Building Production Ready Search Pipelines with Spark and Milvus
Ball valve
1. 1352-SERIES Data Sheet Ref. No : SU-1352-00001
Electrically Operated Ball Valve MODEL NO.: SUDE
Technical Specifications 13525040BSPRBCSS6TPROP PUNE / BANGALORE
SD-1000-05CPT200POT2LSSERVO
Quotation Ref. No
Quotation Date
1. ITEM ASSEMBLY OF 2 WAY BALL VALVE FITTED WITH
SINGLE PHASE QUARTER TURN ELECTRIC ACTUATOR
2. MAKE SUDE
3 APPLICATION Water Industries
6 TECHNICAL SPECIFICATION OF 2 WAY BALL VALVE
Valve Size 50mm
Port Size 40mm
End connection BSP Screwed
Body Material Carbon Steel
Ball Material SS316
Seating material Teflon
Flowing medium Non-injurious to Body Ball & Seals
Pressure 10 Bar
Reduce Bore Single piece design, Antistatic fire safe
Type of construction
Ball valve
Temperature Ambient
Characteristic Proportionate
Sdtork Make Single Phase Quarter Turn Electric
Fitted with
Actuator Supply Voltage 230 V AC.
ACTUATOR DETAILS
3.1 Model SD-1000-05
3.2 Output motion type Linear
3.3 Output Torque ( Nm ) 50 Nm
3.4 Output speed ( Sec/90 °) 17 sec/90°
3.5 Manual hand wheel PROVIDED
3.6 Travel limit switches Type : 1 NO + 1 NC, change over contact, contact rating:
2 Nos 5 A, 230 V AC
3.7 Torque limit switches Not required, AS 1000-series actuator are provided with
stall duty motor
3.8 Local indicator PROVIDED
3.9 Class of Protection IP67
3.10 Weight of the actuator (Kgs.) 9 kgs.
3.11 Duty S2-10 min
3.12 Mounting
3.14 G. A. Drawing Reference No
3.15 Electrical Wiring Diagram Ref, No
MOTOR DETAILS
4.1 Type Reversible Single Phase Synchronous Stall Duty Motor
4.2 Supply 230 V +/- 10 %, 50 Hz +/- 5 % AC Supply
4.3 Duty S2-10 min / S-4-30 % 1200 Cycles/ hr.
2. 4.4 Insulation Class F
4.5 Rating ( Watts) 110 Watts
OPTIONAL ACCESSORIES
5.1 Feedback Out put : 100-235 Ohms Provided
Potentiometer
5.2 Additional Limit Qty : 2 nos. Provided
Switches Type : 1 NO + 1 NC, Change over contact,
Contact rating: 5 A, 230VAC
5.3 Two Wire Transmitter Type : Two wire, Actuator mounted Provided
Supply : 12-36 VDC, Output : 4-20 m A
5.4 Remote Position Available in servo controller Provided
indicator Digital : 0-100 %
5.5 Servo controller Input signal : 4-20 m A, Output : 4-20 m A Provided
(Valve positioner) Feed back : 0-500 Ohms, supply 230 V AC,
Panel Mounted This will have auto calibration facility.
5.6 Interface Card Input signal : 4-20 m A, Provided
Feed back : 100-235 Ohms,
5.7 Local Push Button This will consist of Auto /Off / Manual Provided
Station selector switch, Open/Close push buttons.
6 GENERAL POINTS
6.1 Inspection By Customer at our works
6.2 T. C.& Manuals 2 Sets with unit
6.3 Warranty 18 months from the date of supply or 12 months from the date of installation
which ever is earlier.
6.4 Packing Thermo cool Packing Housed in corrugated Box
SPECIAL NOTE :
3. 1352-SERIES Data Sheet Ref. No : SD-1352-00002
Electrically Operated Ball Valve MODEL NO.: SUDE
Technical Specifications 13525040BSPRBCSS6TONF PUNE / BANGALORE
SD-1000-052LS
Quotation Ref. No
Quotation Date
1. ITEM ASSEMBLY OF 2 WAY BALL VALVE FITTED WITH
SINGLE PHASE QUARTER TURN ELECTRIC ACTUATOR
2. MAKE SUDE
3 APPLICATION Water Industries
6 TECHNICAL SPECIFICATION OF 2 WAY BALL VALVE
Valve Size 50mm
Port Size 40mm
End connection BSP Screwed
Body Material Carbon Steel
Ball Material SS316
Seating material Teflon
Flowing medium Non-injurious to Body Ball & Seals
Pressure 10 Bar
Reduce Bore Single piece design, Antistatic fire safe
Type of construction
Ball valve
Temperature Ambient
Characteristic On/Off Type
Sdtork Make Single Phase Quarter Turn Electric
Fitted with
Actuator Supply Voltage 230 V AC.
ACTUATOR DETAILS
3.1 Model SD-1000-05
3.2 Output motion type Linear
3.3 Output Torque ( Nm ) 50 Nm
3.4 Output speed ( Sec/90 °) 17 sec/90°
3.5 Manual hand wheel PROVIDED
3.6 Travel limit switches Type : 1 NO + 1 NC, change over contact, contact rating:
2 Nos 5 A, 230 V AC
3.7 Torque limit switches Not required, AS 1000-series actuator are provided with
stall duty motor
3.8 Local indicator PROVIDED
3.9 Class of Protection IP67
3.10 Weight of the actuator (Kgs.) 9 kgs.
3.11 Duty S2-10 min
3.12 Mounting
3.14 G. A. Drawing Reference No
3.15 Electrical Wiring Diagram Ref, No
MOTOR DETAILS
4.1 Type Reversible Single Phase Synchronous Stall Duty Motor
4.2 Supply 230 V +/- 10 %, 50 Hz +/- 5 % AC Supply
4. 4.3 Duty S2-10 min / S-4-30 % 1200 Cycles/ hr.
4.4 Insulation Class F
4.5 Rating ( Watts) 110 Watts
OPTIONAL ACCESSORIES
5.1 Feedback Out put : 100-235 Ohms Not Provided
Potentiometer
5.2 Additional Limit Qty : 2 nos. Provided
Switches Type : 1 NO + 1 NC, Change over contact,
Contact rating: 5 A, 230VAC
5.3 Two Wire Transmitter Type : Two wire, Actuator mounted Not Provided
Supply : 12-36 VDC, Output : 4-20 m A
5.4 Remote Position Available in servo controller Not Provided
indicator Digital : 0-100 %
5.5 Servo controller Input signal : 4-20 m A, Output : 4-20 m A Not Provided
(Valve positioner) Feed back : 0-500 Ohms, supply 230 V AC,
Panel Mounted This will have auto calibration facility.
5.6 Interface Card Input signal : 4-20 m A, Not Provided
Actuator Mounted Feed back : 100-235 Ohms,
5.7 Local Push Button This will consist of Auto /Off / Manual Not Provided
Station selector switch, Open/Close push buttons.
6 GENERAL POINTS
6.1 Inspection By Customer at our works
6.2 T. C.& Manuals 2 Sets with unit
6.3 Warranty 18 months from the date of supply or 12 months from the date of installation
which ever is earlier.
6.4 Packing Thermo cool Packing Housed in corrugated Box
SPECIAL NOTE :
5. 1358-SERIES Data Sheet Ref. No : SU-1358-00001
Electrically Operated Plastic Ball MODEL NO.: SUDE
Valve Technical Specifications 135850PVCPVCTPROPBSPSD- PUNE / BANGALORE
1000-052LSPOTSERVOCPT200
Quotation Ref. No
Quotation Date
1. ITEM ASSEMBLY OF 2 WAY PLASTIC BALL VALVE FITTED
WITH SINGLE PHASE QUARTER TURN ELECTRIC
ACTUATOR
2. MAKE SUDE
3 APPLICATION
6 TECHNICAL SPECIFICATION OF 2 WAY BALL VALVE
Valve Size 50mm
End connection BSP Screwed
Body Material PVC
Ball Material PVC
Seating material Teflon
Flowing medium Acid
Pressure 10 Bar
Temperature Ambient
Characteristic Proportionate
Sdtork Make Single Phase Quarter Turn Electric
Fitted with
Actuator Supply Voltage 230 V AC.
ACTUATOR DETAILS
3.1 Model SD-1000-05
3.2 Output motion type Linear
3.3 Output Torque ( Nm ) 50 Nm
3.4 Output speed ( Sec/90 °) 17 sec/90°
3.5 Manual hand wheel PROVIDED
3.6 Travel limit switches Type : 1 NO + 1 NC, change over contact, contact rating:
2 Nos 5 A, 230 V AC
3.7 Torque limit switches Not required, AS 1000-series actuator are provided with
stall duty motor
3.8 Local indicator PROVIDED
3.9 Class of Protection IP65
3.10 Weight of the actuator (Kgs.) 9 kgs.
3.11 Duty S2-10 min
3.12 Mounting
3.14 G. A. Drawing Reference No
3.15 Electrical Wiring Diagram Ref, No
3.16 Weight of Actuator – Kgs
MOTOR DETAILS
4.1 Type Reversible Single Phase Synchronous Stall Duty Motor
4.2 Supply 230 V +/- 10 %, 50 Hz +/- 5 % AC Supply
4.3 Duty S2-10 min / S-4-30 % 1200 Cycles/ hr.
4.4 Insulation Class F
4.5 Rating ( Watts) 110 Watts
OPTIONAL ACCESSORIES
6. 5.1 Feedback Out put : 100-235 Ohms Provided
Potentiometer
5.2 Additional Limit Qty : 2 nos. Provided
Switches Type : 1 NO + 1 NC, Change over contact,
Contact rating: 5 A, 230VAC
5.3 Two Wire Transmitter Type : Two wire, Actuator mounted Provided
Supply : 12-36 VDC, Output : 4-20 m A
5.4 Remote Position Available in servo controller Provided
indicator Digital : 0-100 %
5.5 Servo controller Input signal : 4-20 m A, Output : 4-20 m A Provided
(Valve positioner) Feed back : 0-500 Ohms, supply 230 V AC,
Panel Mounted This will have auto calibration facility.
5.6 Interface Card Input signal : 4-20 m A, Provided
Feed back : 100-235 Ohms,
5.7 Local Push Button This will consist of Auto /Off / Manual Provided
Station selector switch, Open/Close push buttons.
6 GENERAL POINTS
6.1 Inspection By Customer at our works
6.2 T. C.& Manuals 2 Sets with unit
6.3 Warranty 18 months from the date of supply or 12 months from the date of installation
which ever is earlier.
6.4 Packing Thermo cool Packing Housed in corrugated Box
SPECIAL NOTE :
7. 1358-SERIES Data Sheet Ref. No : SU-1358-00002
Electrically Operated Plastic Ball MODEL NO.: SUDE
Valve Technical Specifications 135850PVCPVCTONFBSPSD- PUNE / BANGALORE
1000-052LS
Quotation Ref. No
Quotation Date
1. ITEM ASSEMBLY OF 2 WAY PLASTIC BALL VALVE FITTED
WITH SINGLE PHASE QUARTER TURN ELECTRIC
ACTUATOR
2. MAKE SUDE
3 APPLICATION
6 TECHNICAL SPECIFICATION OF 2 WAY BALL VALVE
Valve Size 50mm
End connection BSP Screwed
Body Material PVC
Ball Material PVC
Seating material Teflon
Flowing medium Acid
Pressure 10 Bar
Temperature Ambient
Characteristic On/Off Type
Sdtork Make Single Phase Quarter Turn Electric
Fitted with
Actuator Supply Voltage 230 V AC.
ACTUATOR DETAILS
3.1 Model SD-1000-05
3.2 Output motion type Linear
3.3 Output Torque ( Nm ) 50 Nm
3.4 Output speed ( Sec/90 °) 17 sec/90°
3.5 Manual hand wheel PROVIDED
3.6 Travel limit switches Type : 1 NO + 1 NC, change over contact, contact rating:
2 Nos 5 A, 230 V AC
3.7 Torque limit switches Not required, AS 1000-series actuator are provided with
stall duty motor
3.8 Local indicator PROVIDED
3.9 Class of Protection IP67
3.10 Weight of the actuator (Kgs.) 9 kgs.
3.11 Duty S2-10 min
3.12 Mounting
3.14 G. A. Drawing Reference No
3.15 Electrical Wiring Diagram Ref, No
MOTOR DETAILS
4.1 Type Reversible Single Phase Synchronous Stall Duty Motor
4.2 Supply 230 V +/- 10 %, 50 Hz +/- 5 % AC Supply
4.3 Duty S2-10 min / S-4-30 % 1200 Cycles/ hr.
4.4 Insulation Class F
4.5 Rating ( Watts) 110 Watts
OPTIONAL ACCESSORIES
8. 5.1 Feedback Out put : 100-235 Ohms Not Provided
Potentiometer
5.2 Additional Limit Qty : 2 nos. Provided
Switches Type : 1 NO + 1 NC, Change over contact,
Contact rating: 5 A, 230VAC
5.3 Two Wire Transmitter Type : Two wire, Actuator mounted Not Provided
Supply : 12-36 VDC, Output : 4-20 m A
5.4 Remote Position Available in servo controller Not Provided
indicator Digital : 0-100 %
5.5 Servo controller Input signal : 4-20 m A, Output : 4-20 m A Not Provided
(Valve positioner) Feed back : 0-500 Ohms, supply 230 V AC,
Panel Mounted This will have auto calibration facility.
5.6 Interface Card Input signal : 4-20 m A, Not Provided
Actuator Mounted Feed back : 100-235 Ohms,
5.6 Control Panel This will consist of 2 nos. of Control Relay Not Provided
with required control voltage (If not specify,
control voltage will be 230 VAC ) Auto /
Manual selector switch, Open/Close push
buttons, emergency stop button & MCB.
5.7 Local Push Button This will consist of Auto /Off / Manual Not Provided
Station selector switch, Open/Close push buttons.
6 GENERAL POINTS
6.1 Inspection By Customer at our works
6.2 T. C.& Manuals 2 Sets with unit
6.3 Warranty 18 months from the date of supply or 12 months from the date of installation
which ever is earlier.
6.4 Packing Thermo cool Packing Housed in corrugated Box
SPECIAL NOTE :
9. 1362-SERIES Data Sheet Ref. No : SU-1362-00001
Pneumatically Operated Ball MODEL NO.: SUDE
Valve Technical Specifications 13625040BSPRBCSS6TPROPDA0 PUNE / BANGALORE
5VPITPPT
Quotation Ref. No
Quotation Date
1. ITEM ASSEMBLY OF 2 WAY BALL VALVE FITTED PNEUMATIC
ROTARY DOUBLE ACTING ACTUATOR
2. MAKE SUDE
3 APPLICATION Water Industries
6 TECHNICAL SPECIFICATION OF 2 WAY BALL VALVE
Valve Size 50mm
Port Size 40mm
End connection BSP Screwed
Body Material Carbon Steel
Ball Material SS316
Seating material Teflon
Flowing medium Non-injurious to Body Ball & Seals
Pressure 10 Bar
Reduce Bore Single piece design, Antistatic fire safe Ball
Type of construction
valve
Temperature Ambient
Characteristic Proportionate
Sude Make Pneumatic DA05 Double Acting Actuator,
Fitted with Signal Pressure: 5.5 to 8.5 bar, Quality of air: Filtered &
Clean Dry Air
4 PNEUMATIC ACTUATOR DETAILS
4.1 Type Double
4.2 Model DA05
4.3 Spring Clip Steel
4.4 Double Acting Cap Aluminium Alloy
4.5 Cap O-Ring N.B.R
4.6 Piston Polyarilamide
4.7 Cylinder Aluminium Alloy
4.8 Washer Polyamide
4.9 Spring Clip Steel
4.9 Position Indicator Polyamide
4.10 Piston Guide Polyacetal
4.11 Guide Ring Polyacetal
4.12 Piston O-Ring N.B.R
4.13 O-Ring N.B.R
4.14 Springs Set DIN-17223-C
4.15 Spring Return Cap Aluminium Alloy
4.16 Shaft AISI-303 Stainless Steel
4.17 Signal Pressure 5.5 to 8.5 Bar
10. 4.18 Quality Of Air Filtered & Clean Dry Air
4.19 Opening and Closing Time 0.28 [Open] & 0.28 [Close]
5 OPTIONAL ACCESSORIES
5.1 Valve Positioner Input signal: 60 PSI & 3 to 15 PSI Provided
5.2 I to P Converter Input signal: 22 PSI & 4-20mA Provided
5.3 Position Output: 4-20mA Provided
Transmitter
6 GENERAL POINTS
6.1 Inspection By Customer at our works
6.2 T. C.& Manuals 2 Sets with unit
6.3 Warranty 18 months from the date of supply or 12 months from the date of
installation which ever is earlier.
6.4 Packing Thermo cool Packing Housed in corrugated Box
SPECIAL NOTE :
11. 1362-SERIES Data Sheet Ref. No : SU-1362-00002
Pneumatically Operated Ball MODEL NO.:
Valve Technical Specifications 13622520RBS6S6TONFFL15DA00
1182B2WNCMID063.1BSPBRS4BN SUDE
ONFSPC1230VACGP1182B2WNCMI PUNE / BANGALORE
D158.0BSPS4S4BNONFSPC2230VA
CGP
Quotation Ref. No
Quotation Date
1. ITEM ASSEMBLY OF 2 WAY BALL VALVE FITTED PNEUMATIC
ROTARY DOUBLE ACTING ACTUATOR
2. MAKE SUDE
3 APPLICATION Oil Weighing Machine
6 TECHNICAL SPECIFICATION OF 2 WAY BALL VALVE
Valve Size 25mm
Port Size 20mm
End connection Flanged to ASA150RF
Body Material SS316
Ball Material SS316
Seating material Teflon
Flowing medium Oil
Pressure 10 Bar
Type of construction Reduce Bore Single piece design
Temperature Ambient
Characteristic On/Off Type
Sude Make Pneumatic DA00 Double Acting Actuator, Signal
Fitted with Pressure: 5.5 to 8.5 bar, Quality of air: Filtered and
Lubricated
4 PNEUMATIC ACTUATOR DETAILS
4.1 Type Double
4.2 Model DA00
4.3 Spring Clip Steel
4.4 Double Acting Cap Aluminium Alloy
4.5 Cap O-Ring N.B.R
4.6 Piston Polyarilamide
4.7 Cylinder Aluminium Alloy
4.8 Washer Polyamide
4.9 Spring Clip Steel
4.9 Position Indicator Polyamide
4.10 Piston Guide Polyacetal
4.11 Guide Ring Polyacetal
4.12 Piston O-Ring N.B.R
4.13 O-Ring N.B.R
4.14 Springs Set DIN-17223-C
4.15 Spring Return Cap Aluminium Alloy
4.16 Shaft AISI-303 Stainless Steel
12. 4.17 Signal Pressure 5.5 to 8.5 Bar
4.18 Quality Of Air Filtered and Lubricated
4.19 Opening and Closing Time 0.28 [Open] & 0.28 [Close]
5 OPTIONAL ACCESSORIES
5.1 Two Numbers 2 Normally Closed Construction of ¼” size – 1 no. Provided
Way Midget type & ½” – 1 no. having Coil voltage of 230 V AC
Supply in General Purpose Housing, Input signal:
Direct Acting
Pulse from the controller
Solenoid Valve
6 GENERAL POINTS
6.1 Inspection By Customer at our works
6.2 T. C.& Manuals 2 Sets with unit
6.3 Warranty 18 months from the date of supply or 12 months from the date of installation
which ever is earlier.
6.4 Packing Thermo cool Packing Housed in corrugated Box
SPECIAL NOTE :
13. 1362-SERIES Data Sheet Ref. No : SU-1362-00003
Pneumatically Operated Ball MODEL NO.:
1362200150RBS6S6TONFFL15DA40
SUDE
Valve Technical Specifications PUNE / BANGALORE
1184D4W5P3PDCPOP066.0BSPALS4B
NSPC1230VACGPWPLSBFRLGB
Quotation Ref. No
Quotation Date
1. ITEM ASSEMBLY OF 2 WAY BALL VALVE FITTED PNEUMATIC
ROTARY DOUBLE ACTING ACTUATOR
2. MAKE SUDE
3 APPLICATION Water / Oil Industries
6 TECHNICAL SPECIFICATION OF 2 WAY BALL VALVE
Valve Size 200mm
Port Size 150mm
End connection Flanged to ASA150RF
Body Material SS316
Ball Material SS316
Seating material Teflon
Flowing medium Non-injurious to Body Ball & Seals
Pressure 10 Bar
Reduce Bore Single piece design, Antistatic fire safe Ball
Type of
construction valve
Temperature Ambient
Characteristic On/Off Type
Sude Make Pneumatic DA40 Double Acting Actuator, Signal
Fitted with Pressure: 5.5 to 8.5 bar, Quality of air: Filtered and
Lubricated
4 PNEUMATIC ACTUATOR DETAILS
4.1 Type Double
4.2 Model DA40
4.3 Spring Clip Steel
4.4 Double Acting Cap Aluminium Alloy
4.5 Cap O-Ring N.B.R
4.6 Piston Polyarilamide
4.7 Cylinder Aluminium Alloy
4.8 Washer Polyamide
4.9 Spring Clip Steel
4.9 Position Indicator Polyamide
4.10 Piston Guide Polyacetal
4.11 Guide Ring Polyacetal
4.12 Piston O-Ring N.B.R
4.13 O-Ring N.B.R
4.14 Springs Set DIN-17223-C
4.15 Spring Return Cap Aluminium Alloy
4.16 Shaft AISI-303 Stainless Steel
14. 4.17 Signal Pressure 5.5 to 8.5 Bar
4.18 Quality Of Air Filtered and Lubricated
4.19 Opening and Closing 0.28 [Open] & 0.28 [Close]
Time
5 OPTIONAL ACCESSORIES
5.1 4 Way 5 Port 3 Of ¼” size having Aluminum body with Coil Provided
position Double voltage of 230 V AC Supply
Coil poppet type
solenoid valve
5.2 Weather Proof Consisting of 2 nos micro switches having 1 NO + Provided
Limit switch box 1 NC contacts for sensing end position of the
valve
5.3 Filter Regulator & Of ¼” Size supplied with Gauge Provided
Lubricator
5.4 Gear Box For Manual operation Provided
6 GENERAL POINTS
6.1 Inspection By Customer at our works
6.2 T. C.& Manuals 2 Sets with unit
6.3 Warranty 18 months from the date of supply or 12 months from the date of installation
which ever is earlier.
6.4 Packing Thermo cool Packing Housed in corrugated Box
SPECIAL NOTE :
15. 1368-SERIES Data Sheet Ref. No : SU-1368- 00001
Pneumatically Operated Plastic 136850BSPPVCPVCTPROPDA05EP SUDE
Ball Valve Technical POSFBPT PUNE / BANGALORE
Specifications
Quotation Ref. No
Quotation Date
1. ITEM ASSEMBLY OF 2 WAY PLASTIC BALL VALVE FITTED
PNEUMATIC ROTARY DOUBLE ACTING ACTUATOR
2. MAKE SUDE
3 APPLICATION
6 TECHNICAL SPECIFICATION OF 2 WAY BALL VALVE
Valve Size 50mm
End connection BSP Screwed
Body Material PVC
Ball Material PVC
Seating material Teflon
Flowing medium Acid
Pressure 10 Bar
Temperature Ambient
Characteristic Proportionate
Sude Make Pneumatic DA05 Double Acting Actuator, Signal
Fitted with Pressure: 5.5 to 8.5 bar, Quality of air: Filtered & Clean
Dry Air
4 PNEUMATIC ACTUATOR DETAILS
4.1 Type Double
4.2 Model DA05
4.3 Spring Clip Steel
4.4 Double Acting Cap Aluminium Alloy
4.5 Cap O-Ring N.B.R
4.6 Piston Polyarilamide
4.7 Cylinder Aluminium Alloy
4.8 Washer Polyamide
4.9 Spring Clip Steel
4.9 Position Indicator Polyamide
4.10 Piston Guide Polyacetal
4.11 Guide Ring Polyacetal
4.12 Piston O-Ring N.B.R
4.13 O-Ring N.B.R
4.14 Springs Set DIN-17223-C
4.15 Spring Return Cap Aluminium Alloy
4.16 Shaft AISI-303 Stainless Steel
4.17 Signal Pressure 5.5 to 8.5 Bar
4.18 Quality Of Air Filtered & Clean Dry Air
4.19 Opening and Closing 0.28 [Open] & 0.28 [Close]
Time
16. 5 OPTIONAL ACCESSORIES
5.1 Siemens make Having Input supply: 60 PSI & 4-20mA, Output Provided
Electro Pneumatic supply: 4-20mA, Inbuilt with Position Transmitter
Positioner
6 GENERAL POINTS
6.1 Inspection By Customer at our works
6.2 T. C.& Manuals 2 Sets with unit
6.3 Warranty 18 months from the date of supply or 12 months from the date of installation
which ever is earlier.
6.4 Packing Thermo cool Packing Housed in corrugated Box
SPECIAL NOTE :
17. 1368-SERIES Data Sheet Ref. No : SU-1368-00002
SUDE
Pneumatically Operated Plastic MODEL NO.: PUNE / BANGALORE
Ball Valve Technical 136850BSPPVCPVCTONFDA05AF
Specifications RALR2FCVWPLSB
Quotation Ref. No
Quotation Date
1. ITEM ASSEMBLY OF 2 WAY PLASTIC BALL VALVE FITTED
PNEUMATIC ROTARY DOUBLE ACTING ACTUATOR
2. MAKE SUDE
3 APPLICATION
6 TECHNICAL SPECIFICATION OF 2 WAY BALL VALVE
Valve Size 50mm
End connection BSP Screwed
Body Material PVC
Ball Material PVC
Seating material Teflon
Flowing medium Acid
Pressure 10 Bar
Temperature Ambient
Characteristic On/Off Type
Sude Make Pneumatic DA05 Double Acting Actuator,
Fitted with Signal Pressure: 5.5 to 8.5 bar, Quality of air: Filtered
and Lubricated
4 PNEUMATIC ACTUATOR DETAILS
4.1 Type Double
4.2 Model DA05
4.3 Spring Clip Steel
4.4 Double Acting Cap Aluminium Alloy
4.5 Cap O-Ring N.B.R
4.6 Piston Polyarilamide
4.7 Cylinder Aluminium Alloy
4.8 Washer Polyamide
4.9 Spring Clip Steel
4.9 Position Indicator Polyamide
4.10 Piston Guide Polyacetal
4.11 Guide Ring Polyacetal
4.12 Piston O-Ring N.B.R
4.13 O-Ring N.B.R
4.14 Springs Set DIN-17223-C
4.15 Spring Return Cap Aluminium Alloy
4.16 Shaft AISI-303 Stainless Steel
4.17 Signal Pressure 5.5 to 8.5 Bar
4.18 Quality Of Air Filtered and Lubricated
4.19 Opening and Closing Time 0.28 [Open] & 0.28 [Close]
18. 5 OPTIONAL ACCESSORIES
5.1 Air Filter Regulator Of ¼” Size supplied with Gauge Provided
5.2 Air Lock Relay Provided
5.3 Flow Control valve 2 nos for Slow opening & Slow closing Provided
5.2 Weather Proof Consisting of 2 nos micro switches having 1 Provided
Limit switch box NO + 1 NC contacts for sensing end position of
the valve
6 GENERAL POINTS
6.1 Inspection By Customer at our works
6.2 T. C.& Manuals 2 Sets with unit
6.3 Warranty 18 months from the date of supply or 12 months from the date of
installation which ever is earlier.
6.4 Packing Thermo cool Packing Housed in corrugated Box
SPECIAL NOTE :