1) The document provides instructions for operating the TX10 MedServer all-in-one computer cart, including how to power on/off the computer and cart, charge the battery, lock and unlock the cart, adjust the height, and clean the unit. 2) Troubleshooting tips are given for issues like the computer not powering on, keyboard or mouse not working, difficulty moving the cart, drawers not locking or opening, and low battery charges. 3) Contact information and the website are provided for additional support.

1. Quick Start User Guide
TX10 MedServer All-in-One
Computer Power On / Off
• ON: Press ON/OFF button on monitor for
approximately 2-3 seconds.
• OFF: Use standard operating system Log
Off/Shut Down procedures.
If the computer does not power-up, be certain battery is
charged to sufficient level (>20%). If not, please be certain
to immediately recharge unit.
Cart On / Off
Position switch in the ON or OFF position (located on lower / back
portion of cart). ON position for normal operation and function
of computer and lock system. OFF position for storage to protect battery life.
Battery Charge / Recharging
• Plug the cart into an outlet. LCD display will read “ CHARGING ” to confirm cart is
charging.
• To check battery charge level, press the button on the keypad. The cart must be unplugged
to check the battery charge level.
To ensure ample power for continuous and uninterrupted use, please plug cart into outlet during any period
when the unit is not in use. BE SURE TO UNPLUG CART BEFORE MOVING AWAY FROM OUTLET.
Unlocking the Cart During Medication Pass
1. Press the button on keypad to ‘wake-up’ the keyless lock system.
2. LCD will display “ENTER ACCESS CODE”. Enter the valid 4-digit access code. If you make a mistake while
entering your code, press the button to delete the incorrect digit(s), and re-enter correct code.
3. Cart will open and provide access to patient bins and drawers.
Securing the Cart During Medication Pass
1. Close all patient bins and drawers.
2. Press the button on the keypad.
3. Once the cart is secure, the LCD will display “CART SECURED”.
4. If the cart remains motionless while unlocked, the auto-relock will engage.
5. If the cart has relocked, simply enter a valid 4-digit access code to access cart.
Height Adjustment
To adjust the vertical height of the work surface or computer monitor, perform the following:
• To raise the unit, press the button on the keypad.
• To lower the unit, press the button on the keypad.

2. Wheel Locks
• To keep the unit stationary while in use, push down the Wheel Lock Off Lock On
Lock Tabs located on the unit’s casters. To unlock, lift the Wheel
Lock Tab to the upward position.
If you are having difficulty pushing or maneuvering the unit, be certain
the Wheel Lock Tabs are NOT in the down or locked position. Be
certaiN cart is NOt Plugged-iN tO wall Outlet.
QuickClear Button
• To temporarily ‘hide’ screen data to protect privacy, simply press the
button on the monitor. To restore monitor image, press button again.
Product Maneuvering
• Only use the integrated work surface handle when moving the cart unit. DO NOT attempt to
push, pull or lift cart unit by the keyboard tray or monitor mount column. When crossing a flooring
threshold, Artromick suggests PulliNg the cart over the threshold to ensure a safe and stable
transition.
Cleaning Unit
• Apply cleaning agent (isopropyl alcohol, warm soapy water, non-corrosive or non-abrasive agents) to
a soft cloth and wipe surfaces as needed. Thoroughly dry.
• DO NOT apply cleaning agents, whether aerosol or liquid-based, directly to any surface of the
computing unit of cart.
Troubleshooting Guide
Computer does not have power / monitor is not working
confirm the QuickClear button has not been pressed.
confirm the computer has not entered stand-by or hibernation mode.
check that the unit is sufficiently charged. Press button on keypad to confirm system has
ample charge to power the computer. Charge must be greater than 20% for computer to function. If
less than 20%, plug battery system power cord into outlet until sufficient charge is supplied to system.
confirm all the cable connections into the bottom of the computer monitor are fully plugged-in
and secure.
Keyboard keys and /or mouse are not working
check that the external USB plug is fully inserted into the monitor unit.
Moving Cart is Difficult
check to be sure cart unit wheels are NOT in the locked position (lock tab pressed down).
check to be sure cart unit is NOT plugged into wall outlet and recharging.
Cart Drawers Will Not Lock
confirm the lock system is in the secure position by pressing the SECURE key on the keypad.
confirm there are no items protruding from drawers or bins that may prohibit full closure.
Cart Drawers Will Not Open
If the bins or drawers will not open after entering the 4-digit access code, confirm the user access
code is valid.
If the cart still does not open, press the button. Battery charge must be greater than 20%.
If the cart does not have sufficient charge to use the keypad for access, use the override cart key
located on the back of the unit to open drawers. Begin charging immediately.
www.artromick.com © Artromick International, Inc., 2006 Re.v. 6/07
800 848 6462 Form A-124 P/N 6840