Epsilon Engineering is a civil engineering consulting firm that provides services including surveying, grading and drainage design, structural design, geotechnical analysis, construction material testing, and environmental assessments. It aims to be a full-service engineering provider through open communication and creative solutions. The firm's laboratories are certified to conduct various material tests for projects, including soil, concrete, asphalt, and aggregate testing to applicable ASTM standards.

1. E.E.M.Inc.

2. Who Are We?
• Epsilon Engineering is a professional engineering consulting firm
specializing in civil, Geo-technical, environmental, construction material
testing, and laboratory testing services.

3. Mission Statement/Philosophy
• Epsilon Engineering is a • Our philosophy of client advocacy
encourages open communication
professional engineering and sharing of creative solutions
consulting firm specializing to best assist our clients' specific
in civil, Geo- project needs. Our focus is to
apply appropriate technologies to
technical, environmental, co meet the challenges of the future
nstruction material with the promise to preserve
testing, and laboratory employing dedication, integrity
and ethical work practices to
testing services. each project. Trust and
Dependability are the
cornerstones of our business.

4. Civil Engineering Services
• Services Include:
• ALTA Surveys
• Topographic Surveys
• Boundary Surveys
• Underground Utility Surveys
• As-Built Surveys
• Construction Surveys
• Lot Splits
• Feasibility Assessments
• Grading & Drainage Design
• Grading & Drainage Reports
• Utility Layout & Design
• Site Plan Layout & Design
• Structural Design
• Landscape Design
• With the wide range of services we are able to provide, we can be and would love to be your
complete engineering provider.

5. Geotechnical Services
• Our Services Include:
• Site Investigations and feasibility studies
• Foundation and pavement design
• Settlement and subsidence analysis
• Shallow foundations and rigid mats
• Deep foundations
• Earth retaining structures
• Slope design, soil and rock stability
• Expansive/collapsing soils evaluation
• Borrow materials studies
• In-Situ Testing

6. Construction Material Testing
• Our construction services include:
• Aggregate evaluation
• Design, inspect, and test concrete mixtures
• Test bituminous materials
• Test and inspect soil compaction and stabilization
• Post-Tensioning Slab Inspection, Evaluation & Testing
• Quality welders and their procedures
• Special inspections on concrete, masonry & steel structures
• Project supervision and management
• Bolt Inspection
• E.I.F.S Inspection

7. Environmental Services.
• Phase I Environmental Site Assessments
• EEC provides site assessments for organizations and individuals
involved in property transactions to assess potential environmental
risks to the property and to retain protection from liability under
CERCLA. Environmental site assessments prepared by EEC meet or
exceed ASTM Standard of Practice E-1527, while providing the
necessary due diligence and disclosure required for property
transactions. Components of a Phase I may include:
• Review of Provided Information
• Records Review (Local and Federal)
• Physical Setting
• Historical Use Information
• Site Reconnaissance
• Interviews

8. Environmental Services..
• Phase II Environmental Site Assessments
• A Phase II ESA is undertaken if serious environmental concerns are
suspected following the Phase I ESA. The purpose is to identify the
limits and quantities of potentially hazardous materials; and to
evaluate the pathways whereby contaminants could reach
receptors. Components of a Phase II may include:
• Borehole drilling
• Air, soil, rock and groundwater sampling
• Selected materials (e.g. for asbestos, PCB's, CFCs, mercury, arsenic,
etc.
• Test pit excavation
• Chemical analysis of sampled materials
• Risk assessment
• Analysis, modeling and reporting

9. Environmental Services…
• Phase III Remedial Investigations
• A Phase III ESA is conducted when it becomes evident from prior
work that on-site contamination poses a threat to human health or
the environment. In this situation, contaminants occur at
concentrations above maximum acceptable limits, down-gradient
receptors are at risk, and site clean-up is required. A
recommendation is made as to the most cost-effective and
environmentally-appropriate remediation scheme. Components of
a Phase III may include:
• Removal of contaminated soil
• On-site or in-situ treatment of soil or groundwater
• A monitoring plan
• A decommissioning plan

10. Lab Certifications
• Our laboratories are both AMRL and CCRL certified and we are members
of the International Code Council (ICC) Member No. 5204348ICC. All of our
technicians are also ACI/ATI certified, and proud to offer the following
construction testing services:

11. Earthwork and Soils Testing
• Field density determination
• Density of undisturbed samples (ASTM D2937)
• Atterberg limits (ASTM D4318)
• Moisture-density relationship (ASTM D1557)
• Moisture content (ASTM D2216)
• Expansion/consolidation(ASTM D4546, D2435)
• Permeability testing (ASTM D5084, D2434)
• Percolation testing (ASTM D5084)
• Concrete/Masonry Testing
• Mix design/verification
• Compressive and flexural strength (ASTM C39)
• Time of set yield and temperature
• Coring (ASTM C42)
• Pre and post-tensioning inspection
• Slump, air content, unity weight, strength (ASTM C143, C231, C138, C39)

12. Aggregate Testing
• Unit weight of aggregate
• Liquid limit and plasticity index (ASTM D4318)
• Percent passing No. 200 (ASTM C117)
• Sieve Analysis (ASTM C136, C117)
• Specific gravity & absorption (ASTM D854, C127, C128)
• Fractured face count (ASTM A2212)

13. Asphalt Testing
• Asphaltic density tests (nuclear)
• Density/thickness of asphalt (ASTM C174)
• Strip test - Extraction and sieve analysis (ASTM D2171, C136, A2427)
• Index of retained strength
• Marshall density, stability and flow (ASTM D2726)

14. Concrete/Masonry Testing
• Mix design/verification
• Compressive and flexural strength (ASTM C39)
• Time of set yield and temperature
• Coring (ASTM C42)
• Pre and post-tensioning inspection
• Slump, air content, unity weight, strength (ASTM C143, C231, C138, C39)

15. Contact Epsilon Engineering
Epsilon Engineering & Material, LLC
13765 W. Auto Drive; Suite 119
Goodyear, Arizona 85338
Tel: 623-882-9928
Fax:623-882-9930
info@epsilonengineering.com