This document provides instructions for removing and installing various diesel exhaust fluid (DEF) system components on a Caterpillar 730C Ejector Articulated Truck. It includes procedures for the DEF tank, pump, injector, electronic control module, heater coolant solenoid valve, and fuel solenoid valve. The document contains illustrations and torque specifications for each component. Safety and installation notes are also provided.
Caterpillar cat 730 c ejector articulated truck (prefix tfh) service repair m...fjsekkdkmem
The document provides instructions for removing and installing various components of a 730C Ejector Articulated Truck, including the diesel exhaust fluid tank, pump, injector, electronic control unit, and solenoid valves. The procedures describe disconnecting hoses and electrical connections, removing mounting hardware, and installing components in the reverse order while applying specified torques to fasteners. Safety notices are included regarding hot coolant, fuel leaks, and proper fluid disposal.
Caterpillar cat 730 c ejector articulated truck (prefix tfh) service repair m...fusjekksmewsx
The document provides instructions for removing and installing various components of a 730C Ejector Articulated Truck, including the diesel exhaust fluid tank, pump, injector, electronic control unit, and solenoid valves. The procedures describe disconnecting hoses and electrical connections, removing mounting hardware, and replacing seals before reinstalling components in the reverse order of removal while tightening fasteners to the specified torques. Safety notices are included regarding hot coolant, fuel leaks, and proper fluid disposal.
Caterpillar cat 730 c ejector articulated truck (prefix tfh) service repair m...ufjsjekjkeme
The document provides instructions for removing and installing various components of a 730C Ejector Articulated Truck, including the diesel exhaust fluid tank, pump, injector, electronic control unit, and solenoid valves. The procedures include disconnecting hoses and electrical connections, removing mounting hardware, and installing components in the reverse order while applying specified torques to fasteners. Safety notices are also provided regarding hot coolant, fuel leaks, and contained fluid disposal.
The document is a service repair manual that provides instructions for removing and installing various diesel exhaust fluid (DEF) system components on a 730C Ejector articulated truck. It includes illustrated step-by-step procedures for removing and installing the DEF tank, pump, injector, electronic control module, heater coolant solenoid valve, and fuel solenoid valve. Safety notices are provided and proper torque specifications are listed for reinstallation.
The document is a service repair manual that provides instructions for removing and installing various diesel exhaust fluid (DEF) system components on a 730C Ejector articulated truck. It includes illustrated step-by-step procedures for removing and installing the DEF tank, pump, injector, electronic control module, heater coolant solenoid valve, and fuel solenoid valve. Safety notices are provided and proper torque specifications are listed for reinstallation.
The document is a service repair manual that provides instructions for removing and installing various diesel exhaust fluid (DEF) system components on a 730C Ejector Articulated Truck. It includes illustrated step-by-step procedures for servicing the DEF tank, pump, injector, electronic control module, heater coolant solenoid valve, and ARD fuel solenoid valve. Safety notices are also provided regarding the potential hazards of hot coolant and spilled fuel.
The document provides instructions for removing and assembling a torque converter for a 730C2 articulated truck. It lists the required tools and gives step-by-step procedures with accompanying illustrations. The torque converter components are removed in the order of the housing assembly, piston, plates and discs, turbine, impeller, carrier, and stator parts. Assembly is the reverse of disassembly, with notes to clean parts and apply specified torques.
The document provides instructions for removing and assembling components of the torque converter for a 730C2 Articulated Truck. It lists the required tools and presents step-by-step procedures with accompanying illustrations for removing the torque converter housing, disassembling internal components, and assembling the housing. Key steps include using lifting devices to handle heavy components safely, marking parts for proper reinstallation, and noting torque specifications for fasteners.
Caterpillar cat 730 c ejector articulated truck (prefix tfh) service repair m...fjsekkdkmem
The document provides instructions for removing and installing various components of a 730C Ejector Articulated Truck, including the diesel exhaust fluid tank, pump, injector, electronic control unit, and solenoid valves. The procedures describe disconnecting hoses and electrical connections, removing mounting hardware, and installing components in the reverse order while applying specified torques to fasteners. Safety notices are included regarding hot coolant, fuel leaks, and proper fluid disposal.
Caterpillar cat 730 c ejector articulated truck (prefix tfh) service repair m...fusjekksmewsx
The document provides instructions for removing and installing various components of a 730C Ejector Articulated Truck, including the diesel exhaust fluid tank, pump, injector, electronic control unit, and solenoid valves. The procedures describe disconnecting hoses and electrical connections, removing mounting hardware, and replacing seals before reinstalling components in the reverse order of removal while tightening fasteners to the specified torques. Safety notices are included regarding hot coolant, fuel leaks, and proper fluid disposal.
Caterpillar cat 730 c ejector articulated truck (prefix tfh) service repair m...ufjsjekjkeme
The document provides instructions for removing and installing various components of a 730C Ejector Articulated Truck, including the diesel exhaust fluid tank, pump, injector, electronic control unit, and solenoid valves. The procedures include disconnecting hoses and electrical connections, removing mounting hardware, and installing components in the reverse order while applying specified torques to fasteners. Safety notices are also provided regarding hot coolant, fuel leaks, and contained fluid disposal.
The document is a service repair manual that provides instructions for removing and installing various diesel exhaust fluid (DEF) system components on a 730C Ejector articulated truck. It includes illustrated step-by-step procedures for removing and installing the DEF tank, pump, injector, electronic control module, heater coolant solenoid valve, and fuel solenoid valve. Safety notices are provided and proper torque specifications are listed for reinstallation.
The document is a service repair manual that provides instructions for removing and installing various diesel exhaust fluid (DEF) system components on a 730C Ejector articulated truck. It includes illustrated step-by-step procedures for removing and installing the DEF tank, pump, injector, electronic control module, heater coolant solenoid valve, and fuel solenoid valve. Safety notices are provided and proper torque specifications are listed for reinstallation.
The document is a service repair manual that provides instructions for removing and installing various diesel exhaust fluid (DEF) system components on a 730C Ejector Articulated Truck. It includes illustrated step-by-step procedures for servicing the DEF tank, pump, injector, electronic control module, heater coolant solenoid valve, and ARD fuel solenoid valve. Safety notices are also provided regarding the potential hazards of hot coolant and spilled fuel.
The document provides instructions for removing and assembling a torque converter for a 730C2 articulated truck. It lists the required tools and gives step-by-step procedures with accompanying illustrations. The torque converter components are removed in the order of the housing assembly, piston, plates and discs, turbine, impeller, carrier, and stator parts. Assembly is the reverse of disassembly, with notes to clean parts and apply specified torques.
The document provides instructions for removing and assembling components of the torque converter for a 730C2 Articulated Truck. It lists the required tools and presents step-by-step procedures with accompanying illustrations for removing the torque converter housing, disassembling internal components, and assembling the housing. Key steps include using lifting devices to handle heavy components safely, marking parts for proper reinstallation, and noting torque specifications for fasteners.
The document provides instructions for removing and disassembling a torque converter from a 730C2 articulated truck with a C13 engine. It lists the required tools and presents step-by-step instructions with accompanying illustrations. The instructions describe removing the torque converter housing, then disassembling internal components like the piston, plates, discs, bearings, and impeller. Reassembly instructions are also provided.
The document provides instructions for removing and disassembling a torque converter from a Caterpillar 730C2 articulated truck. It describes 18 steps to disassemble the torque converter and 19 steps to reassemble it. Tools required include an adapter plate, engine stand, oil drain cart, and link brackets. Safety precautions are provided to contain fluids and protect from spring forces.
The document provides instructions for removing and disassembling a torque converter from a 730C2 articulated truck with a C13 engine. It lists the required tools and presents step-by-step instructions with accompanying illustrations. The instructions describe removing the torque converter housing, then disassembling internal components like the piston, plates, discs, bearings, and impeller. Reassembly instructions are also provided.
The document provides instructions for servicing components of the power train for a 730C2 articulated truck. It includes procedures for removing and installing the torque converter housing, relief valve, accessory drive, idler gear, and pump drive. The pump drive removal procedure involves detaching the torque converter housing and shield assembly, then removing bolts and the pump drive unit. The pump drive disassembly requires removing manifold bolts and parts, races, and the carrier assembly.
The document provides instructions for servicing components of the power train for a 730C2 articulated truck. It includes procedures for removing and installing the torque converter housing, relief valve, accessory drive, idler gear, and pump drive. The pump drive removal procedure involves detaching the torque converter housing and shield assembly, then removing bolts and the pump drive unit. The pump drive disassembly requires removing manifold bolts and parts, races, and the carrier assembly.
The document provides instructions for removing and installing various transmission components on a 730C2 articulated truck, including:
1. Removing and installing a torque converter housing, which requires attaching lifting tools and brackets due to the housing's 500 lb weight.
2. Removing and installing a relief valve on the torque converter inlet, which involves removing a manifold, relief valve, and O-ring seal.
3. Removing and installing an accessory drive on the transmission, which requires pressing out and installing bearing cups and removing/installing gears, seals, and shims.
4. Removing and installing an idler gear on the transmission accessory drive, which removes the gear from the housing.
5
The document provides instructions for removing and installing various components of the power train system for a 730C2 articulated truck, including:
1) Removing and installing the torque converter housing, requiring specialized tools and lifting equipment due to the component's weight.
2) Removing and installing the relief valve on the torque converter inlet, which involves removing retaining rings and seals.
3) Removing and installing the transmission accessory drive, a multi-step process that includes pressing out bearings and installing shims to set proper end play.
The document provides instructions for removing and installing various components of the transmission system for a 730C2 Articulated Truck powered by a C13 engine. The first section describes removing the torque converter housing and installing a new housing. The second section explains how to remove and install the relief valve for the torque converter inlet. The third section gives directions for removing and installing the accessory drive component of the transmission.
The document provides instructions for removing and installing various components of the power train system for a 730C2 articulated truck, including:
1) Removing and installing the torque converter housing, requiring specialized tools and lifting equipment due to the component's weight.
2) Removing and installing the relief valve on the torque converter inlet, which involves removing retaining rings and seals.
3) Removing and installing the transmission accessory drive, a multi-step process that includes pressing out bearings and installing shims to set proper end play.
The document provides instructions for removing and installing various powertrain components on a 745C articulated truck, including:
1) Removing and installing the torque converter, which requires using lifting tools and weighs approximately 95 kg.
2) Removing and installing the transmission scavenge pump, which involves disconnecting hoses and removing mounting bolts.
3) Removing and installing the transmission oil filter, which requires releasing system pressure and removing mounting bolts and harnesses.
This document provides instructions for removing and installing the front suspension frame on a 745 Articulated Truck. The removal procedure involves disconnecting hydraulic lines, removing mounting bolts, and using lifting equipment to remove the heavy frame component. The installation procedure is the reverse of removal, and includes priming bearings with grease, tightening bolts to the specified torque values, and reconnecting hydraulic lines. Safety precautions are provided regarding working under heavy components and relieving hydraulic pressure.
This document provides instructions for removing and disassembling the engine and torque converter from a Caterpillar 730C Ejector Articulated Truck. It describes disconnecting wiring harnesses, hoses, brackets, and removing bolts to detach the engine. It then outlines steps to disassemble the torque converter including removing housing, bearings, plates, and seals. The instructions are detailed with illustrations and cautions for safe removal of pressurized components.
This document provides instructions for installing an automatic timing advance and removing a fuel injection pump housing and governor from a Caterpillar 3304B engine. It describes:
1) Using various tools to install the automatic timing advance and tighten bolts to the specified torques.
2) Removing components like lines, covers, and tubes to access the fuel injection pump housing and governor.
3) Using lifting equipment to safely remove the housing and governor assembly due to its weight.
This document provides instructions for servicing the grapple arch cylinder on a 527 Track Skidder. It describes how to remove the cylinder by disconnecting hoses, removing retaining pins, and lifting it from the arch. It then details how to disassemble the cylinder by removing seals and bearings. The assembly process is outlined as well, including installing new seals and bearings and reattaching the cylinder to the arch using retaining pins.
This document provides instructions for removing the transmission from a 432F2 backhoe loader. It describes:
1) Placing jack stands under the front and rear of the loader to lift it 1270 mm off the ground for access.
2) Draining the transmission oil per the operation manual before removal.
3) Removing mounting bolts, brackets, and other hardware to separate the transmission from the loader.
This document provides instructions for removing and installing the flywheel housing and crankshaft front seal on a 3054 engine. It outlines the required tools and safety precautions, and gives a step-by-step process including supporting the engine, removing mounting bolts, lifting the housing off with links, cleaning surfaces, and torquing bolts to specified values. It also describes removing the crankshaft front seal by drilling holes and pulling it out, and installing the new seal by lubricating the lip and pressing it into place.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and safety precautions. The removal procedure involves first removing the electric starting motor and flywheel. For engines with a 14-bolt housing, the housing is then removed by taking out bolts and removing the housing and gasket from dowels in the cylinder block. For engines with a 10-bolt housing, the one-piece housing assembly is removed after loosening bolts in sequence. The installation procedure provides instructions for cleaning parts, placing the housing and seal over a tool, and tightening bolts to the specified torque.
This document provides instructions for removing and installing fuel injection nozzles and inlet and exhaust valve springs on a Caterpillar 3054 engine. The fuel injection nozzle removal procedure involves removing fuel lines, loosening a threaded nut, and removing the nozzle and seat washer. Installation requires cleaning threads, installing a new seat washer, applying anti-seize compound, and tightening the nut. The valve spring procedure requires using a compressor tool to compress springs, removing keepers and retainers, and replacing springs in the reverse order. Tools and torque specifications are provided.
This document provides instructions for removing and installing fuel injection nozzles and fuel injection pumps on a Caterpillar 3054 engine. It describes the required tools and safety precautions. The procedures include removing fuel lines, loosening nuts, removing nozzles and pumps, and installing new seals and washers. Precise positioning and torque specifications are noted to maintain proper timing.
The document provides instructions for removing and installing a hydraulic tank on a 420F backhoe loader. The removal procedure involves:
1. Disconnecting hoses from the hydraulic tank assembly
2. Disconnecting clamps on hoses connected to the tank
3. Removing bolts to detach the tank from the vehicle
4. Removing additional components like a strainer and gauge from the tank. The installation procedure is the reverse of removal.
The document provides instructions for removing and installing a tie rod on the front steering of a 420D backhoe loader. It lists the required tool as a transmission repair stand and instructs the user to first remove the front axle from the machine. Safety precautions are provided to release hydraulic pressure before servicing. Detailed steps are then outlined to remove the tie rod from the axle and install a new one.
This document provides instructions for disassembling and assembling components of a 320C excavator travel motor. The summary is:
1. The travel motor disassembly procedure involves removing bolts, seals, springs, plates, and pistons from the motor housing.
2. Cleaning and applying identification marks to components is important to prevent contamination and ensure correct reassembly.
3. Tools are required to remove some components, including link brackets, slide hammers, bearing pullers, and crossblocks.
More Related Content
Similar to Caterpillar Cat 730C Ejector Articulated Truck (Prefix TFH) Service Repair Manual (TFH00001 and up).pdf
The document provides instructions for removing and disassembling a torque converter from a 730C2 articulated truck with a C13 engine. It lists the required tools and presents step-by-step instructions with accompanying illustrations. The instructions describe removing the torque converter housing, then disassembling internal components like the piston, plates, discs, bearings, and impeller. Reassembly instructions are also provided.
The document provides instructions for removing and disassembling a torque converter from a Caterpillar 730C2 articulated truck. It describes 18 steps to disassemble the torque converter and 19 steps to reassemble it. Tools required include an adapter plate, engine stand, oil drain cart, and link brackets. Safety precautions are provided to contain fluids and protect from spring forces.
The document provides instructions for removing and disassembling a torque converter from a 730C2 articulated truck with a C13 engine. It lists the required tools and presents step-by-step instructions with accompanying illustrations. The instructions describe removing the torque converter housing, then disassembling internal components like the piston, plates, discs, bearings, and impeller. Reassembly instructions are also provided.
The document provides instructions for servicing components of the power train for a 730C2 articulated truck. It includes procedures for removing and installing the torque converter housing, relief valve, accessory drive, idler gear, and pump drive. The pump drive removal procedure involves detaching the torque converter housing and shield assembly, then removing bolts and the pump drive unit. The pump drive disassembly requires removing manifold bolts and parts, races, and the carrier assembly.
The document provides instructions for servicing components of the power train for a 730C2 articulated truck. It includes procedures for removing and installing the torque converter housing, relief valve, accessory drive, idler gear, and pump drive. The pump drive removal procedure involves detaching the torque converter housing and shield assembly, then removing bolts and the pump drive unit. The pump drive disassembly requires removing manifold bolts and parts, races, and the carrier assembly.
The document provides instructions for removing and installing various transmission components on a 730C2 articulated truck, including:
1. Removing and installing a torque converter housing, which requires attaching lifting tools and brackets due to the housing's 500 lb weight.
2. Removing and installing a relief valve on the torque converter inlet, which involves removing a manifold, relief valve, and O-ring seal.
3. Removing and installing an accessory drive on the transmission, which requires pressing out and installing bearing cups and removing/installing gears, seals, and shims.
4. Removing and installing an idler gear on the transmission accessory drive, which removes the gear from the housing.
5
The document provides instructions for removing and installing various components of the power train system for a 730C2 articulated truck, including:
1) Removing and installing the torque converter housing, requiring specialized tools and lifting equipment due to the component's weight.
2) Removing and installing the relief valve on the torque converter inlet, which involves removing retaining rings and seals.
3) Removing and installing the transmission accessory drive, a multi-step process that includes pressing out bearings and installing shims to set proper end play.
The document provides instructions for removing and installing various components of the transmission system for a 730C2 Articulated Truck powered by a C13 engine. The first section describes removing the torque converter housing and installing a new housing. The second section explains how to remove and install the relief valve for the torque converter inlet. The third section gives directions for removing and installing the accessory drive component of the transmission.
The document provides instructions for removing and installing various components of the power train system for a 730C2 articulated truck, including:
1) Removing and installing the torque converter housing, requiring specialized tools and lifting equipment due to the component's weight.
2) Removing and installing the relief valve on the torque converter inlet, which involves removing retaining rings and seals.
3) Removing and installing the transmission accessory drive, a multi-step process that includes pressing out bearings and installing shims to set proper end play.
Similar to Caterpillar Cat 730C Ejector Articulated Truck (Prefix TFH) Service Repair Manual (TFH00001 and up).pdf (9)
The document provides instructions for removing and installing various powertrain components on a 745C articulated truck, including:
1) Removing and installing the torque converter, which requires using lifting tools and weighs approximately 95 kg.
2) Removing and installing the transmission scavenge pump, which involves disconnecting hoses and removing mounting bolts.
3) Removing and installing the transmission oil filter, which requires releasing system pressure and removing mounting bolts and harnesses.
This document provides instructions for removing and installing the front suspension frame on a 745 Articulated Truck. The removal procedure involves disconnecting hydraulic lines, removing mounting bolts, and using lifting equipment to remove the heavy frame component. The installation procedure is the reverse of removal, and includes priming bearings with grease, tightening bolts to the specified torque values, and reconnecting hydraulic lines. Safety precautions are provided regarding working under heavy components and relieving hydraulic pressure.
This document provides instructions for removing and disassembling the engine and torque converter from a Caterpillar 730C Ejector Articulated Truck. It describes disconnecting wiring harnesses, hoses, brackets, and removing bolts to detach the engine. It then outlines steps to disassemble the torque converter including removing housing, bearings, plates, and seals. The instructions are detailed with illustrations and cautions for safe removal of pressurized components.
This document provides instructions for installing an automatic timing advance and removing a fuel injection pump housing and governor from a Caterpillar 3304B engine. It describes:
1) Using various tools to install the automatic timing advance and tighten bolts to the specified torques.
2) Removing components like lines, covers, and tubes to access the fuel injection pump housing and governor.
3) Using lifting equipment to safely remove the housing and governor assembly due to its weight.
This document provides instructions for servicing the grapple arch cylinder on a 527 Track Skidder. It describes how to remove the cylinder by disconnecting hoses, removing retaining pins, and lifting it from the arch. It then details how to disassemble the cylinder by removing seals and bearings. The assembly process is outlined as well, including installing new seals and bearings and reattaching the cylinder to the arch using retaining pins.
This document provides instructions for removing the transmission from a 432F2 backhoe loader. It describes:
1) Placing jack stands under the front and rear of the loader to lift it 1270 mm off the ground for access.
2) Draining the transmission oil per the operation manual before removal.
3) Removing mounting bolts, brackets, and other hardware to separate the transmission from the loader.
This document provides instructions for removing and installing the flywheel housing and crankshaft front seal on a 3054 engine. It outlines the required tools and safety precautions, and gives a step-by-step process including supporting the engine, removing mounting bolts, lifting the housing off with links, cleaning surfaces, and torquing bolts to specified values. It also describes removing the crankshaft front seal by drilling holes and pulling it out, and installing the new seal by lubricating the lip and pressing it into place.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and safety precautions. The removal procedure involves first removing the electric starting motor and flywheel. For engines with a 14-bolt housing, the housing is then removed by taking out bolts and removing the housing and gasket from dowels in the cylinder block. For engines with a 10-bolt housing, the one-piece housing assembly is removed after loosening bolts in sequence. The installation procedure provides instructions for cleaning parts, placing the housing and seal over a tool, and tightening bolts to the specified torque.
This document provides instructions for removing and installing fuel injection nozzles and inlet and exhaust valve springs on a Caterpillar 3054 engine. The fuel injection nozzle removal procedure involves removing fuel lines, loosening a threaded nut, and removing the nozzle and seat washer. Installation requires cleaning threads, installing a new seat washer, applying anti-seize compound, and tightening the nut. The valve spring procedure requires using a compressor tool to compress springs, removing keepers and retainers, and replacing springs in the reverse order. Tools and torque specifications are provided.
This document provides instructions for removing and installing fuel injection nozzles and fuel injection pumps on a Caterpillar 3054 engine. It describes the required tools and safety precautions. The procedures include removing fuel lines, loosening nuts, removing nozzles and pumps, and installing new seals and washers. Precise positioning and torque specifications are noted to maintain proper timing.
The document provides instructions for removing and installing a hydraulic tank on a 420F backhoe loader. The removal procedure involves:
1. Disconnecting hoses from the hydraulic tank assembly
2. Disconnecting clamps on hoses connected to the tank
3. Removing bolts to detach the tank from the vehicle
4. Removing additional components like a strainer and gauge from the tank. The installation procedure is the reverse of removal.
The document provides instructions for removing and installing a tie rod on the front steering of a 420D backhoe loader. It lists the required tool as a transmission repair stand and instructs the user to first remove the front axle from the machine. Safety precautions are provided to release hydraulic pressure before servicing. Detailed steps are then outlined to remove the tie rod from the axle and install a new one.
This document provides instructions for disassembling and assembling components of a 320C excavator travel motor. The summary is:
1. The travel motor disassembly procedure involves removing bolts, seals, springs, plates, and pistons from the motor housing.
2. Cleaning and applying identification marks to components is important to prevent contamination and ensure correct reassembly.
3. Tools are required to remove some components, including link brackets, slide hammers, bearing pullers, and crossblocks.
This document provides instructions for removing and disassembling the water pump on a Caterpillar 320C excavator engine. The key steps include:
1. Draining the coolant and removing the V-belts.
2. Removing four bolts to separate the water pump, pulley, and O-ring from the engine.
3. Heating the water pump to 80°C to make disassembly easier, then removing four bolts and the pulley from the pump housing.
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
Caterpillar Cat 320C L Excavator (Prefix JTG) Service Repair Manual (JTG00001...f8usjejkdmmd
The documents provide instructions for servicing the travel motor of a 320C excavator, including removing and installing the counterbalance valve, removing and disassembling the travel motor, and assembling the travel motor. The documents describe each step in detail and include illustrations to identify the relevant components. Proper cleaning, containment of fluids, and replacement of O-rings are emphasized throughout.
Caterpillar Cat 320C L Excavator (Prefix MAB) Service Repair Manual (MAB00001...f8usjejkdmmd
This document provides instructions for disassembling a recoil spring assembly. It begins by removing the front idler and recoil spring assembly from the machine. A specialized recoil spring bench tool is then used to disassemble the recoil spring. The spring is under high tension and special precautions are required when handling it. The tool supports the spring and allows the retaining nut to be safely removed with a hydraulic cylinder, releasing the compressed spring.
The documents provide instructions for servicing components of a 320C excavator, including installing a counterbalance valve, removing and disassembling the travel motor, and assembling the travel motor. The documents describe cleaning parts and containing fluids, detail the required tools, and outline the step-by-step processes for installing, removing, and disassembling/assembling various components while taking appropriate safety precautions.
Caterpillar Cat 320C L Excavator (Prefix DBG) Service Repair Manual (DBG00001...f8usjejkdmmd
This document provides instructions for removing and installing various components of a Caterpillar 3066 engine, including the flywheel, crankshaft rear seal, crankshaft pulley, and flywheel housing. The procedures describe using various tools to remove and install each part, providing details on cleaning, inspection, and torque specifications. Safety notices are also included to keep parts clean and contain fluids.
This document provides instructions for disassembling a recoil spring assembly. It begins by removing the front idler and recoil spring assembly from the machine. A specialized recoil spring bench tool is then used to disassemble the recoil spring. The spring is under high tension and special precautions are required when handling it. The tool supports the spring and allows removing the retaining nut safely to separate the spring from other components.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
9. Illustration 15 g06039902
Note: Place identification marks on DEF pump coolant connectors (23) and DEF pump
connectors (24) for installation purposes. DEF pump coolant connectors (23) and DEF
pump connectors (24) are not interchangeable.
15. Remove DEF pump coolant connectors (23) and DEF pump connectors (24) from diesel
exhaust fluid pump (22).
Illustration 16 g06039906
16. Remove filter (25).
Installation Procedure
1. Install diesel exhaust fluid pump (22) in the reverse order of removal.
a. DEF pump connectors (24) to a torque of 4.5 ± 0.5 N·m (40± 4 lb in).
b. Tighten DEF pump coolant connectors (23) to a torque of 5.5 ± 0.5 N·m
(48 ± 4 lb in).
c. Tighten cover (20) to a torque of 20 ± 5 N·m (177 ± 44 lb in).
d. Tighten bolts (21) to a torque of 19 ± 2 N·m (168 ± 18 lb in).
e. Tighten bolts (16), (17) and (18) to a torque of 4 ± 0.7 N·m (35 ± 6 lb in).
6/7
730C Ejector Articulated Truck TFH00001-UP (MACHINE) POWERED BY C13 En...
2019/12/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: EJECTOR TRUCK
Model: 730C EJECTOR TRUCK TFH
Configuration: 730C Ejector Articulated Truck TFH00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
730C and 730C EJECTOR Articulated Trucks
Media Number -UENR2343-01 Publication Date -01/10/2014 Date Updated -29/03/2016
i05829507
Diesel Exhaust Fluid Injector - Remove and Install
SMCS - 108I-010; 108K-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 385-1861 Connector Plug 2
B - LOCTITE C-5A Copper Antiseize -
Illustration 1 g03687664
1. Disconnect hose assemblies (1) and cap with Tooling (A). Disconnect hose assembly (2).
1/2
730C Ejector Articulated Truck TFH00001-UP (MACHINE) POWERED BY C13 En...
2019/12/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 2 g03687850
2. Disconnect harness assembly (4). Remove bolts (3) and remove diesel exhaust fluid injector
(5).
Illustration 3 g03687863
3. Remove gasket (6). Remove seal (7) from diesel exhaust fluid injector (5).
Installation Procedure
1. Install diesel exhaust fluid injector (5) in the reverse order of removal.
a. Replace gasket (6) and seal (7).
b. Apply Tooling (B) to the threads of bolts (3). Tighten bolts (3) to a torque of
5 ± 0.5 N·m (44 ± 4 lb in).
c. Retorque bolts (3) and turn an additional 90° ± 5°.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Dec 26 00:13:29 UTC+0800 2019
2/2
730C Ejector Articulated Truck TFH00001-UP (MACHINE) POWERED BY C13 En...
2019/12/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EJECTOR TRUCK
Model: 730C EJECTOR TRUCK TFH
Configuration: 730C Ejector Articulated Truck TFH00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
730C and 730C EJECTOR Articulated Trucks
Media Number -UENR2343-01 Publication Date -01/10/2014 Date Updated -29/03/2016
i05829892
Electronic Control (Diesel Exhaust Fluid) - Remove and
Install
SMCS - 108K-010-EK2
Removal Procedure
Illustration 1 g03687979
Note: Use locking tabs (1) to remove and install harness assemblies (2). Pull out locking
tabs (1) to remove harness assemblies (2). Push in locking tabs (1) to install harness
assemblies (2).
1. Disconnect harness assemblies (2) and remove bolts (4). Remove electronic control (3).
Installation Procedure
1. Install electronic control (3) in the reverse order of removal.
a. Tighten bolts (4) to a torque of 10 ± 2 N·m (89 ± 18 lb in).
1/2
730C Ejector Articulated Truck TFH00001-UP (MACHINE) POWERED BY C13 En...
2019/12/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: EJECTOR TRUCK
Model: 730C EJECTOR TRUCK TFH
Configuration: 730C Ejector Articulated Truck TFH00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
730C and 730C EJECTOR Articulated Trucks
Media Number -UENR2343-01 Publication Date -01/10/2014 Date Updated -29/03/2016
i05829939
Solenoid Valve (DEF Heater Coolant) - Remove and Install
SMCS - 5479-CLT
Removal Procedure
Personal injury can result from hot coolant, steam and alkali.
At operating temperature, engine coolant is hot and under pressure. The
radiator and all lines to heaters or the engine contain hot coolant or
steam. Any contact can cause severe burns.
Remove cooling system pressure cap slowly to relieve pressure only
when engine is stopped and cooling system pressure cap is cool enough
to touch with your bare hand.
Do not attempt to tighten hose connections when the coolant is hot, the
hose can come off causing burns.
Cooling System Coolant Additive contains alkali. Avoid contact with
skin and eyes.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/2
730C Ejector Articulated Truck TFH00001-UP (MACHINE) POWERED BY C13 En...
2019/12/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g03688007
1. Disconnect harness assembly (1). Disconnect tubes (2).
Illustration 2 g03685247
2. Remove bolts (4) and remove solenoid valve (3).
Installation Procedure
1. Install solenoid valve (3) in the reverse order of removal.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Dec 26 00:15:20 UTC+0800 2019
2/2
730C Ejector Articulated Truck TFH00001-UP (MACHINE) POWERED BY C13 En...
2019/12/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: EJECTOR TRUCK
Model: 730C EJECTOR TRUCK TFH
Configuration: 730C Ejector Articulated Truck TFH00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
730C and 730C EJECTOR Articulated Trucks
Media Number -UENR2343-01 Publication Date -01/10/2014 Date Updated -29/03/2016
i05829980
Solenoid Valve (ARD Fuel) - Remove and Install
SMCS - 5479-010
Removal Procedure (Pilot)
Personal injury or death may result from failure to adhere to the
following procedures.
Fuel leaked or spilled onto hot surfaces or electrical components can
cause a fire.
Clean up all leaked or spilled fuel. Do not smoke while working on the
fuel system.
Turn the disconnect switch OFF or disconnect the battery when
changing fuel filters.
1/3
730C Ejector Articulated Truck TFH00001-UP (MACHINE) POWERED BY C13 En...
2019/12/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 1 g03688030
Illustration 2 g02798233
1. Use the following steps to remove solenoid valve assembly (1).
2. Remove nut (6) and washer (5).
3. Remove solenoid (4)
4. Remove cartridge assembly (3) and O-ring seals (2).
Installation Procedure
1. Install solenoid valve assembly (1) in the reverse order of removal.
a. Tighten cartridge assembly (3) to a torque of 50 ± 5 N·m (37 ± 4 lb ft).
b. Tighten nut (6) to a torque of 20 ± 2.5 N·m (177 ± 22 lb in).
Removal Procedure (Main)
Personal injury or death may result from failure to adhere to the
following procedures.
Fuel leaked or spilled onto hot surfaces or electrical components can
cause a fire.
Clean up all leaked or spilled fuel. Do not smoke while working on the
fuel system.
Turn the disconnect switch OFF or disconnect the battery when
changing fuel filters.
2/3
730C Ejector Articulated Truck TFH00001-UP (MACHINE) POWERED BY C13 En...
2019/12/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
18. Illustration 3 g03688075
Illustration 4 g02798233
1. Use the following steps to remove solenoid valve assembly (1).
2. Remove nut (6) and washer (5).
3. Remove solenoid (4)
4. Remove cartridge assembly (3) and O-ring seals (2).
Installation Procedure
1. Install solenoid valve assembly (1) in the reverse order of removal.
a. Tighten cartridge assembly (3) to a torque of 50 ± 5 N·m (37 ± 4 lb ft).
b. Tighten nut (6) to a torque of 20 ± 2.5 N·m (177 ± 22 lb in).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Dec 26 00:16:16 UTC+0800 2019
3/3
730C Ejector Articulated Truck TFH00001-UP (MACHINE) POWERED BY C13 En...
2019/12/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: EJECTOR TRUCK
Model: 730C EJECTOR TRUCK TFH
Configuration: 730C Ejector Articulated Truck TFH00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
730C and 730C EJECTOR Articulated Trucks
Media Number -UENR2343-01 Publication Date -01/10/2014 Date Updated -29/03/2016
i05831007
Pressure Sensor (ARD Main Fuel) - Remove and Install
SMCS - 1439-010
Removal Procedure
Personal injury or death may result from failure to adhere to the
following procedures.
Fuel leaked or spilled onto hot surfaces or electrical components can
cause a fire.
Clean up all leaked or spilled fuel. Do not smoke while working on the
fuel system.
Turn the disconnect switch OFF or disconnect the battery when
changing fuel filters.
1/2
730C Ejector Articulated Truck TFH00001-UP (MACHINE) POWERED BY C13 En...
2019/12/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 1 g03688694
1. Disconnect harness assembly (2). Remove pressure sensor (1).
Installation Procedure
1. Install pressure sensor (1) in the reverse order of removal.
a. Tighten pressure sensor (1) to a torque of 30 ± 3 N·m (22 ± 2 lb ft).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Dec 26 00:17:12 UTC+0800 2019
2/2
730C Ejector Articulated Truck TFH00001-UP (MACHINE) POWERED BY C13 En...
2019/12/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: EJECTOR TRUCK
Model: 730C EJECTOR TRUCK TFH
Configuration: 730C Ejector Articulated Truck TFH00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
730C and 730C EJECTOR Articulated Trucks
Media Number -UENR2343-01 Publication Date -01/10/2014 Date Updated -29/03/2016
i05831302
Pressure Sensor (ARD Pilot Fuel) - Remove and Install
SMCS - 1439-010
Removal Procedure
Personal injury or death may result from failure to adhere to the
following procedures.
Fuel leaked or spilled onto hot surfaces or electrical components can
cause a fire.
Clean up all leaked or spilled fuel. Do not smoke while working on the
fuel system.
Turn the disconnect switch OFF or disconnect the battery when
changing fuel filters.
1/2
730C Ejector Articulated Truck TFH00001-UP (MACHINE) POWERED BY C13 En...
2019/12/26
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...