This document contains construction drawings for a new regional headquarters and showroom including a ceiling plan, external wall section details, and an eaves detail. The drawings show materials, components, and specifications for the proposed building including insulation, fire protection, ventilation, structure, roofing, and facade. The drawings were produced by Dan Palmer for the Bagstock Brick Company project and include a legend, scale, and revisions.

1. 305 x 305 x 65 UC
7
8
356x171x57UB
FDFD FA
Block
Celotex CW400
board insulation 50mm
Brick
Gypframe GA1 Steel angle
Wincro WTP3C28 Movement tie
with debonding sleeve
and WC28 channel
Glasroc F Firecase 20mm
Celotex CW400
board insulation 25mm
FD
FA
Gyptone D1 tile
Hacell light
Ventilation grille
Fire Alarm
Fire Detector
Site:
Bagstock Brick Company
Claypit End
Date:
18/07/14
Drawn by:
Dan Palmer
Drawing No:
ARC505/A/01
Drawing:
Proposed ceiling plan,
Column junction plan
Scale:
1:50, 1:10
Rev:
Verity Bird
Project:
New Regional Headquarters,
Showroom and Depot
Ceiling Plan
Legend
PRODUCED BY AN AUTODESK EDUCATIONAL PRODUCT
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT

2. 61.049
57.500
61.249
61.475
64.175
65.024
65.224
2565160262700
74.5(void)
7622004016026
60.200
57.350
65.450
Outside Ground level
904
904
270012,5762
74.5(void)
200
25
160262700
FFL(G)-FFL(1):3960FFL(1)-FFL(2):3960
Window sill (G): 58.390
Window head (G): 59.750
Window sill (F1): 62.364
Window head (F1): 63.799
Window sill (F2): 66.354
Window head (F2): 67.564
Kingspan Torlock
raised access floor (26mm)
Field head cap
Locknut
25mm Kingspan board insulation
600mm full panel
Kingspan board
insulation (50mm)
DPC
Plasterboard 12.5mm
Weep hole
Kingspan Alpha
V Pedestal
Screw fixing to
perimeter panel
Cut panel
to suit
DPM
Brick
Ibstock cant brick I.PL.10.1
Block
Ibstock cant brick I.PL.15.1
Unbonded screed 65mm
Velfac aluminium cill
by installer
Interior cill finish
by installer
Cavity closer
Compriband 600 Compressible seal
by installer
Factory applied timber packer
Block footing
Block cut to fit
Concrete foundation to
engineer's recommendations
20x90mm 'O' foam.
Note: cut edge
with aluminium tape
Perimeter head cap
Ancon HRT4 wall tie with
insulation retaining clip
Weep hole
Timber packer
Filler
Waterproof cement/expanding foam
OptionalIllbruck internal
flexible foil air seal by
installer
3mm MS Galvanised fixing
lug and fixings by installer
PU expanding foam/mineral wool
insulation by installer
10mm dot and dab
Wooden skirting board (15x150mm)
Weephole
Ibstock single cant brick AN 5.1
Velfac 200
outward opening window
Insulation
Optional Illbruck
internal flexible foil air seal
by installer
Plaster board finish
by contractor
PU Expanding foam/mineral
wool insulation by installer
Compriband 600
compressible seal
by installer
Ancon AMR
masonry reinforcement
Cavity tray
Steel 'I' beam
Filler
Steel 'I' column
Gyproc screw QS25
Corner profile
15.5mm factory recessed
edge plasterboard frieze GFKD15
Adjustable hanger
24mm Gyptone
Cross Tee
24mm Gyptone main beam
Gyptone D1 edge tiles
Steel beam
Bison solid composite
concrete floor (200mm)
Bonded screed (40mm)
Kingspan board
insulation (50mm)
300mm frieze 600mm full panel
12.5
Ibstock cant stop brick PL 1.1
Ibstock single cant brick AN 5.1
Ancon SAH-UH restraint
with extended head
Ancon SAH-UF restraint
Air seal by contractor
3mm MS Galvanised Fixing Lug
and fixings by installer
Keystone cant lintel
spec: S/K-90 (CB 45mm)
Dales S/S M12 threaded
bar and aluminium bosses -
self finish (used where loading require)
Refer to manufacturer's literature.
76.2 nose detail
Dales support arm, alum PPC
(Colour: 8015
finish: Anodising)
Dales 150mm Shadex blade alum PPC
(Colour: 5002
finish: Anodising)
904
Plasterboard 12.5mm
Ibstock cant brick I.PL.15.1
Velfac aluminium cill
by installer
Interior cill finish
by installer
Cavity closer
Compriband 600 Compressible seal
by installer
Factory applied timber packer
Ancon HRT4 wall tie with
insulation retaining clip
Timber packer
FillerWaterproof cement/expanding foam
Optional Illbruck internal
flexible foil air seal by
installer
3mm MS Galvanised fixing
lug and fixings by installer
PU expanding foam/mineral wool
insulation by installer
10mm dot and dab
Site:
Bagstock Brick Company
Claypit End
Date:
18/07/14
Drawn by:
Dan Palmer
Drawing No:
ARC505/A/02
Drawing:
Key section
External wall details
Scale:
1:20, 1:10
Rev:
Verity Bird
Project:
New Regional Headquarters,
Showroom and Depot
External Wall Section Section Detail 1
Section
Detail 2
Section
Detail 1
Section
Detail 3
Section Detail 2
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT
PRODUCED BY AN AUTODESK EDUCATIONAL PRODUCT

3. Closer angle
PVC Isolating tape
3mm galvanised steel
support angle2mm powder coated
aluminium soffit panel
to gutter manufacturer's
specification
Note:
Wall lining must be fixed
and sealed to roof lining
to maintain air seal at
junction and avoid thermal
bridging. Seal around
projecting steel cantilever
2mm mill finish
aluminium gutter
Filler support flashing
Streamliner solid airseal
50mm internal profile fillers
PVC Isolating tape
PVC Isolating tape
SD100 breather membrane
Aluminium flashings must
be isolated from the
galvanised Isobar
Line of verge flashing
SpeedDeck Standing seam
metal roof system
Walkliner 0.65/0.7mm steel
Bright White sealed laps
SpeedDeck clip
Isobar spacer
30x3mm mill finish
aluminium cross restraint
atraps at 1000mm ctrs
Eaves closer flashing
Vented eaves filler block
50x50x3mm steel
support channel
to space eaves
struts at 6000mm
centres
3mm powder coated
bull nose
StramCheck vapour
Control layer
Quilt insulation
(150mm)
PVC Isolating tape
Steel stub supporting fascia
fixing to structural engineer's detail
Weephole
Ibstock single cant brick AN 5.1
Velfac 200
outward opening window
PU Expanding foam/mineral
wool insulation by installer
Compriband 600
compressible seal
by installer
Ancon AMR
masonry reinforcement
Cavity tray
Steel 'I' column
Ibstock cant stop brick PL 1.1
Ibstock single cant brick AN 5.1
Site:
Bagstock Brick Company
Claypit End
Date:
18/07/14
Drawn by:
Dan Palmer
Drawing No:
ARC505/A/03
Drawing:
Eaves detail
Scale:
1:10
Rev:
Verity Bird
Project:
New Regional Headquarters,
Showroom and Depot
Section detail 3
PRODUCED BY AN AUTODESK EDUCATIONAL PRODUCT
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT