Mengenal Trunk, VTP, dan STP
Seiring berkembangnya jaringan untuk usaha kecil atau menengah, manajemen dibutuhkan dalam mengelola perkembangan jaringan. Dalam tugas sebelumnya, Anda belajar bagaimana untuk membuat dan mengelola VLAN dan trunks menggunakan command Cisco IOS. Fokusnya adalah pada pengelolaan informasi VLAN pada switch tunggal.
Mengenal Trunk, VTP, dan STP
Seiring berkembangnya jaringan untuk usaha kecil atau menengah, manajemen dibutuhkan dalam mengelola perkembangan jaringan. Dalam tugas sebelumnya, Anda belajar bagaimana untuk membuat dan mengelola VLAN dan trunks menggunakan command Cisco IOS. Fokusnya adalah pada pengelolaan informasi VLAN pada switch tunggal.
1. Konfigurasi Frame-Relay Multipoint & Point-to-Point
Untuk mengkofigurasi Frame Relay seperti pada gambar tersebut dapat dilakukan dengan cara
sebagai berikut ,
Pada Router1 tentukan interface yang akan dijadikan sebagai subinterface untuk access multipoint dan Point-to-
Point. Interface serial 2/0 akan dijadikan sebagai subinterface nya. Lebih jelas lihat cara konfigurasi Frame -Relay
Multipoint & Point-to-Point …
Konfigurasi Router1
interface Serial2/0
no ip address
encapsulation frame-relay
no keepalive
clock rate 56000
!
interface Serial2/0.1 point-to-point
ip address 172.16.10.2 255.255.255.0
frame-relay interface-dlci 100
!
interface Serial2/0.2 multipoint
ip address 172.16.20.2 255.255.255.0
frame-relay interface-dlci 200
frame-relay interface-dlci 300
!
router rip
network 172.16.0.0
Konfigurasi Router2
interface Serial2/0
ip address 172.16.10.1 255.255.255.0
encapsulation frame-relay
frame-relay interface-dlci 100
no keepalive
clock rate 56000
!
router rip
network 172.16.0.0
!
Konfigurasi Router3
interface Serial2/0
ip address 172.16.20.1 255.255.255.0
encapsulation frame-relay
frame-relay interface-dlci 200
no keepalive
clock rate 56000
!
router rip
network 172.16.0.0
!
Konfigurasi Router 4
interface Serial2/0
ip address 172.16.20.3 255.255.255.0
encapsulation frame-relay
frame-relay interface-dlci 300
no keepalive
clock rate 56000
!
router rip
network 172.16.0.0
!
Setelah konfigurasi masing-masing router selesai dilakukan, langkah selanjutnya mengkonfigurasi Cloud
sebagai Frame-Relay Connection. Untuk dapat melakukan hal itu dilakukan konfigurasi manual,
pada Cloud terdapat settingan untuk Frame-Relay. Akan tetapi jangan lupa membuat routing tabel pada masing-masing
router agar transmisi packet data bisa dilakukan. Pembuatan routing tabel dapat dilakukan secara statik
2. routing maupun dinamic routing tergantung kondisi dan tingkat kesulitan. Untuk konfigurasi ini aku sengaja
pake Routing RIP karena lebih mudah.
Kalo semua telah terkonfigurasi secara baik, lakukan percobaan terhadap tiap-tiap router bilamana Frame-Relay
bekerja dan dapat berkomunikasi dengan router lain melalui Cloud dengan cara “show frame-relay map” …
contoh untuk router1
R1#sh frame-relay map
Serial2/0.1 (up): point-to-point dlci, dlci 100, broadcast, status defined, active
Serial2/0.2 (up): ip 172.16.20.1 dlci 200, dynamic, broadcast, CISCO, status defined, active
Serial2/0.2 (up): ip 172.16.20.3 dlci 300, dynamic, broadcast, CISCO, status defined, active
Jelas terlihat access point-to-point dengan DLCI 100 frame-relay sedang active, begitu denganaccess
multipoint dengan DLCI 200 dan DLCI 300 active. show frame-relay lmi dilakukan untuk melihat status koneksi
pada frame-relay
R1#sh frame-relay lmi
LMI Statistics for interface Serial2/0 (Frame Relay DTE) LMI TYPE = CISCO
Invalid Unnumbered info 0 Invalid Prot Disc 0
Invalid dummy Call Ref 0 Invalid Msg Type 0
Invalid Status Message 0 Invalid Lock Shift 0
Invalid Information ID 0 Invalid Report IE Len 0
Invalid Report Request 0 Invalid Keep IE Len 0
Num Status Enq. Sent 159 Num Status msgs Rcvd 144
Num Update Status Rcvd 0 Num Status Timeouts 16
LMI Statistics for interface Serial2/0.1 (Frame Relay DTE) LMI TYPE = CISCO
Invalid Unnumbered info 0 Invalid Prot Disc 0
Invalid dummy Call Ref 0 Invalid Msg Type 0
Invalid Status Message 0 Invalid Lock Shift 0
Invalid Information ID 0 Invalid Report IE Len 0
Invalid Report Request 0 Invalid Keep IE Len 0
Num Status Enq. Sent 159 Num Status msgs Rcvd 144
Num Update Status Rcvd 0 Num Status Timeouts 16
LMI Statistics for interface Serial2/0.2 (Frame Relay DTE) LMI TYPE = CISCO
Invalid Unnumbered info 0 Invalid Prot Disc 0
Invalid dummy Call Ref 0 Invalid Msg Type 0
Invalid Status Message 0 Invalid Lock Shift 0
Invalid Information ID 0 Invalid Report IE Len 0
Invalid Report Request 0 Invalid Keep IE Len 0
Num Status Enq. Sent 159 Num Status msgs Rcvd 144
Num Update Status Rcvd 0 Num Status Timeouts 16
Pada status tersebut lebih jelas terlihat koneksi Point-to-Point dan Multipoint Frame-Relay