aksi nyata sosialisasi Profil Pelajar Pancasila.pdf
Tugas jarkom router 3 1235010002
1. TUGAS
JARINGAN KOMPUTER
MENGHUBUNGKAN 3 JARINGAN DENGAN 3 BUAH ROUTER
NAMA :
ABRIANTO NUGRAHA ( 1235010002 )
SISTEM INFORMASI – FTI
UNIVERSITAS PEMBANGUNAN NASIONAL “VETERAN” JATIM
2014
2. Cara menghubungkan 3 Router
1. Kita buat dulu desainnya seperti gambar ini (untuk tiap devicenya pakai yang generic)
3. 2. Atur IP Addess untuk tiap-tiap PC nya:
- klik PC0 pilih tab desktop lalu IP Configuration dan atur seperti ini :
- klik PC1 pilih tab desktop lalu IP Configuration dan atur seperti ini :
4. klik PC2 pilih tab desktop lalu IP Configuration dan atur seperti ini :
- klik PC3 pilih tab desktop lalu IP Configuration dan atur seperti ini :
5. - klik PC4 pilih tab desktop lalu IP Configuration dan atur seperti ini :
- klik PC5 pilih tab desktop lalu IP Configuration dan atur seperti ini :
6. - klik PC6 pilih tab desktop lalu IP Configuration dan atur seperti ini :
- klik PC7 pilih tab desktop lalu IP Configuration dan atur seperti ini :
7. - klik PC8 pilih tab desktop lalu IP Configuration dan atur seperti ini :
3. Buat koneksinya, antara PC dengan SWITCH (gunakan yang generic) gunakan KABEL
STRAIGHT , kemudian antara SWITCH dengan ROUTER (gunakan yang generic) juga
gunakan KABEL STRAIGHT, lalu antara ROUTER dengan ROUTER gunakan
KABEL SERIAL ( DTE ).
Perhatikan interface yang dipakai ketika menghubungkan antara switch dengan router,
disini untuk koneksi switch-router saya menggunakan interface fastethernet 0/0 pada
routernya dan serial 2/0 untuk koneksi router 0 – router 1 dan koneksi router 1 – router 2,
serial 3/0 untuk koneksi router 1 – router 0 dan router 2 – router 1
8. 4.Pada Router 0 atur ip address dan subnetmask untuk interface fastethernet 0/0 dan
mengatur ip address dan subnetmask untuk interface serial 2/0 serta mengatur ip route
dengan cara klik Router 0 pilih tab CLI lalu ketik seperti ini :
INCLUDEPICTURE "http://secercahcoretan.files.wordpress.com/2012/10/42.png?
w=529"
5.Pada Router 1 atur ip address dan subnetmask untuk interface fastethernet 0/0 dan
mengatur ip address dan subnetmask untuk interface serial 2/0 dan interface serial 3/0
serta mengatur ip route dengan cara klik Router 1 pilih tab CLI lalu ketik seperti ini :
9. 6. Pada Router 2 atur ip address dan subnetmask untuk interface fastethernet 0/0 dan
mengatur ip address dan subnetmask untuk interface serial 3/0 serta mengatur ip route
dengan cara klik Router 1 pilih tab CLI lalu ketik seperti ini :
10. 6. Sekarang kita coba ping dari PC0 ke PC3, PC6, klik PC 0 lalu pilih tab desktop terus pilih
comand prompt :
11. 7. Sekarang kita coba ping dari PC3 ke PC0, dan PC6 klik PC 3 lalu pilih tab desktop terus
pilih comand prompt :
8. Sekarang kita coba ping dari PC6 ke PC0, dan PC3 klik PC 6 lalu pilih tab desktop terus
pilih comand prompt :
Dari hasil di atas menunjukan reply sehingga routing sudah dikatakan berhasil.
12. SCRIPT UNTUK MENGATUR ROUTER
Router>en
Router#config
Configuring from terminal,
memory, or network [terminal]?
Enter configuration commands, one
per line. End with CNTL/Z.
Router(config)#interface
fastethernet 0/0
Router(config-if)#ip address 1.5.0.1
255.255.0.0
Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface
FastEthernet0/0, changed state to
up
%LINEPROTO-5-UPDOWN: Line
protocol on Interface
FastEthernet0/0, changed state to
up
Router(config-if)#exit
Router(config)#interface serial 2/0
Router(config-if)#ip address
2.10.0.1 255.255.0.0
Router(config-if)#clock rate 64000
This command applies only to DCE
interfaces
Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface
Serial2/0, changed state to down
Router(config-if)#exit
Router(config)#ip route 2.5.0.0
255.255.0.0 2.10.0.2
Router(config)#ip route 3.5.0.0
255.255.0.0 2.10.0.2
Router(config)#ip route 3.5.0.0
255.255.0.0 20.10.0.2
Router>en
Router#config
Configuring from terminal, memory,
or network [terminal]?
Enter configuration commands, one
per line. End with CNTL/Z.
Router(config)#interface fastethernet
0/0
Router(config-if)#ip address 2.5.0.1
255.255.0.0
Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface
FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line
protocol on Interface
FastEthernet0/0, changed state to up
Router(config-if)#exit
Router(config)#interface serial 3/0
Router(config-if)#ip address 2.10.0.2
255.255.0.0
Router(config-if)#clock rate 64000
This command applies only to DCE
interfaces
Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface
Serial3/0, changed state to down
Router(config-if)#exit
Router(config)#interface serial 2/0
Router(config-if)#ip address
20.10.0.1 255.255.0.0
Router(config-if)#clock rate 64000
This command applies only to DCE
interfaces
Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface
Serial2/0, changed state to down
Router(config-if)#exit
Router(config)#ip route 1.5.0.0
255.255.0.0 2.10.0.1
Router(config)#ip route 3.5.0.0
255.255.0.0 20.10.0.2
Router>en
Router#config
Configuring from terminal, memory, or
network [terminal]?
Enter configuration commands, one per line.
End with CNTL/Z.
Router(config)#interface fastethernet 0/0
Router(config-if)#ip address 3.5.0.1
255.255.0.0
Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface
FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol
on Interface FastEthernet0/0, changed state to
up
Router(config-if)#exit
Router(config)#interface serial 3/0
Router(config-if)#ip address 20.10.0.2
255.255.0.0
Router(config-if)#clock rate 64000
Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial3/0,
changed state to up
%LINEPROTO-5-UPDOWN: Line protocol
on Interface Serial3/0, changed state to up
Router(config-if)#exit
Router(config)#ip route 2.5.0.0 255.255.0.0
20.10.0.1
Router(config)#ip route 1.5.0.0 255.255.0.0
20.10.0.1
Router(config)#ip route 1.5.0.0 255.255.0.0
2.10.0.1% Invalid input detected at '^' marker.
Keterangan warna script:
Untuk mengatur ip address & netmask untuk interface fastEthernet 0/0
Untuk mengatur ip address & netmask untuk interface serial 2/0