http://partcatalogs.net - agri parts catalogs, truck parts catalogs and more

1. A note to our customers, parts managers and dealers:
This manual has been prepared to assist you in the proper use, daily care, and operation of
your new Krause equipment. It contains specific information on the many built--in features
of your equipment, the accessories and options that are available, general specifications, and
instructions for making minor adjustments.
Read this manual carefully before operating your Krause equipment, and keep it in a
convenient location for later reference.
In order to ensure that you have the most current operation manual available for your
implement, we have added a revision code to each manual. Please note the information
listed below and specify when placing service calls or ordering parts.
Manual for Model: 4830
This manual covers models beginning with Serial No. 1001
Operation Manual #: 4830--1
Parts Manual #: 4830--2
ISSUED TO: ISSUED BY:
Owner’s Name Krause Dealer
Mailing Address City
City State
State Date of Purchase
Printed APR11 SN 1631

3. Warranty Policy
(Krause Serial Numbered Wholegoods purchased subsequent to May 1, 2008)
Note: This warranty is limited to the equipment and parts sold in North America and all
warranty work must be accomplished by a Krause Corporation Authorized Service
Center rated to perform maintenance on Krause Corporation Products.
A. KRAUSE CORPORATION (“KRAUSE”) LIMITED WARRANTY.
(1) Subject to the limitations and conditions hereinafter set forth, Krause warrants, at the time of delivery
by Krause to be free from (i) defects in materials or workmanship, and (ii) defects in design that in the
view of the state of the art as of the date of manufacture should have been foreseen provided, however,
that the defect must be discovered and reported to Krause within the periods specified as follows. For
a period of one year all new serial numbered production agricultural units covered by this warranty;
for a period of thirty--six (36) months the tongue weldment, center frame weldment, wing frame
weldments, disc harrow gang bearings and K--Tine field cultivator shanks.
(2) Krause does not warrant disc blades, shanks, hydraulic cylinders, accessories and other parts not
manufactured by it, but supplied with or as a part of its products. Krause will, however, obtain and
pass on any adjustments provided by the manufacturers of such parts under these manufacturer’s
warranties. Tires supplied on Krause products, will be warranted by the tire manufacturer’s retail
outlets.
(3) The entire extent of Krause’s liability shall be limited to that of either reimbursing Buyer for its costs
of purchasing a rebuilt, over--hauled or repaired part from either Krause or a proper Krause
Authorized Service Center or, at Krause’s election, reimbursing buyer for its costs of having the part
repaired at a proper Krause Authorized Service Center. If Krause elects not to repair the part and if
neither a rebuilt, over--hauled or repaired part is, in Krause’s opinion, timely available then Krause
will reimburse buyer for its costs of purchasing a new part from either Krause or a proper Krause
Authorized Service Center. The labor necessary to remove from the product such part or parts and to
install in the product such part or parts, as well as any repair made as the result of improper
installations by Krause, shall be covered by this warranty, provided the work is performed at a proper
Krause Authorized Service Center.K If return of the defective part is required, it must be returned
shipping prepaid to Krause. Krause’s limited warranty will apply to any part repaired or replaced by
a proper Krause Authorized Service Center pursuant to Krause’s Limited Warranty: however, the
applicable warranty for such part repaired or replaced shall be limited to the unexpired portion of
Krause’s Limited Warranty described in paragraph (1) or (2) above, as applicable. In other words, the
warranty period of the part repaired or replaced does not start over from the date of reinstallation.
K[Krause Corporation will repair or replace, free of charge, any part of the product found to be defective,
within the specified warranty periods, after an inspection of the part has deemed it to be defective.
Inspection must be performed by an authorized agent of Krause Corporation, or returned to the Krause
factory for inspection and disposition. Warranty labor will be considered during the first year of
warranty only. Krause Corporation will establish and publish an hourly flat rate for shop labor and
reimbursement during the first year of the warranty period. Krause Corporation does not allow credit
for the cost of travel time, mileage or hauling as a warranty allowance. During the remaining second
and third year, when applicable, Krause will repair or replace the defective part, without consideration
of labor charges.]
(4) Routine services (such as inspections, field settings, adjustments, etc.) and replacement of items which
deteriorate from expected normal wear and tear or exposure (such as paint, tires, hoses, blades,
sweeps, etc.) are not covered by this Limited Warranty. Such routine services and replacements
required during the course of operation are not considered to be the result of any defect in the product.

4. B. LIMITATIONS APPLICABLE TO KRAUSE’S LIMITED WARRANTY.
(1) This Warranty Policy only applies to equipment and parts sold in North America. Krause will be
relieved of all obligations and liability under this warranty if:
(i) The alleged defect in the part is due to misuse or neglect on the part of someone other than Krause;
or
(ii) Krause’s identification mark or name or serial number has been removed from the part in question;
or
(iii) The product and/or equipment have not been maintained, operated or stored either in accordance
with applicable manuals, communications or other written instructions of Krause or any
manufacturer of the part involved, or in accordance with applicable regulations and advisory
circulars unless buyer shows that such maintenance, operation or storage was not a contributory
cause of the defect; or
(iv) The part in question has been modified or altered after delivery other than by the manufacturer
or in accordance with a modification or alternation scheme approved in writing by the
manufacturer; or
(v) The product is used for purposes other than conventional owner/operator usage. Usage not
considered conventional owner/operator includes, but is not limited to, operation conditions that
consist of rocks or other obstructions.
(2) For the purpose of this Warranty, no part of the product or equipment will be regarded as breaching
the limited warranty merely because, subsequent to its delivery, some modification or alteration
becomes necessary for product improvements or in order to meet a change in the requirements of any
applicable regulation.
(3) TO THE EXTENT ALLOWED BY APPLICABLE LAW, BUYER WAIVES AS TO KRAUSE ALL
OTHER WARRANTIES, WHETHER OF MERCHANTABILITY, FITNESS OR OTHERWISE, THERE
ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACT HEREOF.
(4) TO THE EXTENT ALLOWED BY APPLICABLE LAW, THE OBLIGATIONS OF KRAUSE SET
FORTH HEREIN SHALL BE THE EXCLUSIVE REMEDIES FOR ANY BREACH OF WARRANTY
HEREUNDER, AND, TO THE SAME EXTENT, KRAUSE SHALL NOT BE LIABLE FOR ANY
GENERAL, CONSEQUENTIAL OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT
LIMITATION, ANY DAMAGES FOR DIMINUTION OF MARKET VALUE, LOSS OF USE OR LOSS
OF PROFITS, OR ANY DAMAGES TO THE PRODUCT CLAIMED BY BUYER OR ANY OTHER
PERSON OR ENTITY UPON THE THEORIES OF NEGLIGENCE OR STRICT LIABILITY IN TORT.
(5) ANY ACTION BY BUYER FOR BREACH OF THIS WARRANTY BY EITHER KRAUSE OR SELLER
MUST BE COMMENCED WITHIN (1) YEAR AFTER THE CAUSE OF ACTION ACCRUES.

6. Establishing Customer Warranty
Customer’s Obligation
1. The customer is responsible for reading the operation manual supplied with each serial
numbered unit. The manual describes the safe and correct operating procedures of the specific
product. The operation manual will also instruct the user on recommended lubrication and
maintenance of the product.
2. The customer will advise the dealer of the anticipated start date of the product so a dealer
representative can be on hand to make necessary field adjustments.
3. The owner is also responsible for inspecting the product during and after use. If a part has failed
or is in need of repair, it should be replaced. When continued use of the product would result in
excessive wear of other components, the part should be replaced before operation is continued.
Continued use of the product may void warranty on other parts damaged from this condition.
The user must make the machine available to the dealer for a warranty repair.
4. It is the customer’s responsibility to deliver his machine to an authorized Krause dealer for
completion of a warranty repair. If the dealer agrees to make a service trip to the customer’s
residence, it is an agreement between the dealer and the customer. Krause will not allow
warranty credit for the cost of travel, mileage, or hauling.
5. Warranty labor consideration will only be given during the first year of warranty. Any labor
charge for the 2nd or 3rd year on the limited warranty will be at the customer’s expense.
This warranty gives you specific rights, and you may also have other rights which vary from state to state.

7. 1
4830 IN--LINE RIPPER
DEALER PREDELIVERY CHECK SHEET
TO BE CHECKED BY DEALER
CUSTOMER DATE
ADDRESS
DEALER
ADDRESS
MODEL SERIAL NUMBER
DEALER CHECK:
All Units:
1. Check to see that all bolts are tight and pins are in place.
2. All safety decals are in place and easily visible.
3. Customer review sheet is filled out and signed.
4. Review lighting requirements. Light kits are standard.
5. Check to see that the Operation Manual is in the storage canister on the implement.
6. Make sure that the SMV emblem and lights are clean and in place.
7. Check lights for proper operation.
Folding Units:
8. Check to see that hydraulic cylinders are full of oil (air bled out of cylinders). Clevis pins
with hair pin clips should be in place. Hydraulic system requires 8 Quarts of oil.
9. Examine hydraulic hoses to see that they are protected from damage.
10. Make sure wing hinges and wing lift parts are properly secured.
11. Restrictors should be installed in wing lift cylinder ports.
Optional Pull Hitch:
12. Check to see that hydraulic cylinders are full of oil (air bled out of cylinders). Clevis pins
with hair pin clips should be in place. This option requires 6 Quarts of oil.
13. Examine hydraulic hoses to see that they are protected from damage.
14. Check lug bolts holding wheels to the hub to see that they are torqued to 120 Ft. Lbs.
15. The correct size tires, 11L x 15, 8--Ply inflated to 36 PSI pressure should be on the
implement.
16. Check to see that bolts attaching clevis to the hitch are tightened.
17. Jack should be operational for support of tongue when implement is not attached to a
tractor.
18. Safety Chain is in place.
DELIVERED BY
DATE

15. O1
SAFETY FIRST
WATCH FOR THIS SYMBOL AND CAREFULLY READ THE MESSAGE.
1. Read and understand the operation manual before operating the machine.
2. Be sure safety decals and reflectors are clean and in place.
3. Do not climb or walk on frames.
4. Never position yourself under any portion of the implement unless the entire unit is lowered to the
ground.
5. Stop engine and set parking brake before leaving the operator’s position to adjust, lubricate, clean or
unclog the machine.
6. Do not stand between the implement and the tractor unless the tractor brakes are locked and the engine
is shut off.
7. Never operate unit until hydraulic cylinders and lines are full of oil and free of air.
8. Use a Slow--Moving--Vehicle (SMV) emblem and lights when transporting.
9. Do not transport an implement over 25 miles per hour on the best surface conditions. Reduce speed
when going up or down hills or when approaching ditches or corners.
10. Make sure there is sufficient ballast on the front of the tractor for safe operation. See ”Preparing Tractor
For Operation”.
11. Make sure the gauge wheels are assembled correctly to prevent possible interference with tractor cab
or fenders.
12. Machinery should be operated only by qualified persons familiar to the tractor and equipment, and the
safety related items.
13. Keep everyone clear while operating hydraulics or controls and also when machine is in motion.
14. Never permit riders on implement or tractor.
15. Lower parking stand before unhooking.
16. NEVER disassemble the spring reset spring assembly. The springs are under compression and have
potentially dangerous stored energy. Disassembly could result in severe personal injury or death.
17. Spring reset mechanisms operate quickly and forcefully. Use extreme caution when attempting to
dislodge an obstruction.
18. Be sure safety signs are clean and readable. All safety related signs must be replaced if the implement
is painted or the decals are otherwise rendered unreadable.
Elimination of the hazards listed above should not be construed as providing guarantees that the
equipment will meet or exceed all standards or regulations or will be completely safe to all personnel.
The operator should inspect and review the implement after it is in his possession for adequacy in safety
for the function for which it will be used.

16. O2
OPERATING INSTRUCTIONS
Elimination of the hazards listed in this manual should not be construed as providing guarantees that the
equipment will meet or exceed all standards or regulations, or will be completely safe to all personnel.
The operator should inspect and review the implement after it is in his possession.
READ ALL THE SAFETY DECALS ON THE IMPLEMENT AND REVIEW THE
SAFETY FIRST SUGGESTIONS ON THE BACK OF THIS MANUAL TO
REFRESH YOUR MEMORY. WATCH FOR THE SAFETY SYMBOL, AND READ
THE INFORMATION. THIS IS FOR YOUR OWN PROTECTION.
ABOUT YOUR IN--LINE RIPPER
This implement was designed for deep fallow tillage or stubble--mulch tillage with very little residue
disturbance. Your ripper will operate over a wide range of speeds, ranging from 4 to 6 miles per hour.
Exercise caution in rocky or extremely hard conditions. If rocky conditions exist in your fields, operate at
a slow speed and equip your ripper with spring shanks.
Horsepower requirements generally will range from 25 to 35 HP per shank (do not exceed 40 HP per
shank).
YOUR RIPPER CAN BE EQUIPPED WITH EITHER A POINT AND LOW DISTURBANCE SHANK
CAP OR A POINT AND 5” SHATTERING WING. THE LOW DISTURBANCE SHANK CAP OFFERS
THE NARROW PROFILE NEEDED FOR INTER--ROW RIPPING. THE 5” SHATTERING WING WILL
OFFER MAXIMUM SUBSOIL FRACTURING BETWEEN SHANKS IN THE COMPACTED ZONE,
WHILE MINIMIZING DISTURBANCE OF SURFACE RESIDUE.
TILLAGE DEPTH
As a general rule you should adjust the depth to about one--half inch below the compacted zone. This is
normally 7 to 10 inches and very rarely more than 11 inches. Below the compacted zone is soil in its
natural virgin state and should not be disturbed. The best fracturing of the zone occurs with the point
positioned just below it.
PREPARING THE RIPPER FOR OPERATION
1. Inspect all hardware on the ripper. Make sure nuts and bolts have been tightened properly. See the
recommended torque values on back side of colored Assembly Section divider page in this manual.
If bolts show signs of wear replace them with the same SAE grade bolt.
2. Before attaching the ripper to tractor, be sure that the hitch pins and spacers are completely assembled
to match the tractor.
3. Make sure that all grease zerk locations have been sufficiently greased. USE EXTREME CAUTION
WHEN WORKING AROUND SHARP SUBSOIL POINTS, AND COULTER BLADES.
4. Check and adjust tightness of wheel bearings and wheel bolts before operation, after the first week,
and periodically thereafter.
5. Adjust inflation pressure of tires: 11L x 15 8--ply tires to 36 PSI, and
20.5 X 8--10 gauge wheel tires to 90 PSI.
PREPARING THE TRACTOR FOR OPERATION
Read your tractor owner’s manual. It will describe safe methods of operation. Make sure your tractor
has proper added ballast, and that its hydraulic system is full of oil and working properly. Check tractor
brakes and warning lights, and make sure that they are in working order.

18. O4
OPTIONAL PULL HITCH
For tractors without three--point hitches, your 4830 In--Line Ripper can be equipped with an optional pull
hitch. This allows your unit to be attached to your tractor drawbar.
Warning: The tongue may raise rapidly when unhitching. Lower unit to the
ground before unhitching. Failure to heed this warning may result
in serious injury or death.
Hitching and Unhitching
Warning: Do not allow any person to stand between the tractor and
implement while backing into position. Sudden loss of control
could cause serious injury or death to a person caught between the
tractor and implement. Tell your helper to wait until you give him
the signal that the tractor is in park or neutral and the brake is set
and the engine is shut off.
Hitching to the tractor:
1. The ripper should be lowered to the ground with the weight on the shanks and the tongue should
be supported by the jack.
2. Unpin the tractor drawbar so it can be moved from side--to--side.
3. A clevis support pin is provided to support the hitch clevis in a horizontal position while hitching
to the unit.
4. Back the tractor to the ripper hitch.
5. Attach the clevis to tractor drawbar with a clevis pin that fits the hole size in the tractor drawbar.
Make sure the clevis pin is locked or bolted in place to prevent loss.
6. Fasten the safety chain to the tractor.
7. Remove small clevis support pin and place in storage position in hole in the plate on top of the
hitch. Place the tongue jack in its storage location on top of the tongue.
8. Connect the hydraulic hoses and light plug. NOTE: The hose(s) with the red grip(s) is the
raise/lower hose.
Unhitching from the tractor:
If the ripper is not to be used for the remainder of the day, select a good parking place that will permit
the lowering of the ripper to the ground.
1. To unhitch the tractor from the ripper, place the tractor in park or neutral and set the brake.
2. Have all personnel stand clear and lower the unit to the ground so that the weight of the unit is
resting on the shanks.
3. Turn off tractor power and relieve any hydraulic pressure that might be in the system by moving
the tractor control lever(s) back and forth.
4. Remove the tongue jack from its storage location and raise the tongue height until the clevis
pin can be removed.
5. Disconnect the hydraulic hoses and light plug; the tractor may be moved away.

49. P23
HYDRAULICS -- FOLDING FRAME & PULL HITCH
FOR MODELS -- ALL FOLDING APR11
Item Part Number Part Description Qty.
1 21--171 4 x 16 Hydraulic Cylinder 2
2 4956--75--0 Restrictor Assembly w/ Tag 4
3 24--201R 3/8 x 30” Black 2W JIC Hydraulic Hose -- 132” Folding Frame 2
24--256R 3/8 x 48” Black 2W JIC Hydraulic Hose -- 168” Folding Frame 2
4 24--292R 3/8 x 50” Black 2W JIC Hydraulic Hose -- 132” Folding Frame 2
24--209R 3/8 x 68” Black 2W JIC Hydraulic Hose -- 168” Folding Frame 2
5 25--126 Panduit Strap 12
6 25--373 3/4(F) JIC Swivel -- 3/4(M) JIC Branch Tee 2
7 25--304 3/4 -- 3/4 JIC Coupler 2
8 24--228R 3/8 x 150” Black 2W JIC Hydraulic Hose 2
9 25--1153 5/8” Hose Clamp 8
10 62--491 3/8NF x 3/4” Cap Screw 4
11 2145--170--3 Hose Stand 1
12 62--300 1/2NC x 1” GD5 Cap Screw 1
13 64--108 1/2” STD. Flat Washer 1
14 64--107 1/2” STD. Lock Washer 1
15 63--106 1/2NC Hex Nut 1
16 2145--170--5 Hose Plate 1
17 2426--170--5 Hose Clamp 1
18 62--343 1/2NC x 2” GD5 Cap Screw 1
19 63--107 1/2NC Lock Nut 1
20 4830--92--0 3/8 x 58” (Yellow/Yellow Grip) Hose Assembly -- (See
Hydraulic Hose w/ Plastic Grip on page P24
1
21 4830--91--0 3/8 x 58” (Red/Yellow Plastic Grip) Hose Assembly --
(See Hydraulic Hose w/ Plastic Grip on page P24
1
22 4830--93--0 3/8” x 80” (Red/Black Plastic Handle) Hose Assembly --
(See Hydraulic Hose w/ Plastic Grip on page P24
1
23 4938--94--0 3/8” x 80” (Black/Black Plastic Handle) Hose Assembly --
(See Hydraulic Hose w/ Plastic Grip on page P24
1
24 24--299R 3/8 x 162” Black 2W JIC Hydraulic Hose 1
25 24--2101R 3/8 x 186” Black 2W JIC Hydraulic Hose 1
26 24--225R 3/8 x 140” Black 2W JIC Hydraulic Hose 1
27 21--1008 4--1/4 x 10 Hydraulic Cylinder 1
28 21--1007 4 x 10 Hydraulic Cylinder 1
29 25--301 O--Ring 37_ Flare 90_ Hydraulic Fitting 4
30 5800--17--0 Lock Assembly 2
31 6124--17--1 Lock 1
32 44--107 Threaded Bumper 2
33 63--102 3/8NC Hex Nut 2
34 60--103 5/16” DIA. P.T.O. Pin 1
35 74--387 Maintenance Lock Decal 1
36 25--314 O--Ring 37_(F) Flare Hydraulic Fitting 1
37 25--2272 Check Valve Manual Release 1
38 25--300 O--Ring 37_(M) Flare Hydraulic Fitting 1
39 74--574 Decal, Transport Lock Wheel 1
40 21--200 Stroke Control Kit (Includes Items 41,42,43,44,45) 2
41 21--318 1” Depth Stop Collar 2/kit
42 21--319 1--1/4” Depth Stop Collar 1/kit
43 21--320 1--1/2” Depth Stop Collar 1/kit
44 21--876 1--3/4” Depth Stop Collar 1/kit
45 21--321 Clip 5/kit

63. A5
PULL HITCH ASSEMBLY
Refer to the parts section pages P7 to P9 for assembly illustrations of pull hitch and lift wheel assembly.
Assemble as shown.
Lift Wheel Mount Locations
1. The Lift Wheel Mount assembles to the front of the center frame with the wheels in front of the unit.
Counting from the centerline of the unit:
On all 5, 7 & 9 Shank Models, as well as 4 Shank 40”, 6 Shank 30” & 8 Shank 36” Models, place the
lift wheel between the 2nd and 3rd coulters (the center coulter is number 1 on odd shank units). On
all other 6 and 8 Shank Models, place the lift wheel between the 1st and 2nd coulter from centerline.
2. HYDRAULICS -- --
Warning: Use only hydraulic hose that meets or exceeds 3,000 psi
working pressure. Serious injury or death may occur if a
hose ruptures.
Warning: Do not pin the lift cylinder in place until all hydraulic
assembly is complete and system has been purged of air
and filled with oil. Serious injury or death may occur due to
unit lowering.
Place the lift cylinders on the center frame near where they are to be pinned with the rod ends above
the base end. Be sure rod can extend without any interference.
Note: No tape or sealant is necessary on O--Ring / 37_ Flare Fittings.
Note: The larger 4--1/4” Diameter cylinder is placed on the left hand lift wheel.
Refer to the parts section page P20 to P23 for the correct assembly of hoses, fittings, and hose
clamps.
After all connections have been made and tightened, hook the hoses to a tractor and cycle the lift
cylinders until the cylinders respond with immediate solid actuation. When the cylinders reach full
extension, hold the tractor lever engaged to let the oil bypass the 4--1/4” series cylinder and go on to
the 4” series cylinder and then back to the tractor. If you do not hold the lever, the air between the
cylinders will not be purged and the system will not function properly.
Warning: Escaping fluid under pressure can penetrate the skin causing serious injury
or death. Avoid the hazard by relieving pressure before disconnecting
hydraulic lines. Tighten all connections before applying pressure.
Search for leaks with a piece of cardboard. Protect hands and body from
high pressure fluids.
If an accident occurs, see a doctor immediately. Any fluid injected into the
skin must be surgically removed within a few hours or gangrene may
result.
3. After the cylinders have been purged of air, pin them to the wheel lift assemblies.
Warning: The unit is considerably tail heavy with the pull hitch. The tongue will raise
rapidly when raising the unit if it is not hitched to a tractor. Serious injury
or death may occur. See the instructions for Hitching and Unhitching the
unit in the Operating Section of this manual.

64. A6
SHANK STAGGER KIT
STAGGER KIT PLACEMENT: Model 530R ---- Start with first shank right or left of center.
Model 730R ---- Start with center shank.
Model 730F ---- Start with first shank right or left of center.
Model 930F ---- Start with center shank.
Caution: Ripper shank assemblies can weigh as much as 400 lbs. Use suitable
lifting equipment when removing assemblies. Failure to do so could
cause serious injury.
Remove the ripper shank assembly from frame and attach the stagger weldment to the rear of the frame
using a bolt plate and (4) each 1NC x 9” Machine Bolts, Lock Washers and Hex Nuts. Torque the 1”
Hardware to 625 ft. lbs. Check to be sure that the stagger weldment clamps over the frame box and that
the plate is tight down against the frame. Assemble the ripper shank assembly to the stagger weldment.
Note: On the Pathfind’rt swing shank assembly torque the 7/8” U--Bolts to 400 ft. lbs. and the
1--1/4” pivot pin weldment to 530 ft. lbs.
On the rigid or spring cushion shank assembly tighten the 5/8” clamp bolts until the top
clamp leg is parallel to the lower clamp leg.
DECAL ATTACHMENT AND SMV EMBLEM
It is very important that all decals are in place on the ripper as shown in the parts drawing on page P30 of
this manual. These decals, reflectors, safety, and operating messages are just as important as the parts
that have been assembled.
Note: Wipe frame members clean before applying decals for better adhesion. If decals or reflectors
should become faded or damaged be sure to replace them. Assemble the SMV sign to the
frame with the hardware provided (see illustration on page P1). Follow the guidelines for
placement given on page O5 of this manual.

67. 4830 PARTS INDEX APR11
Part Number Page Item Part Number Page Item Part Number Page Item Part Number Page Item
1000-11580-0 P7 27 P21 6 P12 4 P12 48
1000-81066-0 P11 36 P23 25 P13 5 P13 54
1901-0-2 P5 2 P24 2 P14 6 4830-16-0 P7 1
P21 2 P24 2 P12 5 4830-17-0 P4 2
P23 28 P24 2 P13 6 4830-170-1 P29 26
P26 A P24 2 P14 7 4830-18-0 P4 3
P21 1 P21 7 P12 6 P12 41
P23 27 P23 26 P13 7 P13 48
P27 A 24-228R P23 8 P14 8 P14 31
P5 16 P20 3 P12 7 4830-184-0A P13 55
P20 1 P23 3 P13 8 4830-185-0A P13 46
P23 1 P9 9 P14 9 4830-190-0 P13 47
P25 A P21 16 P12 8 4830-200-0 P1 1
21-200 P23 40 P23 17 P13 9 4830-216-1 P17 18
21-2059 P26 P20 4 P14 10 4830-222-0 P17 7
21-2060 P27 P23 4 P12 9 4830-223-0 P17 1
21-2061 P26 1 P21 5 P13 10 4830-224-0 P17 2
21-2062 P27 1 P23 24 P14 11 4830-226-0 P17 14
21-2063 P26 2 25-1105 P29 23 40-156 P17 31 4830-227-0 P15 1
21-2065 P27 2 P21 9 P7 10 P12 46
21-2069 P27 12 P23 9 P11 24 P13 53
21-2072 P27 4 P1 16 41-114 P7 4 4830-27-0 P7 16
21-2073 P27 5 P2 16 P11 31 4830-28-0 P7 17
21-2074 P27 6 P3 16 P19 26 4830-30-0 P9 1
21-2125 P27 7 P20 8 P7 9 4830-300-0 P2 1
21-2126 P26 7 P21 4 P11 25 4830-301-0 P4 8
P26 10 P23 5 41-210 P7 5 4830-302-0 P4 8
P27 10 25-2126 P29 4 P11 30 4830-303-0 P4 9
21-2157 P25 21 P24 7 P19 25 4830-304-0 P4 9
21-2212 P26 6 P24 7 4200-85-5 P29 24 4830-305-0 P4 10
21-2227 P25 20 P24 7 42-109 P7 3 4830-306-0 P4 10
21-225 P26 8 P24 7 42-115 P11 23 4830-34-0 P9 3
P26 13 P21 28 42-134 P19 27 4830-35-0 P9 2
P27 13 P23 37 4400-170-5 P29 8 4830-400-0 P3 1
21-282 P25 2 P24 4 P21 23 4830-50-1 P11 12
21-286 P25 7 P24 4 P23 32 4830-56-0A P19 36
21-288 P25 6 P24 4 P1 23 P1 22
21-318 P23 41 P24 5 P2 23 P2 22
21-319 P23 42 P24 5 P3 23 P3 22
21-320 P23 43 P24 4 4830-0-1 P5 8 P1 18
21-321 P23 45 P24 5 4830-0-10 P7 23 P2 18
21-337 P26 4 P24 5 4830-0-11 P11 9 P3 18
2135-14-0A P7 6 P24 3 4830-0-12 P29 7 4830-70-0 P11 2
2135-54-0 P9 26 P24 3 4830-0-13 P3 17 4830-71-0 P11 1
P26 3 P24 3 4830-0-14 P3 25 4830-73-0 P11 6
P27 3 P24 3 4830-0-15 P29 5 4830-74-0 P11 7
P25 12 P21 29 4830-0-18 P17 20 4830-77-0 P19 9
P26 11 P23 38 4830-0-2 P5 5 4830-78-0 P19 1
P27 11 P21 3 4830-0-20 P15 2 4830-79-0 P19 3
P26 24 P23 29 4830-0-21 P17 19 4830-80-0 P19 2
P27 24 25-304 P23 7 4830-0-3 P5 1 4830-81-0A P19 16
P9 11 P21 27 P1 3 P12 42
P21 10 P23 36 P2 2 P13 49
P23 11 P20 5 P3 2 P14 32
P9 10 P23 6 P1 2 4830-83-1 P19 8
P21 15 30-244 P19 31 P2 3 4830-83-2 P19 10
P23 16 P12 1 P3 3 4830-84-0B P12 47
P26 9 P14 1 P9 15 4830-85-0B P14 33
P27 9 P12 54 4830-0-6 P5 13 P20 6
21-738 P25 5 P13 1 P1 4 P23 21
21-807 P26 12 P14 2 P2 4 P20 7
21-810 P26 5 P12 55 P3 4 P23 20
21-819 P27 8 P13 2 P1 17 P24 1
21-872 P25 10 P14 3 P2 17 P21 19
21-876 P23 44 P12 45 P3 17 P23 22
21-879 P25 3 P13 52 4830-125-1 P13 41 P24 1
21-893 P25 1 P12 2 4830-125-2 P13 42 P21 20
21-894 P25 4 P13 3 4830-125-3 P13 43 P24 1
21-895 P25 P14 4 P12 39 P12 44
2190-51-1 P11 40 P12 3 P13 44 P13 51
P20 3 P13 4 P14 29 4885-0-5 P9 25
P23 3 P14 5 P12 40 4885-0-6 P9 27
P20 4 P13 45 P12 49
P23 4 P14 30 P13 56
21-1007
21-1008
21-171
21-2127
21-260
21-381
21-404
21-443
2145-170-3
2145-170-5
21-702
24-201R
24-209R
24-2101R
24-2104R
24-2120R
24-225R
24-256R
2426-170-5
24-292R
24-299R
25-1153
25-1163
25-126
25-221
25-2272
25-2289
25-2290
25-2291
25-2295
25-300
25-301
25-314
25-373
31-208
31-215
31-216
31-217
33-194
33-195
33-196
33-197
33-205
33-211
33-212
33-213A
41-112
41-117
41-208
41-215
44-107
4600-0-28
4830-0-4
4830-0-5
4830-0-7
4830-0-8
4830-125-4
4830-132-0
4830-145-2
4830-182-0AR
4830-26-0A
4830-58-0
4830-59-0A
4830-82-0C
4830-91-0
4830-92-0
4830-93-0
4830-94-0
4850-25-3
4885-80-1
Index - 1

68. 4830 PARTS INDEX APR11
Part Number Page Item Part Number Page Item Part Number Page Item Part Number Page Item
P12 50 P9 21 P1 11 P12 30
P13 57 P12 18 P2 11 P13 32
P12 43 P13 19 P3 11 P14 24
P13 50 P1 5 P29 13 P17 4
P12 51 P2 5 P12 53 P12 31
P13 58 P3 5 P13 24 P13 33
P12 52 P5 6 P14 20 63-128 P5 3
P13 59 P9 16 P17 10 63-129 P9 5
4930-91-0 P24 1 P3 26 P29 9 P12 32
4938-0-19 P17 21 P19 6 P12 23 P13 34
4938-94-0 P23 23 60-626 P9 34 P13 25 P14 25
P20 2 60-702 P7 13 P12 24 P17 17
P23 2 60-703 P11 21 P13 26 P17 34
4990-114-0 P11 28 60-706 P19 5 62-463 P17 32 P12 33
51-106 P7 31 60-708 P11 19 62-474 P19 24 P13 35
51-107 P7 30 60-711 P5 4 62-481 P14 21 P14 26
51-120 P11 38 P1 24 P21 8 63-201 P11 33
51-121 P11 39 P2 24 P23 10 63-204 P7 12
51-206 P17 29 P3 24 62-498 P11 26 63-209 P11 27
5210-0-4422 P19 33 P9 33 62-521 P7 21 63-210 P19 29
52-103 P7 28 60-724 P19 30 62-569 P17 8 63-304 P19 37
5210-383-1 P17 25 60-725 P11 34 62-651 P15 3 P1 13
5210-445-0A P19 22 61-111 P11 8 P24 6 P2 13
52-109 P11 37 P21 22 P24 6 P3 13
52-301 P19 32 P23 31 P24 6 P29 14
52-302 P7 14 P1 19 P24 6 P1 12
52-305 P11 35 P2 19 P12 25 P2 12
52-411 P17 30 P3 19 P13 27 P3 12
52-512A P17 28 P19 17 P12 26 P29 6
P3 27 P1 8 P13 28 P12 34
P12 10 P2 8 P1 14 P13 36
P13 11 P3 8 P2 14 P14 27
P19 38 P29 16 P3 14 P17 11
53-102 P7 24 6127-0-11 P9 22 P29 15 P29 11
P12 11 61-281 P13 20 P17 12 64-104 P29 10
P13 12 61-282 P19 20 P21 24 P1 9
53-108 P7 2 61-285 P17 15 P23 33 P2 9
53-111 P11 22 6142-82-0 P9 6 P29 12 P3 9
53-113 P9 20 6200-90-0 P9 31 P1 10 P7 19
53-118 P7 25 6200-90-1 P9 32 P2 10 P9 30
P12 12 62-143 P17 22 P3 10 P11 4
P13 13 62-172 P19 14 P7 20 P17 23
P12 13 62-176 P9 23 P9 28 P19 34
P13 14 62-178 P14 16 P11 5 P21 13
P12 14 P4 4 P17 24 P23 14
P13 15 P12 19 P19 35 P29 17
53-166 P7 26 P14 17 P21 14 P9 29
53-167 P14 12 62-246 P17 3 P23 15 P17 9
P12 15 62-251 P17 3 P29 18 P21 12
P13 16 62-295 P7 8 P9 12 P23 13
P14 13 P9 13 P12 27 P1 20
5510-127-0 P9 19 P21 11 P13 29 P2 20
5630-0-23 P9 18 P23 12 P21 18 P3 20
5660-0-11 P5 12 P12 20 P23 19 P11 14
5660-0-6 P5 10 P17 5 P1 21 P19 18
5660-0-7 P5 9 P17 26 P2 21 P12 35
5660-0-8 P5 11 P7 18 P3 21 P13 37
5800-17-0 P21 21 P9 8 P11 15 P4 5
5800-17-0 P23 30 P21 17 P19 19 P11 10
P1 6 P23 18 P9 24 P12 36
P2 6 P12 20 P12 28 P14 28
P3 6 P13 21 P13 30 64-113 P19 12
P9 14 62-352 P11 3 P14 22 64-115 P13 38
P21 25 62-372 P11 16 P17 6 64-118 P15 4
P23 34 P11 13 P17 27 64-120 P7 11
60-120 P5 15 P17 5 P19 15 64-125 P7 22
P12 16 P12 21 P19 21 P12 37
P13 17 P13 22 P4 6 P13 39
P14 14 P14 18 P11 11 P5 7
P12 17 62-396 P17 33 P12 29 P19 4
P13 18 P12 22 P14 23 64-148 P17 16
P14 15 P13 23 P19 13 64-160 P19 28
60-200 P11 20 P14 19 63-115 P13 31 64-161 P11 32
60-605 P5 14 63-117 P15 5 65-101 P11 29
4885-80-2
4885-80-3
4885-87-0B
4885-88-0B
4956-75-0
53-101
53-103
53-119
53-136
53-148
53-168
60-102
60-103
60-130
60-131
60-606
60-615
60-617
60-716
6124-17-1
61-261
61-268
62-195
62-300
62-339
62-343
62-351
62-393
62-394
62-415
62-417
62-432
62-436
62-439
62-441
62-491
62-656
62-820
63-100
63-102
63-106
62-872
63-107
63-109
63-110
63-112
63-119
63-126
63-134
63-135
63-139
64-100
64-110
64-112
64-126
64-127
64-101
64-102
64-103
64-107
64-108
64-109
Index - 2

69. 4830 PARTS INDEX APR11
Part Number Page Item Part Number Page Item Part Number Page Item Part Number Page Item
P5 17
P12 38
P13 40
P19 23
65-114 P9 4
P7 15
P7 7
P19 7
70-212 P11 17
70-212-1 P11 18
72-351 P9 17
73-100 P9 7
74-100 P30 1
P30 3
P30 5
74-109 P7 29
P25 8
P26 25
P27 25
74-276 P30 3
P21 26
P23 35
74-465 P30 10
P1 7
P2 7
P3 7
74-516 P26 23
74-517 P27 23
74-549 P30 9
74-550 P30 8
74-570 P30 2
P21 30
P23 39
P29 19
P30 7
P29 19
P30 4
P29 19
P30 6
74-674 P30 11
76-226 P19 11
76-235 P17 13
79-397 P29 25
79-546 P29 2
79-547 P29 1
79-549 P29 3
79-550 P29 1
79-551 P29 3
79-552 P29 20
79-577 P29 21
79-578 P29 22
P1 15
P2 15
P3 15
65-110
65-119
74-102
74-113
74-387
74-487
74-574
74-575
74-576
74-577
99-218
Index - 3