Caterpillar Cat 330D L Excavator (Prefix R2D) Service Repair Manual Instant Download.pdf

Service Repair Manual
Models
330D L Excavator

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330D L EXCAVATOR R2D
Configuration: 330D L Excavator R2D00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
C9 Engines for Caterpillar Built Machines
Media Number -RENR9579-20 Publication Date -01/02/2015 Date Updated -15/08/2018
i03582800
Gear Group (Rear) - Remove and Install
SMCS - 1206-010; 1212-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0520 Driver Gp 1
B 1P-0510 Driver Gp 1
Start By:
A. Remove the flywheel and pump drive gear. Refer to Disassembly and Assembly, "Flywheel
- Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/9(W)
w
2020/8/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...

Illustration 1 g01383883
1. Remove bolts (1) and remove retainer (2). Remove gear assembly (3) .
2. Use Tooling (A) in order to remove bushing (4) from gear assembly (3) .
3. Repeat Steps 1 and 2 for the opposite side.
2/9(W)
w
2020/8/5

4. Remove bolts (5). Remove adapter (6) and the O-ring seal.
5. Use Tooling (B) in order to remove bearing (7) from adapter assembly (6) .
6. Remove gear assembly (8) .
3/9(W)
w
2020/8/5

7. Remove cover (9) and the O-ring seal.
8. Use Tooling (B) in order to remove bearing (10) .
9. Repeat Steps 4 through 8 for the opposite side.
Installation Procedure
NOTICE
4/9(W)
w
2020/8/5

1. Lower the temperature of bearing (10). Be sure to match Dimension (B) and Dimension (C)
when you are installing bearing (10). Dimension (B) indicates the angle of the joint on
bearing (10). Dimension (B) is 15° ± 1°. Dimension (C) shows the distance from bearing
(10) to the end of the bore. Dimension (C) is 4.000 ± 0.500 mm (0.1575 ± 0.0197 inch).
5/9(W)
w
2020/8/5

2. Lower the temperature of bearing (10A). Be sure to match Dimension (D) and Dimension
(E) when you are installing bearing (10A). Dimension (D) indicates the angle of the joint on
bearing (10A). Dimension (D) is 15° ± 1°. Dimension (E) shows the distance from bearing
(10A) to the end of the bore. Dimension (E) is 4.000 ± 0.500 mm (0.1575 ± 0.0197 inch).
6/9(W)
w
2020/8/5

3. Install the O-ring seal and cover (9) .
4. Install gear assembly (8). Be sure that oil passage plug (8A) is facing outward.
7/9(W)
w
2020/8/5

5. Lower the temperature of bearing (7). Be sure to match Dimension (F) and Dimension (G)
when you are installing bearing (7) into adapter assembly (6). Dimension (F) indicates the
angle of the joint on bearing (7). Dimension (F) is 15° ± 1°. Dimension (G) shows the
distance from bearing (7) to the end of the bore. Dimension (G) is 3.500 ± 0.500 mm
(0.1378 ± 0.0197 inch).
6. Install the O-ring seal and adapter assembly (6). Install bolts (5) .
7. Repeat Steps 3 through 6 for the opposite side.
8/9(W)
w
2020/8/5

8. Lower the temperature of bearing (4). Install bearing (4) into gear assembly (3). Be sure that
each relief (H) in bearing (4) is within 2° of each relief in gear assembly (3) .
9. Position gear assembly (3) and retainer (2). Install bolts (1) .
10. Repeat Steps 8 and 9 for the opposite side.
End By: Install the flywheel and pump drive gear. Refer to Disassembly and Assembly,
"Flywheel - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Aug 5 13:06:44 UTC+0800 2020
9/9(W)
w
2020/8/5

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i04530761
Flywheel - Remove
SMCS - 1156-011
Removal Procedure
Table 1
Required Tools
A -
Guide Stud
M16 x 2 by 12inch
1
1/3(W)
w
2020/8/5

1. Remove bolts 180 degrees apart. Install Tooling (A). Remove the remaining bolts (1).
2. Fasten a suitable lifting device to flywheel (2). The weight of flywheel (2) is approximately
60 kg (130 lb).
2/3(W)
w
2020/8/5

3. Remove flywheel (2).
4. Use a hammer and a punch in order to remove the flywheel ring gear, if necessary.
5. Remove the pump drive gear, if necessary.
Wed Aug 5 13:07:39 UTC+0800 2020
3/3(W)
w
2020/8/5

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i07474888
Flywheel - Install
SMCS - 1156-012
Table 1
Required Tools
A -
Guide Stud
M16 x 2 by 12inch
2
B - Loctite 243 -
1. Install the pump drive gear, if necessary.
2. Raise the temperature of the flywheel ring gear. Do not use a torch to heat the flywheel ring
gear. Install the flywheel ring gear on the flywheel. Position the flywheel ring gear with the
part number toward the crankshaft. Allow the flywheel ring gear to cool. Use a soft hammer
to seat the flywheel ring gear against the shoulder of the flywheel.
1/3(W)
w
2020/8/5

3. Attach a suitable lifting device to flywheel (2). The weight of flywheel (2) is approximately
60 kg (130 lb).
4. Position flywheel (2) on Tooling (A).
2/3(W)
w
2020/8/5

Note: When reusing bolts (1), apply Tooling (B) to the threads.
5. Install bolts (1). Remove Tooling (A) and install remaining bolts (1). Tighten bolts evenly to
a torque of 300 ± 40 N·m (221 ± 30 lb ft).
6. Check the flywheel runout. Refer to Testing and Adjusting, "Flywheel - Inspect".
Wed Aug 5 13:08:35 UTC+0800 2020
3/3(W)
w
2020/8/5

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i05820902
Crankshaft Rear Seal - Remove
SMCS - 1161-011
Removal Procedure
Start By:
A. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/2(W)
w
2020/8/5

1. Remove bolts (2) .
2. Remove crankshaft rear seal (1) from the crankshaft.
Note: Refer to Reuse and Salvage Guidelines, SEBF8039, "Crankshaft Visual Inspection and
Magnetic Particle Inspection" for the correct inspection procedure of the crankshaft seal surface.
Note: Refer to Reuse and Salvage Guidelines, SEBF9217, "Specifications for Crankshafts C7, C9,
C-9, C10, C11, C12, C-12, C13, C-13, C15, C-15, C18, C-18, C27, C30, and C32 Engines" or the
correct specifications of the crankshaft.
Wed Aug 5 13:09:31 UTC+0800 2020
2/2(W)
w
2020/8/5

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i05857809
Crankshaft Rear Seal - Install
SMCS - 1161-012
Table 1
Required Tools
A - Loctite 7649 Primer N -
B - Loctite 620 Retaining Compound -
C 147-2675 Wear Sleeve Installer 1
NOTICE
1/3(W)
w
2020/8/5

Numerical tightening sequence for bolts (2).
Note: If required, install a crankshaft wear sleeve at engine overhaul. For more information
please refer to the following Reuse and Salvage Guidelines. Refer to Reuse and Salvage
Guidelines, SEBF9217, "Specifications for Crankshafts C7, C9, C-9, C10, C11, C12, C-12,
2/3(W)
w
2020/8/5

C13, C-13, C15, C-15, C18, C-18, C27, C30, and C32 Engines" or the correct specifications
of the crankshaft. Refer to Reuse and Salvage Guidelines, SEBF8039, "Crankshaft Visual
Inspection and Magnetic Particle Inspection" for the correct inspection procedure of the
crankshaft seal surface.
1. If a crankshaft wear sleeve is necessary, refer to Step 1.a through Step 1.d to install the
crankshaft wear sleeve. If a crankshaft wear sleeve is not necessary, refer to Step 2.
a. Clean and polish the crankshaft of imperfections.
b. Use Tooling (A) to clean the outside diameter of the crankshaft and the inside
diameter of the crankshaft wear sleeve.
c. Apply Tooling (B) to the outside diameter of the crankshaft and the inside diameter of
the crankshaft wear sleeve.
d. Use Tooling (C) to install the crankshaft wear sleeve.
Note: Leave the shipping sleeve in place to install the crankshaft rear seal. The crankshaft
rear seal must be installed dry.
Note: If the seal group, O-ring seal, and the shipping sleeve are separated, these
components should not be used.
2. Lubricate the O-ring seal with clean engine oil that is on the back of the crankshaft rear seal
(1).
3. Position crankshaft rear seal (1) and the shipping sleeve over the crankshaft. Push
crankshaft rear seal (1) in place. This will dislodge the shipping sleeve.
Note: Do not remove the shipping sleeve until bolts (2) are installed.
4. Install new bolts (2) hand tight. Then, tighten bolts (2) in numerical sequence, shown in
Illustration 2. Tighten bolts (2) to a torque of 12 ± 3 N·m (106 ± 27 lb in).
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Wed Aug 5 13:10:27 UTC+0800 2020
3/3(W)
w
2020/8/5

Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i02299056
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
A 138-7575 Link Bracket 2
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
b. Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor - Remove and Install".
1/3(W)
w
2020/8/5

Caterpillar Cat 330D L Excavator (Prefix R2D) Service Repair Manual Instant Download.pdf

Recommended

Recommended

More Related Content

Similar to Caterpillar Cat 330D L Excavator (Prefix R2D) Service Repair Manual Instant Download.pdf

Similar to Caterpillar Cat 330D L Excavator (Prefix R2D) Service Repair Manual Instant Download.pdf (6)

More from shibi1322

More from shibi1322 (20)

Recently uploaded

Recently uploaded (20)

Caterpillar Cat 330D L Excavator (Prefix R2D) Service Repair Manual Instant Download.pdf