1. Curriculum vitae
Name: P.Paulpandy. Total Years of Experience: 23 Years.
Qualification: D.E.E.E., D.Ma.E.M. Post Applied: Elect. Engr. Comm. Or Maint.
Objective :
Committed to work sincere & dedication to enhance quality and safe work for company.
Seeking a better opportunity in electrical commissioning or operation & maintenance
department as back bone of organization growth.
My Profile :
I have excellent experience in commissioning, operation & maintenance in Oil, Gas, Power,
Petro Chemical & Gold Mine projects worked in JGC Gas project in Qatar, Saudi Aramco
world largest curd oil project in SaudiArabia, 2600 MW CCGT Power project GE& Hyundai
in Kuwait, 1600 MW CCGT Power project SIEMENS & DAEWOO in Abu Dhabi, UAE, world
largest petrochemical project in Al-Jubail, Saudi Arabia, Gold mine project in Al-Duwaihat,
Saudi Arabia and all type of industries. I can interact with other department like design,
material, Q/A & Q/C., planning & vendors to give best quality and to avoid delay & rework.
Working with PMC as well as Client till hand over the project.
My Strength :
Leadership quality, Fulfilling responsibility, Listening capacity, Specialty in priority work,
maintaining good relationship with people, Very well planning of work, Training the
people, Sincere and Dedicated working nature. I know many languages.
Work Experience Details:
M/S. MAADEN,
Period : From 25-03-2015 to 31-05-2015
Designation : Electrical Engineer-Commissioning.
Project : Maaden Gold Project, Al-Duwaihat, Saudi Arabia.
Work Done : Pre-commissioning, commissioning & energization of 13.8 KV
switchgears, 1.5, 2.5 and 3 MVA oil filled transformers, 4.16 KV neutral grounding resisters,
480 Volts. motor control centers, UPS, battery Chargers, power distribution panels, lightings
panels for main sub-station, 1200 crusher area sub-station, 2000 mill area sub-station,
3000 leach area sub-station, 4000 gold room sub-station, 5100 thickener area sub-station,
1

2. 5200 dewatering area sub-station, 7000 service one area sub-station and 7000 service two
area sub-station.
 Authorized energization engineer approved by client.
 Worked with PMC as well as Client till hand over the project.
 Preparing for the motor solo run test like continuity, insulation resistance test for the
power and control cables, insulation resistance and winding resistance test for the
motors.
 Functional test for the motors by local & remote operation. Relay & breakers
protection settings of all motors & non-motors feeders in MCC buckets.
 Functional and solo run test for the variable frequency drive motors.
 Protection testing and settings for all transformers and switchgears.
 Coordinating with vendors for commissioning the equipments.
 Trouble shooting to fix all type of faults and problems.
 Preparing test reports & checks sheets for all equipments for turn over package.
M/S. SADARA (Saudi Aramco & Dow)
Period : From 12-04-2014 to 12-03-2015.
Designation : Electrical Technician-Commissioning.
Project : World Largest Petro Chemical Complex.
Work Done : Pre-commissioning and testing of 13.8, 4.16 & 0.480 KV Switch
Gears, 80, 14, 3.75 MVA transformers, 75 KVA power & lighting Transformers, Protection
relay testing & setting. Observing construction activities in V2504, V2505, V2501, V2503
N&S, U4306 and SS465 sub-stations and plants in Chem 1 & 2 and plastic.
 Doing Hi-Pot test for MV & HV cables.
 Pre-commissioning done for motor control centre & cubicles.
 Functional test done MV & LV switch gears with auto transfer system.
 Insulation resistance & continuity test for cables, insulation resistance & winding
resistance test for motors for doing solo run test.
 Doing RFI’s.
 Preparing pre-commissioning tracking tools list.
 Witnessing all pre-commissioning and commissioning being a client.
M/S. Daewoo E&C and Siemens AG.,
Period : From 11-10-2012 to 31-10-2013.
Designation : Electrical Engineer-Commissioning.
2

3. Project : 1600 MW combined cycle gas turbine power project, S3, Suweighat,
Abu Dhabi - UAE.
Work Done : Commissioning of sea water intake motors, GT & STG building over head
cranes, Fuel gas compressor container, GT lube oil system, GT UPS, GT Generator Circuit
Breakers and 81, 82, 71&72.GT Air Intake System.
 Maintaining documents.
 Authorized energization engineer approved by client.
 Worked with PMC as well as client till hand over the project.
M/S. Hyundai Heavy Industries Ltd.,
Period : From 23-03-2010 to 01-05-2012.
Designation : Electrical Engineer-Commissioning.
Project : 2600 MW combined cycle gas turbine power project, Sabiya, Kuwait.
Work Done : Pre-commissioning and commissioning of transformers, switchgears, UPS,
Battery chargers, power distribution panels, mcc and lighting systems.
 Doing hi-pot test for MV & HV cables.
 Preparing and ding solo run tests for motors.
 Functional test & protection relay setting in motor cubicles.
 Preparing test reports & checks sheet for turn over package.
 Maintaining documents.
 Worked with PMC as well as till hand over the project.
M/S. Saudi Arabia Kentz Co Ltd,
Period : From 18-03-2008 to 05-09-2009.
Designation : Electrical Supervisor- Commissioning.
Project : World largest curd oil project, Saudi Aramco, Saudi Arabia.
Work Done : Pre-commissioning of transformers, switchgears, UPS, battery chargers,
mcc’s, lighting transformers.
 Doing hi-pot test for MV & HV cables.
 Doing functional test for mcc motor & non-motor feeders.
 Preparing & doing for motors solo run test.
 Pre-commissioning & energization for indoor & outdoor lighting circuits.
 Maintaining documents.
3

4.  Worked with PMC as well as till hand over the project.
M/S. Kentz W.L.L. Qatar.
Period : From 25-05-2006 to 15-02-2007.
Designation : Electrical Supervisor-Commissioning.
Project : Gas Project, Japan Gas Corporation, Qatar.
Work Done : Pre-commissioning of transformers, switchgears, mcc’s, power & lighting
panels. Continuity & Insulation resistance test done for power & control cables. Doing hi-pot
test for MV & HV cables. Preparing and doing solo run test for motors.
M/S. Bahavan Engineering Company LLC, Rubi, Muscut, Oman.
Period : From 03-05-2005 to 10-05-2006.
Designation : Supervisor-Maintenance..
Responsibility : Site In-charge of Electrical & Mechanical maintenance.
Work Done : Operation and Maintenance of 11 KV/ 440 Volts transformer 80
Nos. , OHT cranes 8 Nos. , Compressors, Ship lifting equipments, Switch Gears.
Additional Work: Preparing scope of work, costing, executing worth 70000
Riyals of Oman Navel Base additional work.
M/S.Automotive Coaches and Components Ltd., Gummudipoondi, Tamil Nadu.
(Joint Venture of M/S. Ashok Leyland and TIDCO)
Period : From 15-11-1999 to 01-05-2005.
Designation : Executive Maintenance.
Responsibility : Head of Electrical and Mechanical maintenance, commissioning
& installation Dept. (Reporting to General Manger. Mfg.)
Work Done : Operation and Maintenance of 11 KV/ 433 Volts. sub-station,
O.C.B's, 750 KVA transformer, MV Panels, Automatic Capacitor Panel, 380 KVA, generators
with Synchronous Panel, S.S.B's, 30 HP reciprocating compressor, 50 HP Kirlosker
reciprocating compressor, 40 & 60 HP. Atlas cop-co screw compressor, Paint booth ovens,
exhaust fan and blowers etc.
 Maintenance of 7.5 ton gantry cranes, 2 ton OHT cranes, 400 & 250 amps. CO2 mig
welding m/c's, 400 amps. arc welding m/c's, 8mm,7mm and 4mm shearing m/c's,
lathe, milling, radial drilling m/c's, fork lift's, escort cranes etc.
 Doing predictive and preventive maintenance.
 Preparing preventive maintenance schedule by analyzing break down and m/c's
history.
4

5.  Reducing down time and cost of m/c's by doing continuous improvement through
proper route cause.
 Full filling company statutory requirements like compressors, receiver, fork lift, OHT
cranes, chain pulley block, paint booth, paint booth exhaust fans, and other safety
equipments.
 Full filling I.E. Rule 63, 46, inspection, getting drawing approval and safety
certificate.
 Identification of electrical & mechanical spares & coordination with purchase
department to procure correct and quality materials.
 I was the main ISO audite to maintain ISO 9001-2000 standard.
Achievements:
 I got third prize for reducing power consumption and maximum demand by
improving power factor from .9 to .99.
Project Work:
 Installation of panels, cable trays, glanding, termination & equipments connected
loads 150 KVA. Commissioning, conducting inspection & getting drawing approval
and Electricity Board safety certificates.
 Installation & commissioning of connected loads 250 KVA equipments like,
11KV/4OO amps O.C.B's, MV panels, M.C.C, automatic power factor controller,
glanding & terminations. Getting drawing approval and safety certificate.
 Re-installation and re-commissioning of existing m/c's from one area to another
area. Rearrangement of electrical connected loads drawing approval and safety
certificate.
M/S. Norton Group, Gummidipoondi, Tamil Nadu.
5

6. Period : From 24-11-1997 to 25-10-1999
Designation : Engineer Maintenance.
Responsibility: In-charge of Electrical and Mechanical maintenance, commissioning
&installation department reporting to Works Manager.
Work Done :
 Northern Electrical: Maintenance of 250 KVA generators, 10 HP compressor, wire
drawing m/c’s and tubular m/c's.
 Klassic Polymers: Maintenance of 62.5 KVA generator, 5 HP compressor,
power looms, winding m/c's, extruders & LV switch gears.
 Norton Polymers: Maintenance of 160 KVA generator, 10 compressor,
power looms, winding m/c's, extruders & LV switch gears.
 Southern Latex Ltd.: Maintenance 125 KVA generator, 20 HP compressor,
hydraulic press, motors & LV switch gears etc.
 Installation & commissioning of 1000 KVA diesel generator with automatic control
panel.
 Trouble shooting to fix all type of faults & problems.
M/S. SIBAR Autoparts Ltd., Tirupathi, Andhra Pradesh.
Period : From 29-03-1995 to 21-11-1997
Designation : Engineer Maintenance.
Responsibility : In-charge of Electrical and Mechanical maintenance, commissioning
&installation department. (Reporting to Works Manager)
Work Done :
6

7.  Sub-Station: Operation & Maintenance of 500 KVA transformers, MV panels, 300
KVA generators, capacitor banks, LT switchgears.
 Machine Shop: Maintenance of hydraulic honing m/c's., special purpose
m/c's., lathes, drilling m/c’s.
 Heat Treatment Plant: Maintenance of 60 KW pit type furnaces, 30 KW
muffle furnaces, 36 KW degreasing plant.
 Plating Section: Maintenance of 100 amps. Auto transformers, 4000 amps.
rectifiers, 2 ton cranes, special purpose acid centrifugal pumps, 3000 watts lead
immersion heaters, remote control operated panels.
 Foundry : Maintenance of bale out furnaces, tilting furnaces, electrical
holding furnaces capacity 24 KW, 25 HP Elgi screw type & 25 HP Atlas cop co
compressors, PLC operated core shooting m/c's., 125 KVA & 62.5 KVA generators.
Achievement:
 I got award for reducing maintenance cost in plating section.
Project Work :
 Installation and commissioning of H.T. structure, 500 KVA transformer, M.V. panels,
SSB's, LDB'S, DB's, Installation of cable trays, cables, glanding & termination of 490
KVA connected load.
 Installation and commissioning of 300 KVA generators.
 Installation and commissioning of Pit type and Muffle type heat treatment furnaces.
 Installation and commissioning of hard chrome plating section equipments like Step
down auto transformers, 4000 amps. DC rectifiers and control panels.
 Installation and commissioning of m/c. like lathe, milling, hydraulic honing, and
screw type compressors.
M/S. Kowtha Steel Products, Vijayawada, Andhra Pradesh.
7

8. Period : From 01-07-1992 to 26-03-1995.
Designation : Engineer Maintenance.
Responsibility : Maintenance of Electrical and Mechanical department.
(Reporting to GM Foundry)
Work Done : Operation and Maintenance of Induction Furnaces, 11 KV Sub-
station, 150 KVA, 250 KVA, 500 KVA transformers, OCB's, MV panels, LV panels, 2 & 5 ton
OHT cranes, 100 KW heat treatment furnaces, Shot blasting m/c's.
 Trouble shooting to fix all type of faults & problems.
 Found the route cause to fix the main contactor of induction furnace fault & frequent
break down of furnace.
 Changed the old model contactor to new model contactor to solve the major problem
permanently.
M/S. Tamil Nadu Electricity Board, Chennai , Tamil Nadu.
Period : From 15-05-1991 to 19-06-1990.
Designation : Trainee (Electrical Engineer)
Work Done : Repairing, Testing and Maintenance of transformers from 63
KVA to 2000 KVA, OCB's, PT's, CT's. Calibration and testing of energy meters and trivector
meters. Operation and Maintenance of 110/11 KV sub- station.
Date of Birth : 30-04-1970.
Marital Status : Married.
Address : # 2, Srivenkateshwara Illam, Muthusamy Servai Street,
B.K.Pudhur, Kuniyamuthur, Coimbatore, Tamil Nadu, India.
Post Box #: 641008
Pass Port Details : Pass Port #: J5549606, Date of Issue : 14-06-2011.
Place of issue: Kuwait, Date of Expiry: 13-06-2021.
"C" License Details : " C " License # 16765, Valid Till: 2016. (Government electrical
license to work in live equipment)
Language Known : English, Hindi, Tamil, Telugu, Kannada, & Malayalam.
Contact Mobile # : In KSA +966 538573306, +966 564996890
In India +91 9952162247, +91 9500377352
E-Mail ID : paulpandy6666@gmail.com
Srinarayana9999@gmail.com
Educational Qualification:
Exam Passed Name of Institution /
University
Year of
Passed
% Of Marks
Diploma in Electrical & V.S.V.N. Polytechnic, April, 1989. 69.4%
8

9. Electronics Engineering. Virudhunagar.
Diploma in Maintenance
Engineering and
Management.
Annamalai University,
Chidambaram.
May, 2004. 56.5%
Declaration:
I hereby declared that the above information’s are true and correct to the best
of my knowledge.
Place: Coimbatore. Yours Faith Fully,
Date : 17-06-2015. P.Paulpandy.
9

10. Electronics Engineering. Virudhunagar.
Diploma in Maintenance
Engineering and
Management.
Annamalai University,
Chidambaram.
May, 2004. 56.5%
Declaration:
I hereby declared that the above information’s are true and correct to the best
of my knowledge.
Place: Coimbatore. Yours Faith Fully,
Date : 17-06-2015. P.Paulpandy.
9