Auto call setup for xcal series 3.x.xx voip

XCAL series
Guide for Auto Call
Setting for VoIP MOS
Test
Version 3.X.XX
2008-3-11

XCAL series AutoCall Setting VoIP MOS Test
Unit 206, 2/F., No. 8 Science Park West Avenue Page 2
Hong Kong Science Park, Shatin, Couei APAC Ltd
New Territories, Hong Kong www.couei.com
TEL: +852-2210-7004
1 VOIP MOS testing Condition
General Configuration of VoIP MOS testing(Skype)
1.1 Set Up VoIP MOS Server
1.1.1 Install Skype program on the PC(which is use as the VoIP MOS server.)
Skype Version should be above 3.6.0.248
(http://www.skype.com/intl/en/download/skype/windows/)
1.1.2 Set up a new account on Skype

TEL: +852-2210-7004
1.1.3 Set VOIP MOS Server Auto-reply In Skype

TEL: +852-2210-7004
Left Click
Left Click
Select the

TEL: +852-2210-7004
1.1.4 Set up Windows Media Player Auto-Cycle Play
1.2 The configuration of XCAL-W PC
1.2.1 Connect the jack of Mic and handset on the PC with the cable as below
（3.5mm two jacker(male) cable）

TEL: +852-2210-7004
1.2.2 Install the Skype soft ware and register the new account(same as above on server
side)
2 Start AutoCall Scenario Settings
Figure 1.1: AutoCall Scenario Settings window
Left Click

TEL: +852-2210-7004
Alias List
List of created scenarios (Call Scripts)
AutoCall Scenario
Scenarios selected among the Alias list to be used during the current auto call automation session.
3 Make a New VOIP Script (Create New Scenario)
Figure 2.1 : AutoCall Setup window for a new call script
(1) Designate VOIP Connection Information and Call Timers
Left click

TEL: +852-2210-7004
Figure 2.2 : Example of designate VOIP connection info and call timers
① Left click to select VOIP Script window
② Type any call script name
③ Designate VOIP connection
- IP Phone : Select Skype or Sj phone (Right now ,recommend use Skype )
- Call Type : Origination or Termination
- UDP Port: Fill the port No. which Skype used UDP port(it is important to the setting)
1
2
3
5
4

TEL: +852-2210-7004
User can get the UDP port No. as below：
- User ID: couei.apac (Receiver’s VOIP Account)
- Tick MOS Calculation (MOS testing or not)
- Sound Setting key (Default select Mono)
- Measurement Method
- Type:
1. General Configuration of VoIP MOS testing

TEL: +852-2210-7004
1） Both test side use XCAL-Ws
Below type is available:
Simplex(downlink)
Simplex(Uplink)
Half Duplex(downlink/ Uplink)
2） One side use XCAL-W, another side is ARS(Auto-response-system)
Simple ARS setup is as the above VoIP MOS server setting.
The condition support the test type:
ARS(Downlink)
ARS(Uplink)
- Algorithm (Default is choice PESQ MOS P.862-1)
- Time Sync terms(ms) (Default setting is 700 )
- Event (Whenever condition is attached, event will be logged)
- Tick MOS Count for traffic
set how many times MOS calculation will be test during the traffic time
- Bad Quality Threshold (set the Bad Quality value, score is 1-5)
- Continuous B.Q. Threshold (set the continue Bad Quality value, score is 1-5)
- Continuous B.Q. Threshold (set how many times Bad quality consider as continuous B.Q.
event)
- Continuous Call in B.Q.

TEL: +852-2210-7004
Whether or not continuous call in B.Q.
- File
- Original file (MOS testing sample file)
- Play file (During the test play which file)
- Play and wait time(ms) (During the testing, the interval between play the files)
Normally within 5000ms
- Wave save threshold
If the Quality score is below the value ,the file will be saved. Value:1-5
- Save path (Define the folder to save the logged wave files)
- Manual Rx Volume (Receive Volume from 0-32)
④ Designate Call Timers in unit of second
- Idle Time : 5 (seconds, Recommended value)
- Setup Time :30 (second, Air-interface setup time)
- T.Setup Time/Total time (seconds, grey , It is ignored)
- Traffic Time : 120 (seconds)
- Call Count : 100
Traffic Time and Call Count can be changed with your test propose.

TEL: +852-2210-7004
Please refer to VOIP Call Timers Diagram at next page.
⑤ Click OK to save the configuration
4 Call Timer
Idle Time
UE recess interval before start next Call
Setup Time
Timer for establishment of PPP connection (DUN)
T_Setup Time
Timer for logging to a target server (FTP, Ping, HTTP and so forth)
If Timer expires without successful access to the target Call, Traffic Setup Fail will be made in call
result.
Total Setup Time
Either “Setup time and Traffic Setup Time” or “Total Setup” time can be defined.
Traffic Time
Timer for downloading/uploading a file from/to VOIP server or opening target HTTP web site. If Timer
expires without completing downloading/uploading a file from/to VOIP server or opening HTTP web
site, Time Out will be made in call result.
In case of Ping Call, it is ignored.
Call Count
How many times Call test are performed
Total Time [ms]
Total time of a call, i.e. the UE will initiate a new call every Total time in ms, whatever call event has
happened within this time interval. This value has to be larger than the sum of Idle Time, Setup Time
and Traffic Time.
5 Schedule a Call Script

TEL: +852-2210-7004
Figure 4.1 : How to schedule a Call Script
① Left click and Drag & Drop Alias List item you want to test.
② Tick ‘All Scenarios’ to get a log file with your call test
③ Click ‘OK’ button to start a call test
6 The Security configuration in Skype
At the first time of run the Auto call(VoIP MOS testing),user should set some security setting with
Skype for XCAL-W
1.when XCAL-W auto-call link with Skype, the window below will jump
2.Click to set Manage API access control Skype
Left Click and
Drag & Drop
1
2
3

TEL: +852-2210-7004
After setting done, the XCAL-W can run the Skype automatically in next time.
7 VOIP Call Timers Diagram
Figure 5.2 : VOIP Call Timers Diagram

Auto call setup for xcal series 3.x.xx voip

Recommended

Recommended

More Related Content

What's hot

What's hot (20)

Viewers also liked

Viewers also liked (11)

Similar to Auto call setup for xcal series 3.x.xx voip

Similar to Auto call setup for xcal series 3.x.xx voip (20)

Recently uploaded

Recently uploaded (20)

Auto call setup for xcal series 3.x.xx voip