Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
What Does the Active Steering Malfunction Warning Mean for Your BMWTanner Motors
Discover the reasons why your BMW’s Active Steering malfunction warning might come on. From electrical glitches to mechanical failures and software anomalies, addressing these promptly with professional inspection and maintenance ensures continued safety and performance on the road, maintaining the integrity of your driving experience.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
2. Shutdown SIS
Previous Screen
Product: WHEEL TRACTOR-SCRAPER
Model: 637K WHEEL TRACTOR-SCRAPER WTS
Configuration: 637K Wheel Tractor Scraper WTS00001-UP (MACHINE)
Disassembly and Assembly
631K and 637K Wheel Tractor Scraper Power Train
Media Number -M0067918-02 Publication Date -01/03/2018 Date Updated -03/04/2018
i02176953
Torque Converter - Disassemble
SMCS - 3101-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 2P-8312 Retaining Ring Pliers 1
B 1P-0510 Driver Group 1
C -
Forcing Bolts
3/8 - 16 NC by 4 inch
2
Start By:
a. Remove the torque converter. Refer to Disassembly and Assembly, "Torque Converter -
Remove".
1/7(W)
w
2021/8/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. Illustration 1 g01102574
1. Use Tooling (A) in order to remove retaining ring (1) from carriage support assembly (2).
Remove carriage support assembly (2) from hub (3). Use Tooling (B) and a suitable
hydraulic press in order to remove the sleeve bearing from carriage support assembly (2).
Illustration 2 g01102576
2. Remove bolts (4) from impeller (5). Remove bolts (6) and clamp plate (7) from impeller
hub (8).
Illustration 3 g01102575
3. Install Tooling (C) into impeller (5). Use Tooling (C) in order to remove impeller (5) and
impeller hub (8) from housing (9).
2/7(W)
w
2021/8/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. Illustration 4 g00525305
4. Remove thrust race (10) from impeller (5). Remove impeller hub (8) from impeller (5).
Illustration 5 g01108447
5. Remove thrust bearing (11) and seal ring (12A) from carrier assembly (12).
Illustration 6 g00525308
6. Remove carrier assembly (12) and stator (13) as a unit from housing (9).
3/7(W)
w
2021/8/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. Illustration 7 g01102577
7. Position carrier assembly (12) and stator (13), as shown. Use Tooling (A) in order to
remove retaining ring (14) from stator (13). Remove thrust race (15) from stator (13).
Illustration 8 g01102579
8. Remove freewheel rollers (17) and freewheel springs (16) from freewheel cam (18).
Remove stator (13) from carrier assembly (12).
Illustration 9 g01102580
9. Use Tooling (A) in order to remove retaining ring (19) from stator (13). Remove side plate
(20) from stator (13).
4/7(W)
w
2021/8/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. 10. Use Tooling (B) and a suitable press in order to remove freewheel cam (18) from stator
(13).
Illustration 10 g01102581
11. Remove thrust bearing (21) from carrier assembly (12). Remove sleeve bearing (22) from
carrier assembly (12).
Illustration 11 g00525315
12. Remove turbine (23) and hub (3) as a unit from housing (9).
Illustration 12 g01102582
5/7(W)
w
2021/8/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. 13. Remove thrust bearing (24) and thrust race (25) from hub (3).
Illustration 13 g00525320
14. Position turbine (23), as shown. Remove thrust race (26) from hub (3). Put an alignment
mark on turbine (23) and hub (3) for installation purposes. Remove bolts (27) from turbine
(23).
Illustration 14 g00525321
15. Remove clamp ring (28) and turbine (23) from hub (3).
Illustration 15 g00525322
6/7(W)
w
2021/8/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. 16. Remove thrust bearing (29) and thrust race (30) from housing (9).
Illustration 16 g00528612
17. Remove bolts (31) and flange (32) from housing (9).
Illustration 17 g01102583
18. Remove sleeve bearing (33) from flange (32).
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Aug 29 10:54:25 UTC+0800 2021
7/7(W)
w
2021/8/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. Shutdown SIS
Previous Screen
Product: WHEEL TRACTOR-SCRAPER
Model: 637K WHEEL TRACTOR-SCRAPER WTS
Configuration: 637K Wheel Tractor Scraper WTS00001-UP (MACHINE)
Disassembly and Assembly
631K and 637K Wheel Tractor Scraper Power Train
Media Number -M0067918-02 Publication Date -01/03/2018 Date Updated -03/04/2018
i04351575
Torque Converter - Disassemble - Scraper
SMCS - 3101-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Brackets 3
B 1P-2420 Transmission Repair Stand 1
C 1P-0520 Driver Gp 1
D 8H-0663 Bearing Puller Gp 1
E
1P-2322 Combination Puller 1
1P-0546 Puller Jaw 1
1P-0510 Driver Gp 1
F 1P-0074 Slide Hammer Puller Gp 1
Start By:
a. Separate Torque Converter, Transmission, and Transfer Gear.
1/10(W)
w
2021/8/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. Illustration 1 g02477139
Illustration 2 g02477145
1. Attach Tooling (A) and a suitable lifting device to housing assembly (2) . Reposition
housing assembly (2) onto Tooling (B). The weight of housing assembly (2) is
approximately 73 kg (160 lb).
2. Remove bolts (1) and lift housing assembly (2) from torque converter assembly (3).
Illustration 3 g02477249
3. Reposition torque converter assembly (3) on Tooling (B) as shown. The weight of torque
converter assembly (3) is approximately 34 kg (76 lb).
2/10(W)
w
2021/8/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. 4. Remove bolts (4).
Illustration 4 g02477847
5. Attach Tooling (A) and a suitable lifting device to cover assembly (5). Remove cover
assembly (5) from torque converter assembly (3).
Illustration 5 g02494878
6. Remove clutch piston (6).
Illustration 6 g02495236
3/10(W)
w
2021/8/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. 7. Remove friction disk (7). Remove bolts (10) and shaft retainer (8). Remove hub (9) and seal
rings.
Illustration 7 g02487237
Illustration 8 g02491136
8. Remove bolts (12). Remove bearing retainer (11). Remove retaining ring (13). Remove
upper bearing race (16). Remove retaining ring (14). Remove bearing (15).
Illustration 9 g02487278
9. Reposition torque converter assembly (3) on Tooling (B) as shown. The weight of torque
converter assembly (3) is approximately 34 kg (76 lb).
4/10(W)
w
2021/8/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. 10. Remove bolts (17).
Illustration 10 g02494482
11. Attach Tooling (A) to impeller wheel assembly (18). Remove impeller wheel assembly (18).
The weight of impeller wheel assembly (18) is approximately 34 kg (76 lb).
Illustration 11 g02484296
12. Remove retaining ring (19) from bearing (20).
Illustration 12 g02488758
5/10(W)
w
2021/8/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. 13. Use Tooling (E) to separate shaft assembly (21) from bearing assembly (20) and carrier
assembly (22).
Illustration 13 g02492076
Illustration 14 g02488997
14. Remove bolts (23). Use Tooling (F) to remove stator assembly (24) from carrier assembly
(22) and impeller wheel assembly (18).
Illustration 15 g02489038
6/10(W)
w
2021/8/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Illustration 16 g02489042
15. Remove bolts (25). Use Tooling (C) to remove carrier assembly (22) from impeller wheel
assembly (18).
Illustration 17 g02489047
16. Using Tooling (C) and a suitable press to remove bearing (26) and gear (27) from carrier
assembly (22).
Illustration 18 g02489056
17. Remove seal ring (28).
7/10(W)
w
2021/8/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Illustration 19 g02492176
18. Remove seal rings (29). Remove retaining ring (30) from shaft assembly (21).
Illustration 20 g02489277
Illustration 21 g02489280
19. Install Tooling (D).
Note: Tooling (D) must be seated on the shoulder of turbine (31) in order to support turbine
and prevent damage. Tooling (D) must not contact the splines on shaft (21).
8/10(W)
w
2021/8/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. 20. Use a suitable press to remove shaft assembly (21) from turbine (31). Remove bearing race
(32) and the spacer from turbine (31).
Illustration 22 g02492441
21. Position housing assembly (2) as shown.
22. Remove bolts (33) and gear (34).
Illustration 23 g02492458
23. Remove retaining rings (35) from gear (34).
Illustration 24 g02492476
9/10(W)
w
2021/8/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. 24. Use a suitable press and Tooling (C) in order to remove bearing (36) and shaft from gear
(34).
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Aug 29 10:55:21 UTC+0800 2021
10/10(W)
w
2021/8/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Shutdown SIS
Previous Screen
Product: WHEEL TRACTOR-SCRAPER
Model: 637K WHEEL TRACTOR-SCRAPER WTS
Configuration: 637K Wheel Tractor Scraper WTS00001-UP (MACHINE)
Disassembly and Assembly
631K and 637K Wheel Tractor Scraper Power Train
Media Number -M0067918-02 Publication Date -01/03/2018 Date Updated -03/04/2018
i04578058
Torque Converter - Assemble - Scraper
SMCS - 3101-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Brackets 3
B 1P-2420 Transmission Repair Stand 1
C 1P-0520 Driver Gp 1
G -
Threaded Rod
3/8-16 by 4.00
1
H - Locktite 242 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/12(W)
w
2021/8/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. Illustration 1 g02492476
1. Use a suitable press and Tooling (C) to install bearing (36) and shaft into gear (34).
Illustration 2 g02492458
2. Install retaining ring (35) on each side of gear (34) .
Illustration 3 g02492441
3. Position housing assembly (2) as shown.
2/12(W)
w
2021/8/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. 4. Install gear (34). Install bolts (33) .
Illustration 4 g02492617
5. Lower the temperature of shaft assembly (21). Install retaining ring (30). Install shaft
assembly (21) in the turbine (31) until ring (30) rests on the turbine (31). Install seal rings
(29) .
Illustration 5 g02492679
6. Install the spacer. Raise the temperature of bearing race (32). Install bearing race (32) on
shaft assembly (21) .
3/12(W)
w
2021/8/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Illustration 6 g02489056
7. Install seal ring (28) .
Illustration 7 g02482957
8. Install gear (27) to carrier assembly (22) .
Illustration 8 g02482978
9. Raise the temperature of bearing (26). Install bearing (26) on carrier assembly (22) .
4/12(W)
w
2021/8/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. Illustration 9 g02483898
Illustration 10 g02483903
10. Position lower part of carrier assembly (22) under impeller wheel assembly (18) .
11. Install Tooling (G) to align carrier assembly (22) with impeller wheel assembly (18) .
Illustration 11 g02483983
5/12(W)
w
2021/8/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
24. 12. Install bolts (25). Tighten bolts (25) to a torque of 50 ± 7 N·m (37 ± 5 lb ft).
Illustration 12 g02492076
13. Position stator assembly (24) on carrier assembly (22). Apply Tooling (H) to bolts (23).
Install bolts (23). Tighten bolts (23) to a torque of 40 ± 5 N·m (30 ± 4 lb ft).
Illustration 13 g02484278
14. Install carrier assembly (22) and impeller wheel assembly (18) on turbine (31) and shaft
assembly (21) .
6/12(W)
w
2021/8/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
25. Illustration 14 g02484377
Note: Install bearing (20) with Radius Side (X) facing down, toward carrier assembly (22).
Illustration 15 g02484296
15. Raise the temperature of bearing (20). Install bearing. Install retaining ring (19) .
Illustration 16 g02487297
7/12(W)
w
2021/8/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
26. 16. Attach Tooling (A) and a suitable lifting device to impeller wheel assembly (18). The
weight of impeller wheel assembly (18) is approximately 34 kg (76 lb). Install impeller
wheel assembly (18) into torque converter assembly (3) .
Illustration 17 g02487278
17. Install bolts (17). Tighten bolts (17) to a torque of 30 ± 5 N·m (22 ± 4 lb ft).
18. Reposition torque converter assembly (3) on Tooling (B). The weight of torque converter
assembly (3) is approximately 64 kg (142 lb).
Illustration 18 g02491136
19. Lower the temperature of bearing (15) and install bearing. Install retaining ring (14). Install
upper bearing race (16) and retaining ring (13) .
8/12(W)
w
2021/8/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
27. Illustration 19 g02487237
20. Install bearing retainer (11). Install bolts (12). Tighten bolts (12) to a torque of 50 ± 7 N·m
(37 ± 5 ft).
Illustration 20 g02495236
21. Install hub (9). Install shaft retainer (8) and the seal rings. Install bolts (10). Tighten bolts
(10) to a torque of 50 ± 7 N·m (37 ± 5 lb ft). Install friction disk (7) .
Illustration 21 g02494878
9/12(W)
w
2021/8/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
28. 22. Install clutch piston (6) .
Illustration 22 g02495556
Note: When lowering cover assembly (5) down over clutch piston (6), align pins in cover
assembly (5) into notch on clutch piston (6).
Illustration 23 g02477847
23. Attach Tooling (A) and a suitable lifting device to cover assembly (5). Install cover
assembly (5) into torque converter assembly (3) .
10/12(W)
w
2021/8/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
29. Illustration 24 g02494257
24. Install bolts (4). Tighten bolts (4) to a torque of 50 ± 7 N·m (37 ± 5 lb ft).
Illustration 25 g02477145
Illustration 26 g02477139
25. Attach Tooling (A) and a suitable lifting device to housing assembly (2). The weight of
housing assembly (2) is approximately 119 kg (263 lb). Lower housing assembly (2) onto
torque converter assembly (3). Install bolts (1) .
11/12(W)
w
2021/8/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
30. End By: Connect the torque converter, transmission, and transfer gear.
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Aug 29 10:56:09 UTC+0800 2021
12/12(W)
w
2021/8/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
31. Shutdown SIS
Previous Screen
Product: WHEEL TRACTOR-SCRAPER
Model: 637K WHEEL TRACTOR-SCRAPER WTS
Configuration: 637K Wheel Tractor Scraper WTS00001-UP (MACHINE)
Disassembly and Assembly
631K and 637K Wheel Tractor Scraper Power Train
Media Number -M0067918-02 Publication Date -01/03/2018 Date Updated -03/04/2018
i06636123
Torque Converter - Assemble
SMCS - 3101-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 2P-8312 Retaining Ring Pliers 1
B 1P-0510 Driver Group 1
Illustration 1 g00528674
1. Use Tooling (B) and a suitable hydraulic press to install sleeve bearing (33) into flange (32).
1/7(W)
w
2021/8/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
32. Illustration 2 g00528612
2. Position flange (32) and install bolts (31) onto housing (9). Tighten bolts (31) to a torque of
120 ± 15 N·m (89 ± 11 lb ft).
Illustration 3 g00525322
3. Install thrust bearing (29) and thrust race (30) into housing (9).
Illustration 4 g00525321
4. Install turbine (23) and clamp ring (28) onto hub (3).
2/7(W)
w
2021/8/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
33. Illustration 5 g00525320
5. Install bolts (27) into turbine (23). Tighten bolts (27) to a torque of 50 ± 7 N·m
(37 ± 5 lb ft). Install thrust race (26) onto hub (3).
Illustration 6 g01102582
6. Install thrust race (25) and thrust bearing (24) onto hub (3).
Illustration 7 g00525315
7. Install turbine (23) and hub (3) as a unit into housing (9).
3/7(W)
w
2021/8/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
34. Illustration 8 g00528953
8. Use Tooling (B) and a suitable press to install sleeve bearing (22) into carrier assembly (12).
Install thrust bearing (21) onto carrier assembly (12).
Illustration 9 g01110492
9. Install side plate (20) to stator (13). Use Tooling (A) to install retaining ring (19) to stator
(13).
Illustration 10 g01102579
10. Use Tooling (B) and a suitable hydraulic press to install freewheel cam (18) into stator (13).
4/7(W)
w
2021/8/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
35. 11. Install stator (13) to carrier assembly (12). Install freewheel springs (16) and freewheel
rollers (17) to freewheel cam (18). Always install new freewheel springs (16) and freewheel
rollers (17). Install freewheel springs (16) with the maximum number of loops in freewheel
springs (16) to the outside of freewheel cam (18). Stator (13) should turn freely in the
clockwise direction. Stator (13) should not turn freely in the counterclockwise direction.
Illustration 11 g01110494
12. Install thrust race (15) to stator (13). Use Tooling (A) to install retaining ring (14) onto
stator (13).
Illustration 12 g00525308
13. Install carrier assembly (12) and stator (13) as a unit into housing (9).
5/7(W)
w
2021/8/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
36. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
37. Illustration 13 g01108447
14. Install thrust bearing (11) and seal ring (12A) onto carrier assembly (12).
Illustration 14 g00525305
15. Install impeller hub (8) to impeller (5). Install thrust race (10) onto impeller (5).
Illustration 15 g01102576
16. Install clamp plate (7) and bolts (6) onto impeller hub (8). Tighten bolts (6) to a torque of
50 ± 7 N·m (37 ± 5 lb ft).
17. Install bolts (4) into impeller (5). Tighten bolts (4) to a torque of 50 ± 7 N·m (37 ± 5 lb ft).
6/7(W)
w
2021/8/29
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...