Coping and Utilizing advanced solar air field lights of avlite product

1. Avlite Systems
Solar Airfield Light
Global reputation for unsurpassed reliability…

2. TECHNOLOGY
Solar lighting systems
LED as light source
Solar LED lighting best value of money at 1/3 of
the cost of mains power lighting installation
Suitable as an emergency back-up system
installed alongside traditional mains-powered
lighting

3. OPERATING PRINCIPLE
Solar module converts sunlight to a electrical current used
to charge the battery at day
The battery provides power to operate at night
Microprocessor drives an array of LED through DC/DC
converter
Over charging protection
If the light has auto control then, On darkness, the
microprocessor initiate a program check and after
approximately 1 min. the light turn on.

4. PRODUCTS
OF
AVLITE

5. AV-70 MODEL
Used in such as runways, taxiways and helipads
Operating reliably in low sunlight conditions
Incorporate dual high performance solar modules

6. FEATURES
Integrated solar /battery system
Fast and easy to deploy –no
programming
IP68 rating
User-replaceable battery
Ultra- high intensity LEDs

7. AV-70

8. AVLITE AV-70-G-SW
A)LIGHT CHARACTERISTICS
Light Source: 12 ultra-high intensity LEDS
Peak Intensity (cd): Steady on( Blue -2.8 Red -6.8,
Green-9 white7 Yellow-6.5)
Flashing(Blue -5.5 Red -18.2 Green-21.9 white-
19.1 Yellow-15.1)
 Horizontal Output (degree): 360
Reflector type: Omni directional 360 degree LED
reflector

9. ELECTRICAL CHARACTERISTICS
 Operating voltage(V): 3.6
 Temperature Range: -40 to 80⁰C
Solar Characteristics
 Solar Module type: Multicrystalline
 Output Power: 2.5 (2X1.25) watt
 Solar Module Efficiency(%): 14
 Charging Regulation: Microprocessor control

10. Power supply
Battery type: High grade NIMH
Battery Capacity: 8 Ahr
Nominal voltage: 3.6 V

11. Light Operation
 Light is activated by ON/OFF Switch
 Intensity and flash settings need to be set prior to
installation
i)Remove the marked flash adjustment bung from the
base of the light and set internal toggle switch to ‘ON’

12. ii)Using DIP switches, Intensity setting of the lights are
adjusted
iii)Set rotary switches to the required flash code
iv)Replace flash adjustment bung

13. INSTALLING THE LIGHT ASSEMBLY: MOUNTING
OPTIONS
 Rubber tile
Rubber Tile Installation

14.  Frangible Concrete Mount
Fig: Frangible Concrete Mount Installation

15.  Frangible Stake Mount
Frangible Stake Mount Installation

17. AV-70-RF MODEL

18. INTRODUCTION
 Radio controlled version of AV70
 Allows pilot safely navigate runways and
apron areas
 Used in conjunction with Pilot Activated
Lighting Control(PALC) or simple hand held
controller
Fig: PALC Fig: Handheld controller

19. AV-ALS-RC-2.4-AVMESH
Radio Controlled Front
View
Radio Controlled Side
View

20. AV-ALS-RC-2.4-AVMESH
 A model of Handheld controller
Features
Range: Up to 1.4 KM
Temperature: -40 to 80⁰C
Frequency: 2.4GHz
Nominal Voltage: 7.2 V
Battery Capacity: 4 Ah

21. AVLITE:AV-70-B-RF
 Works by using a hand held radio
controller and setup entire airfield,
airport or air base.
 Each light also has an operational
range of 1.4 Km

22. MODES OF OPERATION
 Always ON operational Mode
 STANDBY operational mode
 Dusk till Dawn Operational mode
Light Group
 Light is selected through rotary switch
 Controller can select any one of the 10 individual light
groups or all (By default 0)

23. Timeout Duration
 Visible only when timeout model is enabled
 Time before the LED intensity reverts back to its LOW
intensity state or standby
 Duration can set from 1 to 60 minutes
LED Bank Setup
 Allow a runway to change from visible to IR
Battery Diagnostic
 Used to check the battery voltage in every light
 If the battery voltage is within operational range the
light will turn off for 1 sec, flash once for 1 sec and
again turn off for 1 sec.
 Otherwise, the light will turn off for 1 sec, flash twice
then turn off for 1 sec

24. Graph for Diagnostic Test
Sending Command
Every time command is set by pressing SEND
button
Better to have diagnostic test once per day

25. Red Status LED
 Determine the fault
 Present in radio controlled model
 Situated near the Flash Code Switches

26.  Runway B Only is to be High Intensity, with a Timeout of
8 minutes and Runway A will be low Intensity

27. Flash Codes
 All AV-70-RF lights are programmed to be steady on
 Alternatively, they are able to be programmed to flash in
any of the 250 different flash codes i.e 00 to FF

28. Charging the radio controller
 Unscrew the protective cap from the charging port
 Insert the charging terminal into the Radio controller
 Plug the charger into a wall socket and turn the charger
on
 The charger has a LED to indicate the charge
sequences
i) green: Unit is fully charged
ii) orange: Unit is charging
iii) Red: A fault is occuring

29. PROGRAMMING THE RADIO CONTROL SYSTEM
 Turn on radio controller
 Press and hold the menu button for 3 sec
 Menu contains following submenu
a. Screen back light
b. Connection method
i) Radio control
ii) Direct connection
c. Flash code selection- Enable or disable
d. Sync. Menu selection- Enable or disable
e. Advanced operation- Enable or disable
f. Diagnostic- Enable or disable
g. Radio information

30. i. Radio encryption key
If you change the radio encryption key then, the light
encryption key by which that remote control should
also changes
j. Press ‘send’ to save the Radio Control System

31. AV-425-RF-Model

32. FEATURES
 Peak intensity(cd): Steady on (Red 25, Green
37, white 27.5, yellow 92.5)
 Operating voltage: 12 V
 Solar module type: Multi crystalline
 Output: 18 watt
 Battery: Sealed Lead Acid
 Battery Capacity: 24 Ah

33. PROGRAMMING THE LIGHT USING CABLE
INTERFACE AND HAND HELD CONTROLLER
NOTE: PRESS ‘SEND’ AFTER EACH SELECTION
 Remove the light head to access the programming port
 Connect the programming cable between light and radio
controller
 Turn on the radio controlled
 Turn on light at the red master switch
 Press and hold the menu for 3 sec
 Using menu key scroll down submenu to connection
method and select direct connection

34.  Advanced operation mode
 Light group: 0 to 10 or all
 Intensity: Low, Medium or High
 Flash code : From 000 to 1FF
 Sync. Offset: (If sync is enabled during radio control
system programming)
 Radio encryption key
Now, put the radio controller to the radio connection mode

35. AVLITE OBSTRUCTION LIGHT
AV-OL-ILAB-12-R
 Universal DC Low intensity
obstruction light
 Operating range: 12 to 48
VDC
 Alarm relay for internal
diagnostic checking
( supply voltage too low, LED
failure etc)
 Adjustable intensity setting
i) Type A: 10 cd
ii) Type B: 32 cd
 Battery: 26 Ah

36.  Current draw (mA) @12 V
Type A @ 10 cd steady on Imax=65
Type B @ 32 cd steady on Imax = 120
 Power (W)
Type A @ 10 cd steady on Pmax=0.9
Type B @ 32 cd steady on Pmax = 1.5

37. OPERATION
 Turn ON <=100 lux
 Turn OFF>=150 lux
Intensity setting
 Open the light head
 Change the intensity DIP switch

38. AV-OL-ILAB-UM-R
 Universal AC Low
intensity Obstruction
Light
 Operating Range 110 to
240 V AC
 Power
Type A @ 10 cd steady
on Pmax=2 W
Type B @ 32 cd steady
on Pmax = 3W
 Others all the
properties and
operational principle
similar to AV-OL-ILAB-
12-R

39. Any
queries
END
AND
THANK YOU
EVERY ONE FOR
LISTENING