4. Setup from UNISERVICE 21.LTD 03/12/2009 Tigran Kasparov - 972 (0)504 373708 Igor Nazarov – 972 (0)544 51 2978 E-mail: [email_address] E-mail: [email_address] CHANGE ACTUATOR. 4. To remove actuator and down a landing payment. 5. To touch actuator. (See Chapter 4: Assembly the Acoustic Stack.)
5. Setup from UNISERVICE 21.LTD 03/12/2009 Tigran Kasparov - 972 (0)504 373708 Igor Nazarov – 972 (0)544 51 2978 E-mail: [email_address] E-mail: [email_address] Note: The effort on Manoskop key should be exposed according to the specified data in the working instruction
6. Setup from UNISERVICE 21.LTD 03/12/2009 Tigran Kasparov - 972 (0)504 373708 Igor Nazarov – 972 (0)544 51 2978 E-mail: [email_address] E-mail: [email_address] 6. To establish the down tool and actuator. 7. To fix a forward cover that actuator.
7. Setup from UNISERVICE 21.LTD 03/12/2009 Tigran Kasparov - 972 (0)504 373708 Igor Nazarov – 972 (0)544 51 2978 E-mail: [email_address] E-mail: [email_address] ADJUSTMENT ACTUATOR . 8. Turn off air pressure up to 0 (kPa). 9. Expose concerning centering pins, horn and the down tool or from to center them by means of a welded detail. 10. To fix a forward cover and the down tool. Note: The effort on Manoskop key should be exposed 20 (inc/lb).
8. Setup from UNISERVICE 21.LTD 03/12/2009 Tigran Kasparov - 972 (0)504 373708 Igor Nazarov – 972 (0)544 51 2978 E-mail: [email_address] E-mail: [email_address] 11. To expose mechanical stop screw. 11. To lift air pressure up to 100 (kPa) and after to on the feed. 12. Turn ON Power Supplier.
9. Setup from UNISERVICE 21.LTD 03/12/2009 Tigran Kasparov - 972 (0)504 373708 Igor Nazarov – 972 (0)544 51 2978 E-mail: [email_address] E-mail: [email_address] Installation of parallel between tools. 12. To lift air pressure up to 300 (kPa). 13. Turn off DOWN SPEED up to 20 (%). 14. To weaken fixing and adjusting bolts on a Base Mounting Centers.
10. Setup from UNISERVICE 21.LTD 03/12/2009 Tigran Kasparov - 972 (0)504 373708 Igor Nazarov – 972 (0)544 51 2978 E-mail: [email_address] E-mail: [email_address] 15. To put in the down tool a welded detail. 16. To press button HORN DOWN to lower Horn in a welded detail established in the down tool. Look the Chapter (Adjustment Leveling or in the instruction manual. Chapter 6.11 Using the Horn Down Feature). Press start switches. 17. To tighten adjusting and fixing bolts on a Base Mounting Centers.
11. Setup from UNISERVICE 21.LTD 03/12/2009 Tigran Kasparov - 972 (0)504 373708 Igor Nazarov – 972 (0)544 51 2978 E-mail: [email_address] E-mail: [email_address] 18. To press button HORN DOWN. 19 . To check and to expose operating conditions. GOOD LUCK!