This document discusses multiple antenna techniques used in wireless communications. It describes MIMO systems and how they can provide spatial diversity and multiplexing to improve reliability and increase data rates. Spatial diversity techniques like receive and transmit diversity are covered, as well as spatial multiplexing approaches including open and closed loop methods. Beamforming and multi-user MIMO techniques for the uplink and downlink are also summarized. The document provides details on how these different multiple antenna techniques work to overcome challenges like fading and interference.
4. MIMO System
Communication system obstacles ?
Suffers from Co–channel interference and signal level fading
Channel limits the bandwidth
power falls off with distance
Why MIMO ?
Significant increase in spectral efficiency and data rates
High Quality of Service (QoS)
Wide coverage, etc.
By using Multiple Antenna techniques:
Diversity gain mitigates the fading and increases coverage and
improves QoS
Multiplexing gain increases capacity and spectral efficiency with no
additional power or bandwidth expenditure
5. MIMO System
in Spatial diversity, same information of multiple copies is
sent across independent fading channels to combat fading,
improving Reliability
in Spatial multiplexing, each spatial channel carries
independent information, thereby increasing the data rate of the
system
7. Spatial Diversity
Receive Diversity
Most often used in the uplink.
Two copies of the same data are put on two different channels
having independent fading characteristics.
Signals reach the receive antennas with different phase shifts.
8. Spatial Diversity
Closed Loop Transmit Diversity
Signals Transmit from transmit antennas with different
phase shifts.
The phase shift is determined by a pre-coding matrix
indicator (PMI), which is calculated by the receiver and fed
back to the transmitter.
9. Spatial Diversity
Open Loop Transmit Diversity
the transmitter uses two antennas with two successive time steps :
Transmitter sends S1 from the First antenna and S2 from the
second Antenna.
Transmitter sends –S2∗ from the first antenna and S1∗ from
the Second antenna .
The receiver can now make two successive measurements of the
received signal, which correspond to two different combinations
of S1 and S2.
10. Spatial Multiplexing
When one antenna transmits a reference symbol, the other
antenna keeps idle until the first antenna finishes transmitting.
The receiver can estimate the channel elements H11 and H21
then after, H12 and H22 using Zero forcing detector technique.
Therefore, transferring two symbols at the same time using the
same sub-carriers, and have doubled the data rate.
11. Spatial Multiplexing
Open Loop Spatial Multiplexing
There is a problem with the technique described before.
Denominator could be zero using symbol estimation
equation 𝑥1 =
𝐻22∗𝑦1 −𝐻12∗𝑦2
𝐻11∗𝐻22 −𝐻21∗𝐻12
To solve this problem:
the receiver measures the channel elements and works out a
Rank indication (RI), which indicates the number of symbols
that it can successfully receive at a certain location.
If RI = 2 => x1 = s1 - x2 = s2 , as before
If RI = 1 => x1 = s1 - x2 = s1 , Then the receiver equation
will be: y1 = H11*s1 + H12*s1 +n1
y2 = H21*s2 + H22*s2 +n2
13. Spatial Multiplexing
Closed Loop Spatial Multiplexing
There is a problem with the technique described before.
using the earlier equation of: y1 = H11*s1 + H12*s1 +n1,
assuming H11 = - H12 , this will leads to that the reciver will
only receive the noise power : y1 = (s1 + (-s1)) + n1
To solve this problem:
the receiver measures the channel elements and works out a
Rank indication (RI) and a Pre-Coding Matrix Indicator (PMI)
If RI = 1 and no PMI => x1 = s1 - x2 = s1 , as before
If RI = 1 and has PMI => x1 = s1 - x2 = -s1 , Then the
receiver equation will be: y1 = H11*s1 + H12*(-s1) +n1
y2 = H21*s2 + H22*(-s2) +n2
15. Spatial Multiplexing
Implementation Issues :
If the antennas are too close together, then the
channel elements Hij will be very similar.
in the case of line-of-sight transmission and
reception, the channel elements Hij are
uncorrelated with each other.
For fast moving mobiles, delays in the feedback
loop can make the PMI unreliable by the time the
transmitter comes to use it, so open loop spatial
multiplexing is often preferred.
16. BeamForming
similar to diversity transmission and reception.
multiple antennas separation is less than diversity technique,
typically half a wavelength of the carrier frequency.
multiple antennas increase the coverage of the cell
main beam pointing towards mobile 1 and a null pointing
towards mobile 2
17. Beam Steering
By applying a phase ramp to the transmitted signals, we can
change the direction at which constructive interference arises.
By applying a suitable set of antenna weights. In a system
with “ N ” antennas, this allows us to adjust the direction of
the main beam and up to N - 2 nulls or sidelobes.
It can also be used to construct a synthetic reception beam for
the uplink.
18. Multiuser MIMO
uses multiple antennas to improve communication by creating
multiple connections to the same device at the same time.
helps relieve this potential congestion by creating multiple
connections to a device at the same time, which increase network
efficiency
Takes advantage of multi-path reflecting and signal cooperating.
20. Multiuser MIMO
Uplink MU-MIMO
Mobiles transmit at the same time and on the same carrier frequency,
but without using any pre-coding technique.
The base station receives their transmissions and separates them
using some techniques.
This technique only works if the channel matrix is well behaved.
The base station can freely choose mobiles that lead to a well-behaved
channel matrix.
This technique does not increase the peak data rate of an individual
mobile, but it is still beneficial because of the increase in cell
throughput.
22. Multiuser MIMO
Downlink MU-MIMO
Base Station transmit sends two different data streams into its antenna
array instead of just one , using any pre-coding technique.
Neither mobile has complete knowledge of the channel elements or of the
received signals.
Transmitter has created two separate antenna beams, which share the
same sub-carriers but carry two different sets of information to be steered.
23. Multiuser MIMO
Benefits of MU-MIMO
use of beamforming to direct signals toward a device.
decrease in the time each device has to wait for signals.
increase in the capacity and efficiency of a user.
Less affected by antenna correlation and channel rank
loss.
user's devices do not have to use multiple antennas.
can improve video playback streams and eliminate
some buffering or lower video quality.