5. FOCUST 101
Super Degreaser
Formulate for cleaning purposes to
many kind of dirt and grime such as
grease, oil, fat and other
hydrocarbon that stick to metal
surface. Containing metal protection
corrosion inhibitor, Focust 101 very
safe to be applied in many kind of
material
Benefit
- Non flammable
- Able to dilute as per needed
- Effective to remove dirt and grime
- Contain corrosion inhibitor
- Safe to metal used
- Not cause damage to paint
5
Application
Focust 101 could be applied
manually to the surface or combine
with cleaning equipment
Packaging
Pail @ 25 Litres
Drum @ 200 Litres
6. FOCUST 103
Oil Spill Dispersant
Focust 103 is specialized formulated
to neutralize oil waste or
hydrocarbon in the water or hard
surface. Containing metal corrosion
inhibitor, Focust 103 also can be
used as degreaser for the metal
surface
Benefit
- Non flammable
- Non Toxic
- Can be dilute as per needed
- Non corrosive
- Environmental Friendly
6
Application
Focust 103 applied manually or with
high pressure wash and hand
sprayer
Packaging
Pail @ 20 Litres
Drum @ 200 Litres
7. FOCUST 202
Rust and Scale Remover
FOCUST 201P, specialized formulized
for cleaning and remove rust and
scale in the metal surface. It can be
used to remove any kind and level
of rust and scale. It’s safe to the
human and effective to remove rust
and environmental friendly. This
product is phosphate acid and
dissolve to the water
Benefit
- Non flammable
- Able to dilute as per needed
- Effective to remove rust
- Safe to metal used
- Not cause damage to paint
- Contain corrosion inhibitor
Application
Focust 202 could be applied
manually to the surface,circulated
to the plumbing equipment or
combine with cleaning equipment
Packaging
Pail @ 25 Litres
Drum @ 200 Litres 7
8. FOCUST 303
Solvent Degreaser
Fast drying solvent non flammable,
as and electric resistor. Formulate
for cleaning purposes to remove
waterproof grease and stain such as
oil sludge and other oil base stain on
the material surface or any tools
Benefit
- Non flammable
- Non Toxic
- High Dielectric Strength
- Non corrosive
- Fast Drying
8
Application
Focust 303 applied to the material
surface with sprayer then clean with
sponge or brush
Packaging
Pail @ 25 Litres
Drum @ 200 Litres
9. FOCUST 304
Rust Penetrant
Solvent, propellant hydrocarbon
base and high quality solvent.
Formulated for easy to bolt open or
other mechanical. Its high for metal
allows it to penetrate, seal out
moisture, attacking rust, lubricates
and preventing corrosion. Suitable
for petroleum industry, heavy
industry, automotive and housing
Benefit
- Non Toxic
- Odorless
- Non irritated
9
Application
Focust 304 spray on the material
surface. Wait for second to optimal
penetration at rust area
Packaging
Can @ 4 Litres
Pail @ 25 Litres
Drum @ 200 Litres
10. FOCUST 308
Paint Remover
Solvent base product and not dilute
to water. Focust 308 formulated to
remove paint and rubber deposit to
all metal surface (hard and soft
metal), glass, concrete and
aluminium. Very effective to remove
and clean paint mould plastic
Benefit
- Effective
- Economic
- Non korosif
- Remove any type of paint
10
Application
Focust 308 spray on the material
surface. Wait for minutes then clean
with pressure water, brush or
sponge
Packaging
Bottle @ 1 Litres
Pail @ 25 Litres
Drum @ 200 Litres
11. FOCUST 507
Rust Converter
Formulate to prevent rust process
on the metal. Protection rust
formulaic to give the film thick
when applied to the surface of
metal so as to hinder oxidation air
and moisture causes rust. Very fit
for prevention rust out on the
storage room in metal machinery,
and requiring automotive
equipment dicoating to prevent
from rust
Benefit
- Prevent rust for longer time
- Ease to use
- Fast reaction
- Odorless
- Non Toxic
11
Application
Clean surface material from rust and
stain before coated then applied to
the material surface using brush or
spray. Wait 30-60 minutes until it
dry
Packaging
Pail @ 25 kg
13. FOCUST BT-99P
Boiler Treatment
scale prevention agent containing a
special mixture with decomposition
and separation methods of
phosphate to prevent deposit on
boilers. Phosphate is used to settle
Calcium Hardness solution in boiler
water. Interface decomposition and
separation of floating solids of any
kind, attached to the surfaces in the
boiler. This product is recommended
for high-pressure boiler
Benefit
- Easy to use
- Economic
- Good Scale Preventer
- Reduce Fuel Consumption
13
Application
FOCUST BT- 99P must be used
continuously in a closed boiler. It is
preferable kept in a steam drum,
although the application in the pre-
boiler or feed water line is also
allowed. Maintenance dosage is 30-
50 ppm phosphate as PO4 in the
boiler water. Proper dosage
depends on the operational
conditions of the system and
optimum dosage limitation will be
determined by the technicians
Packaging
Pail @ 25 Kg
14. FOCUST BT-99H
Boiler Treatment
FOCUST BT-99H is a hydrazine
solution use as an oxygen scavenger
in boiler feed water. This product
incorporates organic catalyst of
superior quality to speed up
reaction event at a very low
temperature.
FOCUST BT-99H it doesn`t produce
dissolved solid therefore does not
increase blowdown.
This feature is very important for
high pressure boiler where dissolve
solid should be at the lowest level
Benefit
- Easy to use
- Economic
- Reduce Fuel Consumption
14
Application
A continuous dose of FOCUST BT-
99H via a chemical metering pump
is a strongly preferred. The required
dose of FOCUST BT-99H depends on
operation condition from the
system containing 0.1 – 1.0 ppm on
treatment for boiler water.
Technician will provide technical
advice on the optimum treatment
range
Packaging
Pail @ 25 Kg
15. FOCUST CL-401
Corrosion and Scale
Inhibitor
FOCUST CL-401 is Liquid compound
containing corrosion inhibitors and
sequestering agents. It can be used
for water scale and corrosion
protection for all closed fresh water
circulation systems such as :
Diesel engine cooling water systems
Compressor cooling water systems
Central heating systems
Benefit
• Prevents scale deposition
• Protection against rusting and
corrosion
• Increases heat transfer efficiency
• Non Chromate Product
15
Application
Initial treatment recommendation
for newly filled system is 1 litre of
FOCUST CL-401 per 100 litres of
fresh water in the system. After
through mixing contain a sample
and check both pH value and
phosphate content in ppm PO4.
These measured using pH 7.8 to 10
Test Kit and a Phospate Test Kit
Packaging
Pail @ 25 Kg
17. 17
FOCUST FLOC WWTP
Basic of Poly Alum Complex
coagulant, special formulated to
provide maximum coagulation in
water and waste water treatment.
Can be combined with anionic/
cationic/ non-ionic floculant (not
recommended to mix )
Physical Properties
- Appearance : Brown, Yellowish
Liquid
- Specific Gravity 250 C : 1.185 –
1.220
- Viscosity 250 C (Cps) : 4.0 – 5.0
- AL2O3 (%) : 8 ± 0.5
- Basicity (%) : 45 ± 0.5
- PH (1% Sol.) : 3.0 ± 0.5
- SO4 (%) : Max. 2%
- Fe (%) : Max. 0.01 %
- Pb, Ag, Zn : Negative
- Solubility in water : Soluble
Application
FOCUST FLOC is has application in a
wide variety of system, actual
treatment levels in water and waste
water treatment and system should
be determined by jartest (
laboratory test ) and field test with
range of dosage of 10 – 100 ppm of
100% concentration and in range of
pH 7 – 8
Packaging
Tank Lorry 10-20 Ton
18. 18
FOCUST 801
Water Treatment Coagulant
basic of Poly Alumunium Complex,
special formulated to provide
maximum coagulation in water and
waste water treatment. Can be
combined with anionic/ cationic/
non-ionic floculant ( not
recommended to mix )
Physical Properties
- Appearance : Brownish Liquid
- Concentration : 100%
- Specific Gravity 250C : 1.1 – 1.2
- Solubility in water : Soluble
- Ph ( 1% solution ) : 3 Min
Application
application in a wide variety of
system, actual treatment levels in
each system and waste water
should be determined by jartest (
laboratory test ) and field test with
range of dosage of 100 – 2000 ppm
of 100% concentration and pH of
waste water before coagulation
between 7-10, 15-50 ppm for water
treatment depend on the turbidity
Packaging
Tank Lorry 10-20 Ton
19. 19
FOCUST 505
Defoamer
DEFOAMER 5050 is active defoamer
emulsion which developed for pulp
mill specially in washing operation or
other process where foam appear
too much.
DEFOAMER 5050 is more efficient
than conventional defoamer, reduced
additive to the system and also
reduced pitch problem.
DEFOAMER 5050 is good
dispensability product and very
environmental friendly because of
inert reaction with chlor in bleaching
stage as a DBD and DBF precursor
Physical Properties
- Appearance : Milky white emulsion
- Chemical Composition : Emulsion
of silfoam
- Ionic Character : Non Ionic
- Specific Gravity : 1.01 ± 0.05 g/ml
Application
Added into system by dosing pump,
the optimum quantity and addition
are determined by
trial.
Packaging
Gallon @ 5kg
Pail @ 25kg
Drum @ 200 kg
28. +62 21 – 8493-7103
+62 812-3030-1552
+62 821-3103-3333
Contact Us
mse.chemical@gmail.com
Handito.saroso@gmail.com
Pasetyo.sigit@gmail.com
MULTI SINERGI EKATAMA CHEMICAL
Pesona Amsterdam Blok I-11 No 34
Kota Wisata Cibubur, Bogor 16968
