1. POWER ELECTRONICS
S.No
CODE
PROJECT TITLE
1
ET13P
E1
Voltage-Based Control of a Smart Transformer in a
Micro grid
For the islanded operation of a micro grid, several control
strategies have been developed. For example, voltage based
droop control can be implemented for the active power
control of the generators & the control of the active loads.
Novel High Step-Up DC–DC Converter for Distributed
Generation System
In this paper, a novel high step-up dc–dc converter for
distributed generation systems is proposed. Concept is to
utilize two capacitors & one coupled inductor. The two
capacitors are charged in parallel during the switch-off
period and are discharged in series during the switch-on
period by the energy stored in the coupled inductor to
achieve a high step-up voltage gain.
Maximum Power Point Tracking Technique for Partially
Shaded Photovoltaic Systems in Micro grids
A modified fuzzy-logic controller for maximum power
point (MPP) tracking is proposed to increase photovoltaic
(PV) system performance during partially shaded
conditions. Instead of perturbing and observing the PV
system MPP, the controller scans and stores the maximum
power during the perturbing and observing procedures.
Digital Control for an ArcWelding Machine Based on
Resonant Converters and Synchronous Rectification
This paper presents a optimized drive signals for resonant
converters using synchronous rectification (SR) applied to
an arc welding machine.
DESCRIPTION
2
ET13P
E2
DESCRIPTION
3
ET13P
E3
DESCRIPTION
4
ET13P
E4
DESCRIPTION
5
ET13P
E5
An Energy-Stored Quasi-Z-Source Inverter for
Application to Photovoltaic Power System
This paper proposes a new topology of the energy-stored

2. DESCRIPTION
6
ET13P
E6
DESCRIPTION
7
ET13P
E7
DESCRIPTION
8
ET13P
E8
DESCRIPTION
9
ET13P
E9
DESCRIPTION
10
ET13P
E10
qZSI. The operating characteristic of the proposed
solution is analyzed in detail. 2-strategies are proposed
with the related design principles to control the new
energy-stored qZSI when applied to the PV power system.
Battery Charger for Electric Vehicle Traction Battery
Switch Station
This paper presents the functionality of a commercialized
fast charger for a lithium-ion electric vehicle propulsion
battery. The device is intended to operate in a battery
switch station, allowing an up-to 1-h recharge of a 25kWh depleted battery.
Bifurcation Analysis of Standalone Photovoltaic- Battery
Hybrid Power System
Standalone photovoltaic-battery hybrid power systems are
attractive renewable power generation systems, a popular
form of which is based on a photovoltaic system and a
battery connected to an output dc bus via a buck converter
& a bidirectional buck/boost converter.
Boost rectifier using single phase matrix converter with
reduced switch counts
This paper focuses on implementation of computer
simulation for boost rectifier operation using single-phase
matrix converter topology with reduced switch counts.
Proposed topology employed only six switches compared
with the conventional boost rectifier operation using single
phase matrix converter topology used eight main switches.
New Extendable Single-Stage Multi-Input DC-DC/AC
Boost Converter
This paper presents a new extendable single-stage multiinput DC-DC/AC boost converter. The proposed
structure comprises two bidirectional ports in the
converter central part to interface output load and battery
storage, and several unidirectional input ports to get
powers from different input dc sources.
A Modified Single-Phase Quasi-Z-Source AC–AC
Converter

3. DESCRIPTION
11
ET13P
E11
DESCRIPTION
12
ET13P
E12
DESCRIPTION
13
ET13P
E13
DESCRIPTION
14
ET13P
E14
DESCRIPTION
15
ET13P
E15
A modified single-phase quasi-Z-source ac–ac converter is
proposed in this paper. Proposed converter has the main
features in that the O/P voltage can be bucked or boosted
and be both in-phase& out-of-phase with the I/P voltage
Highly Efficient Analog Maximum Power Point
Tracking (AMPPT) in a Photovoltaic System
Compact-size analog maximum power point tracking
(AMPPT) technique is proposed in this paper for high
power efficiency in the photovoltaic (PV) system.
Combining existing MPPT approaches, we present a fast
& accurate tracking performance.
A New Cascaded Multilevel Inverter with
Reduced Number of Switches
This paper propose a new topology for cascaded multilevel
inverters. This structure consists of series connection of
proposed basic unit blocks which are built with both
unidirectional and bidirectional switches.
Boost-Derived Hybrid Converter with simultaneous DC
and AC outputs
The paper proposes a family of hybrid converter topologies
which can supply simultaneous DC as well as AC loads
from a single DC input. These topologies are realized by
replacing the controlled switch of single-switch boost
converters with a voltage source inverter (VSI) bridge
network.
Flexible Multilevel Boost DC-AC Converter
In this paper, incorporation of MULTI-output boost
(MOB) converter by multilevel inverter is proposed.
Renewable energy sources such as fuel cell and
photovoltaic produce low level of voltage. So to increase
the magnitude of voltage, dc-dc boost converter is used.
Improved ZVS DC-DC Converter With a High Voltage
Gain and a Ripple-Free Input Current

4. DESCRIPTION
16
ET13P
E16
DESCRIPTION
17
ET13P
E17
DESCRIPTION
18
ET13P
E18
DESCRIPTION
An improved zero-voltage-switching (ZVS) dc-dc
converter with high voltage gain & ripple-free I/P current
is proposed. It consists two converter cellsa boost cell and
an asymmetrical pulse-width-modulation (APWM) fullbridge cell. Boost cell in the proposed converter has
capabilities of providing a ripple-free i/p current.
A Soft Switching Three-phase Current-fed Bidirectional
DC-DC Converter With High Efficiency Over a Wide
Input Voltage Range
In this paper, a three-phase current-fed dual-activebridge
(DAB) bidirectional DC-DC converter is presented.
Compared to the voltage source DAB converter, the
proposed converter allows low RMS current and maintains
zero voltage switching (ZVS) in the whole operating range
by keeping the ratio between primary side and secondary
side DC-link voltage constant, leading to high efficient
energy conversion over a wide input voltage range.
Cascade Three-Level AC/AC Direct Converter
This paper proposes a novel family of cascade threelevel
(TL) ac–ac direct converters based on ac switch cells,
which transfer unsteady high ac voltage with distortion
into regulated sinusoidal voltage with low total harmonic
distortion (THD).
Grid-Connected Boost-Half-Bridge Photovoltaic
Microinverter System Using Repetitive Current Control
and Maximum Power Point Tracking
This paper presents a novel grid-connected boost halfbridge photovoltaic (PV) micro inverter system and its
control implementations. In order to achieve low cost, easy
control, high efficiency, and high reliability, a boost-halfbridge dc–dc converter using minimal devices is
introduced to interface the low-voltage PV module.

5. 19
ET13P
E19
DESCRIPTION
20
ET13P
E20
DESCRIPTION
Novel Zeta-Mode Three-Level AC Direct Converter
An improved zero-voltage-switching (ZVS) dc-dc
converter with a high voltage gain and a ripple-free input
current is proposed. It consists of two converter cells—a
boost cell and an asymmetrical pulse-width-modulation
(APWM) full-bridge cell. Boost cell in proposed converter
has capabilities of providing ripple-free I/p current.
Step-Up DC/DC Converters With Cascaded Quasi-ZSource Network
The proposed cascaded qZSI inherits all the advantages of
the traditional solution .Moreover, as compared to the
conventional qZSI, the proposed solution reduces the
shoot-through duty cycle by over 30% at the same voltage
boost factor.
POWER SYSTEM
S.No
1
CODE
ET13P
S1
DESCRIPTION
2
ET13P
S2
DESCRIPTION
3
ET13P
S3
PROJECT TITLE
Improvement of power quality by using hybrid fuzzy
controlled based IPQC at various load conditions
This paper presents a hybrid fuzzy logic controlled based
improved power quality conditioner used to
counterbalance for harmonic distortion in 3-phase system.
A Method for Evaluating Energy Efficiency to Justify
Power Factor Correction in Ship Power Systems
This paper presents the methodology and results for the
economic evaluation of PFC in marine vessels. A
mathematical model, used to determine the relationships
among fuel oil consumption, emission and power factor
for the diesel electric generator, is derived to quantify the
possible benefits with PFC.
Reactive Power Compensation in Single-Phase
Operation of Microgrid

6. DESCRIPTION
4
ET13P
S4
DESCRIPTION
5
ET13P
S5
DESCRIPTION
6
ET13P
S6
DESCRIPTION
7
ET13P
S7
DESCRIPTION
A coordinated control of distributed generators (DG) and
distribution static compensator (DSTATCOM) in a micro
grid is proposed in this paper. With high penetration of
distributed sources and single-phase operation of the
system, voltage unbalance can often go beyond the
acceptable limit.
Technique to Develop Auto Load Shedding &
Islanding Scheme to Prevent Power System Blackout
Abnormal condition in a power system generally leads to a
fall in system frequency, and it leads to system blackout in
an extreme condition. This paper presents a technique to
develop an auto load shedding and islanding scheme for a
power system to prevent blackout and to stabilize the
system under any abnormal condition.
Stabilty Of Power Transmission Capability Of Hvdc
System Using Facts Controllers
a desired power condition at the given points are best
achieved using power controllers such as the well known
High Voltage Direct Current (HVDC) and Flexible
Alternating Current Transmission System (FACTS)
devices.
Multi objective Optimal Location of FACTS ShuntSeries Controllers for Power System Operation Planning
This paper develops appropriate models of flexible AC
transmission systems (FACTS) shunt-series controllers for
multiobjective optimization and also presents a
multiobjective optimization methodology to find the
optimal location of FACTS shunt-series controllers.
Investigation of Domestic Load Control to Provide
Primary Frequency Response Using Smart Meters
The ability of smart meters to control domestic
demand during system emergencies was investigated. In
ths project load control scheme that used a local frequency
measurement from the smart meters was investigated.
POWER SECTORS
S.No
CODE
PROJECT TITLE

7. 1
ET13P
T1
DESCRIPTION
2
ET13P
T2
DESCRIPTION
3
ET13P
T3
DESCRIPTION
4
ET13P
T4
DESCRIPTION
5
ET13P
T5
DESCRIPTION
Computer based Boiler Feed Pump protection and
changeover scheme
The Aim of this project is for protecting the Boiler Feed
Pump failure and using a changeover scheme by
monitoring the required parameters using pc for the
continuous power generation.
Incapability of analog relay protection to detect generator
stator winding ground failures at neutral end
The electromechanical ground protection relay 59GN
commonly used in generator protection does not respond
to grounds in the bottom ~5% of the stator winding. this
paper will describe newer ground relay systems that
monitor and protect the entire stator winding for grounds.
Self-adaptive transformer differential protection
Setting the pickup current and slope of differential
relays of power transformer protection is a well-known
compromise. It has been the focus of study to improve
both the security and sensitivity of transformer differential
protection recently. Therefore a novel adaptive protection
criterion is proposed in this study,
Application of computer and modern automation system
for protection and optimum use of High voltage power
transformer
In this paper an attempt has been made to elaborate
the use of computer and modern automation system for
protection and optimum use of High voltage power
transformer, its advantages and cost effectiveness.
Programmable logic controllers (PLC) can be used for
control & automation of High voltage power transformer.
Switching and protection of multiple transformer
arrangement in industrial distribution system
In modern industrial electrical distributions,
medium size transformers require protection systems that
are faster, more reliable and selective than the systems used
for their earlier counterparts. To achieve such improved

8. performance, this system is used
6
ET13P
T6
DESCRIPTION
7
ET13P
T7
DESCRIPTION
8
ET13P
T8
DESCRIPTION
9
ET13P
T9
Research on the intelligent protection system of coal
conveyor belt
A sort of intelligent protection system for conveyor belt
was designed, which mainly aimed at the phenomenon
of belt slipped, belt broken, overloaded and coupling
broken etc. It was designed by using intelligent
instrument, monitoring software and fault detection
technology, The protection system can automatically
detect, diagnose corresponding fault, and give alarm
signal with sound and light to stop the fault belt machine
in due course. The application effect has proved that the
protection system can improve intelligent degree of the
whole burning coal transport and reduce the manual
greatly and save a lot of funds for enterprise
An Adaptive Fuzzy Mho Relay for Phase Backup
Protection With Infeed From STATCOM
This paper presents a fuzzy-logic-based scheme
for the operation of generator-phase backup distance
protection, otherwise popularly known as “phase 21”
function, in the presence of a STATCOM installed at the
generator bus.
Impact of Power System Instability on Generator
Protection
This paper discusses what relay engineers need to know
about power system stability, including the four basic
types of power system instability. Voltage instability,
Steady-state instability, Transient instability &Dynamic
instability.
Research on the intelligent protection system of coal
conveyor belt

9. DESCRIPTION
10
ET13P
T10
DESCRIPTION
11
ET13P
T11
DESCRIPTION
12
ET13P
T12
DESCRIPTION
13
ET13P
T13
DESCRIPTION
14
ET13P
T14
DESCRIPTION
A sort of intelligent protection system for
conveyor belt was designed, which mainly aimed at the
phenomenon of belt slipped, belt broken, overloaded and
coupling broken etc. The protection system can
automatically detect, diagnose corresponding fault, and
give alarm signal with sound and light to stop the fault
belt machine in due course.
Modeling and Simulation of Digital Frequency Relay for
Generator Protection
This paper presents the design and various data
conversion steps of a digital frequency relay. The designed
relay will cover both over and under frequency conditions.
Modeling and Simulation of Digital Negative Sequence
Relay for Unbalanced Protection of Generator
This paper presents design & various data conversion steps
of a digital negative sequence relay.
Modeling and Simulation of Reverse Power Relay for
Generator Protection
The paper has presented the modeling of digital reverse
power relays
Protection of Transformer-Ended Feeders Using
Multifunction Relays
In this paper, we describe an application of digital
multifunction relays for the protection of a feeder that
ends with a distribution transformer. In this application,
we attempt to provide as many protection functions as
possible with fewest relays.
A Novel Adaptive Dispersed Phase Current Differential
Protection Criterion
A novel adaptive dispersed phase current differential
protection criterion is proposed in this paper, and an
objective function with the independent variable of fault
current component and through current is defined to
revise the restraining ratio of differential protection
criterion adaptively.

10. 15
ET13P
T15
DESCRIPTION
16
ET13P
T16
DESCRIPTION
17
ET13P
T17
DESCRIPTION
18
ET13P
T18
DESCRIPTION
19
ET13P
T19
DESCRIPTION
20
ET13P
T20
Analysis and Solutions of Overcurrent Protection Issues
in a Micro grid
In this project The changes cause detrimental
effect of sympathetic tripping, blinding of protection, relay
over-reaching, relay under-reaching and loss of selectivity
of the over current protection scheme of generators in
micro grid are discussed
Adaptive Differential Protection for Power Transformer
Based on Transient Signal Analysis
This paper presents an adaptive relaying scheme for
percentage differential protection of 3-phase power
transformers.
A New Algorithm to Avoid Maloperation of Transformer
(TFr) Differential Protection in Substations With an
Inner Bridge Connection
This paper analyzes the factors that may lead to the
maloperation of transformer differential protection and
concludes that local transient saturation of the current TFr
(CT) caused by the decaying dc component in the
magnetizing inrush is the main cause of the maloperation
of the TFr differential protection.
A Real Time DSP based Differential Protection of Low
Voltage Bus bar
This paper presents design, implementation and
testing of low voltage bus bar relaying scheme in
laboratory environment using A Digital Signal Processor.
Application of Intelligent Relays to the Islanding
protection of Multiple Synchronous Generators
This article illustrates how intelligent relays can be used to
address DG islanding detection issues spawned by the
presence of more than one synchronous generator on a
distribution feeder.
A Secure Generator Distance Phase Backup Protection
Setting for Enhancing Generator Over excitation
Thermal Capability during System Disturbances

11. DESCRIPTION
In this paper, investigations are carried out to explore the
impact of generator distance phase backup protection
(Relay (21) on the generator over excitation thermal
capability.
EMBEDDED & Robotics
S.No
1
CODE
ET13E
M1
DESCRIPTION
2
ET13E
M2
DESCRIPTION
3
ET13E
M3
DESCRIPTION
4
ET13E
M4
DESCRIPTION
PROJECT TITLE
A System for Mobile Assisted Living
The system can detect abnormal situations with the person
wearing
the
wearable
part
of
the system (e.g. abnormal heart rate) and send this
information to the nursing home so that appropriate
action can be taken immediately.
Wireless remote monitor and control system based on
Zigbee and web
Considering the present development trend of intelligence,
convenience and remoteness in equipment monitoring
area, our system employs intelligent sensors based on
ZigBee wireless communication technology and executable
elements, which is integrated with web applications based
on network environment is introduced in this project
Low cost smart power metering
in this paper a low cost solution for the real-time energy
management in a smart grid, is presented. It provides
several smart meters, which act as slaves, that continuously
monitor connected loads communicating with data
aggregator via CAN-bus.
Remote-Control System of High Efficiency and
Intelligent Street Lighting Using a ZigBee Network of
Devices and Sensors
The proposed remote-control system can optimize
management and efficiency of street lighting systems. It
uses ZigBee-based wireless devices which enable more
efficient street lamp-system management,

12. 5
ET13E
M5
DESCRIPTION
6
ET13E
M6
DESCRIPTION
7
ET13E
M7
DESCRIPTION
8
ET13E
M8
DESCRIPTION
9
ET13E
M9
Automatic speed and torque monitoring in induction
motors using ZigBee and SMS
This project is for monitoring the speed and torque in
induction motors in real time by employing ZigBee based
wireless sensor network. The values calculated by the
embedded system are transmitted to a monitoring unit
through ZigBee based wireless sensor network.
A RISC Microcontroller Based Voltage Regulator
Module with Fuzzy Logic Controller for Processor Core
in Mobile Systems
This paper describes the design of Buck converter that has
a fuzzy controller implemented using a RISC based
microcontroller from Atmel series along with a choice of
hardware components that will ensure better efficiency
while delivering good stability and a dynamic response
that complies with requirements of the target processor.
Advanced Virtual Embedded System Laboratory
In this virtual web based laboratory a student can perform
experiments, simulations and experimental validation of
results virtually using a single PC.
A low cost web based remote monitoring system with
built-in security feature for vulnerable environments
This paper mainly focus on the design and
implementation of an intelligent, low cost and fully
automated system which will be able to provide full time
monitoring and eventual security to susceptible
environment like gas filling station, research and
development laboratories etc.
Automatic Control for Laboratory Sterilization Process
based on Arduino Hardware

13. DESCRIPTION
10
ET13E
M10
DESCRIPTION
11
ET13E
M11
DESCRIPTION
12
ET13E
M12
DESCRIPTION
13
ET13E
M13
DESCRIPTION
14
ET13R
O1
In this paper An automated control system for the
sterilization process of biological material is introduced.
The proposed system is composed of four modules: flame
detection, pressure sensor, Gas Control Module and CPU
Module. This System is based on Arduino Board.
Online Control of Fuzzy Based Mine Detecting Robot
Using Virtual Instrumentation
In the real time applications detection & location of bomb
is highly essential in the field of defense applications. This
paper proposes the design of a micro-controller based
fuzzy logic controller for a remote controlled mine
detecting robot.
Design and Conceptual Development of a Sunbathe
Laundry Robot
The main objective of this project is to design and develop
a prototype that base on light detection sensor and water
detection circuit with both parameters interface with twin
motor gearbox for movement purpose.
Design and Implementation of Industrial Network
Monitoring Protocol for Networked Industrial Sensors
in this project a Industrial Network Monitoring Protocol
is proposed. the proposed protocol provides device
message sets. For maintainability, it provides the fault
detection and reporting. For the user’s convenience, it
provides a categorized addressing system.
Automatic Measurement and Reporting System of Water
Quality Based on GSM
The system consists of multiple sensors of water quality
testing, single-chip microcontroller data acquisition
module, information transmission module, monitoring
center and other Accessories. Various parameters of water
quality are automatically detected and the data are
instantaneously sent to monitoring center by GSM
network in the form of SMS.
Developing a 32-bit microcontroller board for embedded
applications

14. DESCRIPTION
15
ET13R
O2
DESCRIPTION
This paper describes development of a 32-bit embedded
microcontroller board intended for a broad range of
applications.
Online control of remote operated agricultural Robot
using Fuzzy Controller and Virtual Instrumentation
This paper details the design of a micro-controller based
fuzzy logic controller for an agricultural Robot which can
be used for plugging, seeding and soil moisture sensing.
LABVIEW
S.No
CODE
PROJECT TITLE
1
ET13L
V1
Online control of remote operated agricultural Robot
using Fuzzy Controller and Virtual Instrumentation
DESCRIPTION
2
ET13L
V2
DESCRIPTION
3
ET13L
V3
DESCRIPTION
4
ET13L
V4
This paper details the design of a micro-controller based
fuzzy logic controller for an agricultural Robot which can
be used for ploughing, seeding and soil moisture sensing
Virtual Lab: Remote Access and Speed Control of DC
Motor using Ward-Leonard System
The objective of this project is to demonstrate the realtime web based laboratory experiment conduction by
accessing the laboratory set-up from a remote location and
measure the experimental parameters by generating the
control commands at a distant client.
The Design of ZigBee Protocol Based Mobile Node in
Wireless Sensor Network
In order to overcome the defects of static wireless
sensor network nodes, such as poor adaptability,
communication disruption, lack of dynamic network & so
on, a kind of approach to design mobile wireless sensor
node is proposed in this paper.
Remote Monitoring and Controlling of Gas Sensors
Using VPN Connection

15. DESCRIPTION
5
ET13L
V5
DESCRIPTION
6
ET13L
V6
DESCRIPTION
7
ET13L
V7
DESCRIPTION
8
ET13L
V8
DESCRIPTION
9
ET13L
V9
The use of sensors is witnessing a dramatic increase. They
are applied in diverse fields such as military, industrial,
health, and smart homes. Monitoring these sensors could
be made remotely with the help of communication
networks. Using Labview
Oxygen Level Monitoring in an Oxygen Cylinder
The amount of oxygen present inside the cylinder is
measured by the pressure at the outlet nozzle. The pressure
is measured using a high precision MEMS Pressure Sensor
& displayed in Labview.
Experiential Learning of Digital Communication Using
LabVIEW
. This paper discusses the design & implementation of
laboratories and course projects using Labview in
instrumentation course. Pedagogical challenge is to
enhance students’ learning of digital communication using
LabVIEW.
Data Acquisition and Realization of Communication
Transmission Based on Labview
Through the Internet we can make the virtual experiments
platform published on the web, sharing resources and
avoid duplication of equipment purchased and waste of
resources. A lot of data acquisition and wireless
communication framework was developed based on
graphic programming platform of Labview.
Novel Design Solutions for Remote Access, Acquire and
Control of Laboratory Experiments on DC Machines
This paper presents the novel design techniques
to access experiments on electrical machines remotely
through the Web using virtual instrumentation (VI) tools.
LabVIEW Based Automatic Paralleling of Synchronous
Generator System

16. DESCRIPTION
10
ET13L
V10
DESCRIPTION
This paper describes the development &
implementation of automatic paralleling of synchronous
generator system using Labview platform.
Online Control of Fuzzy Based Mine Detecting Robot
Using Virtual Instrumentation
In the real time applications the detection and
location of bomb is highly essential in the field of defense
applications. Considering the value of human life the
robot is allowed in the field to detect the bomb.
RASPBERRY Pi
S.No
CODE
PROJECT TITLE
1
ET13R
P1
Proposal of Sensor Data Gathering with Single Board
Computer
We propose a sensor data gathering system using a single
board computer for home energy management systems.
This sensor system should be capable of handling 100
sensor data per second. Since a single board computer has
low power consumption and low performance, it is used as
the sensor data gathering server.
Building network appliances with NanoBSD operating
system on Single Board Computers
There is presented an overview what NanoBSD operating
system is and how to use it in building powerful network
appliances on Single Board Computers (SBC). The
supposed audience of this paper is IT/network engineers,
researchers, students, Unix/Linux or BSD fans with
interest focused on building their own network appliances
based on embedded computers
Evaluation of clock synchronization methods for
measurement and control using embedded Linux SBCs
This paper reports a study and practical evaluation of two
different clock synchronization methods for distributed
measurement and control nodes based on Linux Single
Board Computers (SBCs) with ARM processors and
communicating through a TCP/IP wide area network.
DESCRIPTION
2
ET13R
P2
DESCRIPTION
3
ET13R
P3
DESCRIPTION

17. 4
ET13R
P4
DESCRIPTION
An improved real-time surveillance system for home
security system using BeagleBoard SBC, Zigbee and FTP
webserver
A number of surveillance devices in a Zigbee protocol
(IEEE 802.15.4) based wireless network are connected to a
Beagle-Board Single Board Computer (SBC) based
surveillance management system. Remote alerting on fire
and intruder detection are the key features of the system.
When smoke or intruder movement is detected, the
system sends warning messages through Short Message
Service (SMS) to cell phones, starts capturing real-time
video for fixed duration and makes the alarm on.
INDUSTRIAL AUTOMATION & PLC
S.No
CODE
PROJECT TITLE
1
ET13
iP1
Utilization of the PLC as a web server for remote
monitoring the technological process
This paper presents a new methodology to develop remote
laboratories for systems engineering and automation
control courses, based on the combined use of TwinCAT,
a laboratory Java server application, and Easy Java
Simulations (EJS). The TwinCAT system is used to close
the control loop for the selected plants by means of
programmable logic controllers (PLCs) deployed in PCs
with the a run-time tool.
Remote Control Laboratory Using EJS Applets and
TwinCAT Programmable Logic Controllers
DESCRIPTION
2
ET13
iP2

18. DESCRIPTION
3
ET13
iP3
DESCRIPTION
4
ET13
iP4
DESCRIPTION
5
ET13
iP5
DESCRIPTION
6
ET13
iP6
This paper presents how it is possible to utilize PLC in the
task of the Web server. Described is configuration of the
PLC and its connection to the computer network. Next is
described principle of creation dynamic web page and
described are function for process variable data read and
write.
Development of a Low Cost Programmable Logic
Controller
The aim of this study is to develop a low cost small
module (hardware card), for use in the automation of
simple machines and equipments. programmable logic
controller (PLC) will be part of an open platform that also
contains a free software tool for programming PLC in C
language & online tutorial with detailed instructions about
building & programming the system.
Optimization through artificial neural network on a
Programmable Logic Controller for a Sludge Drying
Plant
The Sludge Drying Plant (SDP) is the final processing
facility of Effluent Treatment System (ETS) that produces
bio-sludge cake before it is sent out for final disposal. Due
to the process disturbances, mechanical and inconsistent
chemical reactions, the amount dry solid is reduced
tremendously.
Programmable Logic Controller (PLC) for polymer
mixing tank
The process requires manually mixing the cationic
polymer long chains with raw water to produce a product
that will be sent to the sludge tank process and filter press
process where the sludge will harden for disposal.
Design and fabrication of Programmable Logic
Controller Kit with multiple output module for teaching
and learning purposes

19. DESCRIPTION
The existing PLC trainer board comes with a casing where
students have the difficulty in observing and
understanding the connection between the input module,
PLC controller and output modules. The development of
PLC Kit has been designed and improved by increasing
the number of input and output components, cost
reduction and it is also user friendly.
DIGITAL IMAGE PROCESSING
S.No
CODE
PROJECT TITLE
1
ET13
iM1
Research on edge detection algorithm for plate image
DESCRIPTION
In view of the problems that traditional edge detection
algorithms are sensitive to noise and the environment of
plate scene is complex, plate image is smoothed with
Gaussian filter, and by comparison of edge images from
non-subsampled contour let edge detection algorithm and
multi-scale wavelet edge detection algorithm, a new
algorithm, pulse coupled neural network edge detection
algorithm based on multi-scale wavelet transform is
proposed.
ET13
iM2
A Flexible Method For Recognizing Four-Digit Numbers
On A License-Plate In A Video Scene
2
DESCRIPTION
3
ET13
iM3
In order to realize a simple system for monitoring car
movements, a flexible method was developed for
recognizing four-digit numbers on a license-plate in a
video scene. The method consisted of three parts; global
search for finding a license plate in a scene, corner
detection for removing shape deformation, and numeral
character recognition. The spatial features and the spectral
(color) ones were merged and processed at a time in the
global search.
An adaptive threshold edge detection method based on
the law of gravity

20. DESCRIPTION
4
ET13
iM4
DESCRIPTION
5
ET13
iM5
DESCRIPTION
6
ET13
iM6
DESCRIPTION
This algorithm make up for the traditional algorithm in
the whole image only used a single threshold. Through the
experimental comparison, this paper algorithm can create
dynamic adaptive threshold value. The algorithm has good
inhibition effect used in image with salt and pepper noise
and gaussian noise. it can extract image edge efficiently.
Facial Feature Extraction With A Depth Aam Algorithm
The main idea of our method is to use the face detection
algorithm with a Kinect camera to accurately locate
human head and estimate head pose. A depth AAM
algorithm is developed to locate the detailed facial features.
Experimental results show that our depth AAM algorithm
can effectively and accurately locale facial features from
video objects in conditions of complex backgrounds and
various poses.
An Informed Watermarking Scheme Using Hidden
Markov Model In The Wavelet Domain
This paper presents a new informed image watermarking
scheme with high robustness and simplified complexity.
Simulation results demonstrate that the proposed
informed watermarking algorithm has high robustness
against common attacks in signal processing and shows a
comparable performance to the state-of-the-art scheme
with a greatly reduced arithmetic complexity.
A Novel Data Embedding Method Using Adaptive Pixel
Pair Matching
This paper proposes a new data-hiding method based on
pixel pair matching (PPM). The basic idea of PPM is to
use the values of pixel pair as a reference coordinate, and
search a coordinate in the neighborhood set of this pixel
pair according to a given message digit. Experimental
results reveal that the proposed method not only provides
better performance than those of OPAP and DE, but also
is secure under the detection of some well-known
steganalysis techniques.

21. 7
ET13
iM7
DESCRIPTION
TRAFFIC CONGESTION IDENTIFICATION
BASED ON IMAGE PROCESSING
This study proposes a novel approach towards traffic
congestion identification based on vehicle trajectories in
intelligent vehicle infrastructure co-operation system
(IVICS). Considering spatial-temporal trajectories as
image, this study uses self-correlation to extract
propagation speed of congestion wave.
Android
S.No.
1
CODE
ET13A
N1
DESCRIPTION
2
ET13A
N2
DESCRIPTION
PROJECT TITLE
Energy management application for smart grids
aiming at mobile device
This paper presents methods for monitoring and
controlling the energy consumption, which
supported the development of an Android
application (for mobile devices) to interact with a
Smart Grid Network.Through this application the
costumer may visualize its energy consumption data
and use this information to support decisions
regarding the management, control or adequacy of
their consumption habits.
Portable wireless biomedical temperature
monitoring system: Architecture and
implementation
This paper demonstrates the design and
implementation of a portable embedded system
targeting continuous temperature monitoring with
wireless interface capability. Our main motive is to
provide a solution for monitoring babies', disable or
elderly population body temperature and initiate
immediate alarm in case of hazardous cases.

22. 3
ET13A
N3
DESCRIPTION
4
ET13A
N4
DESCRIPTION
5
ET13A
N5
DESCRIPTION
6
ET13A
N6
DESCRIPTION
Design and implementation of a wireless
tensiometer with smartphone interface
The prototype has been developed to allow the final
user to keep a register of its own blood pressure
measurement. The application also can generate a
report with the measurement data that can be sent
to a doctor or to an online database historical profile
keeping, which may be useful for remote diagnosis
procedures.
A Common Interface for Bluetooth-based Health
Monitoring Devices
In this project a patient temperature and heart rate
are monitored and displayed in an android device.
This data’s are sent and received by using a
Bluetooth module
Remote Monitoring System of ECG and Human
Body Temperature Signals
The paper presents a remote monitoring system for
electrocardiographic and temperature signals. The
system consists of a hardware module for
acquisition, a Bluetooth transmission module and
finally a displaying module (PC or mobile devices).
Information is sent via IP (GPRS or Wi-Fi) to a
database
A Bluetooth toy car control realization by android
equipment
A remote toy car controlled by an android mobile
platform with Bluetooth technology is presented in
this paper. The mobile platform requests to connect
with the small car then sends instructions to control
it by calling the android system Bluetooth API.

23. 7
ET13A
N7
DESCRIPTION
8
ET13A
N8
DESCRIPTION
Smart home system for Disabled People via
Wireless Bluetooth
in our project work, we attempt to design the smart
home system including the wireless controller via
Bluetooth technology. This software application
adapt in mobile phone, PDA, mobile computer
using android's operating system (OS). This
software application will control the electrical
appliances switches wirelessly (Bluetooth).
Bluetooth-Based Android Interactive Applications
for Smart Living
For smart living, interactive applications are
increasingly important especially on interaction of
people and the environment. In this work, a
Bluetooth-based
mobile
sensor
interactive
application in Android- designed & implemented.
ARDUINO
S.No.
1
CODE
ET13A
R1
DESCRIPTION
2
ET13A
R2
DESCRIPTION
PROJECT TITLE
Data acquisition and control using ArduinoAndroid platform: Smart plug
In this work, we propose to develop a smart plug, an
energy monitoring system that provides real time
update of the energy consumption at the device level.
The proposed device is using an arduino
microcontroller board, an ENC28J60 ethernet
module, and a current transformer sensor.
ZigBee wireless sensor network for radiation
monitoring at nuclear facilities
This paper describes the design of a WSN that allows
smart real time monitoring of radiation levels at
nuclear facilities. We develop a local low cost
prototype of wireless sensor node equipped with a
radiation sensor. The wireless node based on ZigBee
technology and Arduino platform.

24. 3
ET13A
R3
DESCRIPTION
4
ET13A
R4
DESCRIPTION
Development of an educational environment for
online control of a biped robot using MATLAB and
Arduino
This paper describes the development of innovative
low-cost educational platform to study and control a
biped robot in real-time using MATLAB and
Arduino board. MATLAB was used as a control and
visualization environment, while the Arduino board
was utilized as a final controller for the servo motors
as well as a Data Acquisition Card (DAC).
Automatic control for laboratory sterilization
process based on arduino hardware
This System is based on Arduino Board. Arduino is
an Open Hardware platform that allows a fast
prototype development, Arduino microcontroller is
programmed on C++. making development and tests
not a difficult part of overall work.