2. Shutdown SIS
Previous Screen
Product: EJECTOR TRUCK
Model: 730C EJECTOR TRUCK LFH
Configuration: 730C Ejector Articulated Truck LFH00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
730C and 730C EJECTOR Articulated Trucks
Engine Supplement
Media Number -UENR2344-00 Publication Date -01/10/2014 Date Updated -01/10/2014
i05859364
Engine - Remove and Install
SMCS - 1000-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 386-6032 Lever Puller Hoist Gp 1
B
5P-7306 Shaft Housing 1
5P - 7305 Engine Turning Tool 1
Start By:
a. Remove the air cleaner.
b. Remove the starter.
Personal injury can result from contact with refrigerant.
Contact with refrigerant can cause frost bite. Keep face and hands away
to help prevent injury.
Protective goggles must always be worn when refrigerant lines are
opened, even if the gauges indicate the system is empty of refrigerant.
1/11
730C Ejector Articulated Truck LFH00001-UP (MACHINE) POWERED BY C13 En...
2019/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Always use precaution when a fitting is removed. Slowly loosen the
fitting. If the system is still under pressure, release it slowly in a well
ventilated area.
Personal injury or death can result from inhaling refrigerant through a
lit cigarette.
Inhaling air conditioner refrigerant gas through a lit cigarette or other
smoking method or inhaling fumes released from a flame contacting air
conditioner refrigerant gas, can cause bodily harm or death.
Do not smoke when servicing air conditioners or wherever refrigerant
gas may be present.
Use a certified recovery and recycling cart to properly remove the
refrigerant from the air conditioning system.
Personal injury or death may result from failure to adhere to the
following procedures.
Fuel leaked or spilled onto hot surfaces or electrical components can
cause a fire.
Clean up all leaked or spilled fuel. Do not smoke while working on the
fuel system.
Turn the disconnect switch OFF or disconnect the battery when
changing fuel filters.
Personal injury can result from hot coolant, steam and alkali.
At operating temperature, engine coolant is hot and under pressure. The
radiator and all lines to heaters or the engine contain hot coolant or
steam. Any contact can cause severe burns.
Remove cooling system pressure cap slowly to relieve pressure only
when engine is stopped and cooling system pressure cap is cool enough
to touch with your bare hand.
Do not attempt to tighten hose connections when the coolant is hot, the
hose can come off causing burns.
2/11
730C Ejector Articulated Truck LFH00001-UP (MACHINE) POWERED BY C13 En...
2019/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Cooling System Coolant Additive contains alkali. Avoid contact with
skin and eyes.
1. Drain the coolant. Refer to Operation and Maintenance Manual, "Cooling System Coolant
(ELC) - Change" for the correct draining and filling procedures.
2. Recover the air conditioner refrigerant. Refer to Service Manual, SENR5664, "All Products
Air Conditioning and Heating Systems with R134a for All Caterpillar Machines". Refer to
Special Publication, NENG2500, "Air Conditioning Tools" for the correct tools.
3. Tilt the cab. Refer to Operations and Maintenance Manual, "Cab - Tilt" for the correct
procedure.
Illustration 1 g03699572
4. Remove tube assemblies (1).
Illustration 2 g03689077
5. Remove clips (4) and (5). Disconnect hose assembly (3) and remove the seal. Disconnect
hose assemblies (2), (6) and (7).
3/11
730C Ejector Articulated Truck LFH00001-UP (MACHINE) POWERED BY C13 En...
2019/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 18 g03689797
Typical Example
20. Attach a suitable lifting device to engine (37). The weight of engine (37) is approximately
1270 kg (2800 lb).
Illustration 19 g03689826
21. Install Tooling (B).
Illustration 20 g03689830
9/11
730C Ejector Articulated Truck LFH00001-UP (MACHINE) POWERED BY C13 En...
2019/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 21 g03689844
22. Remove plug (38).
23. Use Tooling (B) to rotate the engine and remove 12 bolts (39).
Illustration 22 g03689851
Illustration 23 g03698080
24. Remove bolts (41) and (40). Remove bolts (42).
10/11
730C Ejector Articulated Truck LFH00001-UP (MACHINE) POWERED BY C13 ...
2019/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 24 g03689857
Typical Example
25. Remove engine (37).
Installation Procedure
1. Install engine (37) in the reverse order of removal.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Dec 23 21:34:09 UTC+0800 2019
11/11
730C Ejector Articulated Truck LFH00001-UP (MACHINE) POWERED BY C13 ...
2019/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: EJECTOR TRUCK
Model: 730C EJECTOR TRUCK LFH
Configuration: 730C Ejector Articulated Truck LFH00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
730C and 730C EJECTOR Articulated Trucks Power Train
Media Number -UENR2348-00 Publication Date -01/10/2014 Date Updated -01/10/2014
i05938147
System Pressure - Release
SMCS - 3000-553-PX; 5050-553-PX
Pressure Release Procedure
At operating temperature, the hydraulic tank is hot and under pressure.
Hot oil and components can cause personal injury. Do not allow hot oil
or components to contact skin.
Remove the filler cap only when the engine is stopped, and the filler cap
is cool enough to touch with your bare hand. Remove the filler cap
slowly in order to relieve pressure.
1. If equipped with an ejector. Start the engine and fully retract the ejector blade. Move the
ejector control to the HOLD position.
2. If equipped with a truck body. Start the engine and lower the truck body or the water tank to
the frame. Move the hoist control to the FLOAT position.
3. Shut off the engine and then turn the engine start switch to the ON position.
4. Engage the service brakes several times until all pressure is relieved from the oil in the
service brake system.
5. Move the parking brake control between the ENGAGED position and the DISENGAGED
position. Repeat this procedure several times until all pressure is relieved from the oil in the
parking brake system.
6. Turn the engine start switch to the OFF position.
1/2
730C Ejector Articulated Truck LFH00001-UP (MACHINE) POWERED BY C13 En...
2019/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. 7. Rotate the steering wheel clockwise. Rotate the steering wheel counterclockwise.
8. Carefully remove the filler cap from the hydraulic tank for the Hoist/Ejector, Braking,
Steering and Fan Drive Systems.
9. Carefully remove the filler cap from the tank for the Output Transfer Gear System.
10. Carefully remove the filler cap from the Fuel tank.
11. Install the filler caps.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Dec 23 21:35:32 UTC+0800 2019
2/2
730C Ejector Articulated Truck LFH00001-UP (MACHINE) POWERED BY C13 En...
2019/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: EJECTOR TRUCK
Model: 730C EJECTOR TRUCK LFH
Configuration: 730C Ejector Articulated Truck LFH00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
730C and 730C EJECTOR Articulated Trucks Power Train
Media Number -UENR2348-00 Publication Date -01/10/2014 Date Updated -01/10/2014
i04937134
Torque Converter - Disassemble
SMCS - 3101-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 395-1099 Link Bracket 3
B 1P-0520 Driver Gp 1
C 154-6181 Forcing Screw 2
Start By:
a. Remove the torque converter.
Illustration 1 g03114321
1/8
730C Ejector Articulated Truck LFH00001-UP (MACHINE) POWERED BY C13 En...
2019/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. 1. Attach Tooling (A) and a suitable lifting device to housing assembly (2). The weight of
housing assembly (2) is approximately 30kg (70 lb). Remove bolts (1) and housing
assembly (2).
Illustration 2 g03114919
2. Use Tooling (B) in order to remove bearing (3). Remove ring (4).
Illustration 3 g03114926
3. Remove ring (5) from piston (6). Remove piston (6). Remove O-ring seal (7).
Illustration 4 g03115060
2/8
730C Ejector Articulated Truck LFH00001-UP (MACHINE) POWERED BY C13 En...
2019/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. 4. Remove bolts (8) and coupling assembly (9). Remove race (11). Remove retainer (10) and
the O-ring seal.
Illustration 5 g03115081
5. Remove plates and discs (12). Remove bearing (13).
Note: Mark the sequence of plates and discs (12) for installation purposes.
Illustration 6 g03115096
6. Use Tooling (C) in order to remove plate (14) and the O-ring seal.
3/8
730C Ejector Articulated Truck LFH00001-UP (MACHINE) POWERED BY C13 En...
2019/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 7 g03704564
7. Remove O-ring seal (15). Remove race (16). Use Tooling (C) in order to remove plate (17).
Illustration 8 g03115136
8. Remove dowels (18) and O-ring seal (19). Remove turbine (20).
Illustration 9 g03115161
9. Remove hub (21).
Illustration 10 g03116011
4/8
730C Ejector Articulated Truck LFH00001-UP (MACHINE) POWERED BY C13 En...
2019/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. 10. Remove race (22).
Illustration 11 g03116021
11. Remove bearing (23).
Illustration 12 g03116049
12. Use two people to reposition impeller (24). The weight of impeller (24) is approximately
31 kg (70 lb). Remove retaining ring (25). Remove impeller (24) from carrier (26).
Note: Make sure that carrier (26) is supported before removing retaining ring (25).
5/8
730C Ejector Articulated Truck LFH00001-UP (MACHINE) POWERED BY C13 En...
2019/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
21. Illustration 13 g03116054
13. Remove race (27), bolts (28), and impeller (24) from adapter (29). Remove hub (30).
Illustration 14 g03116118
14. Remove O-ring seal (31) from adapter (29).
Illustration 15 g03116228
15. Remove bearing (32). Remove carrier (26) from stator (33).
Illustration 16 g03116306
6/8
730C Ejector Articulated Truck LFH00001-UP (MACHINE) POWERED BY C13 En...
2019/12/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...