The document describes Morley-IAS active and passive repeaters that connect to fire alarm control panels via an RS485 peripheral bus. The active repeater includes control buttons for system reset, muting alarms, and initiating a self-test, while the passive repeater only includes status indicators. Both repeaters display the control panel status using an LCD screen and LEDs. A maximum of 31 active repeaters can connect to the control panel, which supervises the connections. The repeaters require an external 24Vdc power supply.
The CF3000PRG passive repeater panel has a 2 x 40 backlit LCD display and 6 supervisory LEDs. It can be programmed to display information from a connected control panel, including fire alarms. It provides limited control functions like silencing alarms. With up to 20 repeaters connected, it offers a cost-effective way to display system status at multiple locations with minimal wiring and no required programming.
The ULCF3000PR passive repeater panel is a cost effective repeater that displays system information from an connected fire alarm control panel. It has a 2x40 LCD display and 6 LED indicators. When connected to a control panel loop, it can display the panel's text and indicate fires up to 2km away. It requires programming with local test information. The passive repeater connects to either a fire panel loop or network and provides monitoring of alarm states at a remote location through its display and indicators.
The document is a user manual for the PS 260 dual channel audio interface. It describes the product's general features, including two separate audio interfaces that allow connection between an ASL partyline intercom system and external 4-wire audio equipment. The user manual provides details on installation, front panel controls, rear panel connections, and setup instructions.
The FCM-1(A) Control Module and FRM-1(A) Relay Module are intelligent/addressable devices that can be used with Notifier fire alarm control panels. The FCM-1(A) provides a circuit to activate notification appliances like horns and strobes. The FRM-1(A) provides a dry contact output to activate auxiliary devices. Both modules use FlashScan communication and have an LED to indicate communication and activation status. They can be programmed to activate specific zones and areas.
The MIU872 is a single zone micro interface unit that can connect up to 20 conventional fire detectors to an intelligent fire alarm panel. It has built-in short circuit isolation and monitors the input zone for open and short circuit faults. Installation is quick and simple as it requires no addressing and can use existing wiring.
The document describes the R6000 range of intelligent addressable rack mounted control panels from Cooper Lighting and Safety. The R6000 consists of modular plug-in components that can be configured for functions like fire detection, alarm signaling, and plant control. The system supports up to 126 panels, 504 loops, and 64,512 addressable points. The floor rack unit houses the R6000 control panels and is constructed of mild steel.
This document provides information about the Qubino Flush 1D relay Z-Wave module. The module is used for switching electrical devices on or off and can be controlled via Z-wave network or a wall switch. It is designed to fit inside a flush mounting box and can support connection of a digital temperature sensor. The module also functions as a Z-Wave repeater to improve network range and stability. Installation and configuration details are included along with technical specifications.
The CF3000PRG passive repeater panel has a 2 x 40 backlit LCD display and 6 supervisory LEDs. It can be programmed to display information from a connected control panel, including fire alarms. It provides limited control functions like silencing alarms. With up to 20 repeaters connected, it offers a cost-effective way to display system status at multiple locations with minimal wiring and no required programming.
The ULCF3000PR passive repeater panel is a cost effective repeater that displays system information from an connected fire alarm control panel. It has a 2x40 LCD display and 6 LED indicators. When connected to a control panel loop, it can display the panel's text and indicate fires up to 2km away. It requires programming with local test information. The passive repeater connects to either a fire panel loop or network and provides monitoring of alarm states at a remote location through its display and indicators.
The document is a user manual for the PS 260 dual channel audio interface. It describes the product's general features, including two separate audio interfaces that allow connection between an ASL partyline intercom system and external 4-wire audio equipment. The user manual provides details on installation, front panel controls, rear panel connections, and setup instructions.
The FCM-1(A) Control Module and FRM-1(A) Relay Module are intelligent/addressable devices that can be used with Notifier fire alarm control panels. The FCM-1(A) provides a circuit to activate notification appliances like horns and strobes. The FRM-1(A) provides a dry contact output to activate auxiliary devices. Both modules use FlashScan communication and have an LED to indicate communication and activation status. They can be programmed to activate specific zones and areas.
The MIU872 is a single zone micro interface unit that can connect up to 20 conventional fire detectors to an intelligent fire alarm panel. It has built-in short circuit isolation and monitors the input zone for open and short circuit faults. Installation is quick and simple as it requires no addressing and can use existing wiring.
The document describes the R6000 range of intelligent addressable rack mounted control panels from Cooper Lighting and Safety. The R6000 consists of modular plug-in components that can be configured for functions like fire detection, alarm signaling, and plant control. The system supports up to 126 panels, 504 loops, and 64,512 addressable points. The floor rack unit houses the R6000 control panels and is constructed of mild steel.
This document provides information about the Qubino Flush 1D relay Z-Wave module. The module is used for switching electrical devices on or off and can be controlled via Z-wave network or a wall switch. It is designed to fit inside a flush mounting box and can support connection of a digital temperature sensor. The module also functions as a Z-Wave repeater to improve network range and stability. Installation and configuration details are included along with technical specifications.
In-wall dimmer module Z-Wave Plus Smart Home Europe manual englishDomotica daVinci
The document summarizes an in-wall dimmer module that is Z-Wave enabled and can control lighting and appliance loads. It describes how to include the module in a Z-Wave network, configure its settings, and troubleshoot issues. The module supports dimming light bulbs and controlling loads between 6W-300W. It transmits wirelessly within a 30 meter range and has overload protection.
The document describes the design and components of a remote-controlled spy robot. It has two main sections: 1) the remote control section, which uses an HT12E encoder and HT12D decoder to control the robot via radio signals from a wireless remote controller. 2) The video transmission section uses a wireless CCD camera powered by a 12V battery to capture video that is transmitted to a remote receiver via radio signals. The robot can be controlled remotely to move forward, backward, left, or right using two 12V gear motors and an L293D motor driver circuit.
The document provides instructions for setting up and using a Z-Wave wall controller device. It can be used to control other Z-Wave devices or activate scenes. Pushing all four buttons for five seconds puts the device in management mode for configuration. The device supports secure communication and runs on a single CR2032 battery. It has different operating modes for direct control or scene activation of associated Z-Wave devices.
The document provides information on a Qubino Flush RGBW Dimmer module that can control RGB/RGBW LED strips, bulbs, and other devices. It has 4 input terminals that can be configured for LED control or 100KΩ signal readouts. It supports inclusion in a Z-Wave network and configuration via parameters to set functions like input switch type, color mode, and auto scene settings. Installation and connection details are also included.
This document provides information about a Z-Wave DIN dimmer module used for dimming lights and fans. The module can be controlled through a Z-Wave network or wall switch. It measures power consumption and supports connecting a temperature sensor. The module is small, designed to mount on a DIN rail, and can act as a repeater to improve the Z-Wave network range. Technical specifications, diagrams, instructions and configuration parameters are provided.
This document provides information about a vehicle's chime warning system, including:
- The system warns the driver if the seat belt is not fastened, temperatures are high, lights are on with the ignition off and door open, or the key is in the ignition with the door open.
- It describes the major components of the system: the driver door jamb switch, driver seat belt switch, headlamp switch, instrument cluster, and key-in ignition switch.
- Diagnosis and testing procedures are provided for each component to determine if it is functioning properly.
Qubino flush dimmer 0 10-v plus user manual_v1.0_engDomotica daVinci
The document describes the Qubino Flush Dimmer 0-10V, a Z-Wave compatible dimmer module with a 0-10V output and multi-function input. It can be controlled via push button, potentiometer, or 0-10V signal. The module includes to a Z-Wave network and supports association groups to control other devices. It has configuration parameters to set functions like input type, auto on/off times, minimum/maximum dimming levels, and sensor reporting thresholds.
The document describes Soundcraft's EPM and MPM multi-purpose mixer lines. The EPM mixers come in 6, 8, and 12 channel models and feature professional microphone preamps, phantom power, and inserts. They are configured for desktop or rack use. The MPM mixers are suitable for live sound and come in 12 and 20 channel models, including stereo inputs, aux sends, and a 2-track input/output. Both mixer lines provide quality audio and value for a range of applications.
The document summarizes a Plena Voice Alarm Call Station from Bosch Communications Systems. The call station allows selection of up to six zones to make calls to in a public address system built with the Plena Voice Alarm System. It has selectable gain, speech filtering, and output limiting for improved intelligibility. Status LEDs and a rotary control provide feedback and adjustments.
This document provides specifications for the Balboa VS523DZ spa system. It includes the model number, software version, and component part numbers. The document also lists the basic system features, including power requirements, output devices, and optional equipment. Wiring diagrams and DIP switch settings are provided for two different output device configurations.
The document summarizes the EdgeReader ERP40, an IP access solution that combines an access controller and host interface in a single unit with an integrated multiCLASS contactless smart card reader. It provides network access over CAT-5 cable and Power over Ethernet, eliminating the need for separate power supplies. It stores up to 44,000 cards onsite with a built-in TCP/IP interface and supports various card technologies. Key features include network connectivity, onboard processing and storage, input/output options and support for access control functions.
This in-wall remote module is a Z-Wave transceiver that can be installed in a wall box. It allows connection of traditional wall switches or sensors to create a wireless Z-Wave network. The module has a link button and LED for inclusion, exclusion, reset, and association with other Z-Wave devices. It supports basic functions like on/off switching through the Z-Wave protocol.
This document is a user manual for the PS 155 wireless interface. It provides instructions on unpacking, installing, and operating the interface. The interface connects a wired partyline intercom system to a wireless intercom system. It splits and combines the audio signals, and includes volume controls and options to switch between receive and transmit modes, including push to talk, call, and voice activation. The manual describes the front panel controls, rear panel connections, operation modes, and technical specifications.
The document provides instructions for installing and operating a Universal Relay Switch made by WiDom. It includes:
1) Details on the device components and connections for both 3-wire and 2-wire installations. Wiring diagrams are provided for AC and DC loads.
2) Information on including and excluding the device from a Z-Wave network, as well as resetting it to factory settings.
3) Descriptions of how to configure the device's behavior based on the number of clicks or hold time on an external switch, including options to control associated devices.
The CF3000PRG passive repeater panel displays system information from an intelligent addressable fire system. It has a backlit LCD display and LED indicators. It can be programmed to be fully passive for display only or semi-passive for limited control functions like silencing alarms. When connected to a loop or network, it will show the status of the host panel and any other panels that activate. Up to 20 repeaters can be connected to a single loop or network to provide status information across the system.
The ZXSe Range Data Sheet summarizes an analogue addressable fire alarm control panel system. It supports five detection protocols and can be expanded with additional devices, loop cards, printers, or networked panels. Key features include multi-protocol support, modular expandability, intuitive user interface, and networking of up to 99 panels to manage over 60,000 devices.
The LBB 4433/00 Call Station Kit allows for custom call stations with 16 keypads. It has a built-in speech filter and limiter for clear audio, supports redundant networking, and can make emergency calls even if the network controller fails. The kit includes connectors and can be extended with numeric keypads.
7SR220 series relays include for directional control of the overcurrent and earth fault functionality and are typically installed where fault current can flow in either direction i.e. on interconnected systems. Relays have five current and four voltage inputs they are housed in E6 or E8 cases.
YSI 5500D 5400 and 5200A aquaculture monitors and controllersXylem Inc.
Continuously monitor water quality in any aquaculture system with the YSI monitoring and control instruments.
Whether it is the need for a multiparameter solution or single measurement at one location, the YSI monitors are ideal.
The document provides instructions for operating an infrared hydrocarbon gas detector. It can be used as a standalone detector or as part of a larger safety system. It continuously monitors combustible gases from 0-100% LEL and has configurations that output analog signals or provide alarm relays. It operates by measuring the absorption of infrared light by hydrocarbon gases in its measurement chamber.
The PRS-NCO-B Network Controller is a digital public address and emergency sound system control unit that routes up to 28 simultaneous audio channels, delivers power to the system, reports faults, and controls the system. It has four audio inputs and four audio outputs, controls and routes 28 audio channels, and has eight control inputs and five control outputs. It can be configured via Ethernet and stores the last 200 fault events.
In-wall dimmer module Z-Wave Plus Smart Home Europe manual englishDomotica daVinci
The document summarizes an in-wall dimmer module that is Z-Wave enabled and can control lighting and appliance loads. It describes how to include the module in a Z-Wave network, configure its settings, and troubleshoot issues. The module supports dimming light bulbs and controlling loads between 6W-300W. It transmits wirelessly within a 30 meter range and has overload protection.
The document describes the design and components of a remote-controlled spy robot. It has two main sections: 1) the remote control section, which uses an HT12E encoder and HT12D decoder to control the robot via radio signals from a wireless remote controller. 2) The video transmission section uses a wireless CCD camera powered by a 12V battery to capture video that is transmitted to a remote receiver via radio signals. The robot can be controlled remotely to move forward, backward, left, or right using two 12V gear motors and an L293D motor driver circuit.
The document provides instructions for setting up and using a Z-Wave wall controller device. It can be used to control other Z-Wave devices or activate scenes. Pushing all four buttons for five seconds puts the device in management mode for configuration. The device supports secure communication and runs on a single CR2032 battery. It has different operating modes for direct control or scene activation of associated Z-Wave devices.
The document provides information on a Qubino Flush RGBW Dimmer module that can control RGB/RGBW LED strips, bulbs, and other devices. It has 4 input terminals that can be configured for LED control or 100KΩ signal readouts. It supports inclusion in a Z-Wave network and configuration via parameters to set functions like input switch type, color mode, and auto scene settings. Installation and connection details are also included.
This document provides information about a Z-Wave DIN dimmer module used for dimming lights and fans. The module can be controlled through a Z-Wave network or wall switch. It measures power consumption and supports connecting a temperature sensor. The module is small, designed to mount on a DIN rail, and can act as a repeater to improve the Z-Wave network range. Technical specifications, diagrams, instructions and configuration parameters are provided.
This document provides information about a vehicle's chime warning system, including:
- The system warns the driver if the seat belt is not fastened, temperatures are high, lights are on with the ignition off and door open, or the key is in the ignition with the door open.
- It describes the major components of the system: the driver door jamb switch, driver seat belt switch, headlamp switch, instrument cluster, and key-in ignition switch.
- Diagnosis and testing procedures are provided for each component to determine if it is functioning properly.
Qubino flush dimmer 0 10-v plus user manual_v1.0_engDomotica daVinci
The document describes the Qubino Flush Dimmer 0-10V, a Z-Wave compatible dimmer module with a 0-10V output and multi-function input. It can be controlled via push button, potentiometer, or 0-10V signal. The module includes to a Z-Wave network and supports association groups to control other devices. It has configuration parameters to set functions like input type, auto on/off times, minimum/maximum dimming levels, and sensor reporting thresholds.
The document describes Soundcraft's EPM and MPM multi-purpose mixer lines. The EPM mixers come in 6, 8, and 12 channel models and feature professional microphone preamps, phantom power, and inserts. They are configured for desktop or rack use. The MPM mixers are suitable for live sound and come in 12 and 20 channel models, including stereo inputs, aux sends, and a 2-track input/output. Both mixer lines provide quality audio and value for a range of applications.
The document summarizes a Plena Voice Alarm Call Station from Bosch Communications Systems. The call station allows selection of up to six zones to make calls to in a public address system built with the Plena Voice Alarm System. It has selectable gain, speech filtering, and output limiting for improved intelligibility. Status LEDs and a rotary control provide feedback and adjustments.
This document provides specifications for the Balboa VS523DZ spa system. It includes the model number, software version, and component part numbers. The document also lists the basic system features, including power requirements, output devices, and optional equipment. Wiring diagrams and DIP switch settings are provided for two different output device configurations.
The document summarizes the EdgeReader ERP40, an IP access solution that combines an access controller and host interface in a single unit with an integrated multiCLASS contactless smart card reader. It provides network access over CAT-5 cable and Power over Ethernet, eliminating the need for separate power supplies. It stores up to 44,000 cards onsite with a built-in TCP/IP interface and supports various card technologies. Key features include network connectivity, onboard processing and storage, input/output options and support for access control functions.
This in-wall remote module is a Z-Wave transceiver that can be installed in a wall box. It allows connection of traditional wall switches or sensors to create a wireless Z-Wave network. The module has a link button and LED for inclusion, exclusion, reset, and association with other Z-Wave devices. It supports basic functions like on/off switching through the Z-Wave protocol.
This document is a user manual for the PS 155 wireless interface. It provides instructions on unpacking, installing, and operating the interface. The interface connects a wired partyline intercom system to a wireless intercom system. It splits and combines the audio signals, and includes volume controls and options to switch between receive and transmit modes, including push to talk, call, and voice activation. The manual describes the front panel controls, rear panel connections, operation modes, and technical specifications.
The document provides instructions for installing and operating a Universal Relay Switch made by WiDom. It includes:
1) Details on the device components and connections for both 3-wire and 2-wire installations. Wiring diagrams are provided for AC and DC loads.
2) Information on including and excluding the device from a Z-Wave network, as well as resetting it to factory settings.
3) Descriptions of how to configure the device's behavior based on the number of clicks or hold time on an external switch, including options to control associated devices.
The CF3000PRG passive repeater panel displays system information from an intelligent addressable fire system. It has a backlit LCD display and LED indicators. It can be programmed to be fully passive for display only or semi-passive for limited control functions like silencing alarms. When connected to a loop or network, it will show the status of the host panel and any other panels that activate. Up to 20 repeaters can be connected to a single loop or network to provide status information across the system.
The ZXSe Range Data Sheet summarizes an analogue addressable fire alarm control panel system. It supports five detection protocols and can be expanded with additional devices, loop cards, printers, or networked panels. Key features include multi-protocol support, modular expandability, intuitive user interface, and networking of up to 99 panels to manage over 60,000 devices.
The LBB 4433/00 Call Station Kit allows for custom call stations with 16 keypads. It has a built-in speech filter and limiter for clear audio, supports redundant networking, and can make emergency calls even if the network controller fails. The kit includes connectors and can be extended with numeric keypads.
7SR220 series relays include for directional control of the overcurrent and earth fault functionality and are typically installed where fault current can flow in either direction i.e. on interconnected systems. Relays have five current and four voltage inputs they are housed in E6 or E8 cases.
YSI 5500D 5400 and 5200A aquaculture monitors and controllersXylem Inc.
Continuously monitor water quality in any aquaculture system with the YSI monitoring and control instruments.
Whether it is the need for a multiparameter solution or single measurement at one location, the YSI monitors are ideal.
The document provides instructions for operating an infrared hydrocarbon gas detector. It can be used as a standalone detector or as part of a larger safety system. It continuously monitors combustible gases from 0-100% LEL and has configurations that output analog signals or provide alarm relays. It operates by measuring the absorption of infrared light by hydrocarbon gases in its measurement chamber.
The PRS-NCO-B Network Controller is a digital public address and emergency sound system control unit that routes up to 28 simultaneous audio channels, delivers power to the system, reports faults, and controls the system. It has four audio inputs and four audio outputs, controls and routes 28 audio channels, and has eight control inputs and five control outputs. It can be configured via Ethernet and stores the last 200 fault events.
The IntelliKnight 5808 is a single loop, addressable fire alarm control panel that provides 127 detection points and integrated communication capabilities. It performs self-diagnostics on connected sensors and includes features like drift compensation. The basic panel can be expanded with additional modules. Notifications are powered by the onboard 6A power supply or an optional expansion module.
The Plena Loop Amplifier is designed to drive an induction loop installed in floors or ceilings, covering up to 600 square meters. It has two microphone/line inputs, a priority input, and controls for tone, limiting, and automatic gain. The amplifier integrates into EN 54-16 and EN 60849 compliant emergency systems and provides supervision of key functions.
The document summarizes the Cooper CF1000VDS range of intelligent addressable fire alarm control panels. Key points:
- The CF1000VDS range includes 1-loop and 2-loop control panels approved to EN54 standards.
- The panels offer up to 200 addresses per loop, network capability up to 126 panels, and features like soft addressing and a touchscreen user interface.
- Benefits include simple operation, flexible network and programming capabilities, and compatibility with a range of accessories.
This document provides a summary of an audio amplifier's key features:
1. It has advanced DSP processing including IIR and FIR filters as well as high quality converters for smooth sound.
2. It has versatile connectivity including analog, digital, and network ports and a user interface for easy setup and control.
3. It is designed for reliability and high power output with features like efficient cooling, high voltage output, and overload protection.
7SR224 series relays include for directional control of three phase overcurrent and earth fault functionality and typically installed as an integral controller for a pole mounted recloser. The controller offers an integrated auto-reclose solution for use on OHL feeders.
The relay functionality allows highly flexible settings for current and time grading making it compatible with all types of overcurrent protections.
The document is a presentation about power management fundamentals from Analog Devices. It discusses different types of power conversion and regulation products like linear voltage regulators and switching regulators. It explains the need for stable, clean power supplies to avoid noise and errors in high-precision systems. Key topics covered include linear regulators, switching regulators, power distribution, minimizing noise and ripple, and tips for successful power design. The presentation is part of Analog Devices' 2011 webcast series on signal processing fundamentals.
The GRAFIK Eye 3000 Series control unit provides preset dimming controls for lighting. It allows setup and recall of four preset lighting scenes plus off using buttons. It can directly control many light sources or control others through power interfaces. Models are available to accept different input voltages and control two to six zones of lighting.
The SIPROTEC 7SA522 relay provides full-scheme distance protection for transmission lines with various protection functions:
- Distance protection with 6 measuring systems using mho and quadrilateral characteristics for phase and ground faults.
- Additional functions include overcurrent, power swing, under/over voltage, auto-reclosing, breaker failure protection.
- It has communication interfaces for protection data exchange and integration into a control system via protocols like IEC 60870-5-103, PROFIBUS, DNP 3.0, Ethernet.
- The relay is suitable for cables and overhead lines with features like high-speed tripping, self-setting power swing detection, and adaptive auto-rec
The Plena Voice Alarm Controller is the central controller for the Plena Voice Alarm System. It has built-in amplification and supports up to six zones, with additional routers allowing expansion to 60 zones. It stores and plays emergency messages, provides background music, and interfaces with call stations. The controller complies with EN 60849 and EN 54-16 standards for voice alarm systems.
The document describes a conventional fire alarm panel that includes:
- Microprocessor control and SMT electronics compliant with various standards
- Detection of up to 25 fire detectors and call points on one zone
- Two output control points to control indicators like sounders and strobes
- Standby batteries, fault and alarm indicators, and short circuit detection
- Simple installation and operation via a key switch
The document describes the Siemens 7SR10 numerical overcurrent relay. It is a member of Siemens' Argus product family and provides protection, monitoring, instrumentation and metering functions. It has a non-directional overcurrent element and additional voltage inputs to provide directional protection. It has communication ports, a front display, and push buttons for control and monitoring. It also provides several other protection functions including directional power, thermal overload protection, and earth fault protection.
The PRS-CSR is a remote call station that connects to a Praesideo network via CAT-5 cable up to 1 km long. It uses standard Praesideo keypads and interfaces with the network through a PRS-CSI unit. The remote call station provides the same functionality as a basic call station and can be powered via CAT-5 cable or a local power supply.
The VertX V100 Door/Reader Interface connects two access control card readers and controls one or two doors. It features on-board flash memory for program updates, connects to the V1000 host controller via RS-485, and the V1000 communicates with the host system via TCP/IP. The V100 processes access control decisions locally and reports all activity to the V1000.
The document summarizes the specifications and features of the Texecom Odyssey 3 external sounder and strobe series. Key features include a 115dB volume, IP65 sealed electronics, selectable SAB/SCB mode, screw, lid, and wall tamper protection, twin alternating LEDs, and revolutionary screw retention system. It is competitively priced, easy to install, and provides uncompromising performance for professional security installations.
The document describes the TOA VM-3000 series integrated voice evacuation system. It is an EN 54 compliant system that combines emergency voice alarm and public address functions. Key features include fully digital audio processing and control, built-in voice messages, monitoring of speaker lines, and support for paging, background music, and microphone inputs. The system is suitable for small to medium venues and provides emergency evacuation and general announcement capabilities.
The document describes the TOA VM-3000 series integrated voice evacuation system. The VM-3000 series provides both emergency evacuation functions and general public address/paging functions. It is EN 54 certified and ideal for small to medium venues. The system has integrated amplifiers, supports up to 60 speaker zones, and can be configured via software.
This document provides installation instructions for installing a SV-200MA Surveillance Board in VM-2120 or VM-2240 amplifiers. The SV-200MA adds monitoring, zone control, and backup amplifier functions. It consists of an SV-200M board and SV extension board. The 10 step installation process includes setting jumpers, connecting cables between the boards, mounting the surveillance board, and replacing the amplifier cover.
The document describes TOA's SC Series Paging Horn Speakers. It includes specifications for 6 models that are rated at either 10W, 15W, or 30W and are designed for both indoor and outdoor use. The speakers feature weatherproof stainless steel brackets, powder coated horns, and input impedance selector switches on high-impedance models. Diagrams show the speakers' frequency responses, beamwidths, directivity factors, and polar responses.
The document describes TOA's SC Series Paging Horn Speakers. It includes specifications for 6 models that are rated at either 10W, 15W, or 30W and are designed for both indoor and outdoor use. The speakers feature weatherproof stainless steel brackets, powder coated horns, and input impedance selector switches on high-impedance models. Diagrams show the speakers' frequency responses, beamwidths, directivity factors, and polar responses.
The document describes TOA's CS-154 and CS-304 outdoor wide-range speakers. The speakers use wide-range horns to provide high quality background music or paging announcements over a wide area. They are designed for outdoor use and have weatherproof enclosures that can withstand demanding environmental conditions. The speakers have adjustable impedance settings and provide high output with increased efficiency through the use of a horn and cone speaker combination.
The document describes the TOA BS-678 wall mount speaker system. It is a double-cone speaker with a wooden cabinet and stylish, compact design. It produces high quality sound for background music and announcements. Key features include an adjustable input impedance selector, push-in connector for easy wiring, and horizontal or vertical mounting orientation. Specifications include a frequency response of 150-20,000Hz, 6W or 3W power handling, and an off-white finish.
The document describes the TOA BS-633A/633AT wall mount speaker systems. The BS-633A is a basic 5" cone speaker with a transformer allowing multiple power taps. The BS-633AT includes an additional built-in attenuator, allowing connection to 2-wire and 3-wire speaker systems. Both have a compact ABS resin enclosure and push-in terminal for easy installation. Key specifications include a frequency response of 120-15,000Hz, 91dB sensitivity, and multiple power taps for 100V and 70V speaker lines.
This document summarizes an LB1-UW06-Fx cabinet loudspeaker from Bosch. It is a 6W loudspeaker intended for indoor use. It has mounting brackets for wall or ceiling mounting. It is constructed of MDF and has a durable vinyl or cloth covering available in white or black. It provides good speech intelligibility and background music reproduction.
This document summarizes a 6W loudspeaker for indoor use. It has good speech intelligibility and background music reproduction. The loudspeaker has an MDF construction with mounting brackets for wall or ceiling installation. It complies with international safety regulations and certifications.
The LA1-UW36-x is a 36W column loudspeaker for indoor use where directivity is important. It has high sensitivity and provides good speech intelligibility and background music reproduction. It has a swivel wall mounting bracket and is available in black or white. It uses four dual cone drivers and a durable MDF enclosure for reliability under extreme conditions.
The LA1-UW24-x is a 24W column loudspeaker for indoor use where directivity is important. It has good speech intelligibility and background music reproduction. It comes with a swivel wall-mounting bracket and is available in black or white. It has four high-sensitivity drivers and can be powered at full, half, or quarter power via a terminal block on the rear.
This document provides specifications for a BGT 4139TS video camera model. It includes details on the camera's image sensor, resolution, lenses, operational features like auto day/night mode and infrared LEDs, environmental tolerances, electrical requirements, mechanics including dimensions and weight, and manufacturer. The camera has a 1/3" CCD sensor, 600TVL resolution, auto settings, infrared for night vision up to 20 meters, and an IP66-rated casing.
This document provides specifications for a BGT 5504A camera model, including details about its video capabilities, lens, operational features, environmental tolerances, electrical requirements, and dimensions. It has a 1/4" CCD image sensor, 420TVL resolution, auto day/night mode, 15m infrared range, and measures 92mm diameter by 80mm, weighing 190g.
This data sheet provides specifications for the BGT 5140A video camera, including its CCD image sensor, PAL/NTSC compatibility, effective pixel count, 420TVL horizontal resolution, low light performance down to 0.5 lux, auto day/night functionality, 3.6mm fixed focal length lens, operating temperature range of -10°C to 50°C, power requirements of 12V 150mA with a 12V 1A adapter, and compact dimensions of 60x90x190g.
This data sheet provides specifications for a BGT 9120TS security camera model. It lists technical details such as the CCD image sensor and effective pixel resolution, as well as operational features including auto day/night mode, backlight compensation, and automatic gain control. Environmental specifications note an operating temperature range of -10°C to 50°C and IP66 protection rating. The camera is powered by a 12V 370mA power supply and has dimensions of 266x97x63mm.
This data sheet provides specifications for a BGT 9119AS video camera model. It has a 1/3 inch Sony CCD image sensor that can capture video in PAL or NTSC formats with effective pixel counts of 752x582 or 768x494 respectively. The camera has a 3.6/6mm fixed lens, auto day/night functionality, and can function in temperatures from -10 to 50 degrees Celsius. It is powered by a 12V 1A adapter and has IP67 protection against dust and water.
This document provides specifications for the BGT 720TOS security camera model, including details about its video capabilities, lens, operational features, environmental tolerances, electrical requirements, and dimensions. Key specs include a 1/3" Sony CCD image sensor, 600TVL horizontal resolution, auto day/night functionality, auto electronic shutter speed range of 1/50-1/100,000 sec for PAL and 1/60-1/100,000 sec for NTSC, operating temperature range of -10°C to +50°C, input voltage of DC12V/150mA, and compact dimensions of 102*55*40mm.
This document provides specifications for the BGT 5221AS video camera model. It includes details about the camera's image sensor, resolution, lenses, video output, day/night functionality, electrical requirements, and dimensions. Key features noted are a 1/3" Sony CCD image sensor, 480TVL horizontal resolution, auto day/night mode, infrared LEDs for night vision up to 10 meters, and DC12V 400mA power input. The camera measures 90*108*108mm and weighs 300g.
2. Mechanical Electrical
Weight: 1.7Kg (approx) Operating voltage
Operating Temperature: +5ºC to +45ºC 18 to 32 Vdc
Maximum Humidity: 10% to 93% non-condensing Operating Current
90mA (Quiescent) 120m (Alarm)
Terminals
Maximum cross section 2.5mm2
LED indicators
Fire, Fault, Disables, Accepted, Silenced, Power,
Communications, loss.
EXrA User Controls:
Keyswitch activated - System Reset, Sound Alarms,
Silence/Resound, Mute, Accept and Self Test
Part Numbers
709-601-001 ZXr-A Active Repeater.
709-601-101 ZXr-A Active Repeater UL listed
709-701-001 ZXr-P Passive Repeater.
709-701-101 ZXr-P Passive Repeater UL listed.
002-600-002 Repeater Bezel.
795-004-001 RS485 Communication Module.
Fire System Compatibility
Morley-IAS is fully committed to offering practical solutions and supporting products that enhance your buildings control systems.
Other Supporting Products Include
• Morley-IAS Intelligent Public Address and Voice Alarm Equipment
• Morley-IAS ZX range of networkable analogue addressable Fire Alarm Panels
• Morley-IAS Dimension Analogue Addressable Panels
• Morley-IAS Horizon Conventional Panels
• Morley-IAS Extinguishing Panels
For further details on these or any other Morley-IAS product please contact your local distribution point, Morley-IAS Regional Sales Manager or
via our contact details.
Morley-IAS by Honeywell a real choice for fire solutions, committed to supporting our device partners.
Charles Avenue T: +44 (0) 1444 23 55 56
Burgess Hill F: +44 (0) 1444 25 44 10
West Sussex E: sales@morleyias.co.uk
RH15 9UF UK www.morley-ias.co.uk