This document provides assembly instructions for a paper model of the Eiffel Tower with separate day and night models. The summary is: 1. Write the part numbers on the back of each section before cutting them out. Assemble the tower structure and base sections first before attaching the pillars. 2. Attach the parts in numbered order, aligning the printed symbols. Assemble so the structure is flush with the background. 3. Continue assembling the structure and attaching the sides. Fold and insert parts inside and attach to the bottom. 4. Assemble the base by drawing lines on the reverse of part 32 and attaching part 37 to align. Finally, glue the tower edges together

1. Eiffel Tower (Separate Night and Day Models; France): Assembly Instructions
Canon ® is a registered trademark of Canon Inc. © Canon Inc. © PAOPAO. Inc
Before starting assembly:Writing the number of each section on its back side
before cutting out the sections is highly recommended. Indicates where sections
(* This way, you can be sure which section is which even after cutting out should be glued together.
http://www.canon.com/c-park/en/ the sections.)
* In addition to the separate day and night models,
you can build an Eiffel Tower model with combined day and night backgrounds.
[1] Assemble the tower structure (the base below the pillars).
Attach the rear surface parts after first attaching the side surface parts into place.
View of completed model
*This model was designed for Papercraft and may differ from the original in some respects.
Assembly Instructions: Four A4 sheets (No.1 to No.4)
*Build the model by carefully reading the Assembly Instructions, in the parts sheet page order. Attach these pieces in
the same way as on
the opposite side.
*Hint: Trace along the folds with a ruler
and an exhausted pen (no ink) to get a sharper, easier fold.
Assembly Instructions
Glue
Mountain fold(dotted line)
Make a mountain fold. The glue spot(colored dot) Attach parts 4 and 6 into
shows where to apply the glue. place after first attaching
Valley fold(dashed and dotted line) Glue spot(Red dot) part 2.
Make a valley fold. Glue parts with the same number together.
Scissors line(solid line) Glue spot(Green dot)
Cut along the line. Glue within the same part.
Cut in line(solid line) Glue spot(Blue dot)
Cut along the line. Glue to the rear of the other part.
Attach parts 8 and 10 last.
Scissors, set square, glue(We recommend stick glue), pencil, used
Tools and materials ballpoint pen, toothpicks, tweezers, (useful for handling small parts)
Build the other structure in identical fashion.
Before gluing, crease the paper along mountain fold and valley
Assembly tip fold lines and make sure rounded sections are nice and stiff.
* Assemble the night parts in the same way.
Glue, scissors and other tools may be dangerous to young children Night part numbers are the same as for the day parts.
Caution so be sure to keep them out of the reach of young children.

2. Eiffel Tower (Separate Night and Day Models; France): Assembly Instructions
Canon ® is a registered trademark of Canon Inc. © Canon Inc. © PAOPAO. Inc
[2] Assemble the structure by putting the parts together in numbered order, aligning the printed symbols appearing on the parts.
* Assemble these parts so that the structure is flush with the background.
Attach part 16 into position on
the white area of part 15.
Attach part 15 into position along
the white line on part 14.
Attach part 14 into position along
the white line on top of part 13.
Attach the base, then fold
in the side flaps.
Attach the pillars into place
so that they align with the
white symbols printed on top
of part 14.
Attach the bottom
in the same way.
Left side Right side
Build the other structure in identical fashion.
* Assemble the night parts in the same way.
Night part numbers are the same as for the day parts.

3. Eiffel Tower (Separate Night and Day Models; France): Assembly Instructions
Canon ® is a registered trademark of Canon Inc. © Canon Inc. © PAOPAO. Inc
[3] Assemble the structure.
* Assemble these parts so that the structure is flush with the background.
Attach the sides in the same way.
Fold and insert inside
the structure, then attach
to the bottom part.
Attach to the bottom inside
assembled part 12.
Attach in the same way as the top.
Build the other structure in identical fashion.
* Assemble the night parts in the same way.
Night part numbers are the same as for the day parts.

4. Eiffel Tower (Separate Night and Day Models; France): Assembly Instructions
Canon ® is a registered trademark of Canon Inc. © Canon Inc. © PAOPAO. Inc
[4] Assemble the base.
Before attaching the parts, draw lines
crossing perpendicularly at the center
* Finally, glue the edges
on the reverse side of part 32.
of the towers
together. * After assembling the rear sides of the two
Eiffel Towers, attach them atop the base.
c
. In
AO
OP
PA
©
.
Inc
/ on
/en an
ark of C
/c-p ark
om dem
n.c tra
no red
.ca iste
ww reg
/w a
p:/ is
htt on ®
n
Ca
Eiffel Tower
Paris, France
Turn the base upside down and
attach part 37 to align with the lines
you drew in the previous step.
Inc
O.
O PA
PA
©
.
Inc
n/ anon
/e
ark of C
/c-p ark
o m de m
n.c tra
no red
.ca iste
ww reg
://w is a
ttp ®
h on
n
Ca
Eiffel Tower
Paris, France
Finished!
View from below
* Night part numbers are the same as for the day parts.