Step by step on how to choose your own laser machine

1. Which one
to choose?

3. Advantage of new D series CO2 laser machine
No need USB
dongle drive
Ordinary model
D series

4. LCD control panel
Hand-held control
panel
Ordinary water
chiller
Compressor water
chiller
Ordinary exhaust fan
Professional
convulsions system
Ordinary model
D series

5. built-in type fan
Outside fan Ordinary connector
Integrated connector
Ordinary model
D series

6. Ordinary air pipe
Telescopic air duct Professional two-stage ventilation pipe
Ordinary one-stage ventilation pipe
Ordinary
model
D series

7. Ordinary motion
control card
motion control
card with shield
Transfer-type USB
data cable
Direct-type USB
data cable
Ordinary
model
D series
Ordinary door holder
Inside doorknob

8. Faster roller
linear guide rail
Ordinary linear
guide rail
Open-design back cover of laser machine
Fixed back cover of laser machine
Ordinary
model
D series

9. Software of
Ordinary model
Software of D series

10. GN-D10060 GN-D13080 GN-DS160100
1000mm X 600mm 1300mm X 800mm 1600mm X 1000mm
Single-head Single-head Double-head

11. Test is finished , ready for packing

12. Equipment are packed, load in container

13. Good PriceHigh Quality
$ R$HURRY UP !
CONTACT US !

14. Technical parameter
220V,50HZ (standard) / 220V,60HZ(optional)Power supply
1600x1000mm1300x800mm
Thicker honeycomb working tableWorking table
0-1200mm/sEngraving speed
0-500mm/sCutting speed
1.2KWWhole power
Specialized compressor water chillerCooling mode
PLT, AI, DXF, DST,JPG, BMP, GIF, PNG, TGA, TIFCompatible file format
1000x600mmWorking area
70W/80W/100W/130W/150WLaser power (optional)
65WLaser power (standard)
10600nmLaser wavelength
Hermetic and detached CO2 laser tubeLaser type
GN-DS160100GN-D13080GN-D10060Model

15. Advantage of D-series CO2 laser cutting engraving machine
1. Fashion and elegant appearance, line fluency.
2. Canceled previous software controlling by soft dongle, upgraded to non-soft
dongle mode.
3. Split-type design for the machine, easy disassembly .
4. Upgraded control panel to hand-held controller, which avoid control panel
damage caused by smoke, reduce the equipment failure rates. Installing magnet
in hand-held controller, so the controller can be fixed in any place randomly.
The connection of between hand-held controller and laser equipment adopts coil
cord and aviation plugs to connect hand-held controller and laser equipment,
easy manipulation.

16. Advantage of D-series CO2 laser cutting engraving machine
5. Simplified the setting of engraving parameter, it is easier for users to set
engraving parameter. The software can match the engraving parameters
automatically to get better engraving effect.
6. Increased parameter library in the upgraded software, which can save different
parameters used for processing different material to the parameter library. Users
can call these parameter directly next time.
7. Designed the air inlet for ventilation, ensure the internal pressure balance of
working table in ventilation. It avoids the material depression in the holes of
working table which is caused by excessive suction.
8. Sufficient space has been left for replacing more powerful laser tube in future.
Replacing higher power laser tube is not restricted by machine shell any longer.

17. Advantage of D-series CO2 laser cutting engraving machine
9. Door lock of laser machine is upgraded to recoil-type lock, more beautiful and
convenient.
10. Upgrading he back cover where install the laser tube to an open design which
can open completely. It is more convenient to replace the laser tube.
11. Upgraded original inserted pin in the connection between front & rear cover and
machine shield to hinge-type. So that the switching is more comfortable, but
also eliminate the friction between machine cover and machine shield .
12. Running speed of the upgraded laser equipment has increased by 30%.
13. Upgrading mechanical transmission guide rail to roller linear guide rail , which
runs quieter and faster.

18. Advantage of D-series CO2 laser cutting engraving machine
14. The production technology of machine shell have been upgraded and improved,
so that the door can fit better with main body and other parts, it is easier for
dismantling.
15. Upgraded the technology of interface identifier. The original sticking labels has
been replaced by printed labels, more solid, and waterproof, long life, will not
fall off.
16. The upgraded exhaust fan is with small volume, low noise and strong power
17. Upgraded to two-stage ventilation pipe, the internal section has been installed in
our factory, users only need to install from the outside. It avoids the
inconvenience of installing pipe in original design.

19. Advantage of D-series CO2 laser cutting engraving machine
18. Mechanical structure has been upgraded and improved, more stable, making
operation more smoothly.
19. Installing shield to motion control card, it is dust-proof, anti-interference, and
anti-static.
20. Optimizing the up, down, left and right limitation protection way in four corners
ensure the equipment runs without collision, more reliable and safe.
21. Upgraded original three-axis motion control card to four-axis, so that the
material-feeding axis can co-exist with elevating axis together. It provides
expansion port to the multifunction of laser equipment.

20. Advantage of D-series CO2 laser cutting engraving machine
22. The upgrading of motion control card enhances parameter-read function. The
original one-way data write from computer to equipment has been upgraded to
two-way data write and read from computer and equipment. The data writing,
adjustment and management are more convenient.
23. Upgraded the electrical cooling device to built-in type, reducing the airborne
dust into the electrical cabinet. The equipment inner environment is cleaner.
24. Randomly presented a 2G USB flash disk, saving more abundant files.
25. Upgraded laser head, changed the air flow channel, and made airflow be more
concentrated and even.
26. Enhanced the communication ability between hand-held controller and laser
machine equipment. The users can operate the machine and modify parameters
by hand-held controller directly.

21. Advantage of D-series CO2 laser cutting engraving machine
27. Increased parameter categories, classified some parameters which doesn’t need
to adjust by users as manufacturers parameters, and manage them by password.
It simplifies the interface of parameter setting, and makes the users adjust
parameter more clear and simple.
28. Upgraded Frame mode. It contains Track frame, cut frame and dot corners.
29. Increased the function of modifying parameter in hand-held controller.
30. Increased the function of modifying speed and power online during the working
of equipment.
31. Increased the function of graphic layer simulation for engraved graphics. The
users can see the simulative effects after engraving visually.
32. Simplified the setting of cutting parameter, it is easier for users to set cutting
parameter.

22. Advantage of D-series CO2 laser cutting engraving machine
33. The compatible file format of upgraded software is more abundant. It supports
almost all two-dimensional graphical formats in the market.
34. Double laser head mode, which controls the power of two laser head separately
and effectively.
35. After installing the software in computer, it must connect to laser equipment
when you turn on the equipment for the first time. And it doesn’t need to
connect with equipment from next time. The software is very convenient to use.
36. Enhanced graphics function. It has increased Bezier curves and node editing
features, which is consistent with CORELDRAW.
37. Increased the function of graphic coordinates and graph size.

23. Advantage of D-series CO2 laser cutting engraving machine
38. It is more consistent with the embedding of CORELDRAW. It only needs
CORELDRAW t draw graphics, the parameter setting still complete in the
software. The operation is very convenient.
39. Supporting more advanced version of CORELDRAW and AUTOCAD. The
users will not be perplexed by choosing correct version of software no longer.

24. Sample Show

26. Wuhan GN Laser Equipment Manufacturing Co., Ltd.
Add: No.82, Jiahe Road, Hanyang District, Wuhan,
China
E-mail: gnlaser@188.com
Tel: +86-27-84530965, 84530966
Fax: +86-27-83600135
Http://www.gnlaser.com
Contact us