Recommended
More Related Content
What's hot
What's hot (16)
Similar to Forged body automatic push-start air tool with replaceable bushings
Similar to Forged body automatic push-start air tool with replaceable bushings (20)
Recently uploaded
Recently uploaded (20)
Forged body automatic push-start air tool with replaceable bushings
- 2. Forged body for long life. Automatic push-start mechanism. Less components for easy maintenance. Replaceable round bushing. OPTIONAL MUFFLER OPTIONAL MUFFLER OPTIONAL MUFFLER OPTIONAL MUFFLER 7/8×3-1/4 or 1×4-1/4 577 7/8×3-1/4 or 1×4-1/4 TPB-40SV 19.5 43 653.5 TPB-40SV PICK HAMMER TRENCHER & CLAY DIGGER TCB BREAKER TPB BREAKER 166 1,050 20.9 46 606 1.6 1.5 56.5 53 16 66.6 40 62 68 93 725 1.65 58.3
- 3. ● 2types of retainer, cup and spring, are available.(THA-4B) ● Four bolt handle for excellent durability and maintenance.(TCH-3&4) THA-2B THA-3B Goose Neck Handle 4-Bolt Handle THA-4B THA-4S TCH-3 TCH-4 51 64 102 63.5 101.6 2,300 2,200 1,800 2,200 1,800 6.2 6.8 7 8.6 9 13.6 15 16.1 19 20 413 450 480 406 432 0.85 0.9 0.95 0.89 0.95 30 31.8 33.5 31.5 33 22.5 50 41 31 17.8 567 583 THA-2B THA-3B THA-4B(S) TCH-3 TCH-4 TJ-20SV INSERT BIT FOR ROTARY HAMMER TJ-20SV 250,280,400,500,600,700 AA CHIPPING HAMMER for AA-1.3B. CHIPPING HAMMER SINKER ROCK DRILL ROTARY HAMMER 64 60
- 4. ● Water swivel attachment available to control dust and chips from drilling. 18 40 38.9 4.0 Water swivel Air swivel complete Wet shank Dry shank Rod size 500, 1000, 1200, 1500mm Rod connection Bit (Thread type) Gauge size 42, 48, 50, 55, 65mm Spiral rod (Thread type) TAA-400 PUT OUT mm 1,200 600-950 10.2 22.5 275 3.4 119 19 3/4 LEVER TYPE SPEED AT NO LOAD r.p.m SPEED AT LOAD r.p.m START TYPE ACCESSORIES FOR AUGER DRILL TAMPER & SAND RAMMER AIR AUGER DRILL TAA-400 600 TAMPER & SAND RAMMER ROD AIR AUGER DRILL BIT HOSE COUPLING
- 5. CHISEL TAMPING ROD AND PAD Even a little dust or moisture will affect an air tool to stop operation in some cases. Thus, an air-filter(Drain separator)and lubricator should always be equipped in the piping and also the oil in the lubricator should be checked. Air tool parts are precision machined items. Throwing, dropping or rough handling is strictly prohibited. Periodical inspection will increase the durability performance and efficiency of the air tool. Check air line frequently making sure clean air is being sent to the tool. OPERATION AND MAINTENANCE INSTRUCTIONS FOR AIR TOOLS Air Compressor Lubrication Dust-Proof and Anti-Corrosion Maintenance and Periodical inspection Air tool is greatly affected for its durability, performance and work efficiency by the way of operation and maintenance. The following instructions should carefully be obeyed in order to maintain the performance of new tool. Air tool is designed to be operated at dynamic air pressure of 5-7 kg/cm² on the pressure gauge. During operation, the air consumption is shown in the specifications for each tool. Thus the air distribution volume of an air-compressor should be larger than the total air-consumption of the tools under simultaneous use. Preferably, the air distribution volume should be 20% more than total air consumption. This is due to the loss of air and decrease in air pressure through piping. In general, the compressor to be installed to distribute 1m³ /min should have 10HP engine. The lack of air volume results in a decrease of performance for air tool. The air compressor, therefore, should have some allowance in capacity. Lubrication is very important for air tool operation. All Toku air tool is tested before delivery. However, if a defective situation or poor performance is experienced, please be sure to clean off the air tool oil by washing oil or putting a small volume of the lubricant(shown below) in the tool. Restart at slow speed gradually. Recommended lubricants and instruction for lubrication is mentioned below. other Hammers Rotary Hammers moving surface of valve and piston etc Turbine oil (ISOVG-46 or equivalent) 3cc/min by line oiler ASPHALT CUTTER
- 6. E-mail : int-op@toku-net.co.jp 812-0043, Japan Kiyama Plant 2001FSP2000 EMS 89393/ISO 14001