Metallic bond bons chemistry 100 mcq

1. The converse of hardness is known as
(a) malleability
(b) toughness
(c) softness
(d) none of the above
Ans: c
2. On which of the following factors does the resistivity of a material depend ?
(a) Resistance of the conductor
(b) Area of the conductor section
(c) Length of the conductor
(d) All of the above
Ans: d
3. is a negatively charged particle present in an atom.
(a) Proton
(b) Neutron
(c) Electron
(d) None of the above
Ans: c
4. The formula ____ determines the number of electrons that can be accommodated in any
(a) 2n2
(6) 4n2
(c) 2n3
(d) 4ns
Ans: a
5. The tiny block formed by the arrangement of a small group of atoms is called the
SLST CHEMISTRY (H/PG) DISCUSSION www.facebook.com/groups/slstchemistry/
1 of 22

(a) unit cell
(b) space lattice
(c) either (a) or (b)
Ans: a
6. The co-ordination number of a simple cubic structure is
(a) 2
(b) 4
(c) 6
(d) 8
Ans: c
7. The covalent bond is formed by
(a) transfer of electrons between atoms
(b) sharing of electrons between atoms
(e) sharing of variable number of electrons by a variable number of atoms
Ans: b
8. A perfect conductor has
(a) zero conductivity
(b) unity conductivity
(c) infinite conductivity
Ans: c
9. The metal having the lowest temperature coefficient of resistance is
(a) gold
(b) copper
(c) aluminium
(d) kanthal
2 of 22

Ans: a
10. Commonly used conducting materials are
(a) copper
(b) aluminium
(c) both (a) and (b)
(d) copper and silver
(e) platinum and gold
Ans: c
11. Which of the following materials is preferred for transmitting electrical energy over long
(a) Copper
(b) Aluminium
(c) Steel reinforced copper
(d) Steel reinforced aluminium
Ans: d
12. The kinetic energy of a bounded electron is
(a) less than that of unbounded electron
(6) greater than that of unbounded electron
(c) equal to that of unbounded electron
(d) infinite
(e) none of the above
Ans: a
13. A highly conductive material must have
(a) highest conductivity
(b) lowest temperature co-efficient
(c) good mechanical strength
(d) good corrosion resistance
(e) easy solderable and drawable quality
(f) all of the above
3 of 22

Ans: f
14. The conductivity of a conductor can be increased by
(a) decreasing its temperature
(b) increasing its temperature
(c) decreasing its vibration
(d) increasing its vibration
Ans: a
15. Superconductivity is observed for
(a) infrared frequencies
(b) d.c. and low frequency
(c) a.c. and high frequency
(d) frequencies having no effect
Ans: b
16. The superconductivity is due to
(a) the crystal structure having no atomic vibration at 0°K
(b) all electrons interact in the super-conducting state
(c) the electrons jump into nucleus at 0°K
Ans: a
17. The value of critical field below the transition temperature will
(a) increase
(b) decrease
(c) remain unchanged
(d) any of the above
Ans: a
18. In a superconductor the value of critical density depends upon
(a) magnetic field strength
4 of 22

(b) temperature
(d) both (a) and (b)
Ans: d
19. Superconductors are becoming popular for use in
(a) generating very strong magnetic field
(b) manufacture of bubble memories
(c) generating electrostatic field
(d) generating regions free from magnetic field
Ans: a
20. High resistivity materials are used in
(a) precision instruments
(6) heating elements
(c) motor starters
(d) incandescent lamps
(e) all of the above
Ans: e
21. Mercury as an electric contact material is
(a) a liquid
(b) a metal
(c) a metal liquid
(d) a gas
Ans: c
22. An H.R.C. fuse is
(a) a ceramic body having metal and caps
(b) a wire of platinum
(c) a heavy cross-section of copper or aluminium
(d) a ceramic tube having carbon rod inside it
5 of 22

Ans: a
23. Which of the following resistive materials has the lowest temperature co-efficient of resi
(a) Nichrome
(b) Constantan
(c) Kanthal
(d) Molybdenum
Ans: a
24. The coils of D.C. motor starter are wound with wire of
(a) copper
(b) kanthal
(c) manganin
(d) nichrome
Ans: c
25. The conductors have transport phenomena of electrons due to
(a) electric field
(b) magnetic field
(c) electromagnetic field
Ans: a
26. The transition temperature of mercury is
(a) 18.0°K
(6) 9.22°K
(c) 4.12°K
(d) 1.14’K
Ans: c
27. By increasing impurity content in the metal alloy the residual resistivity always
(a) decreases
(b) increases
6 of 22

(c) remains constant
(d) becomes temperature independent
Ans: b
28. The structure sensitive property of a super conductor is
(a) critical magnetic field
(b) transition temperature
(c) critical current density
Ans: c
29. At transition temperature the value of critical field is
(a) zero
(6) negative real value
(c) positive real value
(d) complex value
Ans: a
30. Which of the following variety of copper has the best conductivity ?
(a) Induction hardened copper
(b) Hard drawn copper
(c) Pure annealed copper
(d) Copper containing traces of silicon
Ans: c
31. Constantan contains
(a) silver and tin
(b) copper and tungsten
(c) tungsten and silver
(d) copper and nickel
Ans: d
32. Which of the following is the poorest conductor of electricity ?
7 of 22

(a) Carbon
(b) Steel
(c) Silver
(d) Aluminium
Ans: a
33 ______ has zero temperature co-efficient of resistance.
(a) Aluminium
(b) Carbon
(c) Porcelain
(d) Manganin
Ans: d
34. Piezoelectric materials serve as a source of _____ .
(a) resonant waves
(b) musical waves
(c) microwaves
(d) ultrasonic waves
Ans: d
35. In thermocouples which of the following pairs is commonly used ?
(a) Copper-constantan
(b) Aluminium-tin
(c) Silver-German silver
(d) Iron-steel
Ans: a
36 is viscoelastic.
(a) Cast-iron
(6) Graphite
(c) Rubber
(d) Glass
8 of 22

Ans: c
37. Carbon electrodes are not used in
(a) GLS lamps
(b) electric arc furnace
(c) dry cells
(d) cinema projectors
Ans: a
38. Solder is an alloy of
(a) copper and aluminium
(b) tin and lead
(c) nickel, copper and zinc
(d) silver, copper and lead
Ans: b
39 ______ is most commonly used for making magnetic recording tape
(a) Silver nitrate
(b) Ferric oxide
(c) Small particles of iron
(d) Silicon-iron
Ans: b
40. Overhead telephone wires are made of
(a) aluminium
(b) steel
(c) ACSR conductors
(d) copper
Ans: b
41. ______ is an example of piezoelectric material.
(a) Glass
(b) Quartz
9 of 22

(c) Corrundum
(d) Neoprene
Ans: b
42. _____ is the main constituent of glass
(a) Fe203
(b) Si02
(c) AI2O3
(d) B2O3
Ans: b
43. A good electric contact material should have all of the following properties except
(a) high resistivity
(b) high resistance to corrosion
(c) good thermal conductivity
(d) high melting point
Ans: a
44. Most of the common metals have _____ structure.
(a) linear
(b) hexagonal
(c) orthorhombic
(d) cubic
Ans: d
45. Which of the following affect greatly the resistivity of electrical conductors ?
(a) Composition
(b) Pressure
(c) Size
(d) Temperature
Ans: a
46. Thermonic emission occurs in
10 of 22

(a) vacuum tubes
(b) copper conductors
(c) ferrite cores
(d) transistors
Ans: a
47. _____ is a hard solder.
(a) Tin-lead
(6) Tin-silver-lead
(c) Copper-zinc
(d) None of the above
Ans: c
48. Addition of 0.3 to 4.5% silicon to iron _____ the electrical resistivity of iron.
(a) increases
(b) decreases
(c) does not change
Ans: a
49. Super conductivity can be destroyed by
(a) adding impurities
(b) reducing temperatures
(c) application of magnetic field
Ans: c
50. Non-linear resistors
(a) produce harmonic distortion
(b) follows Ohm’s law at low temperatures only
(c) result in non-uniform heating
Ans: a
11 of 22

51. A carbon resistor contains
(a) carbon crystals
(b) solid carbon granules
(c) pulverized coal
(d) finely divided carbon black.
Ans: d
52. Which of the following materials does not have covalent bonds ?
(a) Organic polymers
(b) Silicon
(c) Metals
Ans: c
53. In graphite, bonding is
(a) covalent
(b) metallic
(c) Vander Waals
(d) Vander Waals and covalent
Ans: d
54. Total number of crystal systems is
(a) 2
(b) 4
(c) 7
(d) 12
Ans: c
55. The number of atoms per unit cell in B.C.C. structure is
(a) 1
(b) 2
(c) 4
(d) 8
12 of 22

Ans: b
56. The conductivity of a metal is determined by
(a) the electronic concentration and the mobility of the free electrons
(6) the number of valence electrons per atom
Ans: a
57. The resistivity of a metal is a function of temperature because
(a) the amplitude of vibration of the atoms varies with temperature
(b) the electron density varies with temperature
(c) the electron gas density varies with temperature
Ans: a
58. In a crystal, an atom vibrates at a frequency determined by
(a) the heat content of the crystal
(b) the temperature of the crystal
(c) the stiffness of the bonds it makes with neighbors
Ans: c
59. Due to which of the following reasons aluminium does not corrode in atmosphere ?
(a) Aluminium is a noble metal
(b) Atmospheric oxygen can only diffuse very slowly through the oxide layer which is forme
(c) No reaction with oxygen occurs ft Any of the above
Ans: b
60. The impurity atoms is semiconductors
(a) inject more charge carriers
(6) reduce the energy gap
(c) increase the kinetic energy of valence electrons
(d) all of the above
Ans: b
13 of 22

61. Which of the following material is not a semiconductor ?
(a) Silica
(b) Germanium
(c) Selenium
(d) Gallium-arsenide
Ans: a
62. Carbon resistors are used extensively because they are
(a) easy to make
(b) compact
(c) inexpensive
(d) all of the above reasons
Ans: d
63. Carbon rods are used in wet and dry cells because
(a) carbon rod serves as conductor
(b) carbon can resist the attack of battery acid
(d) either (a) or (b)
Ans: c
64. Due to which of the following factors the brush wear rate is altered ?
(a) Speed of the machine
(b) Contact pressure
(c) Surface conditions of brush and commutator
(d) Excessive sparking
(e) All of the above
Ans: e
65. Which of the following are non-conductors of electricity?
(a) Non-metal solids except carbon
(b) Air and most other gases
14 of 22

(c) Pure water and liquids in general except mercury
Ans: d
66. Carbon bearings are used under which of the following conditions ?
(a) Where lubrication is difficult or im-possible
(b) Where corrosive chemical action exists
(c) Where high temperature exists
Ans: d
67. Which of the following high resistance materials has the highest operating temperature
(a) Kanthal
(b) Manganin
(c) Nichrome
(d) Eureka
Ans: a
68. Steel wire is used as
(a) overhead telephone wire
(b) earth wire
(c) core wire of ACSR
Ans: d
69. Low resistivity materials are used in
(a) transformer, motor and generator windings
(b) transmission and distribution lines
(c) house wiring
(d) all above applications
Ans: d
70. Platinum is used in
15 of 22

(a) electrical contacts
(b) thermocouple
(c) heating element in high temperature furnace
(d) grids of special purpose vacuum tubes
Ans: e
71. Which of the following is an advantage of stranded conductor over equivalent single con
(a) Less liability to kink
(b) Greater flexibility
(c) Less liability to break
Ans: d
72. Due to which of the following reasons copper and aluminium are not used for heating el
(a) Both have great tendency for oxidation
(b) Both have low melting point
(c) Very large length of wires will be required
Ans: d
73. Copper, even though costly, finds use in the windings of electrical machines because
(a) copper points offer low contact resistance
(b) copper can be easily soldered and welded
(e) copper windings are less bulky and the machines become compact
Ans: d
74. Which of the following materials is used for making coils of standard resistances ?
(a) Copper
(b) Nichrome
(c) Platinum
16 of 22

(d) Manganin
Ans: d
75. Substances whose specific resistance abruptly decreases at very low temperature are call
(a) insulators
(b) conductors
(c) semiconductors
(d) superconductors
Ans: d
76. Which of the following materials is the best conductor of electricity ?
(a) Tungsten
(b) Aluminium
(c) Copper
(d) Carbon
Ans: c
77. is the property of absorbing moisture from atmosphere.
(a) Solubility
(b) Viscosity
(c) Porosity
(d) Hygroscopicity
Ans: d
78. Thermocouples are mainly used for the measurement of
(a) temperature
(b) resistance
(c) eddy currents
(d) coupling co-efficient
Ans: a
79. Due to which of the following fact, in India, aluminium is replacing copper ?
(a) Aluminium is more ductile and malleable than copper
17 of 22

(6) Aluminium is available in plenty, cheaper and lighter than copper
(c) Aluminium has lower resistivity than that of copper
(d) Aluminium has less temperature co-efficient than copper
Ans: b
80. The conduction of electricity, in semiconductors, takes place due to movement of
(a) positive ions only
(b) negative ions only
(c) positive and negative ions
(d) electrons and holes
Ans: d
81. Which of the following is a semiconductor material ?
(a) Phosphorous
(b) Rubber
(c) Silicon
(d) Aluminium
Ans: c
82. Selenium is _____ semiconductor.
(a) extrnisic
(b) intmisic
(c) N-type
(d) P-type
Ans: b
83. ________ has the best damping properties.
(a) Diamond
(b) High speed steel
(c) Mild steel
(d) Cast iron
Ans: d
18 of 22

84. The photo-electric effect occurs only when the incident light has more than a certain cri
(a) intensity
(b) speed
(c) frequency
(d) wave length
Ans: c
85. If the resistance of a conductor does not vary in accordance with Ohm’s law it is known
(a) non-linear conductor
(b) reverse conductor
(c) bad-conductor
(d) non-conductor
Ans: a
86. Spark plug makes use of which of the following materials for insulation ?
(a) Porcelain
(b) Slate
(c) Asbestos
(d) Glass
Ans: a
87. The forbidden gap in an insulator is
(a) large
(b) small
(c) nil
Ans: a
88. Which of the following factors affect resistivity of metals ?
(a) Age hardening
(b) Alloying
(c) Temperature
19 of 22

(d) Cold work
(e) All of the above
Ans: e
89. Effect of moisture on the insulating materials is to
(a) decrease dielectric constant
(b) decrease dielectric strength
(c) decrease insulation resistance
(d) increase dielectric loss
Ans: e
90. Surface resistance of an insulating material is reduced due to the
(a) smoky and dirty atmosphere
(b) humidity in the atmosphere
(d) neither (a) nor (b)
Ans: c
91. Superconducting metal in super conducting state has relative permeability of
(a) zero
(b) one
(c) negative
(d) more than one
Ans: a
92. In conductors conduction of electricity takes place due to movement of
(a) electrons only
(b) positive ions only
(c) negative ions only
(d) positive and negative ions
20 of 22

Ans: a
93. The carbon percentage is least in
(a) low carbon steel
(b) wrought iron
(c) cast iron
(d) malleable iron
Ans: b
94. For a particular material the Hall coefficient was found to be zero. The material is
(a) insulator
(6) metal
(c) intrinsic semiconductor
Ans: b
95. The conductivity of an extrinsic semiconductor with temperature
(a) decreases
(b) increases
(c) remains constant
Ans: c
96. The current due to electron flow in conduction band is the hole current in valence band.
(a) equal to
(b) less than
(c) greater than
Ans: c
97. For a hole which of the following statements is incorrect ?
(a) Holes can exist in certain semiconductors only
(b) Holes can exist in any material including conductors
(c) Holes may constitute an electric current
21 of 22

(d) Holes can be considered as a net positive charge
Ans: b
98. is an element used in semiconductors whose atoms have three valence electrons.
(a) An acceptor
(b) A donor
(c) Germanium
(d) Silicon
Ans: a
99. The minority carrier concentration is largely a function of
(a) forward biasing voltage
(b) reverse biasing voltage
(c) temperature
(d) the amount of doping
Ans: c
100. For germanium the forbidden energy gap is
(a) 0.15 eV
(b) 0.25 eV
(C) 0.5eV
(d) 0.7eV
Ans: d
22 of 22

Metallic bond bons chemistry 100 mcq

Recommended

Recommended

More Related Content

What's hot

What's hot (20)

Viewers also liked

Viewers also liked (20)

Similar to Metallic bond bons chemistry 100 mcq

Similar to Metallic bond bons chemistry 100 mcq (20)

More from M H

More from M H (12)

Recently uploaded

Recently uploaded (20)

Metallic bond bons chemistry 100 mcq