3. 赛宏生产有3种不同温度、材料的高温滚筒,针对铝型材挤出来过程中出现的不同的温度和输送。
SAIHONG FELT manufactures 3 different material and temperatures of rollers optimised for the different
and variable alpplication areas occuring in your extrusion process.
超高温 PBO 滚筒
* 耐温 600℃。
* 表面为 100%PBO 纤维组成,
底部高温层
为 100%Kevlar 组成。
* 适用于出料口使用。
* 完美代替石墨,
杜绝石墨印。
PBO/KVLAR ROLLER
* Temperature resistant up to 600℃ .
* Consisting of 100% PBO fiber on the top
and 100% Kevlar fiber at the bottom.
* Application for the aluminium exrusion exit.
* Perectly replacement of graphite, to void the
black mark and the damage from the graphite.
黄色高温滚筒
* 耐温 480℃。
* 由 100%Kevlar 组成。
* 适用于滑出台使用。
KEVLAR ROLLER
* Temperature resistant up to 480 ° C.
* Consisting of 100% Kevlar.
* Application for run out table.
低温滚筒
* 耐温 180℃。
* 适用于成品锯台使用。
Low temperature roller
* Temperature resistant up to 180 °C.
* Suitable for finished cutting table.
滚筒的优点
1. 赛宏毛毡滚筒采用创新的硬化处理工艺,
处理后的毛毡整体感觉较硬,
但表面保持柔软,
能更好保护铝材表面,
受热不会污染铝材或刮花铝型材。
2. 赛宏滚筒内径和铝筒外径一致,在整个传动期间保持一致,防止铝材出现变形,损坏。
3. 赛宏毡筒创新的生产工艺,保证生产出的产品 ID 公差在 -0+0.15mm, 从而达到完美配合,更易于安装。
4. 赛宏滚筒创新的生产工艺,可以最大限度地将热量传导到钢滚筒或铝滚筒上,从而延长滚筒使用寿命。
FELT ROLLER ADVANTAGES
1. Due to our roller with an innovative resin treatment. After resin treated felt feels hard overall, but the surface remains soft and provoide better
protecttion of the aluminum finishes, no sticky on the hot aluminium profiles , no damage and scratched aluminum profiles.
2. The inner diameter of the SAIHONG FELT ROLLER is the same as the outer diameter of the aluminum roller. The felt roller perfectly match the
metal roller, during the transmission to prevent deformation and dent of the aluminium profile.
3. The innovative production process of SAIHONG FELT roller ensures that the roller ID tolerance is -0+0.15mm, which is a perfect fit and easier to
install.
4. SAIHONG innovative production process, maximizes conduction heat from the felt roller to metal roller, giving a better life span of the felt roller.
SAIHONG ROLLER SLEEVES
赛宏滚筒 /
产 品 展 示 图
PRODUCT DEMONSTRATION CHART
SAIHONG
03 04
4. 赛宏环形输送带 /
SAIHONG ENDLESS CONVEYOR BELTS
超高温 PBO 环形输送带
* 耐温 600℃。
* 适用于一、
二级冷床使用。
PBO/KEVLAR ENDLESS BELT
* Temperature resistant up to 600 ° C.
* Suitable for run out table and cooling table.
高温环形输送带
* 耐温 480℃。
* 适用于一、
二级冷床使用。
KEVLAR ENDLESS ENDLESS
BELT(HIGH TEMP.)
* Temperature resistant up to480 ° C.
* Suitable for run out table and cooling table.
中温环型输送带
* 耐温 280℃。
* 适用于拉直机后面使用。
NOMEX ENDLESS BELT
* Temperature resistant up to 280 ° C.
* Suitable for stretcher, finishing and batching
table.
低温环型输送带
* 耐温 180℃。
* 适用于常温区使用
(如:
包装台,
喷涂上下线,
氧化上下线)
。
LOWER TEMPEATURE
ENDESS BELT
* Temperature resistant 180 °C.
* Application for room temperature zone
conveyor (eg: packaging table, painting line
of uploading and off loading, uploading and
off loading of Anodizing lines).
皮带特点
1. 赛宏毛毡皮带,采用创新的硬化工艺,整体感觉很硬表面又很柔软,即提高了使用寿命,又没有传统工艺产生的皮带印迹。
2. 凯夫拉(Kevlar) 断裂伸长率为 2.4%,为了给皮带最大的拉伸强度,赛宏采用了凯夫拉长丝编织的基布作支撑,然后针刺让环带支撑层达到
小于 1% 延伸力。
3. 经过测试,赛宏毛毡环带两侧输送均匀,对铝梁的摩擦力减少 30%,对驱动皮带轮的抱合力提高 40%
皮带加硬
在铝型材冷却、输送期间皮带加硬可以防止掉毛、脱皮现象。
经济实用
因为我们皮带在驱动皮带轮上具有很好的抱合力,和吕梁有非常低的摩擦力,所以即使在其上面有大量的很重、很大型的铝材,皮带与皮带轮也
有非常好的张力,不用担心环带打滑,不够拉力。节省并优化皮带的使用寿命。
切割
对于皮带的直线运动,切割过程非常重要。在切割过程中赛宏皮带必须保持平衡,确保 100%直线切割,保证皮带在冷床输送线上使用不跑偏。
BELT CHARACTERISTICS
1. SAIHONG FLT belt, using innovative resin treatment process, the overall feel is very hard, the surface are soft, that is to improve the service life, and
there is no belt sticky caused on the aluminium surface. No scratch or dents to the aluminium finishes, totally different from the the traditional process.
2. Kevlar has an elongation at break of 2.4%. in order to give the belt the maximum tensile strength, SAIHONG is using a Para Aramid(kevlar)
textile scrim which is needle punched to an endless support layer with no stretch, allows the endless support layer (the scrim) to reach less than 1%
elongation.
3. After testing, hard edges on the driving both sides , reducing the friction of the aluminum arm by 30% and 40% more grrip on the driving pulley.
Straight running back and forwarding during operation.
BELT IMPRENATION(RESIN TREATMENT)
Hard side can prevent the belts from getting astray and peeling, in case of shrinkage of the aluminium profiles during the cool-off period, forcing the
belts to the sides of the arm.
Economical and practical
Because SAIHONG belt have much better grip on the driving pulley and low friction on the arm the belts are put under less tension in comparision with
others even with a lof of aluminium weight on tip of them. Saving engery and optimising the lifetime of the belt.
CUTTING
The cutting process is exceptional important for a straight run of the belts. Before the cutting process start SAIHONG belt are balanced out, assuring a
100% straight cut which gurantees a straight run of the belts bak and forward on the conveyor systems.
产 品 展 示 图
PRODUCT DEMONSTRATION CHART
SAIHONG
05 06
5. 同步带
* 可定做所有国际齿型。
* 可定做高温
(500°C)
、
中温
(280°C)
、
低温
(180°C)的毛毡进行粘合。
SYNCHRONOUS TIMING BELT
* All international tooth types can be
customized.
* Can be customized for high temperature
(500 ° C), medium temperature (280 ° C),
Low temperature (180 ° C)
* High temp. felts are well glued with timing
belt, no separation in the glue. The timing
teeth are perfectly matched the timing
teeth.
开口带
* 可定做各种温度的开口带。
* 用于不方便拆卸的冷床,
方便安装。
BELT WITH JOINT, WITH CLIP
*Can be customized with a variety of
temperature openings join belts
*Application for the old cooling systems
which is not convenient to disassemble,
easy for installtion.
PBO 毡块
* 耐温 600℃。
* 完全替代出料口石墨,
防止墨印的产生。
PBO FELT PAD
* Temperature resistance 600 ° C.
* Complete instead of the graphite in the exit of
extrusion, to prevent graphite marks
低温毛毡套
* 耐温 180℃。
* 适用于喷涂车间、
氧化车间隔料使用。
LOW TEMPERATURE
FELT COVER
* Temperature resistant 180 °C.
* Suitable for painting and anodizing
workshop.
时效炉毛毡套
* 耐温 280℃。
* 适用于挤压车间
AGING FURNACE FELT COVER
(SPACER SLEEVE)
* Temperature resistant 280 ° C.
* Suitable for aging oven
时效炉框架料
* 耐温 280℃。
* 防止时效炉框刮伤型材。
FELT STRIP FOR AGING
FURNACE BASKET
* Temperature resistant 280 ° C.
* Prevent basket damage to the profiles
during the transportation
产 品 展 示 图
PRODUCT DEMONSTRATION CHART
SAIHONG
08
07
6. 09
产 品 生 产 流 程
PRODUCT PRODUCTION PROCESS
SAIHONG
10
7. 手机 ( 国内 ): 13927710149
电话 : 0757-86406674
传真:
0757-86406012
地址:
广东省佛山市南海区罗村联和
工业区东区十六路 5-2 号
INTERNATIONAL ( 国际 )
CELL PHONE:
+86 13927758681 (FRANK LEE)
E-mail: fsaihong@163.com
Address: No.5-2 East zone, Lianhe Industrial zone,
Luo cun, Nahai,Foshan, China 528200
佛山市南海区赛宏毡业有限公司
FOSHAN SAIHONG FELT CO.,LTD.
采用优质纤维制造(PBO / KEVLAR / NOMEX/PE)
Manufactured out ofthe purest high quality fiber in world
(PBO/KEVLAR/NOMEX/PE)