VIP Call Girls Service Kondapur Hyderabad Call +91-8250192130
El epm01 en
1. ENGLISH
INSTRUCTIONS
EL-EPM01
Energy Meter
Introduction:
The EL-PM01 Energy Meter is developed for monitoring and
measuring electrical loads. It provides an efficient solution to help
determinate costs.
The measurement range of the Energy Meter extends
from 5W to 3680W (max. current 16A). If values fall below
or exceed these limit values, exact measurements are no
longer possible. Also the device could be overloaded and
thereby destroyed.
Features:
• Current time (24 hours), week, load power and cost tariff.
• Total time, total used energy and accrued energy cost.
• Total record time, total time and percentage.
• Dual programmable power tariffs.
Before Use:
• The Energy Meter is only for operation at 230V AC. Only power
loads with a power supply of 230V AC 50/60Hz may be connected.
• Operation of the Energy Meter is only permitted in interior spaces
and dry environments. Do not use the Energy Meter outside.
• Always observe the identification labels of connected devices to
check if the specifications comply with the Energy Meter.
Connection:
After connecting the Energy Meter to an outlet and power load the
condensers in the device will be charged. After five minutes, the
condensers will have enough power to show the LCD display. Then
the current time and power tariff can be set.
Note: The internal Li-ion battery for showing the LCD display needs
at least 12 hours to charge fully.
1
2. Operation:
Setting of current time and week
SET TIME
1. Press "+" and "-"
buttons together to enter
system setting. First setting
is the current time.
2. Increase with "+" button the
value of the blinking position
(0 to 9). Decrease with
"-" button the value of the
blinking position (0 to 9).
3. Press "MODE" button to
select next position.
4. After the setting of week,
press "MODE" button. The
Energy Meter will enter the
setting of cost tariff 1.
12:00
MON
Setting cost tariff 1
SET COST
1. Set the start time of cost
tariff 1.
2. Set the value of tariff 1.
3. Increase with "+" button the
value of the blinking position
(0 to 9). Decrease with
"-" button the value of the
blinking position (0 to 9).
4. Press "MODE" button to
select next position.
5. Press "MODE" button, the
Energy Meter will enter the
setting of cost tariff 2.
Cost/h1 07:00
10:00 Cost/h
2
3. 3
The setting of cost tariff 2
SET COST
1. Set the start time of cost
tariff 2
2. Set the value of tariff 2.
3. Increase with "+" button the
value of the blinking position
(0 to 9). Decrease with
"-" button the value of the
blinking position (0 to 9).
4. Press "MODE" button to
select next position.
5. To stop, press longer than 5
seconds to confirm all settings.
Cost/h2 20:00
8:00 Cost/h
Three screens are available to display different figures. Press "MODE"
button to select.
1. Display of current time (24 hours type), week, load power and
current cost tariff.
12:00 Current time
0 W Load power
0.0 Cost/h Current cost tariff
MON Week day
2. Display of total record time, total used energy and accrued energy
cost.
Total Cost Current time
0.40 RECh Total record
0 kwh Total used energy
0.0 Accrued energy cost
4. TotalTime Current time
0.40 RECh Total record
0.24 ONh Total on time
60 % Accrued energy cost
Technical data
Operating voltage: 230V AC/50/60Hz alternating voltage
(AC)
Max connected power: 3680w
Max current: 16A
Rechargeable battery: 3.6V, 40mAH, 12H, 4mA
Input/Output: via protected contact plug/outlet
Working temperature: +10°C to +40°C
Energy display: 0kwh-999.9kwh
Max record time: 9999hours
Using indoor only, altitude
under 2000m
Working temperature: +5°C to +40°C
Working humidity: 80% under 31°C from 31°C to 40°C,
this figure decreases to 50% linearly.
IP20
Pollution degree: 2
Notes: Only one Energy Meter can be used in the same time.
3. Display of total record time, total on time and percentage
4
4. Reset
Press "MODE", "+" "-"simultaneously to delete all data (the data of
current time and the week will not be deleted) after 5 seconds.