LINDAPTER Girder-Clamp connections are used to connect steel without welding or drilling. These connections allow for faster and safer installation, simplifying the construction process. LINDAPTER provides a free design service. For more information email me at mcardenas@lindapter.com or visit www.lindapterusa.com

1. A
W12x26
W6x15
5
8"
11
16 " THRU
11"
6
11
16"
7
3
16 "
11
1
2 "
DETAIL A
SCALE 1 : 3
End Plate, 50ksi Material
Lindapter LAAF062 Clamp
Ø5/8" x 6" Long Bolt (Grade A490)
with Nut & Nord-Lock Washer
Lindapter LAAF062 Clamp
For combined loadings the current relevant national
standard should be taken into consideration
Note:
Drawing to be read in
conjunction with supporting
spreadsheet
Assembly Data:
Static Tensile SWL = 17532 lbs
Factor of Safety :
4.5 : 1
Static Slip Resistance
SWL =
4946 lbs
Factor of Safety :
2 : 1
Lindapter Fastener
Tightening Torque =
221 ft-lb
DWG. NO. REV.
CHECKEDDATE
WEIGHT:
DESCRIPTIONREV. DATEBY
0SW7724-AR
A.R. 28-APR-2015
GC001-8
W6x15 to W12x26
Connection Details
CUSTOMER
GB-06136
ENQUIRY N.
SCALE:
www.lindapterusa.com
OFFICIAL LINDAPTER DISTRIBUTOR:
sales@all-profasteners.comwww.all-profasteners.com
817-467-5700
DRAWN
DRAWING TITLE
M.K.
NOT TO SCALE
A C C E P T N O S U B S T I T U T E
PROJECT
DRAWING NOTES:
GENERAL NOTES:
DIMENSIONS ARE IN INCHES1.
TOLERANCES:2.
ANGULAR: BEND3.
MATERIAL COATINGS TO BE SPECIFIED BY THE ENGINEER4.
DO NOT SCALE THIS DRAWING1.
THIS DRAWING AND THE COPYRIGHT THEREIN ARE THE2.
PROPERTY OF LINDAPTER INTERNATIONAL. IT IS ISSUED ON
THE CONDITION THAT IT MUST NOT BE USED, COPIED,
DISTRIBUTED OR EXHIBITED WITHOUT WRITTEN PERMISSION
AND CONSENT. THE DRAWING MUST ALSO NOT BE USED
FOR ANY OTHER PURPOSE THAN WHICH IT IS ISSUED.
IT IS THE RESPONSIBILITY OF THE ENGINEER TO PERFORM3.
ALL REASONABLE CHECKS ON THE SUPPORTING AND
SUPPORTED MEMBERS. THAT IS LOCAL TO THE
CONNECTION AND THE LINDAPTER COMPONENTS, BOTH
FOR THE LOAD APPLIED AND THE CLAMPING FORCE
GENERATED FROM THE TIGHTENING OF THE FASTENERS.
IF FELT NECESSARY, WHERE EXCESSIVE VIBRATION MAY BE4.
A CONCERN, IT IS ACCEPTABLE FOR CERTAIN TYPES OF
ANTI-VIBRATION LOCKING DEVICES SUCH AS, BUT NOT
LIMITED TO, PROPRIETARY WASHERS AND NUTS TO BE
USED WITH LINDAPTER COMPONENTS AND/OR
ASSEMBLIES; SPRING WASHERS OF ANY TYPE ARE NOT
RECOMMENDED. IN THESE SITUATIONS IT IS IMPORTANT
THAT THE MANUFACTURER'S INSTALLATION INSTRUCTIONS
ARE FOLLOWED. NO GUARANTEES OR WARRANTIES ARE
IMPLIED.

2. A
Existing W Beam
Flange Width Range = 4" to 14-1/2"
Flange Thickness Range = 1/4" to 1-3/16"
3
4"
11"
7"
20"
15
1
4 "
4
11
16 "
11
16 " X 5
31
32 "
DETAIL A
SCALE 1 : 3
End Plate, 50ksi Material
Lindapter LAAF062 Clamp
Ø5/8" Fully Threaded Bolt (Grade 5/A325)
with Nut & 2x Nord-Lock Washers
For combined loadings the current relevant national
standard should be taken into consideration
Note:
Drawing to be read in
conjunction with supporting
spreadsheet
Assembly Data:
Static Tensile SWL = 14388 lbs
Factor of Safety :
4.5 : 1
Static Slip Resistance
SWL =
3596 lbs
Factor of Safety :
2 : 1
Lindapter Fastener
Tightening Torque =
177 ft-lb
DWG. NO. REV.
CHECKEDDATE
WEIGHT:
DESCRIPTIONREV. DATEBY
ASW7963-AR
A.R. 17-JUN-2015
LAAF062 Clamp to
Existing W Beam
Typical Details
CUSTOMER
GB-06373
ENQUIRY N.
SCALE:
www.lindapterusa.com
OFFICIAL LINDAPTER DISTRIBUTOR:
sales@all-profasteners.comwww.all-profasteners.com
817-467-5700
DRAWN
DRAWING TITLE
S.C.
NOT TO SCALE
A C C E P T N O S U B S T I T U T E
PROJECT
DRAWING NOTES:
GENERAL NOTES:
DIMENSIONS ARE IN INCHES1.
TOLERANCES:2.
ANGULAR: BEND3.
MATERIAL COATINGS TO BE SPECIFIED BY THE ENGINEER4.
DO NOT SCALE THIS DRAWING1.
THIS DRAWING AND THE COPYRIGHT THEREIN ARE THE2.
PROPERTY OF LINDAPTER INTERNATIONAL. IT IS ISSUED ON
THE CONDITION THAT IT MUST NOT BE USED, COPIED,
DISTRIBUTED OR EXHIBITED WITHOUT WRITTEN PERMISSION
AND CONSENT. THE DRAWING MUST ALSO NOT BE USED
FOR ANY OTHER PURPOSE THAN WHICH IT IS ISSUED.
IT IS THE RESPONSIBILITY OF THE ENGINEER TO PERFORM3.
ALL REASONABLE CHECKS ON THE SUPPORTING AND
SUPPORTED MEMBERS. THAT IS LOCAL TO THE
CONNECTION AND THE LINDAPTER COMPONENTS, BOTH
FOR THE LOAD APPLIED AND THE CLAMPING FORCE
GENERATED FROM THE TIGHTENING OF THE FASTENERS.
IF FELT NECESSARY, WHERE EXCESSIVE VIBRATION MAY BE4.
A CONCERN, IT IS ACCEPTABLE FOR CERTAIN TYPES OF
ANTI-VIBRATION LOCKING DEVICES SUCH AS, BUT NOT
LIMITED TO, PROPRIETARY WASHERS AND NUTS TO BE
USED WITH LINDAPTER COMPONENTS AND/OR
ASSEMBLIES; SPRING WASHERS OF ANY TYPE ARE NOT
RECOMMENDED. IN THESE SITUATIONS IT IS IMPORTANT
THAT THE MANUFACTURER'S INSTALLATION INSTRUCTIONS
ARE FOLLOWED. NO GUARANTEES OR WARRANTIES ARE
IMPLIED.
A AR 30-JUL-2015INCREASED SLOT LENGTH IN PLATE

3. 5
3
4 "
0.36
8
7
8"
A
W16x89
(Can be Spliced at this Location)
1"
1"
10.37
7
8"
W10x22
13
16 " THRU
12"
16
1
2"
6
9
16 "
11
3
16"
DETAIL A
SCALE 1 : 5
Ø3/4" x 17-1/2" Fully Threaded Rod
to ASTM A449 with 4x Nuts & Washers
Lindapter LAAF075 Clamp
Location Plate, 50ksi Plate
Location Plate, 50ksi Plate
Lindapter LAAF075 Clamp
CONNECTION NOT SUITABLE FOR
HORIZONTAL OR COMPRESSION LOADS
Assembly Data:
Static Tensile SWL = 11802 lbs
Factor of Safety :
4.5 : 1
Lindapter Fastener
Tightening Torque =
347 ft-lb
DWG. NO. REV.
CHECKEDDATE
WEIGHT:
DESCRIPTIONREV. DATEBY
0SW8828-AR
A.R. 05-JAN-2016
W16x89 to W10x22
Connection Details
CUSTOMER
GB-06915
ENQUIRY N.
SCALE:
www.lindapterusa.com
OFFICIAL LINDAPTER DISTRIBUTOR:
sales@all-profasteners.comwww.all-profasteners.com
817-467-5700
DRAWN
DRAWING TITLE
I.P.
NOT TO SCALE
A C C E P T N O S U B S T I T U T E
PROJECT
DRAWING NOTES:
GENERAL NOTES:
DIMENSIONS ARE IN INCHES1.
TOLERANCES:2.
ANGULAR: BEND3.
MATERIAL COATINGS TO BE SPECIFIED BY THE ENGINEER4.
DO NOT SCALE THIS DRAWING1.
THIS DRAWING AND THE COPYRIGHT THEREIN ARE THE2.
PROPERTY OF LINDAPTER INTERNATIONAL. IT IS ISSUED ON
THE CONDITION THAT IT MUST NOT BE USED, COPIED,
DISTRIBUTED OR EXHIBITED WITHOUT WRITTEN PERMISSION
AND CONSENT. THE DRAWING MUST ALSO NOT BE USED
FOR ANY OTHER PURPOSE THAN WHICH IT IS ISSUED.
IT IS THE RESPONSIBILITY OF THE ENGINEER TO PERFORM3.
ALL REASONABLE CHECKS ON THE SUPPORTING AND
SUPPORTED MEMBERS. THAT IS LOCAL TO THE
CONNECTION AND THE LINDAPTER COMPONENTS, BOTH
FOR THE LOAD APPLIED AND THE CLAMPING FORCE
GENERATED FROM THE TIGHTENING OF THE FASTENERS.
IF FELT NECESSARY, WHERE EXCESSIVE VIBRATION MAY BE4.
A CONCERN, IT IS ACCEPTABLE FOR CERTAIN TYPES OF
ANTI-VIBRATION LOCKING DEVICES SUCH AS, BUT NOT
LIMITED TO, PROPRIETARY WASHERS AND NUTS TO BE
USED WITH LINDAPTER COMPONENTS AND/OR
ASSEMBLIES; SPRING WASHERS OF ANY TYPE ARE NOT
RECOMMENDED. IN THESE SITUATIONS IT IS IMPORTANT
THAT THE MANUFACTURER'S INSTALLATION INSTRUCTIONS
ARE FOLLOWED. NO GUARANTEES OR WARRANTIES ARE
IMPLIED.

4. 9.02
0.77
3.23
A
Lifting Ring
11.79
16"
32"
DETAIL A
SCALE 1 : 3
Ø1" x 5-1/2" Long Grade A490
Bolt with Nut & Washer
Lindapter LAF100S Clamp
with LAF100W Washer in Recess
Location Plate
Lindapter LAF100P1 Packer
Lifting Point Data:
Static Lifting SWL =
10 tonne
(100 kN)
Factor of Safety :
2 : 1
Safe Lifting Angle = 0-90° about 360° of rotation
Lindapter Fastener
Tightening Torque =
737 ft-lb
DWG. NO. REV.
CHECKEDDATE
WEIGHT:
DESCRIPTIONREV. DATEBY
0SW8424-AR
A.R. 30-SEP-2015
10 Tonne LP8
Lifting Point to a
W24x84 Beam
CUSTOMER
GB-06898
ENQUIRY N.
SCALE:
www.lindapterusa.com
OFFICIAL LINDAPTER DISTRIBUTOR:
DRAWN
DRAWING TITLE
GENERAL NOTES:
I.P.
NOT TO SCALE
A C C E P T N O S U B S T I T U T E
DRAWING NOTES:
PROJECT
DIMENSIONS ARE IN INCHES1.
TOLERANCES:2.
ANGULAR: BEND3.
MATERIAL COATINGS TO BE SPECIFIED BY THE ENGINEER4.
DO NOT SCALE THIS DRAWING1.
THIS DRAWING AND THE COPYRIGHT THEREIN ARE THE2.
PROPERTY OF LINDAPTER INTERNATIONAL. IT IS ISSUED ON
THE CONDITION THAT IT MUST NOT BE USED, COPIED,
DISTRIBUTED OR EXHIBITED WITHOUT WRITTEN PERMISSION
AND CONSENT. THE DRAWING MUST ALSO NOT BE USED
FOR ANY OTHER PURPOSE THAN WHICH IT IS ISSUED.
IT IS THE RESPONSIBILITY OF THE ENGINEER TO PERFORM3.
ALL REASONABLE CHECKS ON THE SUPPORTING AND
SUPPORTED MEMBERS. THAT IS LOCAL TO THE
CONNECTION AND THE LINDAPTER COMPONENTS, BOTH
FOR THE LOAD APPLIED AND THE CLAMPING FORCE
GENERATED FROM THE TIGHTENING OF THE FASTENERS.
IF FELT NECESSARY, WHERE EXCESSIVE VIBRATION MAY BE4.
A CONCERN, IT IS ACCEPTABLE FOR CERTAIN TYPES OF
ANTI-VIBRATION LOCKING DEVICES SUCH AS, BUT NOT
LIMITED TO, PROPRIETARY WASHERS AND NUTS TO BE
USED WITH LINDAPTER COMPONENTS AND/OR
ASSEMBLIES; SPRING WASHERS OF ANY TYPE ARE NOT
RECOMMENDED. IN THESE SITUATIONS IT IS IMPORTANT
THAT THE MANUFACTURER'S INSTALLATION INSTRUCTIONS
ARE FOLLOWED. NO GUARANTEES OR WARRANTIES ARE
IMPLIED.
817-467-5700
www.all-profasteners.com sales@all-profasteners.com

5. 1
1
4 "
Pipe Shoe (by others)
L3x3x1/2"
(Hot Dip Galvanised)
Beam
(Flange Width can vary from 4" to 8-1/8")
(Flange Thickness can vary from 0.196" to 1.024")
A
4
1
2"
8
5
8"
12"
9
16 "
DETAIL A
SCALE 1 : 2
Lindapter LAAF050 Clamp (HDG as Standard)
Ø1/2" x 3-1/2" Long Fully Threaded
A325 Bolt with Washer & Nut
(Double Nuts if Customer Wishes)
(All Hot Dip Galvanised)
For combined loadings the current relevant national
standard should be taken into consideration
Assembly Data:
Static Tensile SWL = N/A
Static Slip Resistance
SWL =
1528 lbs
Factor of Safety :
2 : 1
Lindapter Fastener
Tightening Torque =
66 ft-lb
DWG. NO. REV.
CHECKEDDATE
WEIGHT:
DESCRIPTIONREV. DATEBY
0SW7526-AR
A.R. 16-MAR-2015
Pipe Support Detail
for Multiple Beams
CUSTOMER
GB-05920
ENQUIRY N.
SCALE:
www.lindapterusa.com
OFFICIAL LINDAPTER DISTRIBUTOR:
sales@all-profasteners.comwww.all-profasteners.com
817-467-5700
DRAWN
DRAWING TITLE
I.P.
NOT TO SCALE
A C C E P T N O S U B S T I T U T E
PROJECT
DRAWING NOTES:
GENERAL NOTES:
DIMENSIONS ARE IN INCHES1.
TOLERANCES:2.
ANGULAR: BEND3.
MATERIAL COATINGS TO BE SPECIFIED BY THE ENGINEER4.
DO NOT SCALE THIS DRAWING1.
THIS DRAWING AND THE COPYRIGHT THEREIN ARE THE2.
PROPERTY OF LINDAPTER INTERNATIONAL. IT IS ISSUED ON
THE CONDITION THAT IT MUST NOT BE USED, COPIED,
DISTRIBUTED OR EXHIBITED WITHOUT WRITTEN PERMISSION
AND CONSENT. THE DRAWING MUST ALSO NOT BE USED
FOR ANY OTHER PURPOSE THAN WHICH IT IS ISSUED.
IT IS THE RESPONSIBILITY OF THE ENGINEER TO PERFORM3.
ALL REASONABLE CHECKS ON THE SUPPORTING AND
SUPPORTED MEMBERS. THAT IS LOCAL TO THE
CONNECTION AND THE LINDAPTER COMPONENTS, BOTH
FOR THE LOAD APPLIED AND THE CLAMPING FORCE
GENERATED FROM THE TIGHTENING OF THE FASTENERS.
IF FELT NECESSARY, WHERE EXCESSIVE VIBRATION MAY BE4.
A CONCERN, IT IS ACCEPTABLE FOR CERTAIN TYPES OF
ANTI-VIBRATION LOCKING DEVICES SUCH AS, BUT NOT
LIMITED TO, PROPRIETARY WASHERS AND NUTS TO BE
USED WITH LINDAPTER COMPONENTS AND/OR
ASSEMBLIES; SPRING WASHERS OF ANY TYPE ARE NOT
RECOMMENDED. IN THESE SITUATIONS IT IS IMPORTANT
THAT THE MANUFACTURER'S INSTALLATION INSTRUCTIONS
ARE FOLLOWED. NO GUARANTEES OR WARRANTIES ARE
IMPLIED.

6. 1"
A
2-1/2" or 3" Pipe
Existing Truss Angle
6" x 6" x 1/2"
Location Plate
11
16 " THRU
8"
10"
5"
6
11
16"
Pipe Clamp
(by engineer)
DETAIL A
SCALE 2 : 5
Lindapter LCF062
Lindapter LAF062S
5/8" x 12" Fully-threaded
Rod with 3 Nuts & 3 Washers
5/8" x 5" Fully-threaded
Grade 5 Bolt with 2 Nuts &
2 Washers
Lindapter LAF062P1
Connection Data:
Tensile SWL = 14388 lbs
Friction SWL = 3596 lbs
Factor of Safety = 5 : 1
Tightening Torque = 177 ft lb
DWG. NO. REV.
CHECKEDDATE
WEIGHT:
DESCRIPTIONREV. DATEBY
0SW3716-AR
A.R. 22-OCT-2012
Pipe Fixing Detail to
Existing Truss Angle -
6" x 6" x 1/2"
CUSTOMER
GB-00471
ENQUIRY N.
SCALE:
www.lindapterusa.com
OFFICIAL LINDAPTER DISTRIBUTOR:
sales@all-profasteners.comwww.all-profasteners.com
817-467-5700
DRAWN
DRAWING TITLE
GENERAL NOTES:
NOT TO SCALE
A C C E P T N O S U B S T I T U T E
DO NOT SCALE THIS DRAWING1.
DIMENSIONS ARE IN INCHES2.
TOLERANCES:3.
ANGULAR: BEND4.
THIS DRAWING AND THE COPYRIGHT5.
THEREIN ARE THE PROPERTY OF LINDAPTER
INTERNATIONAL. IT IS ISSUED ON THE
CONDITION THAT IT MUST NOT BE USED,
COPIED, DISTRIBUTED OR EXHIBITED
WITHOUT WRITTEN PERMISSION AND
CONSENT. THE DRAWING MUST ALSO
NOT BE USED FOR ANY OTHER PURPOSE
THAN WHICH IT IS ISSUED.
DRAWING NOTES:
IT IS THE RESPONSIBILITY OF THE ENGINEER TO1.
PERFORM ALL REASONABLE CHECKS ON THE
SUPPORTING AND SUPPORTED MEMBERS.
THAT IS LOCAL TO THE CONNECTION AND
THE LINDAPTER COMPONENTS, BOTH FOR
THE LOAD APPLIED AND THE CLAMPING
FORCE GENERATED FROM THE TIGHTENING
OF THE FASTENERS.
PROJECT

7. 3
4"
5
1
2 "
0.35
A
W16x26 Beam
Ø3-1/2" Pipe Welded
to Capping Plate
13
16 " THRU
11"
11"
6
5
16 "
6
5
16"
DETAIL A
SCALE 1 : 2
Lindapter LAF075S Clamp
with LAF075W Washer in Recess
Ø3/4" x 3-3/4" Long Grade
A325 Bolt with Nut & Washer
For combined loadings the current relevant national
standard should be taken into consideration
Assembly Data:
Static Tensile SWL = 23604 lbs
Factor of Safety :
5 : 1
Static Slip Resistance
SWL =
5844 lbs
Factor of Safety :
2 : 1
Lindapter Fastener
Tightening Torque =
347 ft-lb
DWG. NO. REV.
CHECKEDDATE
WEIGHT:
DESCRIPTIONREV. DATEBY
0SW8292-AR
A.R. 03-SEP-2015
Assembly Type 2:
Hanger to W16x26
Using 3/4" Type AF
CUSTOMER
GB-06768
ENQUIRY N.
SCALE:
www.lindapterusa.com
OFFICIAL LINDAPTER DISTRIBUTOR:
sales@all-profasteners.comwww.all-profasteners.com
817-467-5700
DRAWN
DRAWING TITLE
I.P.
NOT TO SCALE
A C C E P T N O S U B S T I T U T E
PROJECT
DRAWING NOTES:
GENERAL NOTES:
DIMENSIONS ARE IN INCHES1.
TOLERANCES:2.
ANGULAR: BEND3.
MATERIAL COATINGS TO BE SPECIFIED BY THE ENGINEER4.
DO NOT SCALE THIS DRAWING1.
THIS DRAWING AND THE COPYRIGHT THEREIN ARE THE2.
PROPERTY OF LINDAPTER INTERNATIONAL. IT IS ISSUED ON
THE CONDITION THAT IT MUST NOT BE USED, COPIED,
DISTRIBUTED OR EXHIBITED WITHOUT WRITTEN PERMISSION
AND CONSENT. THE DRAWING MUST ALSO NOT BE USED
FOR ANY OTHER PURPOSE THAN WHICH IT IS ISSUED.
IT IS THE RESPONSIBILITY OF THE ENGINEER TO PERFORM3.
ALL REASONABLE CHECKS ON THE SUPPORTING AND
SUPPORTED MEMBERS. THAT IS LOCAL TO THE
CONNECTION AND THE LINDAPTER COMPONENTS, BOTH
FOR THE LOAD APPLIED AND THE CLAMPING FORCE
GENERATED FROM THE TIGHTENING OF THE FASTENERS.
IF FELT NECESSARY, WHERE EXCESSIVE VIBRATION MAY BE4.
A CONCERN, IT IS ACCEPTABLE FOR CERTAIN TYPES OF
ANTI-VIBRATION LOCKING DEVICES SUCH AS, BUT NOT
LIMITED TO, PROPRIETARY WASHERS AND NUTS TO BE
USED WITH LINDAPTER COMPONENTS AND/OR
ASSEMBLIES; SPRING WASHERS OF ANY TYPE ARE NOT
RECOMMENDED. IN THESE SITUATIONS IT IS IMPORTANT
THAT THE MANUFACTURER'S INSTALLATION INSTRUCTIONS
ARE FOLLOWED. NO GUARANTEES OR WARRANTIES ARE
IMPLIED.

8. 30
W250x58
Flange Width = 202.8mm
Flange Thickness = 13.5mm
HSS203x203x9.5
26 THRU
229
380
75.50
300
500
100
A
DETAIL A
SCALE 2 : 7.5
Lindapter LAF100S
with LAF100W Washer
1" x 5" Grade 5
Bolt with Nut & Washer
For combined loadings the current relevant national
standard should be taken into consideration
Assembly Data:
Static Tensile SWL = 160 kN
Factor of Safety :
5 : 1
Static Slip Resistance
SWL =
48 kN
Factor of Safety :
5 : 1
Lindapter Fastener
Tightening Torque =
800 Nm
DWG. NO. REV.
CHECKEDDATE
WEIGHT:
DESCRIPTIONREV. DATEBY
0SW5374-AR
A.R. 03-DEC-2013
HSS203x203x9.5 to
W250x58
Connection Details
CUSTOMER
GB-02215
ENQUIRY N.
SCALE:
www.lindapterusa.com
OFFICIAL LINDAPTER DISTRIBUTOR:
DRAWN
DRAWING TITLE
GENERAL NOTES:
I.P.
NOT TO SCALE
A C C E P T N O S U B S T I T U T E
DRAWING NOTES:
PROJECT
DIMENSIONS ARE IN INCHES1.
TOLERANCES:2.
ANGULAR: BEND3.
MATERIAL COATINGS TO BE SPECIFIED BY THE ENGINEER4.
DO NOT SCALE THIS DRAWING1.
THIS DRAWING AND THE COPYRIGHT THEREIN ARE THE2.
PROPERTY OF LINDAPTER INTERNATIONAL. IT IS ISSUED ON
THE CONDITION THAT IT MUST NOT BE USED, COPIED,
DISTRIBUTED OR EXHIBITED WITHOUT WRITTEN PERMISSION
AND CONSENT. THE DRAWING MUST ALSO NOT BE USED
FOR ANY OTHER PURPOSE THAN WHICH IT IS ISSUED.
IT IS THE RESPONSIBILITY OF THE ENGINEER TO PERFORM3.
ALL REASONABLE CHECKS ON THE SUPPORTING AND
SUPPORTED MEMBERS. THAT IS LOCAL TO THE
CONNECTION AND THE LINDAPTER COMPONENTS, BOTH
FOR THE LOAD APPLIED AND THE CLAMPING FORCE
GENERATED FROM THE TIGHTENING OF THE FASTENERS.
IF FELT NECESSARY, WHERE EXCESSIVE VIBRATION MAY BE4.
A CONCERN, IT IS ACCEPTABLE FOR CERTAIN TYPES OF
ANTI-VIBRATION LOCKING DEVICES SUCH AS, BUT NOT
LIMITED TO, PROPRIETARY WASHERS AND NUTS TO BE
USED WITH LINDAPTER COMPONENTS AND/OR
ASSEMBLIES; SPRING WASHERS OF ANY TYPE ARE NOT
RECOMMENDED. IN THESE SITUATIONS IT IS IMPORTANT
THAT THE MANUFACTURER'S INSTALLATION INSTRUCTIONS
ARE FOLLOWED. NO GUARANTEES OR WARRANTIES ARE
IMPLIED.
817-467-5700
sales@all-profasteners.comwww.all-profasteners.com

9. A
New Interface Angle,
3/8" Thick Minimum
New Angle New Angle
1
3
16 "
Existing Truss
9
16 " THRU
W
W + 9/16"
1-7/16"
MIN
New Angle
Bolted to
Interface Angle
DETAIL A
SCALE 2 : 3
Lindapter LLR050 Clamp
Suitable for 1/8" - 1/2"
Existing Angle Thickness
Ø1/2" Grade 5 Fully Threaded
Bolt with Nut & Washer
For combined loadings the current relevant national
standard should be taken into consideration
Lindapter LLR050 Data:
Static Tensile SWL per
Single Clamp =
1300 lbs
Factor of Safety :
5 : 1
Static Slip SWL per
Pair of Clamps=
157 lbs
Factor of Safety :
5 : 1
Lindapter Fastener
Tightening Torque =
50 ft-lb
DWG. NO. REV.
CHECKEDDATE
WEIGHT:
DESCRIPTIONREV. DATEBY
0SW10150-AR
A.R. 14-SEP-2016
New Angles to
Existing Truss
Concept Design
CUSTOMER
GB-08676
ENQUIRY N.
SCALE:
DRAWN
DRAWING TITLE
I.P.
NOT TO SCALE
A C C E P T N O S U B S T I T U T E
PROJECT
DRAWING NOTES:
GENERAL NOTES:
DIMENSIONS ARE IN INCHES1.
TOLERANCES:2.
ANGULAR: BEND3.
MATERIAL COATINGS TO BE SPECIFIED BY THE ENGINEER4.
DO NOT SCALE THIS DRAWING1.
THIS DRAWING AND THE COPYRIGHT THEREIN ARE THE2.
PROPERTY OF LINDAPTER INTERNATIONAL. IT IS ISSUED ON
THE CONDITION THAT IT MUST NOT BE USED, COPIED,
DISTRIBUTED OR EXHIBITED WITHOUT WRITTEN PERMISSION
AND CONSENT. THE DRAWING MUST ALSO NOT BE USED
FOR ANY OTHER PURPOSE THAN WHICH IT IS ISSUED.
IT IS THE RESPONSIBILITY OF THE ENGINEER TO PERFORM3.
ALL REASONABLE CHECKS ON THE SUPPORTING AND
SUPPORTED MEMBERS. THAT IS LOCAL TO THE
CONNECTION AND THE LINDAPTER COMPONENTS, BOTH
FOR THE LOAD APPLIED AND THE CLAMPING FORCE
GENERATED FROM THE TIGHTENING OF THE FASTENERS.
IF FELT NECESSARY, WHERE EXCESSIVE VIBRATION MAY BE4.
A CONCERN, IT IS ACCEPTABLE FOR CERTAIN TYPES OF
ANTI-VIBRATION LOCKING DEVICES SUCH AS, BUT NOT
LIMITED TO, PROPRIETARY WASHERS AND NUTS TO BE
USED WITH LINDAPTER COMPONENTS AND/OR
ASSEMBLIES; SPRING WASHERS OF ANY TYPE ARE NOT
RECOMMENDED. IN THESE SITUATIONS IT IS IMPORTANT
THAT THE MANUFACTURER'S INSTALLATION INSTRUCTIONS
ARE FOLLOWED. NO GUARANTEES OR WARRANTIES ARE
IMPLIED.
www.lindapterusa.com
OFFICIAL LINDAPTER DISTRIBUTOR:
817-467-5700
sales@all-profasteners.comwww.all-profasteners.com