1. Applied Mechanics and Materials Vols. 766-767 (2015) pp 38-43 Submitted: 2015-01-20
© (2015) Trans Tech Publications, Switzerland Revised: 2015-01-30
doi:10.4028/www.scientific.net/AMM.766-767.38 Accepted: 2015-02-05
Online: 2015-06-08
All rights reserved. No part of contents of this paper may be reproduced or transmitted in any form or by any means without the written permission of Trans
Tech Publications, www.ttp.net. (ID: 117.207.68.195-14/07/15,13:08:41)

2. Applied Mechanics and Materials Vols. 766-767 39

3. 40 Advances in Materials and Manufacturing

4. Applied Mechanics and Materials Vols. 766-767 41

5. •
•
•
•
42 Advances in Materials and Manufacturing

6. Applied Mechanics and Materials Vols. 766-767 43

7. Advances in Materials and Manufacturing
10.4028/www.scientific.net/AMM.766-767
Parametric Optimization of AWJM in AA6351-SiC-B4C Hybrid Composite Using Grey Relational
Analysis
10.4028/www.scientific.net/AMM.766-767.38
DOI References
[1] S. Thirumalai Kumaran, M. Uthayakumar, Investigation on the machining studies of AA6351SiC-B4C
hybrid metal matrix composites, International Journal of Machining and Machinability of Materials 15 (2014)
174-185.
http://dx.doi.org/10.1504/IJMMM.2014.060548
[2] S. Suresh Kumar, M. Uthayakumar, S. Thirumalai Kumaran, P. Parameswaran, Electrical Discharge
Machining of Al(6351)-SiC-B4C hybrid composite, Materials and Manufacturing Processes 29 (2014) 1395-
1400.
http://dx.doi.org/10.1080/10426914.2014.952024
[3] L. Chen, E. Siores, W.C.K. Wong, Kerf characteristics in abrasive waterjet cutting of ceramic materials,
Machine Tools and Manufacture 36 (1996) 1201-1206.
http://dx.doi.org/10.1016/0890-6955(95)00108-5
[4] D.K. Shanmugam, S.H. Masood, An investigation on kerf characteristics in abrasive waterjet cutting of
layered composites, Journal of Materials Processing Technology 209 (2009) 3887-3893.
http://dx.doi.org/10.1016/j.jmatprotec.2008.09.001
[6] J. Wang, A new model for predicting the depth of cut in abrasive waterjet contouring of alumina ceramics,
Journal of Materials Processing Technology 209 (2009) 2314-2320.
http://dx.doi.org/10.1016/j.jmatprotec.2008.05.021
[8] S. Thirumalai Kumaran, M. Uthayakumar, S. Aravindan, Analysis of dry sliding friction and wear
behavior of AA6351-SiC-B4C composites using Grey Relational Analysis, TribologyMaterials, Surfaces and
Interfaces 8 (2014) 187-193.
http://dx.doi.org/10.1179/1751584X14Y.0000000075
[9] S. Suresh Kumar, M. Uthayakumar, S. Thirumalai Kumaran, P. Parameswaran, E. Mohandas, Electrical
Discharge Machining of Al(6351)-SiC-B4C hybrid composite: A Grey Relational approach, Modelling and
Simulation in Engineering 2014 (2014) 7.
http://dx.doi.org/10.1155/2014/426718
[10] M. Uthayakumar, S. Thirumalai Kumaran, S. Aravindan, Dry sliding friction and wear studies of fly ash
reinforced AA-6351 metal matrix composites, Advances in Tribology 2013 (2013) 6.
http://dx.doi.org/10.1155/2013/365602