Corbetta Fia - Technical data sheet

Notes:
The technical data sheets can and should be enriched with new information, knowledge and learning;
is then open to the new, without a concluding part.
Copyright 2014 – CORBETTA|FIA srl – Carugo (CO). The information contained in this Company Technical Manual
are protected by copyright under the Berne Convention. Any reproduction, even in part, in any form or by any
copying system is prohibited unless written permission. Any violation will therefore be prosecuted according to law.

PRODUCTS CHART
1.1.1 Monostrato Product for “flat” panels edging
1.1 PAPER 1.1.2 Soft-forming EA Product for soft edgings
1.1.3 Battuta porte Product for door-beat coating
1.1.4 Bordo retro Product for edging of not-visible parts
1. EDGE-BANDINGS
1.2.1 Laminex Product for “flat” panels edging
1.2.2 Lamisoft Product for soft edgings
1.5 LAMINATE 1.2.3 Laminex LAC Not finihed product to be varnished
1.2.4 Cover LAC Not finished product to be varnished for soft
2. COATING 2.1. Flexan Finished product for profiles coating
PAPERS
3.1 Micro Top Flexible product for vertical surfaces coating
3. LAMINATES FOR 3.2 Thin Flex Extra-flexible product for vertical surfaces coating
SURFACES 3.3 Thin Top Product for horizontal surfaces coating

1.1 MONOSTRATO paper edge-banding
1.1.1 Monostrato
1.1.2 Soft-forming EA
1.1.3 Battuta porte
1.1.4 Bordo retro
1.- Product class
Single-layer edge-banding specific for the edging of melamine faced chipboards.
2.- Description
Monostrato is obtained impregnating a single layer of high gramage printed or plain colour paper; the paper is impregnated with
ureic-acrylic resins and then it is lacquered with finishing lacquers.
It is available in Standard version for “flat” panels edging, Bordo retro for edging of not-visible parts, Softforming EA for curved
surfaces edging and Battuta porte for the difficult door-beat coating.
3.- Advantages
 The cardboard offers a good covering against the panel irregularities,
 The flexible versions (Softforming EA and Battuta porte) allow to coat very sharp radius,
 Possibility of replicating decors and finishings of the melamine faced chipboard,
 Aesthetic look of real wood,
 Applicability with all different plant types which are used in the edging field (the customer is however
recommended to test in advance).
4.- Applications
Monostrato is particularly suitable for coating:
 Melamine faced chipboard edges,
 Profiles for the doors industry,
 Shaped borderings.
It can be applied on chipboards, MDF and plywoods using all the usual gluing processes.
The product is suitable for all standard uses in interior furnishings. The product is not waterproof.
Applications with glues
 For gluing with hot mel polyolefinic and polyurethane-based adhesives, the edge must be sanded just on the backside,
IT IS ABSOLUTELY AVOID the use of primer;
 In case of EVA-based hot melt adhesives, there is the possibility of applying a primer on the backside, to facilitate the
sticking of the edge-banding to the panel, UPON testing for checking the primer compatibility with the glue which is
used on the plant.
5.- Sizes
 Edge-banding thickness: 0,28 +/- 0,02 mm
 Supplied in rolls, cut to a wide range of widths,
 Rolls length: 400 – 800 linear meters
 Light resistance (blue wool scale) ≥ 6
6.- Packaging and storage
Monostrato is supplied in rolls, which are wrapped on cardboard cores with an inner diameter of 152 mm. and protected by shock-
proof packagings. Monostrato can be supplied cut-to-rolls and packed in cardboard boxes. The stability of Monostrato is assured
for twelve months, if kept in its original packaging and in proper environmental conditions (temperature 10 – 25°C and relative
humidity 50 – 60 %).
7.- Notes
The information contained in this document are based on our current knowledge and experiences. However, they cannot be
considered as exhaustive, but purely indicative.
We suggest to test the product in advance on your own plant and to report eventual unqualified material before proceeding with
further productions.
CORBETTA|FIA srl cannot be considered as responsible for any eventual damage deriving from the use of the above mentioned
product.
Technical data sheet

1.2.1 LAMINEX laminate for edge-banding
1.- Product class
Plastic CPL specific for edging the melamine-laminated panels.
2.- Description
Laminex is obtained laminating decorative papers that have various layers applying in between some vegetable parchments.
Both the décor and the base papers are impregnated with melamine resins.
3.- Advantages
 Melamine impregnation with high chemical and mechanical resistance,
 Possibility to edge all the range of thickness between 0,4 and 1,0 mm,
 Possibility to perform all the decors and the finishing of the melamine-laminated panel,
 High resistance to the superficial wear and tear,
 Suitable to edge flat chipboards and chipboards with wide curve radius, for lower radius specific products
available in a wide range are available and can be required,
 Applicability with all kinds of plant which are used in the edging field (however the customer is recommended
to test in advance).
4.- Applications
Laminex is a product particularly suitable for the covering of edges of the melamine laminated panel. It can be applied on
chipboards, MDF and plywoods using all the usual gluing processes,
The product is suitable for all standard uses in interior furnishings. The product is not waterproof
 To glue with polyolefin hot melt and polyurethanic-based adhesives, the edge must be sanded just on the backside,
ABSOLUTELY AVOIDING the use of primer;
 In case of EVA-based hot melt adhesives, there is the possibility to apply a primer on the backside, to help the sticking
of the edge-banding on the panel, BEFORE checking the primer compatibility with the glue which is used on the plant.
5.- Sizes
 Raw printed paper initial gramage 60 – 120 gr/sqm
 Available on roll in width: 65 and 130 cm
 Supplied in rolls, cut to a wide range of widths,
 Roll length: 300 – 500 linear meters
6.- Technical characteristics
The technical characteristics are summed up in the table n° 1.
Laminex is supplied in rolls, which are wrapped on cardboard cores with an inner diameter of 152 mm. and protected by shock-
proof packagings. Laminex can be supplied cut-to-rolls and packed in cardboard boxes. The stability of Laminex is assured for
twelve months, if kept in its original packaging and in proper environmental conditions (temperature 10 – 25°C and relative
8.- Notes
product.

Table n° 1 – Technical data of laminate for edge-banding LAMINEX
Properties Reference norm Measure Value
Light resistance
Stains resistance
Wet heat resistance
Dry heat resistance
Scratch resistance
Abrasion resistance
Formaldehyde emission
Edging resistance to heat 1
EN 438-2/05 §
27
EN 438-2/05 §
26
EN 12721/09
EN 12722/09
UNI EN 9428
UNI EN 9115
EN 717-2:1996
UNI 9242:1987
blue wool
scale
class
degree
degree
level
WR cycles
mgHCHO/m2h
degree
> 6
3 - 5
5
5
5
85
0,4
5
1 The test has been made on stacked edge-bandings with polyurethanic glue on chipboards.
Laminex can be produced with melamine overlay on the décor that permits to do a mechanical scratching before lacquering without
damaging the décor;
Laminex can be produced with a protective film.

Technical Data Sheet
1.2.2 LAMISOFT laminate edge-banding for soft-forming
1.- Product Class
CPL plastic laminate specific for the soft-forming edging of melamine chipboard.
2.- Description
Lamisoft is obtained laminating a decorative paper with a base paper gramage of 155 gsm; both decorative paper and base
paper are impregnated with particular resins that give the product an excellent flexibility.
3.- Advantages
 Impregnation with resins that guarantee a good mechanical resistance combined with an excellent flexibility.
 Feasible thickness: basing on the decorative paper gramage, it can be obtained a thickness between 0,25
and 0,27 mm.
 Possibility to repeat all the designs and all the finishes of the melamine chipboard.
 Applicability with the plants used in the covering sector (anyhow we always recommend to the customer to
proceed with a preventive test).
4.- Applications
Lamisoft is a product particularly suitable for the profiles covering, it can be applied on chipboards, MDF and plywood using all
the usual sticking processes; it can be used for covering frames, skirtings, arriving till the doors profiles.
Application with glues
 For the sticking on the different types of profiles, it is necessary that the glue is spread over the edge-banding and
NOT over the board; it is suggested the use with edging/covering plants provided with contrast pressure roller, in any
case it is warmly recommended the realization of preventive tests in compliance with the proper plant conditions (type
and temperature of the glue, covering speed, environmental conditions … etc.)
 In case of EVA based hot melt adhesives, there is the possibility to apply a primer on the back for facilitating the sticking
of the edge-banding to the board, by PREVIOUS test for verifying the primer compatibility with the glue used on the
plant.
5.- Sizes
 Initial raw decorative paper gramages: 60 – 80 gsm
 Delivered in rolls with widths: 65 and 130 cm
 Delivered in rolls cut in a wide range of widths
Lamisoft is supplied in rolls, which are wrapped on cardboard cores with an inner diameter of 152 mm. and protected by shock-
proof packagings. Lamisoft can be supplied cut-to-rolls and packed in cardboard boxes. The stability of Lamisoft is assured for
8.- Notes
product.

Table n° 1 – Technical data of laminate edge banding sheet LAMISOFT
Light resistance
Stains resistance
Wet heat resistance
Dry heat resistance
Scratch resistance
Abrasion resistance
EN 438-2/05 §
27
EN 438-2/05 §
26
EN 12721/09
EN 12722/09
UNI EN 9428
UNI EN 9115
EN 717-2/96
Blue wool scale
class
degree
degree
class
WR cycles
mgHCHO/m2h
> 6
3 - 5
5
5
4
50
≤ 1,2

1.2.3 LAMINEX LAC laminate to be lacquered
1.- Product class
CPL plastic laminate specific for the edging of melamine faced chipboards and for the lacquering.
2.- Description
Laminex LAC is made laminating decorative papers with various base paper layers. Both decorative paper and base paper are
impregnated with particular thermoplastic resins.
3.- Advantages
 Impregnation with thermoplastic resins that guarantee a good mechanical and chemical resistance,
 Possibility to realize it in thickness 0,4; 0,6; 0,8 and 1,0 mm,
 High abrasion resistance that allows the surface sanding down in order to facilitate the following varnishing operations.
 Applicability with different edging plants (anyhow, we always recommend to the customer to proceed with a preventive
test).
4.- Applications
Laminex LAC is a product particularly suitable for the edging of the melamine faced board, it can be applied on chipboards, MDF
and plywood; after its application you can proceed to the lacquering operation avoiding the annoying problem of “blow” that
sometimes occurs when you use other types of edge-bandings.
The extreme closeness permits, for thickness starting from 0,8 mm and more, to get a pleasant rounded off effect.
The product is suitable for all standard uses in interior furnishings. The product is not waterproof
 For sticking with polyolefin hot melt glues and Polyurethane based, the edge-banding has to be only polished on the
back ABSOLUTELY AVOIDING the use of the primer;
 For sticking with EVA based hot melt glues it is necessary that the edge-banding is polished and with primer on the
back (anyhow, we always recommend to the customer to proceed with a preventive test).
5. -Sizes
 Rolls length: 150 – 400 linear meters, depending on the thickness.
Technical characteristics are summarized on Table 1.
Laminex LAC is supplied in rolls, which are wrapped on cardboard cores with an inner diameter of 152 mm. and protected by
shock-proof packagings. Laminex LAC can be supplied cut-to-rolls and packed in cardboard boxes. The stability of Laminex LAC
is assured for twelve months, if kept in its original packaging and in proper environmental conditions (temperature 10 – 25°C and
relative humidity 50 – 60 %).
8.- Notes
product.

Wet heat resistance
Dry heat resistance
EN 12721/09
EN 12722/09
EN 717
Class
Level
mgHCHO/m2h
5
5
1,3
Table n° 1 – Technical data of laminate to be lacquered sheet LAMINEX LAC

1.2.4 Cover LAC laminated edge-banding to be varnished for soft edging
1.- Product class
CPL plastic laminate specific for the soft-forming edging and the following lacquering of melamine faced chipboards.
2.- Description
Cover LAC is obtained laminating a decorative paper with a 155 gsm base paper; both decorative paper and base paper are
impregnated with particular thermoplastic resins which give to the product an excellent flexibility.
3.- Advantages
 Impregnation with resins that guarantee a good mechanical resistance combined with an excellent flexibility,
 Lacquering easiness
 High covering of the defectiveness of the element to be covered
 Applicability with all the various types of plants used in the edging sector (anyhow we always recommend to
the customer to proceed with a preventive test).
4.- Applications
Cover LAC is a product particularly suitable for the profiles covering, it can be applied on chipboards, MDF and plywood using all
the usual sticking processes; it can be used for covering frames, skirtings and doors profiles.
 For the sticking on the different types of profiles, it is necessary that the glue is spread on the edge-banding and
NOT on the board; it is suggested the use with edging-covering plants provided with contrast pressure rollers in any
case it is warmly recommended the realization of preventive tests in compliance with the proper plant conditions (type
and temperature of the glue, covering speed, environmental conditions … etc.)
 In case of EVA based hot melt adhesives, there is the possibility to apply a primer on the back for facilitating the sticking
of the edge-banding to the board, PREVIOUS test for verifying the primer compatibility with the glue used on the plant.
5. - Sizes
 Initial raw decorative paper gramages: 60 – 80 gsm
Cover LAC is supplied in rolls, which are wrapped on cardboard cores with an inner diameter of 152 mm. and protected by shock-
proof packagings. Cover LAC can be supplied cut-to-rolls and packed in cardboard boxes. The stability of Cover LAC is assured
for twelve months, if kept in its original packaging and in proper environmental conditions (temperature 10 – 25°C and relative
7.- Notes
product.

2.1 FLEXAN finish foil for coating
1.- Product class
Post-impregnated Finish Foil
2.- Description
Flexan is obtained using printed and/or plain colour decorative papers, impregnated with modified specific ureic-acrylic resins
and spread with finishing lacquers.
By the coating, basically two superficial coatings, that differ one from the other in the brightness degree, can be done: matt (4-8
gloss) and semi-matt (15-20 gloss) finishing.
3.- Advantages
 High flexibility,
 Possibility to coat profiles with curving radius ≥ 1 mm
 High quality finishing lacquers,
 Wide range of decors,
 Applicable by different plants and glues used in the coating field (we always recommend to the customer to
test first).
4.- Applications
Flexan is an extremely flexible product suitable to coat several kinds of profiles (frame, skirtings, door-jambs, casing, shelves,
etc...)
It can be applied on chipboards, plastic and metallic profiles, MDF and plywood by standard gluing processes.
5. - Sizes
 Raw printed paper initial grammage 60 – 100 g/sqm
 Available on roll in width: 60 - 80 cm
Flexan is supplied in rolls, which are wrapped on cardboard cores with an inner diameter of 152 mm. and protected by shock-
proof packagings. Lamisoft can be supplied cut-to-rolls and packed in cardboard boxes. The stability of Flexan is assured for
8.- Notes
product.

Dirt resistance
Light resistance
Stains resistance
UNI 9300:1988
EN 438-2/05 § 27
EN 438-2/05 § 26
level
blue wool scale
class
4
> 6
3 - 5
Table n° 1 – Technical data of finish Foil for coating sheet FLEXAN

3.1 Micro Top XS - Micro Top XS morbido - Micro Top XS DU - Micro Top XST
1.- Product Class
Laminates of Micro Top group can be used for coating a lot of profiles.
2.- Description
Micro Top products are obtained laminating a layer of decorative paper which is impregnated with particular thermo-plastic resins
combined with a support layer. In case that support layer is of vegetable parchment we obtain Micro Top XS: this a laminate with
very good properties of form both by hot and cold process. For coating lower radius of curvature than radius made with XS, you
can use Micro Top XS morbido which is made using vegetable parchment but it is realized using more flexible resins. The product
suitable for coating even lower radius is Micro Top XST, which is obtained replacing vegetable parchment with a non-woven fabric
layer (tnt).
3.- Characteristics:
 Superficial melamine coating with high physical and chemical resistance,
 Possibility to reproduce all the decors and a lot of finishings of melamine-laminated panels,
 Applicable by different plants used in the coating field (we always recommend to test in advance)
 Radius of curvature that can be obtained:
radius 90°C radius 180 °C
Product Radius (mm)
90° 180°
Micro Top XS ≥ 3 ≥ 3,5
Micro Top XS morbido ≥ 2 ≥ 2,5
Micro Top XS DU ≥ 1 ≥ 1,5
Micro Top XST ≥ 1 ≥ 1
Values of radius of curvature indicated in the here above table are valid when covering at speed of ≤ 20 lm/min and using glue
temperature: T ≥ 150 °C for polyurethanic glues and T ≥ 180 °C for polyolephinic glues. Before using, all laminates of Micro Top
group have to be stocked at temperature and humidity as indicated at point nr. 7 – packaging and storage.
4.- Applications
Laminates of Micro Top group are thin products which are suitable for coating different kinds of profiles (frames, skirtings, door-
jambs, etc...). and on vertical surfaces (shutters, lateral parts of furniture, etc ...).
They can be applied on chipboards, MDF and plywoods using all usual processes of gluing.
These products are suitable for all standard uses in interior furnishings. The products aren’t waterproof.
Applicazioni con collant
 For gluing on different kinds of profiles, it is necessary that the glue is spread on the laminate and not on the
chipboard. We advise the use with edging/coating plants equipped with contrast pressers. In any case we recommend
to test in advance, in order to check that the use is appropriate with the plant conditions (type and temperature of the
glue, coating speed, environmental conditions and so on).
5. - Sizes
 Initial grammage of raw printed paper 60 – 80 g/sqm
 Thickness: 0,14 ± 0,02 mm
 Available in rolls, width: 65 e 130 cm
 Length of rolls: 400 – 800 linear meters
Technical characteristics of Micro Top are summarized in the table nr. 1.

Laminates of Micro Top group are supplied in rolls, which are wrapped on cardboard cores with an inner diameter of 152 mm and
are protected by a shock-proof packaging. They can be supplied cut-to-rolls and packed in cardboard boxes. The stability of
laminate is assured for twelve months, if kept in its original packaging and in proper environmental conditions (temperature 10 –
25° C and relative humidity 50 – 60 %).
8.- Notes
product.
Table n° 1 - Technical data of laminate for coating MICRO TOP XS – XS morbido - DU - XST
Abrasion resistance
Scratch resistance
Dirt resistance
Light resistance
Wet heat resistance
Dry heat resistance
Stains resistance
UNI EN 9115
EN 438-2/05
EN 438-2/05
UNI EN 9428
UNI 9300:1988
EN 438-2/05 § 27
EN 12721/09
EN 12722/09
EN 438-2/05 § 26
EN 717-2:1996
WR cycles
IP cycles
IP cycles
class
level
blue wool scale
degree
degree
class
mgHCHO/m2h
85
Overlay AC3: 2.000
Overlay AC5: 6.000
XS: 5
XS morbido:4
XS DU: 4
XST: 4
5
≥ 6
5
5
3 - 5
XS - XS morbido – XS DU: 0,6
XST: 1,7

3.2 THIN FLEX ultra-thin laminate for coating
1.- Product Class
Laminate for coating characterized by high flexibility.
2.- Description
Thin Flex is obtained laminating a layer of decorative paper which is previously impregnated with particular thermo-plastic resins
and then the surface is spreaded with melamine resin. The particular characteristics of the resin used for the impregnation give
the product a unique flexibility in its field and the melamine surface assures a good resistance against the superficial wear and
tear
To increase the thickness of the product without touching the characteristics of flexibility, you can laminate doubling with a layer
of non-woven fabric (tnt).
3.- Advantages
 Superficial melamine coating that has a high chemical resistance,
 Possibility to repeat all the decors of the melamine-laminated panels
 Applicability by different plants (we always recommend to the customer to test first)
4.- Applications
Thin Flex is an extremely flexible product suitable to coat all kinds of profiles (frame, skirting, door-jamb, staff-bead and so on)
and vertical surfaces (doors and so on).
It can be applied on chipboards, MDF and plywoods using all the usual gluing processes
To avoid any delamination problem, we advise that the initial gramage of the decorative paper is lower than 80gr/mm
 Applicability with all kinds of glue used in the coating field; we recommend to test first, to check the plant
conditions according to the quality of the gluing.
5.- Sizes
 Raw paper initial grammage: 60 – 80 gr/sqm
 Supplied in rolls with standard width: 65 and 130 cm
Thin Flex is supplied in rolls, which are wrapped on cardboard cores with an inner diameter of 152 mm. and protected by shock-
proof packagings. Thin Flex can be supplied cut-to-rolls and packed in cardboard boxes. The stability of Thin Flex is assured for
8.- Notes
product.

Table n° 1 - Technical data of laminate for coating Thin Flex
Abrasion resistance
Scratch resistance
Dirt resistance
Light resistance
Wet heat resistance
Dry heat resistance
UNI EN 9115
UNI EN 9428
UNI 9300:1988
EN 438-2/05 § 27
EN 12721/09
EN 12722/09
EN 717–2:1996
cycles
class
level
blue wool scale
degree
degree
mgHCHO/m2h
50
3
5
≥ 6
5
5
0,2

1.- Product class
Post-formable plastic laminate CPL.
2.- Description
The Thin Top is obtained by laminating a decorative paper with several layers of phenolic support depending on the required
thickness; the decorative paper is impregnated with melamine resins.
Thin Top antistatic is characterized by the high laminate capacity to eliminate electrostatic charges, this is obtained activating the
melamine resin with specific substances.
For obtaining Thin Top antibacterial we use specific substances which have an authentic antibacterial action.
Thin Top anti-imprint is obtained by laminating a specific decorative paper with several layers of
phenolic supports depending on the required thickness. The decorative paper is subjected to specific surface treatments that
give it lipofobe characteristics, for example fingermark doesn’t appear on the surface. Any possible little marks can be easily cleaned.
3.- Advantages
 Melamine impregnation with high chemical and mechanical resistance,
 Possibility to produce all the range of thicknesses from 0,4 to 1,8 mm,
 Possibility to reproduce all the decors with all the finishings of the melamine-laminated chipboard:
 Possibility to post-form
 Applicability with all kind of plants used in the filed of plating (we always recommend to the customer
to test first).
4.- Applications
Thin Top is a product particularly suitable for the coating of plain, vertical and horizontal surfaces, thanks to its post-forming
property, it can be used to coat kitchen tops; it can be applied on chipboard, MDF and plywood using all standard gluing
processes.
The Thin Top can be used using as decorative a thin layer of real aluminum available in several finishings or a décor printing with
a digital technology.
Thin Top antistatic is used in all rooms in which electrostatic charges must be avoided.
Thin Top antibacterial is perfect for furnishing public places like hospitals, laboratories, public toilets, etc ...
Thin Top anti-imprint can be used for coating piece of furniture frequently used which are in contact with fingers or with oily
and greasy products, like table for kitchen, desk, shutter, front dresser, etc.…
The Thin Top is suitable for the use in the naval field certified by LAPI S.p.A.; certificates 0987/MED-B/236 (form B) and
0987/MED-D/466 (form D).
 The Thin Top can be applied with standard glue processes used in the plating field.
the customer is however recommended to test in advance).
5.- Sizes
 Raw paper initial gramages 60 – 120 g/sqm
 Supplied in sheets of size: length 1.300 mm and width from 2.000 to 4.200 mm
The technical characteristics of Thin Top, Thin Top antistatic and Thin Top antibacterial are summarized in the table n.1.
The technical characteristics of Thin Top anti-imprint are summarized in the table n.2.
The laminate Thin Top is supplied in sheets on pallets, which are wrapped with polyethylene and a shock-proof packaging. The
stability of laminate is guaranteed for twelve months, if kept in its original packaging and in proper environmental conditions
(temperature 10 – 25°C and relative humidity 50 – 60 %,).
product.
3.3 THIN TOP post-formable laminate
THIN TOP post-formable laminate and antistatic
THIN TOP post-formable laminate and antibacterical
THIN TOP post-formable laminate and anti-imprint

8.- Notes
product.
Table n° 1 - Technical data of laminate Thin Top, Thin Top antistatic and Thin Top antibacterial
Properties Reference norm 1 Measure Value
Antibaterical activity2
Volumetric resistance 3
ISO 22196:2007
IEC 61340-4-1
%
Ohms
99,9 %
108 - 1011
Light resistance
Stains resistance
Scratch resistance 4
Abrasion resistance 5
Dry heat resistance
Wet heat resistance
EN 438-2/05 § 27
EN 438-2/05 § 26
EN 438-2/05 §25
EN 438-2/05 §10
EN 717-2:1996
UNI EN 12722
UNI EN 12721
blue wool scale
class
class
WR cycles
mgHCHO/m2h
degree
degree
> 6
4 - 5
4
Plain colours: 250
Printed colours: 75
With overlay: 450
0,1
5
5
1.- The checked data applying the methods established by the regulation UNI EN 438-2 can be different from the minimum requisites set by UNI en
438-3 for HPL laminates;
2.- The value is valid only for Thin Top antibacterial;
3.-The value is valid only for Thin Top antistatic;
4.- The scratch resistance is strongly influenced by the shade and by the surface finishing;
5.- The resistance to surface wear and tear can be better adding an OVERLAY.
SPECIFIC USES
A THIN TOP in the version MED is suitable to the use in the naval field certified by LAPI SpA with reference to the certificates n°
0987/MED-B/236 (form B) and n° 0987/MED-D/466 according to the following criteria:
Average laminate density Thickness range Test method
(gr/sqm) (mm)
From 769 to 2.031 0,6 - 1,5 FTP Code Annex 1 Part 2 (1996)
+ MSC Circ. 916 (1999)

Table n° 2 - Technical data of laminate THIN TOP anti-imprint
Light resistance
Stains resistance
Scratch resistance
Abrasion resistance
Vapour resistance
Dry heat resistance
EN 438-2/05 § 27
EN 438-2/05 § 26
EN 438-2/1991
EN 438-2/05 §10
EN 438-2 § 14
UNI EN 12722
Blue wool scale
class
class
WR cycles
class
degree
> 6
3 - 5
Level2, ≥ 3 N
190
5
5
SPECIFIC USES
THIN TOP in the version MED is suitable to the use in the naval field certified by LAPI SpA with reference to the
certificates n° 0987/MED-B/546 (form B) and n° 0987/MED-D/466 according to the following criteria
Average laminate density Thickness range Test method
(gr/sqm) (mm)
From 769 to 2.031 0,6 - 1,5 FTP Code Annex 1 Part 2 1996)
+ MSC Circ. 916 (1999)

Corbetta Fia - Technical data sheet

Recommended

Recommended

More Related Content

Viewers also liked

Viewers also liked (18)

Similar to Corbetta Fia - Technical data sheet

Similar to Corbetta Fia - Technical data sheet (20)

Recently uploaded

Recently uploaded (20)

Corbetta Fia - Technical data sheet