shree samarth project solution: 9765006651

1. Automatic pneumatic lifter
Shree Samarth project solution (9765006651) Page 1
SAMARTH PROJECT SOLUTION
MECHANICAL / ELECTRONICS/ ELECTRICAL / COMPUTER / IT
ENGINEERING PROJECT FOR POLYTECHNIC AND ENGINEERING
STUDENTS
AURANGABAD: 09765006651 / 9595897097 / 8857832351
AUTOMATIC PNEUMATIC LIFTER
ABSTRACT
Work holding and releasing is the most essential act to carry out machining.
These are commonly used in the machine shop.
1. To hold the job in proper position
2. To release the job quickly
3. To hold the job rigidly
4. To prevent vibration of the job while the machining is carried
out.
There are many types of work holding devices like machine vices swivel vices,
universal vice, pipe vice, T-Bolt’s ‘U’ clamps, Goose neck clamp, angle plate, Jigs and
fixtures etc. These are all mechanical type work holding devices. In this project we are
dealing about the pneumatic plain vice used in drilling machine. Here the loading and
unloading is quick. The job can be held more rigidly.

2. Automatic pneumatic lifter
Shree Samarth project solution (9765006651) Page 2
INTRODUCTION
There are three major types of work holding devices which are:
1. Mechanical type
2. Hydraulic type
3. Pneumatic type
In mechanical type, the screw rod is actuating the movable jaw. One end is
connected to the movable jaw and it passes through a fixed type nut. When we rotate one
end of the screw rod it will rotate in the nut and in turn moves the movable jaw. Here the
rotary motion is converted into reciprocating motion.
In Hydraulic type’s one end of the piston rod is connected to the movable jaw and
the piston slides in the cylinder. Here the hydraulic fluid actuates the movement of the
piston; this in turn actuates the movable jaw. Here the principle movement is only a
reciprocating movement. Pneumatic type is same as the hydraulic type. Here instead of
hydraulic fluid, air is used.
WORKING OPERATION
Initially starting with air compresses, its function is to compress air from a low
inlet pressure (usually atmospheric) to a higher pressure level. This is an accomplished
by reducing the volume of the air.

3. Automatic pneumatic lifter
Shree Samarth project solution (9765006651) Page 3
Air compressors are generally positive displacement units and are either of the
reciprocating piston type or the rotary screw or rotary vane types. The air compressor
used here is a typically small sized, two-stage compressor unit. It also consists of a
compressed air tank, electric rotor and pulley drive, pressure controls and instruments for
quick hook up and use. The pressure exceeds the designed pressure of the receiver a
release value provided releases the excesses air and thus stays a head of any hazards to
take place.
The compressed air goes to the solenoid valve through flow control valve. The
flow control valve is used to control the amount air flow to the cylinder. This flow is
adjusted by manually by the nap is fixed above the flow control valve. Then this air goes
to the 5/2 solenoid valve. The 5/2 solenoid valve is having one input port, two output port
and two exhaust port. The 5/2 solenoid valve is controlled by the electronic timing
control unit. The speed of the on/off the solenoid valve is controlled by this timing
control unit. The 2 outlet ports are connected to an actuator (Cylinder). The pneumatic
activates is a double acting, single rod cylinder. The cylinder output is coupled to further
purpose. The piston end has an air horning effect to prevent sudden thrust at extreme
ends.
PRINCIPLES OF WORKING
 The compressed air from the compressor reaches the solenoid valve. The solenoid
valve changes the direction of flow according to the signals from the timing
device.
 The compressed air pass through the 5/2 solenoid valve-1 and it is admitted into
the front end of the cylinder block. The air pushes the piston for the work piece
clamping. At the end of the stroke air from the solenoid valve reaches the rear end
of the cylinder block. The pressure remains the same but the area is less due to the
presence of piston rod. This exerts greater pressure on the piston, pushing it at a
faster rate thus enabling faster return stroke.

4. Automatic pneumatic lifter
Shree Samarth project solution (9765006651) Page 4
 The compressed air pass through the 5/2 solenoid valve-2 and it is admitted into
the front end of the cylinder block. The air pushes the piston, so that the work
piece is lifted. At the end of the lifting stroke air from the solenoid valve reaches
the rear end of the cylinder block.
 The pressure remains the same but the area is less due to the presence of piston
rod. This exerts greater pressure on the piston, pushing it at a faster rate thus
enabling faster return stroke.
 The stroke length of the piston can be changed by making suitable adjustment in
the timer.
ADVANTAGES:
1. Idle time of the machine is reduced.
2. When compared with the mechanical vices, it consumes less time for
clamping and unclamping the job.
3. It reduces the manual labour
4. Hence, production rate is higher
5. In this mechanism there is no backlash.
DISADVANTAGES:
1. Initial higher cost.
2. May be a choice of air leakage
3. Cylinder stroke length is constant
APPLICATIONS:
1. To hold the job rigidly while machining.
2. For quick clamping and unclamping of the job.

5. Automatic pneumatic lifter
Shree Samarth project solution (9765006651) Page 5
SUGGESTION:
This is not only meant for drilling machine vice, using a large capacity cylinder
and vice it can be used for clamping and unclamping of the job for most of the machining
processes.

6. Automatic pneumatic lifter
Shree Samarth project solution (9765006651) Page 6