The document provides assembly instructions for a paper model of the Great Pyramid of Khufu in Egypt. It instructs the builder to number each section before cutting, and describes various fold types and where to apply glue. The pyramid was the largest of the Giza pyramids, standing over 137 meters tall, and its model includes 7 sections to be assembled according to the numbered instructions. Builders are advised to crease folds sharply and handle small parts with care.

1. Great Pyramid of Khufu, Egypt: Assembly Instructions Canon ® is a registered trademark of Canon Inc. © Canon Inc. © T.Ichiyama
Before starting assembly:Writing the number of each section on its back Indicates where sections should
side before cutting out the sections is highly recommended. be glued together.
(* This way, you can be sure which section is which even after cutting Indicates where to insert sections.
out the sections.) Do not glue the sections together.
http://www.canon.com/c-park/en/
Align these lines.
4
View of completed model
Great Pyramid of Khufu, Egypt Assembly Instructions
The Great Pyramid of Khufu is the largest of the roughly 60 pyramids found on the west bank of Glue
Mountain fold(dotted line)
the Nile. Composed of some 2.3 million stone blocks weighing 2.5 tons each, this pyramid The glue spot(colored dot)
Make a mountain fold.
shows where to apply the glue.
today measures 230 meters on each side at the base and 137 meters high. Until the construction
Valley fold(dashed and dotted line) Glue spot(Red dot)
of the Eiffel Tower, this was the world’ s tallest structure.
Make a valley fold. Glue parts with the same number together.
Scissors line(solid line) Glue spot(Green dot)
Cut along the line. Glue within the same part.
Cut in line(solid line) Glue spot(Blue dot)
*This model was designed for Papercraft and may differ from the original in some respects. Cut along the line. Glue to the rear of the other part.
Parts list(pattern):Four A4 sheets(No.3 to No.6)
No. of Parts:7 Tools and materials
Scissors, set square, glue(We recommend stick glue), pencil, used
ballpoint pen, toothpicks, tweezers, (useful for handling small parts)
*Build the model by carefully reading the Assembly Instructions, in the parts sheet page order.
Before gluing, crease the paper along mountain fold and valley
Assembly tip fold lines and make sure rounded sections are nice and stiff.
*Hint: Trace along the folds with a ruler
and an exhausted pen (no ink) to get a sharper, easier fold. Glue, scissors and other tools may be dangerous to young children
Caution so be sure to keep them out of the reach of young children.

2. Great Pyramid of Khufu, Egypt: Assembly Instructions Canon ® is a registered trademark of Canon Inc. © Canon Inc. © T.Ichiyama
Finished!

3. Great Pyramid of Khufu, Egypt: Pattern Canon ® is a registered trademark of Canon Inc. © Canon Inc. © T.Ichiyama
Great Pyramid of Khufu
Giza, Egypt

4. Great Pyramid of Khufu, Egypt: Pattern Canon ® is a registered trademark of Canon Inc. © Canon Inc. © T.Ichiyama
CAUTION Do not hit other people with the pointed edges. Doing so could result in injury. Adults should make sure that children observe this caution.
© T.Ichiyama Canon ® is a registered trademark of Canon Inc. http://www.canon.com/c-park/en/

5. Great Pyramid of Khufu, Egypt: Pattern Canon ® is a registered trademark of Canon Inc. © Canon Inc. © T.Ichiyama
Stress-relieving
chambers
Air duct
Pharaoh's Antechamber
Chamber
Grand
Gallery
Air duct
Air duct
Ascending
Air duct passage
Queen's Entrance
Chamber
Around 2550 B.C.
Ancient name: Horizon of Khufu
Height (when completed):
approximately 146 meters Auxiliary
Height (now): passage
approximately 137 meters
Width at base:
approximately 230 meters Subterranean Descending passage
Incline: approximately 52°
Estimated volume: Chamber
approximately 2,521,000 cubic meters

6. Great Pyramid of Khufu, Egypt: Pattern Canon ® is a registered trademark of Canon Inc. © Canon Inc. © T.Ichiyama