CCS355 Neural Network & Deep Learning UNIT III notes and Question bank .pdf
Eim answer key 2019 gem
1. ANSWER KEY
___1. Which one of the tool havinga cross tip end?
a. Philip Screw Driver b. FlatScrew Driver c. Screw Driver d. Screw Nut
___2. What is the most known tools that can be used in the cutting and pullingthenail?
a. Nail cutter b. Wire cutter c. Hammer d. Nail puller
___3. How would you classify thelong-noseflier?
a. It ends with longarms holder c. It ends with longtips
b. Having a grip and long part end d. None of these
___4. Which is the best answer of 3 way to 4 way switch connection?
a. Connected to each other c. Cross connection
b. Connected by each sign number d. All of the above
___5. What materials would you choose from loosen to tighten the utility box?
a. Philip ScrewDriver b. FlatScrew Driver c. Screw Driver d. Screw Nut
___6. How would you show your understandingabout wiringplan?
a. It’s a guide to follow the correct connection of a wiring method c. It’s a plan for preparation in connection
b. It’s wiringplan d. All of the above
___7. How would you use the proper electrician knife?
a. For cutting b. For gripping c. For skinning d. For loosening
___8. What other way would you install a wirewhich is the PDX is a proper use?
a. Duplex b. TW c. Telephone wire d. # 4 of PDX
___9. What materials s would you choose to cover the skinningwire?
a. Maskingtape b. Electrical tape c. Aramark Tape d. All of the above
___10. What facts would you select a cutting a different wires and nails?
a. Plier b, Knife c. Hacksaw d. Drill
___11. How would you classify a number of standard wireto install thebulb and switch?
a. 2,4,6 b, 8,10,12 c, 10,12 d, 12, 14
___12. How would you classify a singleswitch and two ways switch?
a. Number b. Shilled c. Diagram d. Operation
___13. What ideas justify to a number of ampere is mostly use in a bulb and switch?
a. 30 b. 25 c. 20 d. 50
___14. How would you classify three way light?
a. Special switches known as three-way switches c. Special switches known as two-way switches
b. Special switches known as switches d. Special switches known as three-way
___15. How could you determine Special Romex Wire?
a. An external white irealongwithin the sheath
b. An external that has an extra red insulated wire along with the black and white wires within the sheath
c. An external black insulated wirealongwithin the sheath
d. An external that has an extra insulated wire alongwith the black and white wires within the sheath
___16. How would you justify common terminal switch?
a. The "bridge" between the supply c. The "bridge" between the power switch
b. The "bridge" between the power supply d. The bridgeand the power supply
___17. How would you use 3-Way applications?
a. Tag that wirewith electrical tapeand identify as the common in both the dimmer wall box and remote wall box
b. Tag that wirewith electrical tapeand identify as the Load in both the dimmer wall box and remote wall box
c. Tag that wire with electrical tape and identify as the common (Line or Load) in both the dimmer wall box and remote
wall box
d. Tag that wirewith electrical tapeLoad in both the dimmer wall box and remote wall box
___18. How would you use 4-Way applications?
a. Tag that wirewith electrical tapeand identify as the common in both the dimmer wall box and remote wall box
b. Tag that wirewith electrical tapeand identify as the Load in both the dimmer wall box and remote wall box
c. Tag that wirewith electrical tapeand identify as the common (Line or Load) in both the dimmer wall box and remote
wall box
d. Tag the two wires connected to the two back screw terminals
___19. How would you apply what you learned to develop preparingand connecting wires?
a. Side wire terminals accept #14-12 AWG solid copper wire only
b. Back wire openings accept#14-12 AWG solid copper wireonly
c. Side and Back wire terminals accept#14-12 AWG solid copper wireonly
d. None of the above
___20. What would resultif the sidewireconnection is connected?
a. Side Wire Connection b. Back WireConnection c. Side & Back Wire Connection d. All of the above
___21. What is the part of switch that connected to the 3 to 4 way connection?
a. Separate Connection b. Single Connection c. Two way connection d. 3-4 way connection
___22. How would you classify normal switch?
a. Has to terminal that are either connected or disconnected c. Has no connection
b. Has one terminal that are connected of disconnected d. Disconnected
2. ___23. How would you show your understanding of remote mounting?
a. Turn off power at circuit breaker c. Of & On
b. Turn on power at circuitbreaker d. Remounting
___24. What would the resultif there is no connection in switch?
a. Not connected b. Repair c. Connected d. Black out
___25. How would you show your understanding of Lights Flickering?
a. Lamp has a bad connection b. Lamp has a connection c. Lamp is burned out d. All of the Above
___26. How would you test Master dimmer?
a. Position singlewireto provide room in outlet wall box for device
b. Position all wires to provide room in outlet wall box for device
c. Position doublewires to provide room in outlet wall box for device
d. Position does not require to provide room in outlet wall box for device
___27. What is open wiring?
a. Wiringmethod usingcleats, knobs,tubes and flexibletubingfor the connection
b. Wiring method using cleats, knobs, tubes and flexible tubing for the protection
c. Insulated conductors run ,in or on buildings,and concealed by the buildingstructure
d. All of the above
___28. Which one is the answer define by open wiring?
a. Wiringmethod usingcleats,knobs,tubes and flexibletubingfor the connection
b. Wiring method using cleats, knobs, tubes and flexible tubing for the protection
c. Insulated conductors run ,in or on buildings,and concealed by the buildingstructure
d. All of the above
___29. How would you classify Open wiringon insulators shall notbe used EXCEPT?
a. In commercial garages b. In theaters c In motion-picture studios d. House wiring
___30. Which statements support in damp or wet locations?
a. Larger conductors supported on solid knobs
b. Separation of at least 1 inch from the surface wired
c. Separately encased in flexibletubing
d. Position doublewires to provide room in outlet wall box for device
___31. What elements would you choose the 3/8 through 1-1/4 inch trade sizes?
a. Flexiblehost b. Wire gauge c. Cord-packed d. Tool box
___32. How would you use the flexibleinner core?
a. Tool box b. Wood strip c. Wiregauge d. Heavy-gauge
___33. What arethe other parts of AT type used?
a. Used on industrial process equipment c. Designed for hot or cold environments
b. Tool Gray d. PVC
___34. How would you classify ZHLA?
a. Halogen b. Non-halogen c. Low flame spread d. High flame spread
___35. What type of wiringis enclosed in a metallic sheathingand is more resistantto damage than Romex wiring?
a. Romex Wiring b. BX Wiring c. Type UF d. Type TW wire
___36. What elements would you choosenonmetallic,sheathed wiring a type of wiringthatis installed in a house?
a. Romex Wiring b. BX Wiring c. Type UF d. Type TW wire
___37. What is the function of Type UF?
a. The type of wiringthat is installed in a house c. The type covered by heavy plastic sheathing
b. The type of wiringis widely utilized but is less resistant d. None of these
___38. Based on what you know, how would you explain TW wire?
a. Has a thin thermoplastic insulation that provides the wire with some measure of moisture resistance
b. Has a brand name for a type of plasticinsulated wire
c. Has a flexiblealuminumor steel sheath over the conductors and is fairly resistantto damage
d. Has a type of wiringthat is installed in a house
___39. What approach would you use to TECK cablewire?
a. Has a brand name for a type of plasticinsulated wire
b. Has a flexiblealuminumor steel sheath over the conductors and is fairly resistantto damage
c. Protection for cable in concealed locations in wiring
d. Position doublewires to provide room in outlet wall box for device
___40. How would you use the TW wire?
a. To provides the wire with some measure of moisture resistance
b. To covered by heavy plastic sheathing
c. To utilized but is less resistantto damage than BX wiring
d. To utilized but is greater resistantto damage than BX wiring
___41. What is the best answer in this type of plastic insulated wire,sometimes called non-metallicsheath?
a. BX b. UF c. TW d. Romex
3. ___42. Can you identify what is armored cable? Then what is the best answer?
a. BX Cable b. UF Cable c. TW Cable d. Romex Cable
___43. What is the relationship of Electrical Wiringand Cable?
a. Usage b. Common use c. Connection d. Skinning
___44. What is the function of NM in electrical?
a. Non-metallic b. Metallic c. UF d. Romex
___45. How would you explain Access Flooring?
a. A conductor can carry three hours or more without exceeding the temperature rating
b. A flooring system in which modular panels are raised above the floor slab, typically on 3”- to 12”-high supports
c. A planningpracticein which the total amperage requirements of the electrical equipment
d. None of this answer
___46. How would you describeAmpacity?
a. Maximum current b. Minimum current c. Voltage d. Breaker
___47. State in your own words about Load Balancing?
a. Amperage b. Minimum current c. Voltage d. Breaker
___48. What is the main idea of CircuitBreaker?
a. Design for current b. Designed to stop the flow c. Minimum current d. Voltage
___49. What examples can you find to a normal switch?
a. One terminals b. Brass c. Two terminals d. Brass and Green
___50. How would you use singlepoleswitch?
a. Use for Cutting b. Use for wiring c. Use for terminals d. Use for connection
___51. Which of the followingis NOTbelong to 3 way wiring?
a. Nut b. Wire c. Switch d. Utility box
___52. What is your opinion of about three-way lights?
a. One traveler will alwaysbein the same cablewith each other
b. One traveler will alwaysnot the same cablewith each other
c. The two travelers will always notthe same cablewith each other
d. The two travelers will always be in the same cable with each other
___53. How would you classify schematic drawing?
a. The contact points within the switches can route the electricity to the light fixture
b. The contact points without the switches can route the electricity to the lightfixture
c. The contact points within the wires can route the electricity to the lightfixture
d. The contact points within the switches cannotroute the electricity to the lightfixture
___54. What is the function of 4-way switch system?
a. The two travelers will alwaysnotthe same cablewith each other
b. The two travelers will alwaysbein the same cablewith each other
c. A planningpracticein which the total amperage requirements of the electrical equipment
d. The contact points within the switches can route the electricity to the light fixture
___55. How could you determine the 4-way switch system connection?
a. One traveler will alwaysbein the same cablewith each other
b. One traveler will alwaysnotthe same cable with each other
c. The system is often used in staircases to control the lighting at three different levels and in rooms
d. All of the above
___56. What facts can you compile the set-up consists of two 3-way switches and one or more 4-way switches?
a. One traveler will alwaysbein the same cablewith each other
b. One traveler will alwaysnotthe same cablewith each other
c. The system is often used in staircases to control the lightingat three different levels and in rooms
d. The schematic illustrates how the contact points within the switches can route the electricity to the light fixture
___57. How would you apply what you learned to develop simpleand safeto install even under difficultcondition?
a. The rocker is simply snapped into the frame to form a complete single unit
b. The two travelers will alwaysnotthe same cablewith each other
c. The two travelers will alwaysbein the same cablewith each other
d. The rocker is simply snapped into the frame to form a complete double unit
___58. What do you expect of an insert? It goes without sayingthat you want inserts that are easy to mount?
a. All live parts are covered with insulating material for all-round touch protection
b. All one traveler will alwaysbein the same cablewith each other
c. All one traveler will alwaysnotthe same cablewith each other
d. All of the above
___59. What evidence can you find the compact insert?
a. Male plug b. Mounted securely c. Inserted led d. Out-let
___60. What way would you design for the protection of the lightning?
a. Breaker b. Live wire c. Ground wire d. Antenna
___61. What examples can you find to “apprehension “under the ECP?
a. Establishment b. Roll out c. Code d. System
___62. How would you classify Restriction on the Issuance of Restraining Orders or Writs of Injunction?
4. a. Establishment b. Prima facie c. Code d. System
___63. How would you categorize Act punishableunder RA 7832?
a. System Code b. Prima facie c. Section code d. PEC
___64. What is the function of Act punishableunder RA 7832?
a. An act penalizing the pilferage of electricity and theft of electric power transmission lines/materials, rationalizing
system losses by phasing out pilferage losses as a component thereofand for other purposes
b. An actpenalizingthe pilferageof electricity and transmission lines/materials,rationalizing systemlosses by phasingout
pilferagelosses as a component thereof and for other purposes
c. An actpenalizingthe pilferageof electricity and theft losses by phasingoutpilferagelosses asa component thereof and
for other purposes
d. All of the above
___65. How would you describeERN?
a. Electricity Regulatory Board b. Energy Regulatory Board c. Electrical Regulatory Board d. None of these
___66. What is Differential billing in PEC?
a. An actpenalizingthe pilferageof electricity and transmission lines/materials,rationalizingsystemlosses by phasingout
pilferagelosses as a component thereof and for other purposes
b. An actpenalizingthe pilferageof electricity and theft losses by phasingoutpilferagelosses asa component thereof and
for other purposes
c. The amount to be charged to the person concerned for the unbilled electricity illegally consumed as determined
through the use of methodologies outlined in Section 6 of R.A. 7832
d. All of the above
___67. What can you say about"NPC"?
a. National Power Coordination b. National Power Coop c. National Power Commercial d. National Power Corporation
___68. State in your own words about DOE?
a. Department of Energy b. Department of Electricity c. Department of Environment d. None of these
___69. How would you apply what you learned to develop Cooperative?
a. Rural Electric Cooperative c. Rural Electric Coop
b. Rural Electricity Cooperative d. Urban Electric Cooperative
___70. Which ones is correctdefinition of Differential billing?
a. An actpenalizingthe pilferageof electricity and transmission lines/materials,rationalizingsystemlosses by phasingout
pilferagelosses as a component thereof and for other purposes
b. An actpenalizingthe pilferageof electricity and theft losses by phasingoutpilferagelosses asa component thereof and
for other purposes
c. The amount to be charged to the person concerned for the unbilled electricity illegally consumed as determined
through the use of methodologies outlined in Section 6 of R.A. 7832
d. All of the above
___71. What can you say about Apprehension of PEC?
a. The discovery of the presence of any of circumstances enumerated in Section 4 of R.A. No. 7832 in the establishment
or outfit of the consumer concerned as personally witnessed and attested to by the consumer concerned or a duly
authorized ERB
b. The presence of any of circumstances enumerated in Section 4 of R.A. No. 7832 in the establishmentor outfit of the
consumer concerned as personally witnessed and attested to by the consumer concerned or a duly authorized ERB
c. An actpenalizingthe pilferageof electricity and transmission lines/materials,rationalizingsystemlosses by phasingout
pilferagelosses as a component thereof and for other purposes
d. An actpenalizingthe pilferageof electricity and theft losses by phasingoutpilferagelosses asa component thereof and
for other purposes
___72. Which the best answer of the latestmonthly bill served by the utility or cooperativewhich does not include any period
before the time of apprehension?
a. Bill b. Partial Bill c. Current Bill d. Payment
___73. What is PEC in NER?
a. Philippines Electrical Code c. Philippines Electrical Cooperation
b. Philippines Electrical Current d. All of the above
___74. Which one rule section about the Anti-Pilferageof Electricity and Theft of Electric Transmission Lines/MaterialsActof
1994?
a. Section 2 b. Section 3 c. Section 1 d. Section 4
___75. What can you say about section 2 in rule 1?
a. Title b. Construction c. Terms d. Definition
___76. What is the main idea of Current Rate?
a. The two travelers will alwaysnotthe same cablewith each other
b. The two travelers will alwaysbein the same cablewith each other
c. The total rate of electricity per kilowatt-hour as reflected in the current bill
d. The average rate of electricity per kilowatt-hour as reflected in the current bill
___77. How would you apply what you learned to develop NATURE OF VIOLATION of 90/275?
a. Fine of not more than P1, 000 or imprisonment of not more than 6 months, or both. (Sec. 275, NIRC)
5. b. Fine of not more than P2, 000 or imprisonment of not more than 6 months, or both. (Sec. 275, NIRC)
c. Fine of not more than P1, 000 or imprisonment of not more than 5 months, or both. (Sec. 275, NIRC)
d. Fine of not more than P2, 000 or imprisonment of not more than 5 months, or both. (Sec. 275, NIRC)
___78. What would resultif a failureto keep/preserve records required by lawor regulations?
a. CRIMINAL PENALTY IMPOSED c. CODE SECTION
b. NATURE OF VIOLATION d. NONE OF THESE
___79. How would you classify thepayment of REVISED SCHEDULE OF COMPROMISE PENALTY?
a. Criminal penalty imposed c. Code section
b. Nature of violation d. Amount of compromise
___80. What is the function of CRIMINAL PENALTY IMPOSED to the Failureto Pay & Display theAnnual Registration Fee (BIR Form
0605)?
a. Fine of not more than 1,000 or imprisonment of not more than 6 months (Sec. 275, NIRC)
b. Fine of not more than 1,000 or imprisonment of not more than 10 months (Sec. 275, NIRC)
c. Fine of not more than 5,000 or imprisonment of not more than 6 months (Sec. 275,NIRC)
d. Fine of not more than 1,000 or imprisonment of not more than 7 months (Sec. 275,NIRC)