2. Starting Pro/E and Creating new Part
Start Pro/E Wildfire.
Select [File] -> [New] from the menu bar. The dialog shown
in Figure 1.1 will pop up
3. Type the part name [Example1] in Text Box.
4. Click [OK] button (or press Enter Key). You will see the screen
shown in Figure 1.2
4. Sketching and Protrusion
1. Select the Extrude Tool icon from the tool bar at the right of the screen, as shown in Figure 1.2.
2. Select the Sketcher icon from the extrusion tool bar on the dashboard at the bottom of the screen.
3. Select the plane labeled FRONT. This will allow you to sketch in the xy plane and extrude in the z
direction
[Figure 1.3]
1. Click the Sketch button from the Section pop-up menu. Pro/E will switch to
Sketch Mode, and you will see the screen as shown in Figure 1.4
5. [Figure 1.4]
1. Close the References Dialog.
2. Select [Sketch] -> [Options] from menu bar. The dialog shown in Figure 1.5 will pop
up. Turn ON the [Grid] and [Snap To Grid], and click the green check button
6. [Figure 1.5]
7. Select [Sketch] -> [Intent Manager] from the menu bar. This will bring up the
Menu Manager shown in Figure 1.6
7. [Figure 1.6]
1. Now sketch the shape shown in Figure 1.7. Select [Line] from GEOMETRY menu of
the Menu Manager.
2. Use the left mouse button to click points A, B, C, D, E, F and A shown in Figure 1.7.
After clicking these points, press the mouse middle button
8. [Figure 1.7]
10. Select [Regenerate] from SKETCHER menu of the Menu Manager.
11. Zoom in using the wheel on the mouse or by moving the mouse up and down while holding CTRL and middle mouse button.
12. Move the sketch to the center of the screen by moving the mouse while holding the middle mouse button and the Shift key.
13. Now set the size of the shape. Follow the steps below:
Select [Dimension] from SKETCHER menu.
Click Edge2 and Edge6 with the left mouse button, and then click point A with the middle mouse button.
Click Edge1 and Edge5 with the left mouse button, and then click point B with the middle mouse button.
Click Edge2 and Edge4 with the left mouse button, and then click point c with the middle mouse button.
Click Edge3 and Edge5 with the left mouse button, and then click point D with the middle mouse button
10. [Figure 1.9]
1. Select [Modify] from SKETCHER menu.
2. Click the number that is circled by A shown in Figure 1.9. Then type the correct dimension underneath the
toolbar. In this case, type 200 in the text box, and click the check button.
3. Similarly, change the number that is circled by B to 200, by C to 50, and by D to 50.
4. Select [Regenerate], and then Select [Done] from SKETCHER menu. Pro/E will exit Sketcher Mode.
5. Type in 100 into the extrusion depth box on the dashboard and click check button.
11. [Figure 1.10]
1. Select [View] -> [Orientation] -> [Default Orientation]
from menu bar. If you followed the instructions correctly,
you will see the three-dimensional image shown in Figure
1.11.
12. [Figure 1.11]
21.While there is no real undo option in Pro/E, the model tree
can be used to modify features you have already
created. Right click on the part you wish to alter, and select
[Edit Definition] from the list of options. You can then alter
the part.
22.Select [File] -> [Save] from menu bar and click the check
button at the bottom of the screen to save the part
13. Creating Cuts
1. Select the Extrude Tool icon from the tool bar on the right of the screen, as in Step 1 of the
previous section.
2. Select the Remove Material icon from the extrusion tool bar on the dashboard, as shown in
Figure 1.12.
3. Select the Sketcher icon
[Figure 1.12]
1. Locate the bottom face of the part by using View Manager as described in Step 21 of the previous
section. Select [View] -> [View Manager] from the menu bar, and then double click [Bottom] from the pop-up
window. You should see the view shown in Figure 1.13.
2. Click on the bottom face of the part near point A in Figure 1.13 to select it as the sketching plane.
3. Change the orientation to [Bottom] on the Section menu
14. [Figure 1.13]
1. Click the Sketch button from the Section menu. Pro/E will switch to Sketch Mode.
2. Select [Sketch] -> [Intent Manager] from the menu bar.
3. Select [Line] from GEOMETRY menu.
4. Click points A, B and C shown in Figure 1.14 with the mouse left button, and then click the middle mouse butto
15. [Figure 1.14]
1. Select [Regenerate] from SKETCHER menu.
2. To dimension the cut, click E2 and E4 shown in Figure 1.15 with the left mouse
button, and then click near A with the middle mouse button. Similarly, click E1,
E3, and B. Zoom and pan if necessary
16. [Figure 1.15]
1. Select [Regenerate] from SKETCHER menu.
2. Click the dimensions at points A and B, and then change
them to 25. You should see the image shown in Figure
1.16
17. [Figure 1.16]
1. Select [Regenerate] and then Select [Done] from the
SKETCHER menu. You will see the screen shown in Figure 1.17
18. [Figure 1.17]
1. Rotate the part until you see an outline of what the cut
will look like. If the cut is outside the part as shown in
Figure 1.8, click on the yellow cutting direction arrow as
shown. The outline should now be inside the part
19. [Figure 1.18]
1. Type 100 into the Extrusion Depth box and click the check button.
2. Use the mouse to zoom and rotate the part to see it from different
angles. You should see the image shown in Figure 1.18
20. [Figure 1.18]
13.Select [File] -> [Save] from menu bar to save the part.
14.Test the information you have learned in this tutorial by
completing