This document provides a summary of Allan M. Borja's work experience. It lists his positions, employers, duties, and dates of employment over the past 20 years working in electrical installation, commissioning, and maintenance roles in the Philippines and Middle East. His most recent role was as an Environment Solution Consultant and Solid Control Operator from 2010-2015 in Indonesia. He has experience working with oil and gas companies on offshore rigs.

1. Home Address: Purok Everlasting Barangay
Sto.Ni o Tarlac City Philippinesǹ
2300
Mobile no.: +639064880292, +63939419229
Email : allan_borja2005@yahoo.co.in
ALLAN M. BORJA
Work experience Company: PT M-I SWACO INDONESIA
Beltway Office Park,Building A,3rd
floor JI.Let.Jend.T.B Simatupang No.41
Jakarta 12550,Indonesia
From: October 01, 2010 up to August 30, 2015
Position: Environment Solution ( ES Consultant Solid Control ).
Project Involved: Vico Indonesia ( Onshore Rig ) and CONOCO PHILLIPS Indonesia
( Offshore Rig Deep sea water).
Duties and responsibilities:
Preparing the Schedule set up plan for the Rig up Onshore Rig and Assisting to
the crew which is involved for the operation in the Rig.
Centrifuge Operator for Solid Removal and Barite Recovery to maintain the
MUD weight Properties, Dewatering unit, Verti – G Cutting Dryer packaged
During on Operation on Rig Done for Trouble shooting testing and repairing the
unit such as CD 518 Centrifuge HV,CD 518 Centrifuge FH STD, CD 600,Verti-G
and Screw Conveyor, Mud cleaner and Mongoose PT Shaker M&V. Mono pump
type 040.1
Company: NOV BRANDT. (NATIONAL OILWELL VARCO) Al-thuqbah K.S.A
From: November 2007 up to September 2010
Position: field Operator & Workshop Technician
Project Involved: ARAMCO OIL DRILLING. such as POL Arabia
Drilling Co, ENI Saipem Drilling Co, ADC Arabian Drilling Co,
Weatherdford Drilling Co, DALMA Drilling Co, and SINOPEC Drilling
Co.
Duties and responsibilities:
Centrifuge Operator for Solid Removal and Barite Recovery to maintain the
MUD weight.
Testing and Commissioning of king cobra Shale Shaker, Mud
Conditioner & Degasser at RIG site.
Repair and Assemble of Bowl Assembly such as Conveyor, Pillow block and
Seepex Pump for HS 3400 Centrifuge and HS 2172
Wiring and testing of Centrifuge Control Panel such as HS 3400, HS 3000 and
HS 2172 VFD.

2. Daily Routine for testing the Centrifuge after RIG DOWN from the Rig.
RIG UP, RIG DOWN of Centrifuge RIG site at any Point Saudi Arabia.
Company: ABB Contracting Co. (Supplied by: Al Hamdan Electromechanical Est.)
Position: Electrical Commissioning Technician
From: February 2005 to September 2007.
Project Involved:
SAUDI ELECTRICITY COMPANY – (SEC) Eastern Region Branch
Upgrading of 230/69/13.8KV BSP's
Dammam B.S.P.
Dammam B.S.P
Qatif B.S.P
Khobar B.S.P
Duties and responsibilities:
69kv Switch gear local control panel pre-commissioning check as per technical
general assembly drawing
Wiring verifications, visual check and continuity testing of all wiring connection
Wiring modification of control panels as per design comments to be implemented
69kv circuit breaker limit switches alignment and inter locking check for doors
and isolators
Conduct insulation testing of 69kv circuit breakers
Conduct contact resistance testing of circuit breakers, isolators and bus bar
joints using micro ohmmeter
Conduct contact resistance of bus droppers prior to energization
Attend final testing and functional activities on switch gears
Trouble shooting of electrical faults and inter locking problems
AC and DC supply Inter panel wiring check
Company: ABB Automation Co. Ltd. (Riyadh Manufacturing)
(Supplied by: Al Hamdan Electromechanical Est.)
Position: Wireman Electrician
From: June 2001 to December 2004
Duties and responsibilities:
Panel board assembly
Wiring of control circuits, indications and alarms
Wiring modification as per punch list and design comments at quality control
section
Pre-commissioning check, apparatus check as per required, wiring verification
as per schematic diagram
Assist functional testing at quality control section
Trouble shoots electrical fault.
Company: ABB Electrical Industries Co.Ltd
(Riyadh Manufacturing) (Supplied by: Al Hamdan Electromechanical
Est.)
Position: Industrial technician
From: January 1999 to April 2001
Department: low Voltage and High Voltage Department
Duties and responsibilities:
Panel board assembly.

3. Bus bar joining and circuit breaker mounting.
Conduct contact resistance of bus bar joints using micro ohmmeter.
Installation of apparatus and layout of components as per design.
Wiring of local and remote control circuits, indications, and alarms.
Wiring modification as per punch list and design comment at quality
Control section
Assist functional testing at quality control section.
Trouble shoots electrical faults
Company: ABB INDUSTRIAL PHILIPPINES, KM 8 Sucat Paranaque City
PHILIPPINES.
Position: Electrical technician
From: December 1996 to October 1998
Duties and responsibilities:
Installed electrical equipment, control panel boards and accessories
Mounting and layout of electrical components such as contactors, auxiliary
transformers, for new installed electroneumatic machines
Wiring of control circuits and auxiliary power supply
Control wiring and installation for air handling unit.
Wiring of PLC panel and variable motor controls
Pre- commissioning and wiring check as per schematic drawing
Assist for final commissioning and functional testing prior start-up
Trouble shoots electrical faults.
Company: ASIAPHIL MANUFACTURING INDUSTRIES, UN AVENUE
PACO MANILA PHILIPPINES,
Position: LEADMAN,Elecrical, Maintenance
Technician
From: January 1995 to November 1996
Duties and responsibilities:
Disassembled and assembled of Electro Magnetic Breaker’s
Pantograph motor conditioning and motor compressor
Visual check and component check of electronic control
Re-wiring of control circuit
Trouble shoots electrical faults
Attending actual train running on low speed and high speed
Commissioning test.
References
MR : Romel Espiritu ( )
MR: Wessel Pienar ( Operation Manager NOV Brandt KSA )
Personal information 41 years of age, flexible, can able to work under pressure situation. Presently working as Basic
Consultant and Operator For Solid Control Removal.
Seminars and training • Basic and advance Electrical safety
• Thorough Knowledge of using Windows 95/98/XP, MS OFFICE.

4. • SOLID Control 101 Sponsor: BRANDT NOV ( bur Dubai 27/02/2008)
• VFD Control Cabinet ( Variable Frequency Drive ) Sponsor : BRANDT NOV
• MEDIC FIRST AID Training Program Sponsor: BRANDT NOV
• PDO HSE TRAINING PASSPORT ( MUSCAT 18/12/2007 )
• HSE & H2S TRAINING ( MUSCAT 18/12/2007 up to 2010 )
• H.U.E.T INCLUDE EBS ( SUADI ARABIA 17/02/2010 UP TO 16/02/2014 )
• T-BOSIET Sponsor: PT M-I Indonesia ( Dec-05-2013up to Dec-05-2016)
• Solid Control & Centrifuge Module Sponsor: PT M-I Indonesia Nov-26 to Dec
08,2012 )
Objective To face the challenges and grab the opportunity in order to accomplish my job promises
With the capability of my knowledge.
Education [1994 - 1995] DON BOSCO COLLEGE PasongTamo Makati City, Philippines
Diploma in: Industrial Electrical Technology
Under graduate Institute of Computer Engineers. Riyadh K.S.A
Interests and activities Electrical, Electronics Installation and Control circuit Trouble Shooting
Computer, Net surfing, Basketball and House keeping.
Languages English, Tagalog and minimal Arabic and Bahasa.