This document describes a new strategy for comprehensively analyzing polybrominated diphenyl ethers (PBDEs), polychlorinated dibenzo-p-dioxins (PCDDs), polychlorinated dibenzofurans (PCDFs), and polychlorinated biphenyls (PCBs) using gas chromatography coupled with mass spectrometry. The method allows for the purification and fractionation of the target compound groups in a simple multi-step automated clean-up. The compounds are then analyzed using a single benchtop mass spectrometer in four separate injections. Electron impact ionization followed by tandem mass spectrometry provides the required sensitivity for environmental levels while maintaining selectivity, accuracy, and repeatability.
The document describes a modification of an analytical method to allow for the determination of ultratrace levels of polybrominated diphenyl ethers (PBDEs), polybrominated dibenzo-p-dioxins and furans (PBDDs/Fs), and polychlorinated dibenzo-p-dioxins and furans (PCDDs/Fs) from a single combustion flue gas sample. The modifications addressed issues related to photolytic and thermal debromination of brominated compounds. This included optimization of extraction time and solvents, cleanup and fractionation steps, and high-resolution gas chromatography separation. The optimized method enabled quantification of 56 PBDE congeners, 15 PBDD/F
This document describes a method for analyzing ultratrace levels of polybrominated diphenyl ethers (PBDEs), polybrominated dibenzo-p-dioxins and furans (PBDDs/Fs), and polychlorinated dibenzo-p-dioxins and furans (PCDDs/Fs) from combustion flue gas samples. The method was optimized to address potential degradation issues for brominated compounds during extraction, cleanup, and analysis. Modifications included selecting solvents to minimize debromination, optimizing extraction time, adapting cleanup and fractionation steps, and replacing liquid chromatography with high-resolution gas chromatography to separate PBDFs from interfering PBDEs before mass spectrome
This document describes a new method for determining levels of the toxic compound 3-chloropropanediol (3-MCPD) in soy sauce samples. The method involves liquid phase extraction to isolate 3-MCPD from the soy sauce matrix, followed by microwave-assisted derivatization with acetophenone to form a derivative suitable for detection by HPLC-UV. The researchers optimized the derivatization reaction conditions and chromatographic separation. They demonstrated that maximum derivatization could be achieved in just 10 minutes under microwave irradiation, much faster than the conventional 18-hour refluxing method. The new method provides a simple, rapid procedure for analyzing 3-MCPD in soy sauce at trace levels down to 80
Novel approach to synthesis of pentofurano nucleoside assisted natural phosph...Alexander Decker
This document describes a novel method for synthesizing various ribonucleosides using natural phosphate doped with CF3SO3H (NP/CF3SO3H) as a catalyst. Several ribonucleosides were prepared from 1-O-acetyl-2,3,5-tri-O-benzoyl-β-D-ribofuranoside and silylated nucleobases under mild conditions using NP/CF3SO3H. The reaction proceeded through an oxonium intermediate to provide the desired nucleosides in good yields ranging from 20-35%. The method was found to be regioselective, stereoselective, simple, efficient and environmentally friendly for synthesizing various D
Supercritical fluid (CO2) chromatography for quantitative determination of se...Ratnakaram Venkata Nadh
In the present study, two cancer therapeutic drugs (docetaxel and bortezomib) were separated from their
potential impurities on a chromatographic platform by utilizing CO2 gas (supercritical state) and quantified.
The chromatographic separations were achieved on two short columns BEH-2EP (100mm 3mm, 1.7 mm)
and CHIRALPAK AD-3 (100 mm 4.6 mm, 3 mm) for docetaxel and bortezomib, respectively. The present
work describes the role of organic modifiers in the separation of polar compounds by supercritical fluid
chromatography. The two new methods were fully validated in accordance with the current ICH
(International Council for Harmonization of technical requirements for pharmaceuticals for human use)
guidelines. The stability indicating power of the methods was demonstrated from the stress studies
conducted on the injection formulations of the two compounds. The methods are precise with % RSD of
0.4, linear with the correlation coefficient of r2 $ 0.999 and accurate in the range of 50–150% of the
target assay concentration. The two methods can be equally employed for the assay determination of
docetaxel and bortezomib APIs as well.
Feasibility study of mtbe physical adsorption from polluted water on gac, pac...eSAT Publishing House
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology
Feasibility study of mtbe physical adsorption from polluted water on gac, pac...eSAT Journals
Abstract MTBE or Methyl Tertiary Butyl Ether is an organic compound, which is used to increase the gasoline Octane Number. At the beginning of 80’s, by discovering the undesirable effects of tetra ethyl lead usage in fuel, MTBE started to be used worldwide. But gradually the undesirable effects of MTBE on environment had been revealed. There are many technologies for MTBE removal from polluted water. Adsorption is the most conventional and economical technology. In this research, some experiments have been done for studying the adsorption of MTBE on different solid adsorbent in batch process. In these experiments a fixed amount of adsorbents including Granular Activated Carbon (GAC), Powdered Activated Carbon (PAC) and the Husk Rice Carbon (HRC) have been put in different one litter covered vessels containing water polluted with known initial MTBE concentration and stirring them. By measuring MTBE concentration in the vessel at different times the effect of different operating parameters such as temperature and pH have been studied on adsorption and optimum condition have been determined. The batch experimental results have been used to calculate the constant parameters of Freundlich and Langmuir adsorption isotherm equations for these systems. Keywords: MTBE, Adsorption, Activated Carbon, Husk Rice Carbon
Micellar Effect On Dephosphorylation Of Bis-4-Chloro-3,5-Dimethylphenylphosph...IOSR Journals
The rate enhancement depends on the hydrophobicity of the nucleophile. The micellar catalyzed reaction between bis-4-chloro-3,5-dimethylphenylphosphate ester and hydroxide or hydroperoxide anions has been examined in buffered medium (pH 8-10). First order rate constant (Kψ) for the reaction of hydroxide ion with bis-4-CDMPP go through maxima with the increasing concentration of cetyltrimethylammoniumbromide (CTABr). Micelles of CTABr very effective catalyst to the reactions of phosphate diesters. Rate constants measured with OH2- ions are approximately twice and thrice than that of OH- ions in presence of CTABr.
The document describes a modification of an analytical method to allow for the determination of ultratrace levels of polybrominated diphenyl ethers (PBDEs), polybrominated dibenzo-p-dioxins and furans (PBDDs/Fs), and polychlorinated dibenzo-p-dioxins and furans (PCDDs/Fs) from a single combustion flue gas sample. The modifications addressed issues related to photolytic and thermal debromination of brominated compounds. This included optimization of extraction time and solvents, cleanup and fractionation steps, and high-resolution gas chromatography separation. The optimized method enabled quantification of 56 PBDE congeners, 15 PBDD/F
This document describes a method for analyzing ultratrace levels of polybrominated diphenyl ethers (PBDEs), polybrominated dibenzo-p-dioxins and furans (PBDDs/Fs), and polychlorinated dibenzo-p-dioxins and furans (PCDDs/Fs) from combustion flue gas samples. The method was optimized to address potential degradation issues for brominated compounds during extraction, cleanup, and analysis. Modifications included selecting solvents to minimize debromination, optimizing extraction time, adapting cleanup and fractionation steps, and replacing liquid chromatography with high-resolution gas chromatography to separate PBDFs from interfering PBDEs before mass spectrome
This document describes a new method for determining levels of the toxic compound 3-chloropropanediol (3-MCPD) in soy sauce samples. The method involves liquid phase extraction to isolate 3-MCPD from the soy sauce matrix, followed by microwave-assisted derivatization with acetophenone to form a derivative suitable for detection by HPLC-UV. The researchers optimized the derivatization reaction conditions and chromatographic separation. They demonstrated that maximum derivatization could be achieved in just 10 minutes under microwave irradiation, much faster than the conventional 18-hour refluxing method. The new method provides a simple, rapid procedure for analyzing 3-MCPD in soy sauce at trace levels down to 80
Novel approach to synthesis of pentofurano nucleoside assisted natural phosph...Alexander Decker
This document describes a novel method for synthesizing various ribonucleosides using natural phosphate doped with CF3SO3H (NP/CF3SO3H) as a catalyst. Several ribonucleosides were prepared from 1-O-acetyl-2,3,5-tri-O-benzoyl-β-D-ribofuranoside and silylated nucleobases under mild conditions using NP/CF3SO3H. The reaction proceeded through an oxonium intermediate to provide the desired nucleosides in good yields ranging from 20-35%. The method was found to be regioselective, stereoselective, simple, efficient and environmentally friendly for synthesizing various D
Supercritical fluid (CO2) chromatography for quantitative determination of se...Ratnakaram Venkata Nadh
In the present study, two cancer therapeutic drugs (docetaxel and bortezomib) were separated from their
potential impurities on a chromatographic platform by utilizing CO2 gas (supercritical state) and quantified.
The chromatographic separations were achieved on two short columns BEH-2EP (100mm 3mm, 1.7 mm)
and CHIRALPAK AD-3 (100 mm 4.6 mm, 3 mm) for docetaxel and bortezomib, respectively. The present
work describes the role of organic modifiers in the separation of polar compounds by supercritical fluid
chromatography. The two new methods were fully validated in accordance with the current ICH
(International Council for Harmonization of technical requirements for pharmaceuticals for human use)
guidelines. The stability indicating power of the methods was demonstrated from the stress studies
conducted on the injection formulations of the two compounds. The methods are precise with % RSD of
0.4, linear with the correlation coefficient of r2 $ 0.999 and accurate in the range of 50–150% of the
target assay concentration. The two methods can be equally employed for the assay determination of
docetaxel and bortezomib APIs as well.
Feasibility study of mtbe physical adsorption from polluted water on gac, pac...eSAT Publishing House
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology
Feasibility study of mtbe physical adsorption from polluted water on gac, pac...eSAT Journals
Abstract MTBE or Methyl Tertiary Butyl Ether is an organic compound, which is used to increase the gasoline Octane Number. At the beginning of 80’s, by discovering the undesirable effects of tetra ethyl lead usage in fuel, MTBE started to be used worldwide. But gradually the undesirable effects of MTBE on environment had been revealed. There are many technologies for MTBE removal from polluted water. Adsorption is the most conventional and economical technology. In this research, some experiments have been done for studying the adsorption of MTBE on different solid adsorbent in batch process. In these experiments a fixed amount of adsorbents including Granular Activated Carbon (GAC), Powdered Activated Carbon (PAC) and the Husk Rice Carbon (HRC) have been put in different one litter covered vessels containing water polluted with known initial MTBE concentration and stirring them. By measuring MTBE concentration in the vessel at different times the effect of different operating parameters such as temperature and pH have been studied on adsorption and optimum condition have been determined. The batch experimental results have been used to calculate the constant parameters of Freundlich and Langmuir adsorption isotherm equations for these systems. Keywords: MTBE, Adsorption, Activated Carbon, Husk Rice Carbon
Micellar Effect On Dephosphorylation Of Bis-4-Chloro-3,5-Dimethylphenylphosph...IOSR Journals
The rate enhancement depends on the hydrophobicity of the nucleophile. The micellar catalyzed reaction between bis-4-chloro-3,5-dimethylphenylphosphate ester and hydroxide or hydroperoxide anions has been examined in buffered medium (pH 8-10). First order rate constant (Kψ) for the reaction of hydroxide ion with bis-4-CDMPP go through maxima with the increasing concentration of cetyltrimethylammoniumbromide (CTABr). Micelles of CTABr very effective catalyst to the reactions of phosphate diesters. Rate constants measured with OH2- ions are approximately twice and thrice than that of OH- ions in presence of CTABr.
Micellar Effect On Dephosphorylation Of Bis-4-Chloro-3,5-Dimethylphenylphosph...IOSR Journals
The rate enhancement depends on the hydrophobicity of the nucleophile. The micellar catalyzed reaction between bis-4-chloro-3,5-dimethylphenylphosphate ester and hydroxide or hydroperoxide anions has been examined in buffered medium (pH 8-10). First order rate constant (Kψ) for the reaction of hydroxide ion with bis-4-CDMPP go through maxima with the increasing concentration of cetyltrimethylammoniumbromide (CTABr). Micelles of CTABr very effective catalyst to the reactions of phosphate diesters. Rate constants measured with OH2- ions are approximately twice and thrice than that of OH- ions in presence of CTABr.
Toxic Equivalency Factors for Dioxin-Like PCBsv2zq
This document summarizes a consultation held by the WHO-ECEH and IPCS to derive toxic equivalency factors (TEFs) for dioxin-like polychlorinated biphenyls (PCBs). Researchers collected data on the relative toxicities of PCBs compared to 2,3,7,8-tetrachlorodibenzo-p-dioxin (TCDD) from studies. At the consultation, they analyzed the data to define criteria for TEFs and derive TEFs for 13 PCBs. TEFs indicate the relative toxicity of PCBs compared to TCDD. The consultation recommended expanding the project to include more compounds and exploring separate TEFs for different applications like
Application of COSMO-RS-DARE as a Tool for Testing Consistency of Solubility ...Maciej Przybyłek
This study examined the solubility of coumarin, a naturally occurring compound, in various alcohols using experimental and computational methods. Inconsistencies were found in literature solubility data for coumarin. The study developed a theoretical approach using COSMO-RS-DARE modeling to test solubility data consistency and identify outliers. Experimentally measured solubility data for coumarin in a series of alcohols matched the back-calculated COSMO-RS-DARE values, validating the theoretical approach. Linear regressions were also developed to correlate COSMO-RS-DARE integration parameters with molecular descriptors.
The document provides information on the staff members and grant holders of the Analytical Chemistry department for 2008. It summarizes several projects conducted by the department including developing analytical methods to determine pesticides, PAHs, toxins and antibiotics in food and environmental samples. Methods included liquid and gas chromatography coupled with various detectors. Electroanalytical procedures were also considered to reduce sample preparation time and amounts of solvent used. Validation of developed methods revealed good performance. The document outlines goals for 2009 which include characterizing stone deterioration, developing new sensor technologies, and further analysis of contaminants in different matrices like fish and water.
This document summarizes information about 2,3,7,8-tetrachlorodibenzo-para-dioxin (TCDD), 2,3,4,7,8-pentachlorodibenzofuran (PeCDF), and 3,3',4,4',5-pentachlorobiphenyl (PCB 126). It describes their identification, occurrence, use, human exposure including occupational exposure, and background levels found in tissues. TCDD is an unintended byproduct formed during production of chlorophenols and herbicides. PeCDF is emitted from combustion sources while PCBs were commercially produced but their manufacture stopped in 1977 due to environmental contamination. Human exposures can
This document summarizes a study on the synthesis of bromo and chloro derivatives of Baylis–Hillman adducts derived from nitroolefins. The researchers developed a simple protocol to synthesize these derivatives in good yields. They treated Baylis–Hillman adducts derived from nitroolefins with hydrobromic acid or iron chloride to obtain the bromo or chloro derivatives. The derivatives were characterized using NMR, IR and mass spectrometry. The novel bromo and chloro derivatives were shown to have potential as building blocks for a wide variety of organic compounds.
This document describes a study on using different forms of polyaniline (PANI) - Emeraldine Base PANI (EB-PANI), Emeraldine Salt PANI (ES-PANI), and Leuco Emeraldine Base PANI (LEB-PANI) - as sensing materials for detecting dissolved oxygen levels in solutions. The PANI forms were characterized using UV-Vis spectroscopy and their oxygen sensitivity was evaluated using cyclic voltammetry. The cyclic voltammetry measurements showed variations in current corresponding to different oxygen concentrations, indicating the potential of using PANI-coated electrodes as dissolved oxygen sensors. In particular, results showed LEB-PANI may be suitable for detecting low concentrations of dissolved oxygen in
This document reports on a study of the photophysical and electroluminescent properties of a conjugated-nonconjugated multi-block copolymer. Time-resolved fluorescence experiments and comparisons of solution and solid state fluorescence indicate that in the solid state, emission comes from associated species like ground state dimers or excimers, rather than isolated chromophores. Absorption, fluorescence, FTIR and NMR spectroscopy were used to characterize the materials. Light-emitting diodes were fabricated using the copolymer to study its electroluminescent properties.
Simultaneous Electrochemical Measurement using Paper Fluidic Channel on CMOS ...TELKOMNIKA JOURNAL
This paper described the new system of biosensing using CMOS chip. The system was expected
to be used in various circumstances because it was suitable for miniaturization compared to the
conventional system. To conduct electrochemical measurements, the new system used paper fluidic
channel set on the CMOS chip to transport solution to the on-chip electrodes. The materials of paper fluidic
channel were only paper and silicone resin, and these were biocompatible. In experiment, we carried out
simultaneous detection of glucose and ethanol in liquid sample solutions on the 5mm square CMOS chip
and paper fluidic channel. Furthermore, this system can detect various target molecules in addition to
glucose and ethanol, and increase number of simultaneous measurement by adding some more process
to the paper and CMOS chip.
This document outlines a study investigating the cage effects of ionic liquids. The goals are to synthesize naphthyl ester starting materials and purify them for use in a photo-Fries reaction probe experiment to quantify cage effects. Naphthyl esters were synthesized from naphthols and acid chlorides. The esters were purified using recrystallization or column chromatography and analyzed for purity using melting point, TLC, and GC/MS. The purified esters will be used in future photolysis experiments coupled with GC/MS to quantify cage effects of ionic liquids and hexanes as a control. This will provide insight into how effectively solute molecules can escape solvent cages in ionic liquids.
Synthesis of graphene oxide-TiO2 nanocomposite as an adsorbent for the enrich...Nanomedicine Journal (NMJ)
Abstract
Objective(s):
In our study, graphene oxide-TiO2 nanocomposite (GO/TiO2) was prepared and used for the enrichment of rutin from real samples for the first time.
Materials and Methods:
The synthesized GO/TiO2 was characterized by X-ray diffraction, scanning electron microscopy, and FT-IR spectra. The enrichment process is fast and highly efficient. The factors including contact time, pH, and amount of GO/TiO2 affecting the adsorption process were studied.
Results:
The maximum adsorption capacity for ciprofloxacin was calculated to be 59.5 mg/g according to the Langmuir adsorption isotherm. The method yielded a linear calibration curve in the concentration ranges from 15 to 200 μg/L for the rutin with regression coefficients (r2) of 0.9990. The limits of detection (LODs, S/N=3) and limits of quantification (LOQs, S/N=10) were found to be 8 μg/Land 28 μg/L, respectively. Both the intra-day and inter-day precisions (RSDs) were < 10% .
Conclusion:
The developed approach offered wide linear range, and good reproducibility. Owing to the diverse structures and unique characteristic, GO/TiO2 possesses great potential in the enrichment and analysis of trace rutin in real aqueous samples.
A short description of thermal technologies for the recovery of ammonia from N-rich wastewaters and expirementing with membrane distillation for getting better results.
Finding the Right Solvent: A Novel Screening Protocol for Identifying Environ...Maciej Przybyłek
This study investigated the solubility of benzenesulfonamide (BSA) as a model compound using experimental and computational methods. New experimental solubility data were collected in the solvents DMSO, DMF, 4FM, and their binary mixtures with water. The predictive model was constructed based on the best-performing regression models trained on available experimental data, and their hyperparameters were optimized using a newly developed Python code. To evaluate the models, a novel scoring function was formulated, considering not only the accuracy but also the bias–variance tradeoff through a learning curve analysis. An ensemble approach was adopted by selecting the top-performing regression models for test and validation subsets. The obtained model accurately back-calculated the experimental data and was used to predict the solubility of BSA in 2067 potential solvents. The analysis of the entire solvent space focused on the identification of solvents with high solubility, a low environmental impact, and affordability, leading to a refined list of potential candidates that meet all three requirements. The proposed procedure has general applicability and can significantly improve the quality and speed of experimental solvent screening.
Experimental and theoretical solubility advantage screening of bi-component s...Maciej Przybyłek
This document describes an experimental and theoretical study to screen potential solubilizers for curcumin. In the experimental phase, the solubility of curcumin was measured in binary mixtures with 24 excipients. The highest solubility enhancement was found with pyrogallol, caffeine, theophylline, and nicotinamide. A theoretical QSPR model was then developed using molecular descriptors to predict solubility. This model was applied to screen over 230,000 compounds and predict solubility for curcumin analogs and naturally occurring turmerones to identify new excipients.
A Reliable and High Yielding Method for Isolation of Genomic DNA from Ammi MajusSandip Magdum
The developed protocol describes a cheaper, quicker and reliable method for the isolation of pure DNA from medicinal herbs, such as Ammi majus, which produces the secondary metabolites xanthotoxin and berganpectane having immense medicinal importance. Use of CTAB, liquid nitrogen and EDTA in different isolation protocols analyzed for A. majus, all were ended with polysaccharide and protein contamination with low purity of DNA (A260/280=1.3-1.6), revealed a need for method modification for the inexpensive and rapid isolation of pure DNA. Developed reliable and competent protocol isolated enough pure DNA (A260/280=1.81) without following time consuming lengthy steps and hazardous chemicals used in other protocols, which increase experimental costs, risk, and need expertise to perform. The explained protocol requires few chemicals and little time to obtain pure DNA having yield 688 μg/g of A. majus. A higher quantity of isolated DNA obtained from young fresh leaf samples than from either the callus or stem. A. majus is a pharmaceutically important medicinal herb, and the present protocol aids in the analysis and modification of its genes.
This poster describes analytical operating conditions for analysis of US EPA Method 8260C1, Revision 3, August 2006, and includes BFB tune parameters, calibration details, and a complete MDL and Precision and Accuracy study for almost 100 target compounds at multiple concentrations.
This document describes the development of a fluorescent probe for sensing thiamine (vitamin B1) based on arginine-functionalized graphene quantum dots (Arg-GQDs). Arg-GQDs were synthesized through a one-pot hydrothermal method using citric acid and arginine as carbon and nitrogen precursors. The Arg-GQDs exhibited strong blue fluorescence with a quantum yield of 28.3%. The fluorescence of the Arg-GQDs was selectively quenched by Ag+ ions and recovered upon addition of thiamine, providing the basis for a fluorescence "off-on" probe for thiamine. Central composite design and response surface methodology were used to optimize the detection conditions, including pH, time
Phase equilibrium feasibility studies of free fatty acids extraction from pal...Alexander Decker
This document summarizes a study that investigated the extraction of free fatty acids from palm oil using supercritical carbon dioxide. The study assessed the feasibility of using a thermodynamic model based on UNIFAC to predict phase equilibrium and activity coefficients for the carbon dioxide/fatty acid system. Experimental results were obtained for extract mole fraction at different pressures from 60-180 bars and temperatures of 313.15K and 353.15K. Mass transfer parameters like diffusion coefficient and solubility were also determined. The model predictions matched reasonably well with experimental data.
The Effect of Formic Acid, Hydrogen Peroxyde and Other Conditions on Epoxidiz...ijtsrd
Epoxidized vegetable oil have drawn much attention in recent yearrs, especially in the polymer industry as they are economical, available, environmentally friendly, non noxious and renewable. Cashew nut shell liquid CNSL , an agricultural by product abundantly available in tropical countries such as Vietnam, India, is one of the major and economical resources of naturally occurring phenols. Cardanol a byproduct of CNSL could be epoxidized by reacting carbon carbon double bonds of long unsaturated chain with peracids via the Prileshajev epoxidation process or the conventional process. This paper deals with the epoxidized reaction of cardanol take place in formic acid and hydrogen peroxyde. The results shown that the conversion efficiency of the epoxidized reaction reacheres 80 at 600C, stirring rates 1800 rpm, 2 p toluenesulfonic acid catalyst and rate of double bonds DB HCOOH AF H2O2 = 1.0 0.5 1.5. The product of epoxidized cardanol is also characterized by FT IR, 1H NMR and13C NMR. Bach Trong Phuc | Nguyen Thanh Liem "The Effect of Formic Acid, Hydrogen Peroxyde and Other Conditions on Epoxidized Reaction of Cardanol Extracted from Cashew Nut Shell Liquid of Vietnam" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-6 | Issue-3 , April 2022, URL: https://www.ijtsrd.com/papers/ijtsrd49624.pdf Paper URL: https://www.ijtsrd.com/chemistry/polymer-chemistry/49624/the-effect-of-formic-acid-hydrogen-peroxyde-and-other-conditions-on-epoxidized-reaction-of-cardanol-extracted-from-cashew-nut-shell-liquid-of-vietnam/bach-trong-phuc
This document summarizes the results of an experimental campaign to measure emissions of dioxins, furans, and polycyclic aromatic hydrocarbons (PAHs) from a hospital and cemetery waste incinerator. Samples were taken from the afterburning chamber, after the heat exchanger, and at the stack. While pollutant concentrations decreased after the heat exchanger and flue gas treatment systems, emission limits for dioxins were not met at the stack. Emission factors for dioxins through air and solid residues were calculated. Tests with cemetery waste generally showed lower dioxin emission factors than tests with hospital waste. PAH emission factors were within typical ranges reported for other waste incinerators.
This method describes the determination of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans from municipal waste combustors. Samples are collected isokinetically from the gas stream using a glass fiber filter and packed adsorbent column. The compounds are extracted from the sample, separated by gas chromatography, and measured by high resolution mass spectrometry. The document provides details on the sampling apparatus and procedures, reagents, analytical equipment, and quality control checks.
Micellar Effect On Dephosphorylation Of Bis-4-Chloro-3,5-Dimethylphenylphosph...IOSR Journals
The rate enhancement depends on the hydrophobicity of the nucleophile. The micellar catalyzed reaction between bis-4-chloro-3,5-dimethylphenylphosphate ester and hydroxide or hydroperoxide anions has been examined in buffered medium (pH 8-10). First order rate constant (Kψ) for the reaction of hydroxide ion with bis-4-CDMPP go through maxima with the increasing concentration of cetyltrimethylammoniumbromide (CTABr). Micelles of CTABr very effective catalyst to the reactions of phosphate diesters. Rate constants measured with OH2- ions are approximately twice and thrice than that of OH- ions in presence of CTABr.
Toxic Equivalency Factors for Dioxin-Like PCBsv2zq
This document summarizes a consultation held by the WHO-ECEH and IPCS to derive toxic equivalency factors (TEFs) for dioxin-like polychlorinated biphenyls (PCBs). Researchers collected data on the relative toxicities of PCBs compared to 2,3,7,8-tetrachlorodibenzo-p-dioxin (TCDD) from studies. At the consultation, they analyzed the data to define criteria for TEFs and derive TEFs for 13 PCBs. TEFs indicate the relative toxicity of PCBs compared to TCDD. The consultation recommended expanding the project to include more compounds and exploring separate TEFs for different applications like
Application of COSMO-RS-DARE as a Tool for Testing Consistency of Solubility ...Maciej Przybyłek
This study examined the solubility of coumarin, a naturally occurring compound, in various alcohols using experimental and computational methods. Inconsistencies were found in literature solubility data for coumarin. The study developed a theoretical approach using COSMO-RS-DARE modeling to test solubility data consistency and identify outliers. Experimentally measured solubility data for coumarin in a series of alcohols matched the back-calculated COSMO-RS-DARE values, validating the theoretical approach. Linear regressions were also developed to correlate COSMO-RS-DARE integration parameters with molecular descriptors.
The document provides information on the staff members and grant holders of the Analytical Chemistry department for 2008. It summarizes several projects conducted by the department including developing analytical methods to determine pesticides, PAHs, toxins and antibiotics in food and environmental samples. Methods included liquid and gas chromatography coupled with various detectors. Electroanalytical procedures were also considered to reduce sample preparation time and amounts of solvent used. Validation of developed methods revealed good performance. The document outlines goals for 2009 which include characterizing stone deterioration, developing new sensor technologies, and further analysis of contaminants in different matrices like fish and water.
This document summarizes information about 2,3,7,8-tetrachlorodibenzo-para-dioxin (TCDD), 2,3,4,7,8-pentachlorodibenzofuran (PeCDF), and 3,3',4,4',5-pentachlorobiphenyl (PCB 126). It describes their identification, occurrence, use, human exposure including occupational exposure, and background levels found in tissues. TCDD is an unintended byproduct formed during production of chlorophenols and herbicides. PeCDF is emitted from combustion sources while PCBs were commercially produced but their manufacture stopped in 1977 due to environmental contamination. Human exposures can
This document summarizes a study on the synthesis of bromo and chloro derivatives of Baylis–Hillman adducts derived from nitroolefins. The researchers developed a simple protocol to synthesize these derivatives in good yields. They treated Baylis–Hillman adducts derived from nitroolefins with hydrobromic acid or iron chloride to obtain the bromo or chloro derivatives. The derivatives were characterized using NMR, IR and mass spectrometry. The novel bromo and chloro derivatives were shown to have potential as building blocks for a wide variety of organic compounds.
This document describes a study on using different forms of polyaniline (PANI) - Emeraldine Base PANI (EB-PANI), Emeraldine Salt PANI (ES-PANI), and Leuco Emeraldine Base PANI (LEB-PANI) - as sensing materials for detecting dissolved oxygen levels in solutions. The PANI forms were characterized using UV-Vis spectroscopy and their oxygen sensitivity was evaluated using cyclic voltammetry. The cyclic voltammetry measurements showed variations in current corresponding to different oxygen concentrations, indicating the potential of using PANI-coated electrodes as dissolved oxygen sensors. In particular, results showed LEB-PANI may be suitable for detecting low concentrations of dissolved oxygen in
This document reports on a study of the photophysical and electroluminescent properties of a conjugated-nonconjugated multi-block copolymer. Time-resolved fluorescence experiments and comparisons of solution and solid state fluorescence indicate that in the solid state, emission comes from associated species like ground state dimers or excimers, rather than isolated chromophores. Absorption, fluorescence, FTIR and NMR spectroscopy were used to characterize the materials. Light-emitting diodes were fabricated using the copolymer to study its electroluminescent properties.
Simultaneous Electrochemical Measurement using Paper Fluidic Channel on CMOS ...TELKOMNIKA JOURNAL
This paper described the new system of biosensing using CMOS chip. The system was expected
to be used in various circumstances because it was suitable for miniaturization compared to the
conventional system. To conduct electrochemical measurements, the new system used paper fluidic
channel set on the CMOS chip to transport solution to the on-chip electrodes. The materials of paper fluidic
channel were only paper and silicone resin, and these were biocompatible. In experiment, we carried out
simultaneous detection of glucose and ethanol in liquid sample solutions on the 5mm square CMOS chip
and paper fluidic channel. Furthermore, this system can detect various target molecules in addition to
glucose and ethanol, and increase number of simultaneous measurement by adding some more process
to the paper and CMOS chip.
This document outlines a study investigating the cage effects of ionic liquids. The goals are to synthesize naphthyl ester starting materials and purify them for use in a photo-Fries reaction probe experiment to quantify cage effects. Naphthyl esters were synthesized from naphthols and acid chlorides. The esters were purified using recrystallization or column chromatography and analyzed for purity using melting point, TLC, and GC/MS. The purified esters will be used in future photolysis experiments coupled with GC/MS to quantify cage effects of ionic liquids and hexanes as a control. This will provide insight into how effectively solute molecules can escape solvent cages in ionic liquids.
Synthesis of graphene oxide-TiO2 nanocomposite as an adsorbent for the enrich...Nanomedicine Journal (NMJ)
Abstract
Objective(s):
In our study, graphene oxide-TiO2 nanocomposite (GO/TiO2) was prepared and used for the enrichment of rutin from real samples for the first time.
Materials and Methods:
The synthesized GO/TiO2 was characterized by X-ray diffraction, scanning electron microscopy, and FT-IR spectra. The enrichment process is fast and highly efficient. The factors including contact time, pH, and amount of GO/TiO2 affecting the adsorption process were studied.
Results:
The maximum adsorption capacity for ciprofloxacin was calculated to be 59.5 mg/g according to the Langmuir adsorption isotherm. The method yielded a linear calibration curve in the concentration ranges from 15 to 200 μg/L for the rutin with regression coefficients (r2) of 0.9990. The limits of detection (LODs, S/N=3) and limits of quantification (LOQs, S/N=10) were found to be 8 μg/Land 28 μg/L, respectively. Both the intra-day and inter-day precisions (RSDs) were < 10% .
Conclusion:
The developed approach offered wide linear range, and good reproducibility. Owing to the diverse structures and unique characteristic, GO/TiO2 possesses great potential in the enrichment and analysis of trace rutin in real aqueous samples.
A short description of thermal technologies for the recovery of ammonia from N-rich wastewaters and expirementing with membrane distillation for getting better results.
Finding the Right Solvent: A Novel Screening Protocol for Identifying Environ...Maciej Przybyłek
This study investigated the solubility of benzenesulfonamide (BSA) as a model compound using experimental and computational methods. New experimental solubility data were collected in the solvents DMSO, DMF, 4FM, and their binary mixtures with water. The predictive model was constructed based on the best-performing regression models trained on available experimental data, and their hyperparameters were optimized using a newly developed Python code. To evaluate the models, a novel scoring function was formulated, considering not only the accuracy but also the bias–variance tradeoff through a learning curve analysis. An ensemble approach was adopted by selecting the top-performing regression models for test and validation subsets. The obtained model accurately back-calculated the experimental data and was used to predict the solubility of BSA in 2067 potential solvents. The analysis of the entire solvent space focused on the identification of solvents with high solubility, a low environmental impact, and affordability, leading to a refined list of potential candidates that meet all three requirements. The proposed procedure has general applicability and can significantly improve the quality and speed of experimental solvent screening.
Experimental and theoretical solubility advantage screening of bi-component s...Maciej Przybyłek
This document describes an experimental and theoretical study to screen potential solubilizers for curcumin. In the experimental phase, the solubility of curcumin was measured in binary mixtures with 24 excipients. The highest solubility enhancement was found with pyrogallol, caffeine, theophylline, and nicotinamide. A theoretical QSPR model was then developed using molecular descriptors to predict solubility. This model was applied to screen over 230,000 compounds and predict solubility for curcumin analogs and naturally occurring turmerones to identify new excipients.
A Reliable and High Yielding Method for Isolation of Genomic DNA from Ammi MajusSandip Magdum
The developed protocol describes a cheaper, quicker and reliable method for the isolation of pure DNA from medicinal herbs, such as Ammi majus, which produces the secondary metabolites xanthotoxin and berganpectane having immense medicinal importance. Use of CTAB, liquid nitrogen and EDTA in different isolation protocols analyzed for A. majus, all were ended with polysaccharide and protein contamination with low purity of DNA (A260/280=1.3-1.6), revealed a need for method modification for the inexpensive and rapid isolation of pure DNA. Developed reliable and competent protocol isolated enough pure DNA (A260/280=1.81) without following time consuming lengthy steps and hazardous chemicals used in other protocols, which increase experimental costs, risk, and need expertise to perform. The explained protocol requires few chemicals and little time to obtain pure DNA having yield 688 μg/g of A. majus. A higher quantity of isolated DNA obtained from young fresh leaf samples than from either the callus or stem. A. majus is a pharmaceutically important medicinal herb, and the present protocol aids in the analysis and modification of its genes.
This poster describes analytical operating conditions for analysis of US EPA Method 8260C1, Revision 3, August 2006, and includes BFB tune parameters, calibration details, and a complete MDL and Precision and Accuracy study for almost 100 target compounds at multiple concentrations.
This document describes the development of a fluorescent probe for sensing thiamine (vitamin B1) based on arginine-functionalized graphene quantum dots (Arg-GQDs). Arg-GQDs were synthesized through a one-pot hydrothermal method using citric acid and arginine as carbon and nitrogen precursors. The Arg-GQDs exhibited strong blue fluorescence with a quantum yield of 28.3%. The fluorescence of the Arg-GQDs was selectively quenched by Ag+ ions and recovered upon addition of thiamine, providing the basis for a fluorescence "off-on" probe for thiamine. Central composite design and response surface methodology were used to optimize the detection conditions, including pH, time
Phase equilibrium feasibility studies of free fatty acids extraction from pal...Alexander Decker
This document summarizes a study that investigated the extraction of free fatty acids from palm oil using supercritical carbon dioxide. The study assessed the feasibility of using a thermodynamic model based on UNIFAC to predict phase equilibrium and activity coefficients for the carbon dioxide/fatty acid system. Experimental results were obtained for extract mole fraction at different pressures from 60-180 bars and temperatures of 313.15K and 353.15K. Mass transfer parameters like diffusion coefficient and solubility were also determined. The model predictions matched reasonably well with experimental data.
The Effect of Formic Acid, Hydrogen Peroxyde and Other Conditions on Epoxidiz...ijtsrd
Epoxidized vegetable oil have drawn much attention in recent yearrs, especially in the polymer industry as they are economical, available, environmentally friendly, non noxious and renewable. Cashew nut shell liquid CNSL , an agricultural by product abundantly available in tropical countries such as Vietnam, India, is one of the major and economical resources of naturally occurring phenols. Cardanol a byproduct of CNSL could be epoxidized by reacting carbon carbon double bonds of long unsaturated chain with peracids via the Prileshajev epoxidation process or the conventional process. This paper deals with the epoxidized reaction of cardanol take place in formic acid and hydrogen peroxyde. The results shown that the conversion efficiency of the epoxidized reaction reacheres 80 at 600C, stirring rates 1800 rpm, 2 p toluenesulfonic acid catalyst and rate of double bonds DB HCOOH AF H2O2 = 1.0 0.5 1.5. The product of epoxidized cardanol is also characterized by FT IR, 1H NMR and13C NMR. Bach Trong Phuc | Nguyen Thanh Liem "The Effect of Formic Acid, Hydrogen Peroxyde and Other Conditions on Epoxidized Reaction of Cardanol Extracted from Cashew Nut Shell Liquid of Vietnam" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-6 | Issue-3 , April 2022, URL: https://www.ijtsrd.com/papers/ijtsrd49624.pdf Paper URL: https://www.ijtsrd.com/chemistry/polymer-chemistry/49624/the-effect-of-formic-acid-hydrogen-peroxyde-and-other-conditions-on-epoxidized-reaction-of-cardanol-extracted-from-cashew-nut-shell-liquid-of-vietnam/bach-trong-phuc
Similar to New strategy for analysis of PCDF.pdf (20)
This document summarizes the results of an experimental campaign to measure emissions of dioxins, furans, and polycyclic aromatic hydrocarbons (PAHs) from a hospital and cemetery waste incinerator. Samples were taken from the afterburning chamber, after the heat exchanger, and at the stack. While pollutant concentrations decreased after the heat exchanger and flue gas treatment systems, emission limits for dioxins were not met at the stack. Emission factors for dioxins through air and solid residues were calculated. Tests with cemetery waste generally showed lower dioxin emission factors than tests with hospital waste. PAH emission factors were within typical ranges reported for other waste incinerators.
This method describes the determination of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans from municipal waste combustors. Samples are collected isokinetically from the gas stream using a glass fiber filter and packed adsorbent column. The compounds are extracted from the sample, separated by gas chromatography, and measured by high resolution mass spectrometry. The document provides details on the sampling apparatus and procedures, reagents, analytical equipment, and quality control checks.
El documento habla sobre chimeneas y ventiladores. Explica que las chimeneas de ladrillo, hormigón y acero están sujetas a formar grietas y fugas con el tiempo. También describe cómo funciona el tiro natural de una chimenea y los factores que afectan su valor. Finalmente, detalla los diferentes tipos de ventiladores y sus usos, así como leyes básicas relacionadas a cambios en la velocidad, densidad y tamaño de los ventiladores.
El documento describe las principales fuentes de emisiones de gases de efecto invernadero procedentes de la agricultura, incluyendo la ganadería, el cultivo de arroz bajo riego, la quema de sabanas y residuos agrícolas, y las emisiones de suelos agrícolas. También explica los procesos por los cuales se producen las emisiones de metano, óxido nitroso y otros gases como resultado de la fermentación entérica en el ganado, el manejo de estiércol y las quemas agrícolas.
This document provides guidelines for boiler installation, start-up, water treatment and lay-up. It discusses performing a boil out of new boilers using trisodium phosphate and caustic soda to clean internal surfaces. For steam systems, it recommends connecting the boiler to the header to purge piping of debris using steam before reconnecting the condensate system. Proper pretreatment of make-up water is essential before boiler start-up. Guidelines are provided for short and long term lay-up of boilers when taken offline.
Este documento presenta una guía metodológica para la formulación y diseño de sistemas de acueducto rurales en Colombia. Explica los estudios previos, parámetros de diseño y procedimientos requeridos para el diseño detallado de cada componente, incluyendo captaciones, conducciones, tanques, redes y tratamiento. Además, indica los trámites ante autoridades ambientales y presenta un ejemplo completo de aplicación de la metodología.
Optimizing Post Remediation Groundwater Performance with Enhanced Microbiolog...Joshua Orris
Results of geophysics and pneumatic injection pilot tests during 2003 – 2007 yielded significant positive results for injection delivery design and contaminant mass treatment, resulting in permanent shut-down of an existing groundwater Pump & Treat system.
Accessible source areas were subsequently removed (2011) by soil excavation and treated with the placement of Emulsified Vegetable Oil EVO and zero-valent iron ZVI to accelerate treatment of impacted groundwater in overburden and weathered fractured bedrock. Post pilot test and post remediation groundwater monitoring has included analyses of CVOCs, organic fatty acids, dissolved gases and QuantArray® -Chlor to quantify key microorganisms (e.g., Dehalococcoides, Dehalobacter, etc.) and functional genes (e.g., vinyl chloride reductase, methane monooxygenase, etc.) to assess potential for reductive dechlorination and aerobic cometabolism of CVOCs.
In 2022, the first commercial application of MetaArray™ was performed at the site. MetaArray™ utilizes statistical analysis, such as principal component analysis and multivariate analysis to provide evidence that reductive dechlorination is active or even that it is slowing. This creates actionable data allowing users to save money by making important site management decisions earlier.
The results of the MetaArray™ analysis’ support vector machine (SVM) identified groundwater monitoring wells with a 80% confidence that were characterized as either Limited for Reductive Decholorination or had a High Reductive Reduction Dechlorination potential. The results of MetaArray™ will be used to further optimize the site’s post remediation monitoring program for monitored natural attenuation.
Improving the viability of probiotics by encapsulation methods for developmen...Open Access Research Paper
The popularity of functional foods among scientists and common people has been increasing day by day. Awareness and modernization make the consumer think better regarding food and nutrition. Now a day’s individual knows very well about the relation between food consumption and disease prevalence. Humans have a diversity of microbes in the gut that together form the gut microflora. Probiotics are the health-promoting live microbial cells improve host health through gut and brain connection and fighting against harmful bacteria. Bifidobacterium and Lactobacillus are the two bacterial genera which are considered to be probiotic. These good bacteria are facing challenges of viability. There are so many factors such as sensitivity to heat, pH, acidity, osmotic effect, mechanical shear, chemical components, freezing and storage time as well which affects the viability of probiotics in the dairy food matrix as well as in the gut. Multiple efforts have been done in the past and ongoing in present for these beneficial microbial population stability until their destination in the gut. One of a useful technique known as microencapsulation makes the probiotic effective in the diversified conditions and maintain these microbe’s community to the optimum level for achieving targeted benefits. Dairy products are found to be an ideal vehicle for probiotic incorporation. It has been seen that the encapsulated microbial cells show higher viability than the free cells in different processing and storage conditions as well as against bile salts in the gut. They make the food functional when incorporated, without affecting the product sensory characteristics.
Kinetic studies on malachite green dye adsorption from aqueous solutions by A...Open Access Research Paper
Water polluted by dyestuffs compounds is a global threat to health and the environment; accordingly, we prepared a green novel sorbent chemical and Physical system from an algae, chitosan and chitosan nanoparticle and impregnated with algae with chitosan nanocomposite for the sorption of Malachite green dye from water. The algae with chitosan nanocomposite by a simple method and used as a recyclable and effective adsorbent for the removal of malachite green dye from aqueous solutions. Algae, chitosan, chitosan nanoparticle and algae with chitosan nanocomposite were characterized using different physicochemical methods. The functional groups and chemical compounds found in algae, chitosan, chitosan algae, chitosan nanoparticle, and chitosan nanoparticle with algae were identified using FTIR, SEM, and TGADTA/DTG techniques. The optimal adsorption conditions, different dosages, pH and Temperature the amount of algae with chitosan nanocomposite were determined. At optimized conditions and the batch equilibrium studies more than 99% of the dye was removed. The adsorption process data matched well kinetics showed that the reaction order for dye varied with pseudo-first order and pseudo-second order. Furthermore, the maximum adsorption capacity of the algae with chitosan nanocomposite toward malachite green dye reached as high as 15.5mg/g, respectively. Finally, multiple times reusing of algae with chitosan nanocomposite and removing dye from a real wastewater has made it a promising and attractive option for further practical applications.
Evolving Lifecycles with High Resolution Site Characterization (HRSC) and 3-D...Joshua Orris
The incorporation of a 3DCSM and completion of HRSC provided a tool for enhanced, data-driven, decisions to support a change in remediation closure strategies. Currently, an approved pilot study has been obtained to shut-down the remediation systems (ISCO, P&T) and conduct a hydraulic study under non-pumping conditions. A separate micro-biological bench scale treatability study was competed that yielded positive results for an emerging innovative technology. As a result, a field pilot study has commenced with results expected in nine-twelve months. With the results of the hydraulic study, field pilot studies and an updated risk assessment leading site monitoring optimization cost lifecycle savings upwards of $15MM towards an alternatively evolved best available technology remediation closure strategy.
1. Journal of Chromatography A, 998 (2003) 169–181
www.elsevier.com/locate/chroma
New strategy for comprehensive analysis of polybrominated
diphenyl ethers, polychlorinated dibenzo-p-dioxins, polychlorinated
dibenzofurans and polychlorinated biphenyls by gas chromatography
coupled with mass spectrometry
*
Catherine Pirard , Edwin De Pauw, Jean-François Focant
Mass Spectrometry Laboratory, University of Liege, Allee de la Chimie 3, Bat. B6c Sart-Tilman, B-4000 Liege, Belgium
Received 24 October 2002; received in revised form 3 April 2003; accepted 3 April 2003
Abstract
A strategy for determination of polybrominated diphenyl ethers, polychlorinated dibenzodioxins, polychlorinated
dibenzofurans and polychlorinated biphenyls on fatty matrices has been established. After extraction, the proposed method
allows the purification and the fractionation of all target groups of compounds in a simple multi-step automated clean-up.
Furthermore, their subsequent analysis is carried out using a single benchtop mass spectrometer, in four separate injections.
Required sensitivity considering levels found in the environment is attained using electron impact ionisation followed by
tandem in time mass spectrometry. The whole method has been evaluated on standard solution and quality control samples
consisting of fortified beef fat. Sensitivity, selectivity, accuracy and repeatability were tested with satisfactory results.
2003 Elsevier Science B.V. All rights reserved.
Keywords: Polybrominated diphenyl ethers; Polychlorinated dibenzodioxins; Polychlorinated dibenzofurans; Polychlorinated
biphenyls; Organochlorine compounds; Organobromine compounds; Halogenated compounds
1. Introduction regarding these compounds is that they can later
migrate out of the finished products and be released
Polybrominated diphenyl ethers (PBDEs) are man- into the environment [1]. Like polychlorinated di-
made chemicals used as additive flame retardants. benzo-p-dioxins (PCDDs), polychlorinated dibenzo-
They are incorporated into polymers in order to furans (PCDFs) and polychlorinated biphenyls
inhibit or slow down both ignition and rate of (PCBs), they are persistent and lipophilic compounds
combustion. They find their major applications as and therefore have a tendency to bioaccumulate
incorporated chemicals in various plastics, textiles, through the trophic pyramid and reach human via the
wire, cable insulation, electrical/electronic connec- food chain [1,2].
tors and other everyday products. The concern In 1981, Andersson and Blomkvist were among
the first to report the presence of these or-
ganohalogen compounds in Swedish fish samples
*Corresponding author. Tel.: 132-4-366-3531; fax: 132-4-
´
[3]. Twenty years later, still in Sweden, Noren and
366-4387.
´
E-mail address: catherine.pirard@ulg.ac.be (C. Pirard). Meironyte reported a drastic increase of these com-
0021-9673/03/$ – see front matter 2003 Elsevier Science B.V. All rights reserved.
doi:10.1016/S0021-9673(03)00611-3
2. 170 C. Pirard et al. / J. Chromatogr. A 998 (2003) 169–181
pounds in human breast milk, incontestable evidence requires a very highly selective purification method
that humans are currently exposed to these kinds of to eliminate these interferences. Nowadays analysis
compounds [4]. Conversely to what is observed for using EI of PBDEs in solution containing PCBs is
most anthropogenic organic pollutants, levels of not conceivable using single-dimensional GC.
PBDEs found in the environment have incessantly The aim of the present study was to elaborate a
increased in the last 20 years world-wide, sometimes strategy for the analysis of a broad range of or-
being higher than PCB levels [2,5–9]. Nowadays, ganohalogen compounds, including, on one hand,
occurrence of PBDEs are a cause of growing con- brominated compounds (PBDEs), and on the other
cern, and more and more laboratories have to offer hand, chlorinated compounds such as PCDDs,
the capability to analyse this class of contaminant, PCDFs and PCBs. Experienced in the use of auto-
which has begun to be included in monitoring mated clean-up systems for PCDD/F and PCB
programs. Therefore, a rapid, reliable, time- and purifications, we decided to investigate the poten-
resource-saving analysis method is needed. tiality to extend our current methods to PBDEs
Analysis of PBDEs in biological samples usually without excessive changes.
consists of a lipid extraction step using combination As we had previously reported on the suitability of
of polar and non-polar solvent. Most frequently, quadruple ion storage mass spectrometry (QISMS)
Soxhlet or pressurised liquid extraction (PLE) are for PCDD/F and PCB analysis using EI-MS–MS
used and, to a lesser extent and as for PCDD/Fs and [16,17], we decided to maintain the EI mode in
PCBs, supercritical fluid extraction (SFE) can be conjunction with MS–MS for PBDE analysis. This
also used [2,6,10]. Further clean-up is currently combination would avoid interferences such as those
performed using gel permeation chromatography or mentioned above and would allow determination of
sulfuric acidic treatment to remove lipids before PBDEs in solutions holding other organohalogen
additional adsorption chromatography to eliminate compounds such as PCBs. To our knowledge, there
co-extracted substances [6,10,11]. The final determi- are to date no results available on the analysis of
nation is generally carried out by gas chromatog- PBDEs by EI-MS–MS. It should be noted that
raphy (GC) coupled with mass spectrometry (MS) or decabrominated diphenyl ether which is the most
electron-capture detection (ECD), the latter being important commercial product with regard to the
much less selective [10]. Negative chemical ionisa- production and use among the brominated diphenyl
tion (NCI) is the most often used ionisation mode for ethers (mono- to deca-), will be not investigated due
determination of brominated compounds by MS. to the considerable difficulties in its analysis. This
Such a technique presents a higher sensitivity than highly brominated compound actually requires a
electron impact (EI), but is less selective, since only specific GC column owing to its very long retention
bromine can be monitored, and is less accurate since time [2,18,19]. Nevertheless, although DeBDE used
it does not allow the quantification by internal to be abundant in environmental samples, very low
13
standard ( C-labelled PBDEs) [10,12,13]. EI how- levels were found in biological samples probably due
ever usually requires high-resolution mass spec- to the very poor bioavailability of this kind of highly
trometry (HRMS) to overcome the lack of sensitivity halogenated compound [2,11,18].
of the ionisation mode, whereas low-resolution mass
spectrometry (LRMS) is sufficient when based on
NCI. From a competitive point of view, comparisons 2. Experimental
between EI and NCI have already been realised and
similar suitability was found regarding determination 2.1. Chemicals and reagents
of PBDEs [13–15]. Concerning EI, even if HRMS
provides a high degree of sensitivity and selectivity, Hexane, toluene, ethyl acetate and dichlorome-
¨
it is not free from interferences. For instance, PBDE- thane are Pestanal reagents (Riedel-de Haen, Seelze,
47 uses to co-elute with PCB-180 on a classical 30 m Germany). Nonane (puriss analytical-reagent grade
DB-5 type column and this detector cannot resolve standard for GC) was purchased from Fluka
them in normal operating conditions [14]. This (Steinheim, Germany). Anhydrous sodium sulfate
3. C. Pirard et al. / J. Chromatogr. A 998 (2003) 169–181 171
13
was Baker analysed (J.T. Baker, Deventer, The ethers and five C-labelled PBDEs in nonane.
Netherlands). Liquid nitrogen was purchased at Air Concentrations of each congener of EO-4980 solu-
13
Liquide (Liege, Belgium). The C -labelled inter- tion are listed in Table 1 (PBDE numbering follow-
12
nal standard solution containing dioxins, furans and ing Ballschmiter and Zell rules [20] as for PCBs).
coplanar PCBs was from Cambridge Isotope Labs. The BDE-MXC native solution (Wellington Labs.)
(Andover, MS, USA). This EDF-4144 internal stan- contains 4-MonoBDE (PBDE-3), 2,4-DiBDE
dard solution used for isotopic dilution contains (PBDE-7), 4,49-DiBDE (PBDE-15), 2,29,49-TriBDE
2,3,7,8-TCDD, 1,2,3,7,8-PeCDD, 1,2,3,4,7,8- (PBDE-17), 2,4,49-TriBDE (PBDE-28), 2,29,4,49-
HxCDD, 1,2,3,6,7,8-HxCDD, 1,2,3,7,8,9-HxCDD, TetraBDE (PBDE-47), 2,29,4,59-TetraBDE (PBDE-
1,2,3,4,6,7,8-HpCDD, OCDD, 2,3,7,8-TCDF, 49), 2,39,4,49-TetraBDE (PBDE-66), 2,39,49,6-Tetra-
1,2,3,7,8-PeCDF, 2,3,4,7,8-PeCDF 1,2,3,4,7,8- BDE (PBDE-71), 3,39,4,49-TetraBDE (PBDE-77),
HxCDF, 1,2,3,6,7,8-HxCDF, 1,2,3,7,8,9-HxCDF, 2,29,3,4,49-PentaBDE (PBDE-85), 2,29,4,49,5-Penta-
2,3,4,6,7,8-HxCDF, 1,2,3,4,6,7,8-HpCDF, OCDF, BDE (PBDE-99), 2,29,4,49,6-PentaBDE (PBDE-
3,39,4,49-TCB (PCB-77) (PCB numbering following 100), 2,39,4,49,6-PentaBDE (PBDE-119), 3,39,4,49,5-
Ballschmiter and Zell rules [20]), 3,4,49,5-TCB PentaBDE (PBDE-126), 2,29,3,4,49,59-HexaBDE
(PCB-81), 3,39,4,49,5-PeCB (PCB-126) and (PBDE-138), 2,29,4,49,5,59-HexaBDE (PBDE-153),
3,39,4,49,5,59-HxCB (PCB-169) with concentrations 2,29,4,49,5,69-HexaBDE (PBDE-154),
ranging from 24 to 125 pg/ml in nonane [21]. The 2,29,3,4,49,59,6-HeptaBDE (PBDE-183) and decab-
recovery standard solution EDF-4145 (Cambridge romodiphenyl ether (PBDE-209), all these 20 con-
13
Isotope Labs.) contains [ C ]3,39,5,59-TCB (PCB- geners are found at a concentration level of 2 ng/ml.
12
13 13
80) at 48 pg/ml, [ C ]1,2,3,4,7,8,9-HpCDF at 62.5 The MBDE-MXC C-labelled internal standard
12
13
pg/ml and [ C ]1,2,3,4-TCDD at 25 pg/ml in solution was from Wellington Labs. and contains
6
nonane. Multianalyte calibration solutions (EDF- 4-MonoBDE (PBDE-3), 4,49-DiBDE (PBDE-15),
4143, Cambridge Isotope Labs.) were used to calcu- 2,4,49-TriBDE (PBDE-28), 2,29,4,49-TetraBDE
late the relative response factors (RRFs) for each (PBDE-47), 2,29,4,49,5-PentaBDE (PBDE-99),
congener [21]. 2,29,4,49,5,59-HexaBDE (PBDE-153), 2,29,4,49,5,69-
13
The C -labelled internal standard solution con- HexaBDE (PBDE-154) and 2,29,3,4,49,59,6-Hepta-
12
taining non- and mono-ortho PCBs was from Wellin- BDE (PBDE-183) at a concentration level of 5
13
gton Labs. (Ontario, Canada). This WP-LCS internal ng/ml. The MBDE-139 MXC C-labelled internal
standard solution contains 3,39,4,49-TCB (PCB-77), standard solution (Wellington Labs.) contains
3,4,49,5-TCB (PCB-81), 2,3,39,4,49-PeCB (PCB- 2,29,3,4,49,6-HexaBDE (PBDE-139) at a concentra-
105), 2,3,4,49,5-PeCB (PCB-114), 2,39,4,49,5-PeCB tion level of 50 ng/ml.
(PCB-118), 29,3,4,49,5-PeCB (PCB-123), 3,39,4,49,5-
PeCB (PCB-126), 2,3,39,4,49,5-HxCB (PCB-156), 2.2. Samples
2,3,39,4,49,59-HxCB (PCB-157), 2,39,4,49,5,59-HxCB
(PCB-167), 3,39,4,49,5,59-HxCB (PCB-169) and Studies of the elution of the different compounds
13
2,3,39,4,49,5,59-HpCB (PCB-189) at a concentration were performed with C -labelled internal standard
12
level of 1 ng/ml. The MBP-MXE (Aroclor 1260 solution for PCBs and dioxins, and with the ana-
congeners) internal standard solution (Wellington lytical standard solution EO-4980 for elution of
Labs.) contains 2,4,49-TriCB (PCB-28), 2,29,5,59- PBDEs, each of those diluted in hexane. In order to
TCB (PCB-52), 2,29,4,5,59-PeCB (PCB-101), evaluate the accuracy of the multi-analyte method,
2,29,3,4,49,5-HxCB (PCB-138), 2,29,4,49,5,59 HxCB analyses were carried out on ‘‘laboratory-made’’
(PCB-153), 2,29,3,4,49,5,59-HpCB (PCB-180) and quality controls (QCs), which were commercially
decachlorobiphenyl (PCB-209) at a concentration available fortified beef fat. These QC samples con-
level of 5 ng/ml. tained 40.4 pg/g fat (5.3 pg TEQ/g fat) for the 17
The PBDE analytical standard solution EO-4980 PCDD/Fs, 160 pg/g fat (6 pg TEQ/g fat) for the
(Cambridge Isotope Labs.) contains 40 native con- four coplanar PCBs, 4.9 ng/g fat (1 pg TEQ/g fat)
geners from mono- to heptabrominated diphenyl for the eight mono-ortho PCBs, 18 ng/g for Aroclor
4. 172 C. Pirard et al. / J. Chromatogr. A 998 (2003) 169–181
Table 1
PBDE analytical standard solution EO-4980
Congener No. Concentration Congener No. Concentration
(pg/ml) (pg/ml)
Unlabelled BDE 3,39,4,49-TetraBDE 77 100
2,29,3,4,49-PentaBDE 85 150
2-MonoBDE 1 100 2,29,4,49,5-PentaBDE 99 150
3-MonoBDE 2 100 2,29,4,49,6-PentaBDE 100 150
4-MonoBDE 3 100 2,3,39,4,49-PentaBDE 105 150
2,4-DiBDE 7 100 2,3,4,5,6-PentaBDE 116 150
2,49-DiBDE 8 100 2,39,4,49,6-PentaBDE 119 150
2,6-DiBDE 10 100 3,39,4,49,5-PentaBDE 126 150
3,39-DiBDE 11 100 2,29,3,4,49,59-HexaBDE 138 200
3,4-DiBDE 12 100 2,29,3,4,49,69-HexaBDE 140 200
3,49-DiBDE 13 100 2,29,4,49,5,59-HexaBDE 153 200
4,49-DiBDE 15 100 2,29,4,49,5,69-HexaBDE 154 200
2,29,4-TriBDE 17 100 2,29,4,49,6,69-HexaBDE 155 200
2,39,4-TriBDE 25 100 2,3,4,49,5,6-HexaBDE 166 200
2,4,49-TriBDE 28 100 2,29,3,4,49,5,6-HeptaBDE 181 250
2,4,6-TriBDE 30 100 2,29,3,4,49,59,6-HeptaBDE 183 250
2,49,6-TriBDE 32 100 2,3,39,4,49,5,6-HeptaBDE 190 250
13
29,3,4-TriBDE 33 100 C-Labelled BDE
3,39,4-TriBDE 35 100
13
3,4,49-TriBDE 37 100 2,29,4,49-TetraBDE ( C , 99%) 47 100
12
13
2,29,4,49-TetraBDE 47 100 3,39,4,49-TetraBDE ( C , 99%) 77 100
12
13
2,29,4,59-TetraBDE 49 100 2,29,4,49,5-PentaBDE ( C , 99%) 99 150
12
13
2,39,4,49-TetraBDE 66 100 2,29,4,49,6-PentaBDE ( C , 99%) 100 150
12
13
2,39,49,6-TetraBDE 71 100 3,39,4,49,5-PentaBDE ( C , 99%) 126 150
12
2,4,49,6-TetraBDE 75 100
1260 PCBs [22], 100 pg/g for each tetraBDE, 150 [26]. When an extract contains more than 1 g of fat,
pg/g for each pentaBDE and 200 pg/g for each high-capacity disposable silica (HCDS) columns are
hexaBDE. added before the classical silica column. Details on
the efficiency of these columns are described else-
2.3. Sample preparation where [21]. The configuration of the system allows
the operator to collect different fractions at different
Purification steps were based on Power-Prep, a steps of the purification. Collected fractions can be
commercially available automated multi-column further concentrated and analysed by GC–MS.
clean-up system (Fluid Management Systems, Walth-
am, MA, USA). This system has been previously 2.4. Instrumental analysis
described [21–25]. Briefly, the automated clean-up
system is composed of a valve drive module con- All analyses were performed by tandem in time
nected to a pump module responsible for the solvent mass spectrometry (GC–MS–MS) using a Ther-
flow in the valve module. The programming of moQuest Trace GC PolarisQ ion trap mass spec-
solvent volumes, types, flow-rates and directions is trometer (Austin, TX, USA) and a Hewlett-Packard
carried out in software operating under Windows. (Palo Alto, CA, USA) 6890 Series gas chromato-
This system uses disposable multi-layer silica col- graph, the latter equipped with an Rtx 5-MS (40
umns (4 g acid, 2 g base and 1.5 g neutral), basic m30.18 mm, 0.20 mm) capillary column (Restek,
alumina (8 g) and PX-21 (2 g) carbon columns in Evry, France). The ion trap was set at 250 8C, with
order to separate analytes of interest from matrix the transfer line at 300 8C. Electron impact was used
interferences following a previously reported strategy as the ionisation mode, with an energy of 70 eV.
5. C. Pirard et al. / J. Chromatogr. A 998 (2003) 169–181 173
Analysis of PCDD/Fs, PCBs and PBDEs were PTVLV–GC–MS–MS and GC–MS–MS, respective-
carried out following separate injections. ly, has already been optimised using ion trap mass
spectrometry in one of our previous studies [17]. It
2.4.1. Dioxins and furans was demonstrated that use of large volume injection
Determination of dioxins in GC–MS–MS was allowed one to achieve an LOQ between 0.1 and 0.2
already optimised using programmable temperature pg/g fat for all dioxin and furan congeners. The
vaporisation-large volume (PTV-LV) injections in present study does not discuss these results further.
order to increase sensitivity and decrease limits of
quantification (LOQs). Details are described else- 3.1.1. Ionisation
where [17]. EI was chosen as the ionisation mode in order to
allow the use of isotopic dilution as quantification
2.4.2. PCBs method and therefore make the analysis more accur-
GC conditions were optimised to separate the 12 ate. In most studies operating with mass spec-
non- and mono-ortho PCBs and the seven marker trometry based on electron impact, the electron
PCBs as follows: splitless injection of 1 ml at 140 8C, energy was either 70 eV [12,27–29] or 30–40 eV
initial oven temperature of 140 8C for 1 min, then [13,15,30,31]. Knowing that electron energy depends
increased at 25 8C/min to 180 8C held for 1 min, on mass spectrometer characteristics, especially on
then increased at 2 8C/min to 210 8C held for 8 min, source geometry, optimisations were carried out
finally increased at 3 8C/min to 280 8C and held for between 30 and 70 eV in the full-scan mode. The
2 min. He (N60, Air Liquide, France) was used as nature of ions produced during ionisation of PBDEs
the carrier gas. by EI is known to be dependent on the level of
bromination. This ionisation mode has thus been
2.4.3. PBDEs demonstrated to be less sensitive when the number of
The GC temperature program for the separation of bromines increases, making heptaBDE detection
PBDEs, from mono- to hexabrominated homologues very difficult at low concentrations [12]. Most
was optimised as follows: splitless injection of 1 ml studies dedicated to the determination of PBDEs by
at 140 8C, initial oven temperature of 140 8C for 1.5 EI-MS described that spectra obtained after electron
1 1
min, then increased at 20 8C/min to 220 8C held for impact are dominated by M and [M-Br ] species
2
1 min, then increased at 2 8C/min to 280 8C, finally for lowest degrees of bromination and higher bromi-
increased at 30 8C/min to 300 8C and held for nated levels, respectively [12–15,27,30]. Similar
10 min. He (N60, Air Liquide) was used as the trends were observed in the present study, but
carrier gas. differences between congeners of a same family have
1
Quantification was performed using internal stan- however been observed. M species provided the
dards and the isotopic dilution technique. The la- most intense peak for dibrominated congeners except
belled compounds were added to the fat after the for PBDE-7, PBDE-8 and PBDE-10, for which [M-
1
extraction step. Recoveries were calculated using the Br ] gave the predominant peak. For tri- to hexa-
2
recovery standard solution EDF-4145 for PCDD/Fs BDEs, loss of Br led to the most abundant ion with
2
and PCBs, which was added to the reconstituted the exception of triBDE-35 and -37, tetraBDE-77
nonane extracts prior to the injection onto the GC and pentaBDE-126 for which ionisation mainly
system. The standard solution MBDE-139 MXC was yielded to their molecular ion. A common charac-
used to calculate the recoveries of PBDEs. teristic of these congeners is that they have actually
no bromine atom in the ortho position. This was
consistent with observations of Alaee et al. [28] and
3. Results and discussion Marsh et al. [32], who reported that bromine ortho
1
substitution favoured the formation of the [M-Br ]
2
1
3.1. Optimisation of mass spectrometry parameters species over the M species. Whatever the electron
energy (tests were carried out at 30, 40, 50, 60 and
The analysis of PCDD/Fs and PCBs using 70 eV) no significant difference was found in frag-
6. 174 C. Pirard et al. / J. Chromatogr. A 998 (2003) 169–181
mentation process during ionisation or in the intensi- have characteristic daughter ions resulting from the
ty of signal when current was reconstructed with loss of –COCl.
adequate ion masses. Changes in the temperature An opposite trend was observed for lower degree
source had only minor influence on the loss of Br of bromination. Di- and tribrominated congeners lost
2
(220 or 250 8C) and on the ionisation efficiency. For the last bromine atom during the exciting step,
greater convenience, the ion source was been set at except for DiBDE-11, -12 & 13, -15 and TriBDE-35
250 8C and 70 eV was kept as the electron energy. and -37 (which have no bromine atom in the ortho
Table 2 summarises the mass of parent ions that positions) showing more intense peaks in mass
were isolated for each congener. spectra corresponding to loss of –COBr. Optimised
CID voltage as well as daughter ions monitored are
gathered in Table 2.
3.1.2. Fragmentation
Once parent ions were isolated in the trap, they
3.2. Evaluation of the analytical procedure
were fragmented by collision-induced dissociation
(CID) producing daughter ions characteristic of
target molecules. Again, fragmentation of selected 3.2.1. Linearity
ion was congener dependent. Fig. 1 shows mass A five-point calibration curve was determined for
spectra obtained for TBDE-47, TBDE-77, PeBDE-99 the PBDEs of solution EO-4980 excepted for hepta-
and PeBDE-126 after optimisation of CID voltages. BDEs. Linearity was observed for a range of be-
Excitation time and energy of excitation parameters tween 1 and 75 pg for di-, tri- and tetrabrominated
were default ones. congeners, between 1.5 and 112 pg for pentabromi-
For tetra-, penta- and hexabrominated compounds, nated, between 2 and 150 pg for hexabrominated,
non-ortho substituted congeners (TBDE-77 and with satisfactory correlation coefficients. The RRF
PeDBE-126) were fragmented with loss of Br (such varied in a broad range of values depending on the
2
as PCBs lose Cl ) yielding the main ion clusters and congener. This was probably mainly due to the few
2
13
with loss of –COBr in a lesser extent. For other C congeners available. Table 3 presents the RRFs
1 2
congeners, [M-COBr] was the main fragment and for all congeners, correlation coefficients (R ) and
breakage of a single Br bound gave a signal of lower the range of concentration where linearity were
intensity. This behaviour is similar to dioxins which observed.
Table 2
CID voltages, monitored parent ions and daughter ions for each congener
Homologue Congener Isolated parent ion CID voltage Isolated daughter ions
(m/z) (V) (m/z)
12
DiBDEs 10, 7, 11, 8, 12&13, 15 C 328 [M12] 3.75 168, 219/221
13
15 C 340 [M12] 3.75 180
12
TriBDEs 30, 32, 17&25, 28&33 C 246 [M-Br ] 4.0 167
2
13
28 C 258 [M-Br ] 4.0 179
2
12
35, 37 C 406 [M12] 4.0 246/248, 297/299/301
12
TBDEs 75, 71, 49, 47, 66 C 326 [M12-Br ] 5.0 217/219, 245/247
2
13
47 C 338 [M12-Br ] 5.0 229/231, 257/259
2
12
77 C 486 [M14] 4.5 324/326/328, 377/379
12
PeBDEs 100, 119, 99, 116, 85 C 404 [M12-Br ] 5.0 295/297/299, 325/327
2
13
99 C 416 [M12-Br ] 5.0 337/339, 307/309/311
2
12
126 C 564 [M14] 4.5 404/406, 325
12
HxBDEs 154, 153, 140, 138, 166 C 484 [M14-Br ] 5.5 376/378, 403/405
2
13
154, 153 C 496 [M14-Br ] 5.5 388/390, 415/417
2
7. C. Pirard et al. / J. Chromatogr. A 998 (2003) 169–181 175
Fig. 1. Mass spectra obtained after CID voltage optimisation of: (A) TBDE-47, parent ion was [M12-Br ] (m/z 326), (B) TBDE-77, parent
2
ion was [M14] (m/z 486), (C) PeBDE-99, parent ion was [M12-Br ] (m/z 404), (D) PeBDE-126, parent ion was [M14] (m/z 564).
2
3.2.2. Repeatability and reproducibility for HxBDE-138, TBDE-77 and PeBDE-126, but
Repeatability (short-term standard deviation) and remained lower than 18% for latter two. RSDs for
reproducibility (long-term standard deviation) were other congeners ranged between 3 and 12%.
evaluated for our analytical method.
Mixtures of native PBDEs (EO-4980) and MBDE- 3.2.3. Limits of detection
13
MXC C-labelled internal standard solution were Limits of detection (LODs) of the mass spec-
injected 10 times consecutively and relative standard trometer were defined as the smaller amount giving a
deviations (RSDs) between amounts obtained were signal-to-noise ratio greater than 3. These LODs
calculated. These RSD values, which are gathered in ranged between 0.5 and 3 pg depending on the
Table 3, did not exceed 10%, accounting for the congener. Tandem in time mass spectrometry re-
good repeatability of the mass spectrometer response mained slightly less sensitive than HRMS [13], but
in the EI-MS–MS mode. There was no evidence that allowed one to distinctly decrease the LOD com-
RSD increased with increased degree of bromination pared to EI-LRMS [15], especially for higher bromi-
as it was previously observed in another study using nation degree, and nearly achieved the offset of the
EI-MS [15]. lower sensitivity of EI compared to the NCI mode.
Reproducibility was tested by establishing 10 Regarding levels of PBDEs reported in the environ-
calibration curves with the BDE-MXC native solu- ment, MS–MS can really compete with both meth-
13
tion and the MBDE-MXC C-labelled internal ods usually used.
standard solution at different moments, under differ-
ent conditions, with different operators. The RSDs of 3.3. Optimisation of the purification step
the RRFs found for each calibration and for each
congener were evaluated and are reported in Table 3. In the dioxin purification procedure, the automated
The BDE-MXC native solution does not contain as Power-Prep system has already proven its efficiency
many congeners as the EO-4980 solution, data on for various types of matrices such as environmental
reproducibility are missing for some congeners. [23], biological [24] and food-type [25]. A previous
Standard deviation thus slightly increased especially study has extended this multi-step clean-up to 14
8. 176 C. Pirard et al. / J. Chromatogr. A 998 (2003) 169–181
Table 3
2
Concentration range where linearity was tested, relative response factor (RRF), correlation coefficient (R ), short-term relative standard
deviation (repeatability) and long-term relative standard deviation (reproducibility) for PBDEs
2
Concentration RRF R Repeatability, Reproducibility,
range (pg/ml) RSD (%) RSD (%)
DiBDE-10 1–75 0.996 0.997 5.9 –
DiBDE-7 1–75 0.886 0.997 3.1 3.5
DiBDE-11 1–75 2.014 0.994 2.7 –
DiBDE-8 1–75 1.015 0.992 2.2 –
DiBDE-13, -12 1–75 2.217 0.991 1.7 –
DiBDE-15 1–75 0.979 0.996 6.3 9.9
TriBDE-30 1–75 0.718 0.996 5.4 –
TriBDE-32 1–75 0.366 0.993 4.3 –
TriBDE-17, -25 1–75 1.495 0.999 5.2 12.1
TriBDE-28, -33 1–75 1.380 0.990 3.4 12.3
TriBDE-35 1–75 6.407 0.995 4.5 –
TriBDE-37 1–75 3.876 0.995 4.5 –
TBDE-75 1–75 0.724 0.991 4.1 –
TBDE-71 1–75 0.802 0.992 2.2 3.2
TBDE-49 1–75 0.789 0.991 4.8 9.8
TBDE-47 1–75 0.888 0.993 1.1 3.6
TBDE-66 1–75 0.631 0.992 6.5 8.1
TBDE-77 1–75 0.086 0.993 9.5 17.8
PeBDE-100 1.5–112 3.244 0.994 1.9 3.9
PeBDE-119 1.5–112 2.148 0.993 2.2 2.4
PeBDE-99 1.5–112 2.348 0.992 1.2 4.2
PeBDE-116 1.5–112 1.892 0.990 4.1 –
PeBDE-85 1.5–112 1.453 0.988 5.0 11.2
PeBDE-126 1.5–112 0.117 0.994 8.4 17.6
PeBDE-105 1.5–112 0.119 0.991 3.2 –
HxBDE-154 2–150 0.305 0.993 3.0 7.0
HxBDE-153 2–150 0.357 0.994 3.1 7.4
HxBDE-140 2–150 0.158 0.993 1.3 –
HxBDE-138 2–150 0.105 0.993 9.7 14.6
HxBDE-166 2–150 0.052 0.997 2.6 –
PCBs using the same sequence of events constituting hexane (200 ml) was used to elute compounds from
the program for dioxin isolation [22]. The drawback the silica through the alumina column. A mixture (60
of this strategy was the quite high volume of solvent ml) of hexane–dichloromethane (98:2) was then
used for PCB purification, yielding quite high blank applied onto the alumina column where some less-
levels and therefore to quite high LOQs. The present polar PCBs began to elute and were collected. The
study enlarges this clean-up to brominated com- remaining PCBs and dioxins were eluted from
pounds such as PBDEs with optimisation of type and alumina with 120 ml of hexane–dichloromethane
quantities of solvent used to isolate the different (50:50) through the carbon column on which dioxins
compounds carried out in order to produce as low and other coplanar compounds such as non-ortho
LOQs as possible. PCBs (also called c-PCBs) were trapped, while other
Details of the clean-up scheme for dioxin analysis non-planar PCBs passed through it and were col-
on the Power-Prep have been already extensively lected. This fraction was pooled to the ‘‘98:2 frac-
described [21–25]. It consists of a succession of tion’’ and constituted the PCB fraction. An ethyl
three different types of columns (HCDS and multi- acetate–toluene (50:50) mixture (5 ml) was further
layer silica, basic alumina and PX-21 carbon). Once applied to the carbon column in the forward direction
extracted fat was loaded onto the silica columns, for additional clean-up. Afterwards, 65 ml of toluene
9. C. Pirard et al. / J. Chromatogr. A 998 (2003) 169–181 177
was applied to the carbon column in the backflush to be separated from each other. This allowed the
direction for the elution of dioxins and non-ortho simultaneous collection of both families of chemicals
PCBs. in the same fraction. The only condition was to be
Since most of the fractionation process occurs on able to do so quantitatively. The solvent mixture that
the alumina column, depending on the solvent mix- appeared to be the more efficient to elute, spe-
ture used, the isolation of any other related com- cifically those from alumina, was a solution of 20%
pounds such as PBDEs should be studied at that dichloromethane hexane. Fig. 3 depicts the scheme
level. In that optic, the elution pattern of PCDD/Fs, of the optimised clean-up procedure and Table 4
PCBs and PBDEs has been investigated on alumina shows the entire elution pattern for the multi group
using hexane–dichloromethane (50:5) as solvent. isolation of PBDEs, PCBs, PCDDs and PCDFs.
The elution pattern is presented in Fig. 2. If for PCDD/F and PCB analysis, each congener
It shows that, under these conditions, alumina was can be quantified with its corresponding mass-la-
not able to provide a good separation between the belled compound, PBDE congener quantification has
different analytes. Only carbon appeared to be suited to be performed using the few commercially avail-
for the partition between planar and non-planar able labelled compounds. Since the internal standard
compounds. The use of carbon column however solution contains only some of the congeners, a
confronted us with a problem. While c-PCBs were single labelled compound quantified several con-
strongly retained on carbon column, some other geners with the same degree of bromination. For the
PCBs, mainly mono-ortho congeners, passed through present method, this generated difficulties in the
this column but were significantly slowed down. analysis of PBDEs which were not collected in the
Large quantities of solvent were thus required to same fraction as the labelled compound used for
collect them quantitatively, resulting in high LOQ their quantification. This was the case for some
values, as reported in our previous PCB determi- tetraBDEs (-49, -66, -75 and -77) and some penta-
nation study. BDEs (-116, -105 and -126). Measurement of these
The only way to avoid the use of such quantities were therefore performed using the tribrominated
of solvent was to modify the sequence of events such
as the PCBs would be isolated prior the carbon
column. An adequate solvent mixture was therefore
needed to selectively desorb PCBs from alumina
without affecting dioxins. Due to the high selectivity
of analytical method, PCBs and PBDEs did not have
Fig. 2. Percentage of recovery for PCBs (with a distinction
between planar and non-planar congeners), PBDEs, PCDDs and
PCDFs when hexane–dichloromethane (50:50) is used to elute the Fig. 3. Scheme of fraction collections for the automated clean-up
alumina column (PBDEs which were not eluted with this mixture and multi-group fractionation using multi-layer silica, basic
of solvent were not taken into account). alumina and PX-21 carbon disposable columns.
10. 178 C. Pirard et al. / J. Chromatogr. A 998 (2003) 169–181
Table 4
Multi-group fractionation and recovery (%) for the 65 target analytes
Congener 80:20 50:50 DCM Toluene Recovery Congener 80:20 50:50 DCM Toluene Recovery
(F2) (F3) (F4) (F6) (%) (F2) (F3) (F4) (F6) (%)
PBDEs PCBs
DiBDEs Non-ortho
10 x 40 TCB-77 x 81
7 x 49 TCB-81 x 85
11 x 92 PeCB-126 x 57
8 x 89 HxCB-169 x 53
13–12 x 75 Mono-ortho
15 x 91 PeCB-123 x 100
TriBDEs PeCB-118 x 104
30 x 47 PeCB-114 x 108
32 x 72 PeCB-105 x 57
17–25 x 88 HxCB-167 x 101
28–33 x 67 HxCB-156 x 102
35 x x 59 HxCB-157 x 98
37 x x 56 HpCB-189 x 66
TBDEs Aroclor 1260
75 x 72 TriCB-28 x 65
71 x 60 TCB-52 x 65
49 x 59 PeCB-101 x 97
47 x 79 HxCB-153 x 63
66 x 58 HxCB-138 x 94
77 x 93 HpCB-180 x 81
PeBDEs PCDD/Fs
100 x 66 2,3,7,8-TCDD x 88
119 x 59 1,2,3,7,8-PeCDD x 88
99 x 77 1,2,3,4,7,8-HxCDD x 60
116 x 60 1,2,3,6,7,8-HxCDD x 62
85 x 62 1,2,3,7,8,9-HxCDD x 70
126 x 92 1,2,3,4,6,7,8-HpCDD x 86
105 x 91 OCDD x 84
HxBDEs 2,3,7,8-TCDF x 88
154 x 77 1,2,3,7,8-PeCDF x 84
153 x 62 2,3,4,7,8-PeCDF x 82
140 x 61 1,2,3,4,7,8-HxCDF x 61
138 x 67 1,2,3,6,7,8-HxCDF x 65
166 x 64 1,2,3,7,8,9-HxCDF x 67
2,3,4,6,7,8-HxCDF x 64
1,2,3,4,6,7,8-HpCDF x 84
1,2,3,4,7,8,9-HpCDF x 100
OCDF x 79
13
[ C ]PBDE-28 (with adequate RRF). However, present in the blank procedural method were calcu-
12
this resulted in a loss of accuracy for quantification lated as the average blank value plus three times the
of these congeners. This was the price to pay for standard deviation (SD) of the blank. LOQs were
LOQ reduction for PCB analysis. defined as the average blank value plus 10 times the
SD. For congeners not found in blank, the LOD was
3.4. Evaluation of the whole procedure the values determined for sensitivity of the mass
spectrometer, that is values of smaller added con-
3.4.1. LODs and LOQs centration giving a signal with a signal-to-noise ratio
LODs and LOQs were evaluated using average (S/N) greater than 3. Table 5 shows LODs and
method blank values. LOD values for congeners LOQs for the few congeners found in procedural
11. C. Pirard et al. / J. Chromatogr. A 998 (2003) 169–181 179
Table 5 in triplicate. Mean levels obtained are gathered in
LODs and LOQs for congeners found in method procedural
Table 6. In the absence of a certified reference
blanks (n55) with the previous reported clean-up and with the
material, accuracy was estimated regarding values
new strategy
measured in the samples towards these expected
Congener Old strategy New strategy
following spike levels. Repeatability of the proce-
LOD LOQ LOD LOQ dure was tested by calculating the RSD between the
three analyses.
DiBDE-10 – – 6 17
TriBDE-35 – – 5 13 Accuracy ranged between 91 and 122% for
TBDE-47 – – 64 123 PBDEs excepted for PBDE-32 with a very high
PeBDE-99 – – 39 69
value of 140%. Results for most of the pentabromi-
HxBDE-154 – – 8 25
nated congeners were not reported due to very
HxBDE-153 – – 17 50
incoherent values, with accuracies ranging between
TriCB-28 16.31 34.03 2.38 6.01
TCB-52 14.90 32.61 1.78 4.00 25 and 75% and RSDs reaching sometimes up to
PeCB-101 8.60 18.47 0.83 1.98 96%. These incoherences were probably the result of
PeCB-118 2.80 5.78 0.16 0.30
the fractionation trouble mentioned above and the
HxCB-153 4.52 9.47 0.25 0.44
lack of an appropriate internal standard. Accuracy
PeCB-105 1.18 2.68 0.03 0.06
for PCB and PCDD/F determination was fairly
HxCB-138 7.66 17.95 0.41 0.72
HxCB-156 0.40 0.98 0.02 0.06 good, keeping in mind that samples were laboratory-
HpCB-180 1.95 4.66 0.22 0.63 made fortified fat and not certified reference materi-
HpCB-189 2.36 6.56 2.73 8.20
als. Acceptable repeatability was observed with
Data are expressed in pg/g of fat for PBDEs and ng/g of fat for RSDs being lower than 20% for all compounds
PCBs.
except for TBDE-77 and TCDD for which values
were slightly higher. PBDE-28, -47, -66, -99, -100,
blanks. Several studies have observed significant -153, -154, which are the congeners that were found
amount of PBDEs in laboratory blanks [27,33,34], most predominantly in abiotic or biological samples
predominantly PBDE-47 and PBDE-99, and more [1,2,11], i.e., are usually monitored in epidemiologi-
occasionally PBDE-100, PBDE-153 and PBDE-154. cal studies, such as in breast milk [4,30,35], blood
Similar trends were observed for our method blanks, [36] or fish [28,37]. They thus require special
even after implementation of actions to minimise attention during the analytical procedure. As shown
laboratory contamination, such as regular silanisation in Table 6, this method produced really reliable
of the few pieces of glassware used. results for these particular compounds, with ac-
Table 5 also shows LODs and LOQs for PCBs curacies ranging from 97 to 112% and SDs below
with this new strategy compared to the previous one. 10%.
The limits of detection and quantification obtained
with this extended clean-up are between 5 and 10-
times lower than in our previous study. They are 4. Conclusion
now widely below the norm imposed by BELTEST,
the Belgian accreditation body, which fixed LODs This simple, time- and resource-saving strategy
and LOQs at, respectively, 5 ng/g and 10 ng/g for allows to one incorporate analysis of a broad range
each congener of the Aroclor 1260. LOQs for PBDE of PBDEs with classical dioxin and PCB analysis.
congeners are definitely lower than level usually Purification and isolation of 25 PBDEs, from di- to
found in the environment, which used to range from hexabrominated congeners, the 12 non- and mono-
0.5 ng/g fat in Swedish human breast milk (for ortho PCBs, the seven congeners of Arolcor 1260,
PBDE-100) to up than 5000 ng/g fat in marine the 17 PCDDs and PCDFs are performed with a
mammals [2]. single and automated clean-up, while final determi-
nations are carried out on a single GC ion trap mass
3.4.2. Repeatability and accuracy spectrometer, in four separate injections.
In order to evaluate our method, QC samples were The combination of EI and tandem in time mass
purified and analysed using our multi-analyte method spectrometry offers the accuracy of EI-HRMS, in
12. 180 C. Pirard et al. / J. Chromatogr. A 998 (2003) 169–181
Table 6
Congener-specific data in pg/g fat for the laboratory-made quality control (n53)
Congener Levels in QC RSD Accuracy Congener Levels in QC RSD Accuracy
(pg/g fat) (%) (%) (pg/g fat) (%) (%)
PBDEs Aroclor 1260
DiBDE-10 121 15 121 TriCB-28 2117 6 96
DiBDE-7 101 11 101 TCB-52 2654 8 121
DiBDE-11 108 20 108 PeCB-101 2127 4 97
DiBDE-8 113 7 113 HxCB-153 2039 8 93
DiBDE-13&12 107 7 107 HxCB-138 2432 4 111
DiBDE-15 94 3 94 HpCB-180 2771 1 104
TriBDE-30 94 15 94 c-PCBs
TriBDE-32 140 13 140 TCB-77 11.3 15 113
TriBDE-17&25 105 2 105 TCB-81 10.6 11 106
TriBDE-28&33 97 10 97 PeCB-126 63.4 4 127
TriBDE-35 122 7 122 HxCB-169 107.1 1 107
TriBDE-37 118 1 118 Dioxins
TBDE-75 103 3 103 PCDDs
TBDE-71 112 12 112 2,3,7,8-TCDD 0.41 29 103
TBDE-49 99 6 99 1,2,3,7,8-PeCDD 1.92 17 96
TBDE-47 112 10 112 1,2,3,4,7,8-HxCDD 1.83 7 92
TBDE-66 112 1 112 1,2,3,6,7,8-HxCDD 2.22 14 111
TBDE-77 119 27 119 1,2,3,7,8,9-HxCDD 1.81 2 90
PeBDE-100 147 3 98 1,2,3,4,6,7,8-HpCDD 2.28 19 114
PeBDE-99 148 20 98 OCDD 4.20 15 105
PeBDE-116 137 6 91 PCDFs
HxBDE-154 211 8 106 2,3,7,8-TCDF 0.42 18 105
HxBDE-153 213 12 106 1,2,3,7,8-PeCDF 2.60 4 130
HxBDE-140 205 15 102 2,3,4,7,8-PeCDF 2.26 12 113
HxBDE-138 209 6 104 1,2,3,4,7,8-HxCDF 1.96 19 98
PCBs 1,2,3,6,7,8-HxCDF 1.95 8 98
Mono-ortho 1,2,3,7,8,9-HxCDF 2.26 3 113
PeCB-123 325 1 81 2,3,4,6,7,8-HxCDF 1.87 8 94
PeCB-118 2079 4 95 1,2,3,4,6,7,8-HpCDF 2.55 7 128
PeCB-114 396 7 99 1,2,3,4,7,8,9-HpCDF 2.25 10 112
PeCB-105 451 2 113 OCDF 4.17 7 104
HxCB-167 364 5 91
HxCB-156 362 0 90
HxCB-157 465 5 116
HpCB-189 80 19 90
allowing the quantification by isotopic dilution, and whole method has been demonstrated to be robust,
even a higher degree of selectivity achieving to repeatable and fairly accurate, producing good re-
separate isobaric ions such as PBDE-47 and PCB- covery rates, especially for PBDE-28, -47, -66, -99,
180 which were not resolved under normal operating -100, -153 and -154 which are the most relevant
conditions with HRMS. On the other hand, MS–MS congeners. Limits of detection and quantification for
has advantages of NCI-LRMS in being a user-friend- PCB analysis were drastically reduced compared to
ly and low-cost instrument. Working in tandem mass our previous study and are now widely below the
spectrometry increases sensitivity and offsets the use values fixed by accreditation body.
of EI as ionization mode, nearly competing with This method could be easily extended to biological
NCI-LRMS for limits of detection. Spectrometer fluids such as milk and serum using automated on-
response has proven to be repeatable, reproducible line (integrated) solid-phase extraction which was
and linear in the studied concentration range. The already optimised in our laboratory [38]. This will
13. C. Pirard et al. / J. Chromatogr. A 998 (2003) 169–181 181
´
[18] P.O. Darnerud, G.S. Eriksen, T. Johannesson, P.B. Larsen,
allow one to make epidemiological studies on a wide
M. Viluksela, Environ. Health Perspect. 109 (2001) 49.
range of compounds more efficiently.
[19] J. de Boer, P. Korytar, in: Proceedings of the 2nd Internation-
al Workshop on Brominated Flame Retardants, Stockholm,
2001, p. 45.
Acknowledgements [20] K. Ballschmiter, M. Zell, Fresenius Z. Anal. Chem. 302
(1980) 20.
[21] J.-F. Focant, G. Eppe, C. Pirard, E. De Pauw, J. Chromatogr.
The authors thank FMS for their collaboration and
A 925 (2001) 207.
`
University of Liege for both financial and technical [22] C. Pirard, J.-F. Focant, E. De Pauw, Anal. Bioanal. Chem.
support. 372 (2002) 373.
[23] W.E. Turner, T.P. Cash, E.S. DiPietro, D.G. Patterson Jr.,
Organohalogen Comp. 35 (1998) 21.
´
[24] E. Abad, J. Saulo, J. Caixach, J. Rivera, J. Chromatogr. A
References
893 (2000) 3830.
[25] J.-F. Focant, G. Eppe, E. De Pauw, Organohalogen Comp.
[1] WHO, in: Brominated Diphenyl Ether, ICPS Environmental 45 (2000) 49.
Health Criteria, World Health Organization, Geneva, 1994, p. [26] D.L. Stalling, R. Tindle, J.L. Johnson, J. Assoc. Off. Anal.
162. Chem. 55 (1972) 32.
[2] C.A. de Wit, Chemosphere 46 (2002) 583. [27] J.K. Huwe, M. Lorentzsen, K. Thuresson, A. Bergman,
[3] I. Andersson, G. Blomkvist, Chemosphere 10 (1981) 1051. Chemosphere 46 (2002) 635.
´ ´
[4] K. Noren, D. Meyronte, Chemosphere 40 (2000) 1111. [28] M. Alaee, D.B. Sergeant, M. Ikonomou, J.M. Luross,
`
[5] B. Jansson, R. Andersson, L. Asplund, K. Litzen, K. Nylund, Chemosphere 44 (2001) 1489.
¨
U. Sellstrom, U.-B. Uvemo, C. Wahlberg, U. Wideqvist, T. [29] P.S. Haglund, D.R. Zook, H.-R. Buser, J. Hu, Environ. Sci.
¨
Odsjo, M. Olsson, Environ. Toxicol. Chem. 12 (1993) 1163. Technol. 31 (1997) 3281.
[6] J. de Boer, K. de Boer, J.P. Boon, in: The Handbook of ´ ´
[30] D. Meyronte, A. Bergman, K. Noren, J. Toxicol. Environ.
Environmental Chemistry, Springer, Berlin, Heidelberg, Health A 58 (1999) 329.
2000, p. 61. [31] J. Luross, D.B. Sergeant, M. Alaee, Organohalogen Comp.
[7] J. de Boer, Chemosphere 18 (1989) 2131. 40 (1999) 9.
[8] M.G. Ikonomou, M. Fischer, T. He, R.F. Addison, T. Smith, [32] G. Marsh, J. Hu, E. Jakobsson, S. Rahm, A. Bergman,
Organohalogen Comp. 47 (2000) 77. Environ. Sci. Technol. 33 (1999) 3033.
[9] L. Watanabe, T. Kashimoto, R. Tatsukawa, Chemosphere 16 [33] C. Thomsen, H. Leknes, E. Lundanes, G. Becher, J. Chroma-
(1987) 2389. togr. A 923 (2001) 299.
[10] J. de Boer, J. Chromatogr. A 843 (1999) 179. [34] J.J. Ryan, B. Patry, in: Proceedings of the 2nd International
[11] F. Rahman, K.H. Langford, M.D. Scrimshaw, J.N. Lester, Workshop on Brominated Flame Retardants, Stockholm,
Sci. Totol Environ. 275 (2001) 1. 2001, p. 103.
[12] A. Covaci, J. de Boer, J.J. Ryan, S. Voorspoels, P. Schepens, [35] P.O. Darnerud, S. Atuma, M. Aune, S. Cnattingius, M.L.
Anal. Chem. 74 (2001) 790. Wernroth, A. Wicklund-Glynn, Organohalogen Comp. 35
[13] C. Thomsen, L. Smastuen haug, H. Leknes, E. Lundanes, G. (1998) 411.
¨
Becher, G. Lindstrom, Chemosphere 46 (2002) 641. [36] C. Thomsen, E. Lundanes, G. Becher, Environ. Sci. Technol.
[14] M. Alaee, in: R. Clement, B. Burk (Eds.), Proceedings of the 36 (2002) 1414.
4th Biennal International Conference on Monitoring and [37] K. Akutsu, H. Obana, M. Okihashi, M. Kitagawa, H.
Measurement of the Environment, Toronto, 2002, p. 309. Nakazawa, Y. Matsuki, T. Makino, H. Oda, S. Hori, Chemo-
[15] E. Eljarrat, S. Lacorte, D. Barcelo, J. Mass Spectrom. 37 sphere 44 (2001) 1325.
(2002) 76. [38] J.F. Focant, E. De Pauw, J. Chromatogr. B 776 (2002) 199.
[16] J.-F. Focant, G. Eppe, E. De Pauw, Chemosphere 43 (2001)
417.
[17] G. Eppe, J.F. Focant, C. Pirard, E. De Pauw, Organohalogen
Comp. 50 (2001) 186.