The Guide Right Surgical Guide System is a system of components for the fabrication and correction of diagnostic and surgical dental implant guides in 1 or 2 dimensions.
15. #6 Alignment of the Guide Sleeve
▪ Indication: 7º correction ▪
axial cross sectional
Invivo5
Anatomage
tangential view volumetric
Cone beam image showing alignment of the guide sleeve in the #6 position.
A 7º correction is needed for this site.
16. #6
Invivo5 tangential view
FIRST
The guide sleeve has been lined up with the virtual implant.
17. 8°
# 6 site ▪ 2 mm offset guide post ▪ 8° bend
18. actual 3.0 X 2.0 mm offset guide post placed on image
▪ 8º correction ▪
computer image cross sectional view # 6
Invivo5 actual offset guide post placed on virtual image
The angular correction visualized by placing the guide post over the cone beam image.
24. Invivo5
actual 3 mmAnatomageguide post
bent
placed on software image to verify 9º correction
computer image cross sectional view #8
Invivo5 actual bent guide post placed on virtual image
25. #10 alignment of the 3 mm open guide sleeve
▪ indicating 7º angular correction ▪
occlusal cross sectional
Invivo5
Invivo5
Anatomage
Anatomage
tangential view volumetric
26. #10
Invivo5
FIRST
The guide sleeve has been lined up with the virtual implant.
27. 7°
#10 site ▪ correction requiring 7° bend is made using bending tool
28. Invivo5
actual 3 mm guide post
#10 Anatomage
placed on software image to verify 7º correction
computer image cross sectional view
Invivo5 actual guide post placed on virtual image
38. Guide Right™
Products shown in this case
3 - 3/32” drill
3 - 3 mm Guide Post
3 - 3 mm Guide Sleeve
1 – 3 X 2.0 mm Offset Magnetic Guide Post
3 - 3 mm Open Guide Sleeve
Triad® Gel
Generation ll Bending Tool
1.800.314.0065 • www.deplaque.com
DWY
39. Open Magnetic Guide Sleeve sets
3.0 mm x 5.0 mm Open Guide Sleeve (short)
3.0 mm x 8.0 mm Open Guide Sleeve (long)
3.0 mm Magnetic Guide Post Straight
3.0 mm x 1.0 mm Offset Magnetic Guide Post
2.0 mm x 8.5 mm Pilot Drills
2.0 mm x10.0 mm Pilot Drill
4.0 mm x 5.0 mm Open Guide Sleeve (short)
4.0 mm x 8.0 mm Open Guide Sleeve (long)
4.0 mm Magnetic Guide Posts Straight
4.0 mm x 1.0 mm Offset Magnetic Guide Post
2.0 x 5.0 mm Pilot Drill
2.0 x 10.0 mm Pilot Drill
40. Magnetic Guide Posts
Straight
3.0 mm od
Offset
3.0 od X 0.5 mm os
3.0 od X 1.0 mm os
3.0 od X 1.5 mm os
3.0 od X 2.0 mm os
3.0 od X 2.0 mm os
3.0 od X 3.0 mm os
41. Guide Right™
Generation ll Bending Tool
10 ° example
For more information on use of the bending tool go to
www.deplaque.com ▪ Guide Right™ Generation ll Bending Tool
42. Guide Right™
Generation ll Bending Tool
Close up of Offset Guide Posts in bending block
43. Guide Right™
Products shown in this case
3/32” Drills
3 mm Guide Posts (short)
3 mm Guide Sleeves
3 mm X 2.0 mm Offset Magnetic Guide Post
3.3 mm Open Guide sleeves
4 mm Open Guide Sleeves
1.0 mm Offset Magnetic Guide Sleeve
Triad® Gel
1.800.314.0065 • www.deplaque.com
44. Guide Right™
GENERATION II BENDING TOOL
SINGLE BEND review
Step 1 Place bending tool plate on a secure flat surface with the degree increments
at the top & the stainless steel bar with the v-cut at the bottom.
Step 2 Locate 3/32” hole in the center of the v-cut and place the bottom half of the
guide post into the hole. Tighten the set screw.
Step 3 Locate the hole in the bottom of the stylus that you will use that will fit over
the top half of the guide post (3.0 mm, 4.0 mm or 5.0 mm).
Step 4 Fit the stylus over the guide post securely with the point directed at
zero degrees and the bottom of the stylus in contact with the V block.
Step 5 Using the stylus as a lever, bend the guide post to the degree of angle of
correction. You may need to ease the point of the stylus beyond the
point of the desired degree.
Step 6 Loosen screw and remove guide post and the stylus to find the guide post
bent to the desired angle.
45. Guide Right™
GENERATION II BENDING TOOL
COMPOUND BEND overview
Step 1 Position a straight or offset guide post in the bending plate, tightening the set
screw against one of the flat surfaces on the lower half of the guide post.
Step 2 The 1st bend can be made to the right or left direction.
Step 3 The set screw is loosened and the guide post is rotated 90 ° next flat surface.
Step 4 The 2nd bend in the second plane is made after rotating the guide post up away
from the surface of the bending plate to register the stylus point back at 0 degrees.
Step 5 Slide the stylus support bar down under the stylus until it supports the stylus.
Tighten the side screws before making the second bend.
Step 6 The second bend can be made in either direction according to the x-ray.
Step 7 Remove the stylus and place the guide post back in the cast with the
appropriate side indicated by a mark facing the buccal or lingual surface.
Be sure the post is in the correct position.
If the post needs to be corrected by a linear movement an offset guide post can be used.
Off sets available in the 3 mm guide post: 0.5,1,1.5, 2.0 ,or 3.0 mm.
46. Guide Right™ by DéPlaque
Start With Precision. Place With Confidence. ™
1.800.314.0065 • www.deplaque.com