Unit 4_Part 1 CSE2001 Exception Handling and Function Template and Class Temp...
461
1. Marine
Engine
3508BMain Propulsion
High Performance
CATERPILLAR®
ENGINE SPECIFICATIONS
V-8, 4-Stroke-Cycle Diesel
Bore — (mm) in . . . . . . . . . . . . . . . . . . . . . . . . 170 (6.7)
Stroke — (mm) in. . . . . . . . . . . . . . . . . . . . . . . 190 (7.5)
Displacement — (L) cu in. . . . . . . . . . . . 34.5 (2105)
Rotation (from flywheel end) . . . . . . . . . ccw or cw
Compression Ratio. . . . . . . . . . . . . . . . . . . . . . . . . . 14:1
Capacity for Liquids — (L) U.S. gal
Cooling System (engine only). . . . . . 102.7 (55)
Lube Oil System (refill) . . . . . . . . . . . . . 102.0 (50)
Oil Change Interval — hrs . . . . . . . . . . . . . . . . . . 250
Engine Weight, Net Dry
(approx) — (kg) lb . . . . . . . . . . . . . . 4623 (10 182)
1119 bkW/1500 bhp/1521 mhp @ 1925 rpm
1044 bkW/1400 bhp/1420 mhp @ 1880 rpm
970 bkW/1300 bhp/1318 mhp @ 1835 rpm
895 bkW/1200 bhp/1217 mhp @ 1785 rpm
Power produced at the flywheel will be within standard tolerances up to 50° C (122° F) combustion air
temperature measured at the air cleaner inlet, and fuel temperature up to 52° C (125° F) measured at the
fuel filter base. Power rated in accordance with NMMA procedure as crankshaft power. Reduce
crankshaft power by 3% for propeller shaft power.
Air Inlet System
Air cleaners, light duty, not installed
Aftercooler core, copper-nickel tubes,
copper fins, for sea water/air
environment
Turbocharger, water-cooled bearing
housings, 152 mm (6 in) OD straight
connection
Control System
Dual Caterpillar ADEM II electronic
engine control modules with
electronically controlled unit
injectors
Cooling System
Air separator (deaerator), shipped loose
Auxiliary sea water pump, self-priming
Coolant shunt tank, not installed
Jacket water pump, gear driven,
centrifugal
Oil cooler
Thermostats and housing, full open
temperature 92° C (198° F)
Exhaust System
Dry gas tight manifold with thermo-
laminated heat shields
Dual turbocharger with watercooled
bearing housing and thermo-
laminated heat shields
Exhaust outlet, vertical, 292 mm
(11.5 in) ID round flanged outlet
Flywheels and Flywheel Housings
Flywheel housing, SAE no. 00
Flywheel, SAE no. 00, 183 teeth
Fuel System
Electronically controlled unit injectors
Fuel filters, dual spin-on, with service
indicators, front mounted
Fuel transfer pump
Instrumentation
Electronic instrument panel
analog gauges for: oil and fuel
pressure, oil and fuel filter
differential, system DC voltage,
exhaust and water temperature,
fuel pressure, air inlet restriction
digital display for: tachometer,
hours, fuel consumption — total
and instantaneous
Lube System
Crankcase breather, top mounted
Oil filler and dipstick, RH
Oil filter, four spin-on, front mounted
Oil pump, gear type
Oil pump, gear type, scavenge
Rear sump oil pan, aluminum
Mounting System
Front trunnion
Rear pads on sides of flywheel
housing
Power Take-Offs
Accessory drive, front housing
standard rotation: lower RH, lower
LH; opposite rotation: upper and
lower RH, lower LH
Front housing, two-sided
Protection System
ADEM II Electronic Monitoring System
with customer programmable
alarm, shutdown, and deration
strategies
Emergency stop pushbutton
General
Lifting eyes, front and rear
Paint, Caterpillar yellow
Vibration damper and guard
Air pressure regulator
Air starting motor
Charging alternator, 24 volt 60 amp,
RH mounted
Coolant shunt tank removal
Crankcase explosion relief valves
Deep sump oil pan for 400-hour oil
change
Dual 24 volt electric starter motors
Duplex fuel and oil filters
Emergency oil connections, requires
deep sump oil pan
Exhaust expander and flange, 305 to
406 mm
Flexible exhaust fitting, 292 mm dia x
305 mm long
Flexible fuel lines
Horizontal exhaust outlet, 292 mm dia
Mounting feet, for rigid mounting on
parallel engine beds
Pilot house instrument panel
Pyrometer and thermocouples,
individual cylinder exh. temps.
Shell and tube-type heat exchanger
Sound isolation mounts, for military/
passenger service
Sump pump
24-volt electric prelube pump
Water level switch gauge
STANDARD EQUIPMENT ACCESSORY EQUIPMENT