FloorTeq Epoxy Coating

1. FloorTeq, is a 1:1 mixture epoxy
paint. It has been proven to last in
excess of 20 years on workshop,
warehouse and plant floors and has
been tested by the SABS, CSIR and
many other reputable companies.
DURABLE
TESTED
PROVEN
Copyright Shamrock Group Holdings (Pty) Ltd South Africa. www.shamrockroup.co.za

2. What is FloorTeq?
FloorTeq is a simple 1:1 mixing
ratio, Polyamide Epoxy Coating
System, suitable for applying on:
• Workshop Floors
• Hospitals Floors
• Clinic Floors
• Food Processing Plant Floors
• Dairy Floors
• Bakery Floors
• Butchery Floors
• Production Plant Floors
• And many more..
Non Static
Self Priming
Resistant to Solvents
Resistant to Alkalis
Resistant to Acids
Non Toxic
Non Slip Finish Available
Applied for Demarcations
High Combustion Rating
Non Static
Self Leveling Compatible
Self Polishing
ADVANTAGES
NO PRIMER
REQUIRED

3. What is surfaces can FloorTeq be applied on?
FloorTeq can be applied to most flooring substrates. New concrete
(Curing Schedules Apply) is the easiest and most common of our
applications. Previously painted or coated surfaces must be reduced to
the original concrete by means of floor grinding, manual grinding,
chemical treatments etc. All applications are very subject to surface
preparation.
DARK GREY
LIGHT GREY
GREEN
YELLOW
RED
Colours Available
Standard colours are manufactured
as indicated below. We manufacture
any colour available on request and
subject to availability. Additional
costs may occur.

4. Coated ConcreteSoiled, Old ConcreteNew Concrete
Surface Preparation
New concrete floors must be
swept from all loose debris,
dust and contaminants. The
entire floor MUST be washed
with an industrial high
pressure water machine.
Suggested output rating
should be no less than 150
Bar.
Unpainted, soiled concrete
must be degreased and
cleaned prior to any
application. A suitable
degrease must be applied
and brushed vigorously to
remove surface greases
and oils. Wash the entire
floor after degreasing with
an industrial high pressure
water machine. Suggested
output rating should be no
less than 150 Bar / 15lt
per minute.
Check the entire floor
while washing that the
surface is “water break
free” i.e., the water should
make a uniform layer over
the floor. Should the water
“break” in some areas,
repeat the degreasing and
washing procedure.
Previously painted surfaces
must be treated properly
and in most instances, the
original coating must be
reduced to the bare
substrate (Concrete).
The most common is a floor
grinder, that can be hired
from most Tool Hire Outlets.
Remove all coatings.
A suitable degrease must be
applied and brushed
vigorously to remove surface
greases and oils. Wash the
entire floor after degreasing
with an industrial high
pressure water machine.
Suggested output rating
should be no less than 150
Bar / 15lt per minute.

5. ApplicationMixing
Mixing and Application
FloorTeq is an equal part
mixture. The BASE is the
coloured fluid (B). The
ACTIVATOR is the semi clear
fluid (A). DO NOT MIX THESE
COMPONENTS IF YOU DO
NOT INTEND USING THEM
WITHIN 4 HOURS.
The Activator and Base must
be mixed in equal quantities
eg. 5lt Activator with 5Lt
Base. Only mix a maximum of
half your order for the
primary coat.
Using a clean container, add
equal amounts of Activator
and Base. A measuring
paddle can be used for
indication purposes.
With a paddle or electric
paint paddle, mix the mixture
until a uniform consistency.
Leave the mixture 30
minutes before applying,
mixing it in intervals of 5
minutes.
After 30 minutes, the
product is ready to be used.
FloorTeq can be applied by
the following methods:
• Roller
• Brush
• Conventional Spray
• Airless Spray.
The substrate must be clean
of all loose debris, dust and
foreign materials. Masking
may be done to protect
other areas with masking
tape.
Apply the first coat, without
pooling. Using a dry roller
(not dipped in FloorTeq),
move over the area again in
a single direction. Mix
batches of FloorTeq in
smaller quantities.
Allow 12 hours to cure
before recoating or applying
the second coat.
Allow at least 24 hours for
light foot traffic.

6. Product Usage Chart
Area (Sqm) FloorTeq Required
5Sqm 1.67Lts
10Sqm 3.33Lts
15Sqm 5.00Lts
20Sqm 6.67Lts
25Sqm 8.33Lts
30Sqm 10.00 Lts
35Sqm 11.67 Lts
40Sqm 13.33 Lts
45Sqm 15.00 Lts
50Sqm 16.67 Lts
55Sqm 18.33 Lts
60Sqm 20.00 Lts
65Sqm 21.67 Lts
70Sqm 23.33 Lts
75Sqm 25.00 Lts
80Sqm 26.67 Lts
85Sqm 28.33 Lts
90Sqm 30.00 Lts
95Sqm 31.67 Lts
100Sqm 33.33 Lts
110Sqm 36.67 Lts
120Sqm 40.00 Lts
130Sqm 43.33 Lts
140Sqm 46.67 Lts
150Sqm 50.00 Lts
160Sqm 53.33 Lts
170Sqm 56.67 Lts
180Sqm 60.00 Lts
190Sqm 63.33 Lts
200Sqm 66.67 Lts
210Sqm 70.00 Lts
220Sqm 73.33 Lts
230Sqm 76.67 Lts
240Sqm 80.00 Lts
250Sqm 83.33 Lts
260Sqm 86.67 Lts
270Sqm 90.00 Lts
280Sqm 93.33 Lts
290Sqm 96.67 Lts
300Sqm 100.00 Lts

7. Technical Data
Limitations
FloorTeq can be applied in
ambient temperatures of
15°C and 35°C. Relative
humidity should not exceed
50%. Substrate temperatures
should not be below 15°C
and not higher than 50°C.
The product should never be
exposed to conditions, other
than what was tested for.

8. Product Catalogue
FLOORTEQ 10 LT DIY KIT
This DIY Kit contains 10lts (5 Activator and 5 Base) of product,
which will cover 30sqm of floor area. It also includes 2 x Genuine
Sheepskin Rollers and 2 X 50mm Fine Bristle Brushes. All kits
include a user manual link to be downloaded.. Standard colours
available
FLOORTEQ 20 LT DIY KIT
This DIY Kit contains 20lts (10 Activator and 10 Base) of product,
which will cover 60 sqm of floor area. It also includes 2 x Genuine
Sheepskin Rollers and 2 X 50mm Fine Bristle Brushes. All kits
include a user manual link to be downloaded.. Standard colours
available
FloorTeq is supplied in the following packaging:
• 5Lt Packs 2.5 Base and 2.5 Activator
• 10Lt Packs 5 Lt Base and 5 Lt Activator
• 20 Lt Packs 10Lt Base and 10 Lt Activator
• 40 Lt Packs 20Lt Base and 20Lt Activator
• Custom packaging available

9. Contact Details
South Africa
Shamrock Group Holdings
www.shamrockgroup.co.za Gerrit Myburgh
info@shamrockgroup.co.za Mobile +27 82 924 0837
Namibia
GK Agencies
Windhoek Gunther Kuhn
gkagent@afol.com.na Mobile +264 81 129 4523
Zambia
Shamrock Group Zambia
www.zambia.shamrockgroupsa.com Garvin Miyambo
zambia@shamrockgroupsa.com Mobile +260 96 860 9067