The KES7000 conductive immunity test system complies with ISO7637, which is one of an EMC test standards for automotive electronics. This system consists of the KES7700 Series transient immunity tester, KES7400 Series supply voltage variations tester, and KES7100 application software dedicated to the KES7000 system. This product configuration supports JASO standards and the specific test requirements of various auto makers with options or custom orders.
Increasing importance of EMC tests for automotive electronics
Today, automobiles need to satisfy more strict social requirements of the environmental performance (e.g., improved fuel efficiency and measures for exhaust gas) and safety (e.g., on-board safety devices) as well as usability (e.g., driveability and comfort). It is immeasurable how much electronics are contributing to solutions of those requirements, and electronics is taking on more importance in the future.
Electronics has come into wide use not only in the automobile industry but also various other industries and our daily life. In particular, electronics has become widespread in the field of information communication in recent years. However, on the other hand, the widespread of electronics is yielding environments where electromagnetic waves are emitted around, and this may possibly cause confusion of telecommunication, bad influence on health, and other new misgivings. Therefore, automobile on-board electronic devices now need to be produced so that they have no unnecessary electromagnetic wave emission and are tolerant of electromagnetic waves, and the EMC tests are taking on more importance to satisfy those needs.
Catalog Relay Idec
Beeteco.com là trang mua sắm trực tuyến thiết bị điện - Tự động hóa uy tín tại Việt Nam.
Chuyên cung cấp các thiết bị: Đèn báo nút nhấn, Relay, Timer, Contactor, MCCB ELCB, Biến tần, Van, Thiết bị cảm biến, phụ kiện tủ điện, .... Từ các thương hiệu hàng đầu trên thế giới.
www.beeteco.com @ Công ty TNHH TM KT ASTER
Số 7 Đại Lộ Độc Lập, KCN Sóng Thần 1, P. Dĩ An, Tx. Dĩ An, Bình Dương
www.facebook.com/beeteco
Tel: 0650 3617 012
DĐ: 0904 676 925
Catalogue Timer Idec
Beeteco.com là trang mua sắm trực tuyến thiết bị điện - Tự động hóa uy tín tại Việt Nam.
Chuyên cung cấp các thiết bị: Đèn báo nút nhấn, Relay, Timer, Contactor, MCCB ELCB, Biến tần, Van, Thiết bị cảm biến, phụ kiện tủ điện, .... Từ các thương hiệu hàng đầu trên thế giới.
www.beeteco.com @ Công ty TNHH TM KT ASTER
Số 7 Đại Lộ Độc Lập, KCN Sóng Thần 1, P. Dĩ An, Tx. Dĩ An, Bình Dương
www.facebook.com/beeteco
Tel: 0650 3617 012
DĐ: 0904 676 925
Catalog bộ nguồn IDEC PS5R-S Power Supply
Beeteco.com là trang mua sắm trực tuyến thiết bị điện - Tự động hóa uy tín tại Việt Nam.
Chuyên cung cấp các thiết bị: Đèn báo nút nhấn, Relay, Timer, Contactor, MCCB ELCB, Biến tần, Van, Thiết bị cảm biến, phụ kiện tủ điện, .... Từ các thương hiệu hàng đầu trên thế giới.
www.beeteco.com @ Công ty TNHH TM KT ASTER
Địa chỉ : Số 7/31 KDC Thương Mại Sóng Thần, KP. Nhị Đồng 1, P. Dĩ An, Tx. Dĩ An, Tỉnh Bình Dương
FB: www.facebook.com/beeteco
Email: contact@beeteco.com
Tel: 0650 3617 012
Hotline: 0909.41.61.43
Catalog cs iec industrial_control_dienhathe.vnDien Ha The
Khoa Học - Kỹ Thuật & Giải Trí: http://phongvan.org
Tài Liệu Khoa Học Kỹ Thuật: http://tailieukythuat.info
Thiết bị Điện Công Nghiệp - Điện Hạ Thế: http://dienhathe.vn
Công ty cổ phần Hạo Phương xin gửi đến quý khách hàng Catalog relay Idec gồm đầy đủ các thông tin cơ bản như: thông số kỹ thuật, kích thước, sơ đồ dây….
Tham khảo các dòng Relay Idec thông dụng tại thị trường Việt Nam: RU4S, RU2S, RY4S, RM2S, RJ1S,….
Thiết kế của Relay Idec tinh tế đến từng chi tiết, sản phẩm luôn đảm bảo độ chính xác và chất lượng. Các ổ cắm dễ dàng sử dụng và có thể gắn trên Din rail, panel hoặc PCB.
Công ty Cổ phần Hạo Phương xin gửi đến quý khách hàng Catalog Timer đầy đủ và chi tiết cấu tạo các dòng timer của nhà sản xuất Idec Izumi đến từ Nhật bản.
Quý khách có nhu cầu mua hàng hoặc hợp tác cùng chúng tôi xin vui lòng liên hệ theo địa chỉ :
CÔNG TY CỔ PHẦN HẠO PHƯƠNG
Trụ sở chính:
Địa chỉ: Số 88 đường Vĩnh Phú 40, Kp. Hòa Long, P. Vĩnh Phú, Thuận An, Bình Dương.
Văn phòng Hà Nội:
Địa chỉ: Số 95 TT4 - KĐT Mỹ Đình Sông Đà - Phường Mỹ Đình - Q. Nam Từ Liêm - Hà Nội
Chi nhánh Cambodia:
Địa chỉ: The Park Land SenSok, Borey Chip Mong, House Number 22, P11.Sangkat Phnom Penh Thmey, Khan San Sok, Phnom Penh.
Email: cs@haophuong.com - Website: haophuong.com
Facebook: https://www.facebook.com/haophuongcompany/
HOTLINE: 1800 6547
This document provides information on YUEQING FEEO ELECTRIC CO.,LTD, a professional solar PV electric components manufacturer located in Yueqing City, China. It introduces their FEO-63 Solar DC Mini Circuit Breaker (DC MCB), including its specifications, applications, characteristic curve, dimensions, and connection details. The FEO-63 is designed to provide overcurrent protection within appliances or electrical equipment for direct current applications, with a rated operating voltage range of DC12V - DC1000V and rated current from 1A to 63A.
Catalog Relay Idec
Beeteco.com là trang mua sắm trực tuyến thiết bị điện - Tự động hóa uy tín tại Việt Nam.
Chuyên cung cấp các thiết bị: Đèn báo nút nhấn, Relay, Timer, Contactor, MCCB ELCB, Biến tần, Van, Thiết bị cảm biến, phụ kiện tủ điện, .... Từ các thương hiệu hàng đầu trên thế giới.
www.beeteco.com @ Công ty TNHH TM KT ASTER
Số 7 Đại Lộ Độc Lập, KCN Sóng Thần 1, P. Dĩ An, Tx. Dĩ An, Bình Dương
www.facebook.com/beeteco
Tel: 0650 3617 012
DĐ: 0904 676 925
Catalogue Timer Idec
Beeteco.com là trang mua sắm trực tuyến thiết bị điện - Tự động hóa uy tín tại Việt Nam.
Chuyên cung cấp các thiết bị: Đèn báo nút nhấn, Relay, Timer, Contactor, MCCB ELCB, Biến tần, Van, Thiết bị cảm biến, phụ kiện tủ điện, .... Từ các thương hiệu hàng đầu trên thế giới.
www.beeteco.com @ Công ty TNHH TM KT ASTER
Số 7 Đại Lộ Độc Lập, KCN Sóng Thần 1, P. Dĩ An, Tx. Dĩ An, Bình Dương
www.facebook.com/beeteco
Tel: 0650 3617 012
DĐ: 0904 676 925
Catalog bộ nguồn IDEC PS5R-S Power Supply
Beeteco.com là trang mua sắm trực tuyến thiết bị điện - Tự động hóa uy tín tại Việt Nam.
Chuyên cung cấp các thiết bị: Đèn báo nút nhấn, Relay, Timer, Contactor, MCCB ELCB, Biến tần, Van, Thiết bị cảm biến, phụ kiện tủ điện, .... Từ các thương hiệu hàng đầu trên thế giới.
www.beeteco.com @ Công ty TNHH TM KT ASTER
Địa chỉ : Số 7/31 KDC Thương Mại Sóng Thần, KP. Nhị Đồng 1, P. Dĩ An, Tx. Dĩ An, Tỉnh Bình Dương
FB: www.facebook.com/beeteco
Email: contact@beeteco.com
Tel: 0650 3617 012
Hotline: 0909.41.61.43
Catalog cs iec industrial_control_dienhathe.vnDien Ha The
Khoa Học - Kỹ Thuật & Giải Trí: http://phongvan.org
Tài Liệu Khoa Học Kỹ Thuật: http://tailieukythuat.info
Thiết bị Điện Công Nghiệp - Điện Hạ Thế: http://dienhathe.vn
Công ty cổ phần Hạo Phương xin gửi đến quý khách hàng Catalog relay Idec gồm đầy đủ các thông tin cơ bản như: thông số kỹ thuật, kích thước, sơ đồ dây….
Tham khảo các dòng Relay Idec thông dụng tại thị trường Việt Nam: RU4S, RU2S, RY4S, RM2S, RJ1S,….
Thiết kế của Relay Idec tinh tế đến từng chi tiết, sản phẩm luôn đảm bảo độ chính xác và chất lượng. Các ổ cắm dễ dàng sử dụng và có thể gắn trên Din rail, panel hoặc PCB.
Công ty Cổ phần Hạo Phương xin gửi đến quý khách hàng Catalog Timer đầy đủ và chi tiết cấu tạo các dòng timer của nhà sản xuất Idec Izumi đến từ Nhật bản.
Quý khách có nhu cầu mua hàng hoặc hợp tác cùng chúng tôi xin vui lòng liên hệ theo địa chỉ :
CÔNG TY CỔ PHẦN HẠO PHƯƠNG
Trụ sở chính:
Địa chỉ: Số 88 đường Vĩnh Phú 40, Kp. Hòa Long, P. Vĩnh Phú, Thuận An, Bình Dương.
Văn phòng Hà Nội:
Địa chỉ: Số 95 TT4 - KĐT Mỹ Đình Sông Đà - Phường Mỹ Đình - Q. Nam Từ Liêm - Hà Nội
Chi nhánh Cambodia:
Địa chỉ: The Park Land SenSok, Borey Chip Mong, House Number 22, P11.Sangkat Phnom Penh Thmey, Khan San Sok, Phnom Penh.
Email: cs@haophuong.com - Website: haophuong.com
Facebook: https://www.facebook.com/haophuongcompany/
HOTLINE: 1800 6547
This document provides information on YUEQING FEEO ELECTRIC CO.,LTD, a professional solar PV electric components manufacturer located in Yueqing City, China. It introduces their FEO-63 Solar DC Mini Circuit Breaker (DC MCB), including its specifications, applications, characteristic curve, dimensions, and connection details. The FEO-63 is designed to provide overcurrent protection within appliances or electrical equipment for direct current applications, with a rated operating voltage range of DC12V - DC1000V and rated current from 1A to 63A.
Bu pdfte LS kontaktörlerin en önemli özellikleri ve kullanım şekli anlatılmıştır. Bu sayede LS kontaktörlerin bağlantısı, montajı kesme değerleri konusunda birçok bilgi alabilirsiniz.
http://www.saypro.com.tr/lg-kontaktor-secmeniz-icin-5-neden/
This document provides specifications for the Power PCB Relay G2R, including:
- It is available in non-latching and latching models with contact configurations including 1-pole and 2-pole.
- Models include general purpose, high capacity, and high sensitivity options with silver alloy contacts.
- Electrical ratings include maximum switching capacity, operating voltage/current, and minimum load.
- Performance specifications cover operate/release times, bounce time, frequency, insulation/dielectric strength.
- Environmental ratings include temperature, humidity, vibration, and shock resistance.
- Dimensions and weight are provided for each model.
This document provides specifications for several product lines from Singnile Technology Co., Ltd:
- The MPPT Series includes solar inverters ranging from 1000VA to 5000VA with maximum solar input power of 600W to 3000W.
- The PWM Series are PWM control inverters from 1000VA to 5000VA for 12V, 24V, or 48V battery systems.
- The SI Series are integrated PWM inverters from 300W to 3000W that also function as UPS systems.
- The SA Series are integrated AC solar inverters from 100W to 3000W with built-in lead acid battery storage and solar charge controller.
This document provides specifications for Pacific Scientific synchronous motors including:
- Performance curves showing torque vs inertia for 72 RPM and 60 RPM motors.
- Tables listing torque, inertia, current and other ratings for various NEMA 34 and 42 frame motors.
- Diagrams of phase shift networks required for motor startup.
- Information on selecting resistor and capacitor values for phase shift networks.
This document provides information on the ADXL335, a small, low power, 3-axis accelerometer. It has a measurement range of ±3g and operates from a 1.8V to 3.6V supply with typical current consumption of 350uA. It outputs analog voltage signals from each axis that are proportional to acceleration. The user can select the bandwidth for each axis using external capacitors from 0.5Hz to 1600Hz for X and Y, and 0.5Hz to 550Hz for Z. It is packaged in a 4mmx4mmx1.45mm LFCSP.
This document provides information about Rotech Systems and their motion sensor products. Rotech has been monitoring equipment since 1983 and offers reliable monitoring solutions including shaft encoders, vibration sensors, and conveyor belt wheel sensors. The document provides details on various Rotech sensor models, including the PE4000 polypropylene shaft encoder, VS4000 vibration sensor, and PWE6000 conveyor belt wheel sensor. Installation and commissioning instructions are also provided.
Ls catalog thiet bi tu dong dpr 1000-e_dienhathe.vnDien Ha The
Khoa Học - Kỹ Thuật & Giải Trí: http://phongvan.org
Tài Liệu Khoa Học Kỹ Thuật: http://tailieukythuat.info
Thiết bị Điện Công Nghiệp - Điện Hạ Thế: http://dienhathe.org
Iwatsu’s B-H analyzers which hiring CROSS-POWER method (IEC62044-3) enable precise and highly
accurate measurement embedded minimized phase error integration on frequency spectrum with current
detecting resisters and compensation on detecting circuit with full compensation on amplitude and phase
characteristics.
https://www.n-denkei.com/singapore/inquiry/
This document provides specifications for various types of relays and sockets manufactured by Dienhathe including:
- General purpose electromechanical relays and sockets available in SPDT, DPDT, and other contact configurations ranging from 1A to 16A contact ratings.
- Universal relays with DPDT and 4PDT configurations and 10A contact ratings.
- Miniature relays available in DPDT, 4PDT, and other configurations with contact ratings from 1A to 6A.
- Power relays available in SPDT, DPDT, 3PDT, and 4PDT with 10A contact ratings.
- Latch relays including dual coil models with DPDT configurations and 10A contact ratings
This document provides technical specifications for an ABB REF615 ANSI feeder protection relay. It includes 30 tables that specify details such as power supply requirements, input/output ratings, communication protocols, environmental testing procedures, EMC compliance, and supported protection functions. The relay is approved to relevant safety and EMC standards and directives.
This document is an instruction manual for VLT series 3002-3250 adjustable frequency drives. It provides specifications for the different drive models including their nominal horsepower ratings, current and power ratings, voltage and frequency capabilities, and enclosure types. It also lists the applicable EMC standards and provides operating temperature ranges and other technical specifications.
With alarm function of housing grounding testing and external voltage input, to guaranty personal security
Offer independent Aux. DC to tested devices, 0 ~ 300V/0.6A (Poleless and adjustable)
Testing interface offer unique output monitoring function and Pre-curve-tracing function
Price: AUD $ 47,520.00 ex GST
Hioki 3291-50 Clamp-On HiTester with an innovative flip clamp design and flip display to see measurement readings from any angle.
Available for sales, rent, hire and lease @ http://www.supremetechnology.com.au/product/hioki-3291-50-clamp-on-hitester.aspx?Id=82&ProductType=Regular
Catalog ls metasol mc e_1004_denhathe.vnDien Ha The
Khoa Học - Kỹ Thuật & Giải Trí: http://phongvan.org
Tài Liệu Khoa Học Kỹ Thuật: http://tailieukythuat.info
Thiết bị Điện Công Nghiệp - Điện Hạ Thế: http://dienhathe.org
Catalog ls metasol mc_e_1008_denhathe.vnDien Ha The
Khoa Học - Kỹ Thuật & Giải Trí: http://phongvan.org
Tài Liệu Khoa Học Kỹ Thuật: http://tailieukythuat.info
Thiết bị Điện Công Nghiệp - Điện Hạ Thế: http://dienhathe.org
ECC EST-300 Series Next-Generation Hipot Tester - High Output Rating As Compa...Aimil Ltd
The EST-300 next-generation Hipot tester combines industry-leading compact size with Unbeatable performance. This new series economically integrates AC, DC withstand, and
Insulation resistance into a single solution. The Hipot tester is highly portable and fits readily in any spatially limited testing environment. The EST-300 series provides a robust set of features. That includes high output rating, ARC detection, ramp-high, charge-low, and fast discharge to enhance overall testing efficiency and safety by preventing the common errors and detecting any dielectric breakdowns during tests on the DUT. This Product Originates from Extech Electronics Co., Taiwan and Aimil Ltd. is their major distributors and suppliers in India.
Idec catalog switching power supplies ep1196 0ps5r-sallslimDien Ha The
The document provides specifications for IDEC's PS5R-S series of switching power supplies. It describes the slim size and various wattage options from 10W to 240W. Key features include universal AC input, DIN rail or panel mounting, finger-safe spring-loaded terminals, and compliance with various safety standards. Charts provide details on electrical specifications, derating curves for output current vs. operating temperature, and block diagrams of the power supply design.
Idec catalog switching power supplies ep1196 0ps5r-sallslimDien Ha The
The document provides specifications for IDEC's PS5R-S series of switching power supplies. It describes the slim size and compact dimensions of the supplies. Various models are available with output capacities ranging from 10W to 240W and output voltages of 5V, 12V, or 24V. The document includes detailed specifications for electrical performance, safety approvals, mechanical characteristics, and diagrams of the internal components. Installation guidelines and optional mounting accessories are also summarized.
This document provides a selection guide for various timer models, including:
- GT3 series multi-function timers with options for OFF delay, star-delta, and twin-timer configurations.
- Multi-mode timers that offer four operation modes in one unit, including ON delay and cycle.
- Miniature GT5 timers and GE1A timers with different time ranges and output configurations.
Technical specifications are provided for each timer such as time ranges, outputs, operating voltages, and standards compliance. Model numbers are listed that vary by configuration, time range, and voltage codes.
This document provides a selection guide for various timer models, including:
- GT3 series multi-function timers with options for OFF delay, star-delta, and twin-timer configurations.
- Multi-mode timers that offer four operation modes in one unit, including ON delay and cycle.
- Miniature GT5 timers and GE1A timers with different time ranges and output configurations.
Technical specifications are given for each model including time ranges, outputs, operating voltages, and standards compliance. A wide variety of timers are available to suit different applications.
This document describes Switch Mode Power Supply models ranging from 15W to 350W. It provides specifications for each model including input/output ratings, efficiency, protection features, construction details, and standards compliance. The power supplies offer high reliability and stable operation for equipment applications with output voltages of 5V, 12V, 15V, 24V, 36V or 48V.
This document provides specifications for a 120W DIN rail power supply with the following key details:
- It has a single 120W output with a voltage range of 22-28V and a current of 5A.
- The input voltage range is 85-264VAC. It has protections such as overload, overvoltage, and overtemperature protections.
- Additional features include compact design, easy wire connection, 10 year lifetime, shock/vibration resistance, and convection cooling.
Bu pdfte LS kontaktörlerin en önemli özellikleri ve kullanım şekli anlatılmıştır. Bu sayede LS kontaktörlerin bağlantısı, montajı kesme değerleri konusunda birçok bilgi alabilirsiniz.
http://www.saypro.com.tr/lg-kontaktor-secmeniz-icin-5-neden/
This document provides specifications for the Power PCB Relay G2R, including:
- It is available in non-latching and latching models with contact configurations including 1-pole and 2-pole.
- Models include general purpose, high capacity, and high sensitivity options with silver alloy contacts.
- Electrical ratings include maximum switching capacity, operating voltage/current, and minimum load.
- Performance specifications cover operate/release times, bounce time, frequency, insulation/dielectric strength.
- Environmental ratings include temperature, humidity, vibration, and shock resistance.
- Dimensions and weight are provided for each model.
This document provides specifications for several product lines from Singnile Technology Co., Ltd:
- The MPPT Series includes solar inverters ranging from 1000VA to 5000VA with maximum solar input power of 600W to 3000W.
- The PWM Series are PWM control inverters from 1000VA to 5000VA for 12V, 24V, or 48V battery systems.
- The SI Series are integrated PWM inverters from 300W to 3000W that also function as UPS systems.
- The SA Series are integrated AC solar inverters from 100W to 3000W with built-in lead acid battery storage and solar charge controller.
This document provides specifications for Pacific Scientific synchronous motors including:
- Performance curves showing torque vs inertia for 72 RPM and 60 RPM motors.
- Tables listing torque, inertia, current and other ratings for various NEMA 34 and 42 frame motors.
- Diagrams of phase shift networks required for motor startup.
- Information on selecting resistor and capacitor values for phase shift networks.
This document provides information on the ADXL335, a small, low power, 3-axis accelerometer. It has a measurement range of ±3g and operates from a 1.8V to 3.6V supply with typical current consumption of 350uA. It outputs analog voltage signals from each axis that are proportional to acceleration. The user can select the bandwidth for each axis using external capacitors from 0.5Hz to 1600Hz for X and Y, and 0.5Hz to 550Hz for Z. It is packaged in a 4mmx4mmx1.45mm LFCSP.
This document provides information about Rotech Systems and their motion sensor products. Rotech has been monitoring equipment since 1983 and offers reliable monitoring solutions including shaft encoders, vibration sensors, and conveyor belt wheel sensors. The document provides details on various Rotech sensor models, including the PE4000 polypropylene shaft encoder, VS4000 vibration sensor, and PWE6000 conveyor belt wheel sensor. Installation and commissioning instructions are also provided.
Ls catalog thiet bi tu dong dpr 1000-e_dienhathe.vnDien Ha The
Khoa Học - Kỹ Thuật & Giải Trí: http://phongvan.org
Tài Liệu Khoa Học Kỹ Thuật: http://tailieukythuat.info
Thiết bị Điện Công Nghiệp - Điện Hạ Thế: http://dienhathe.org
Iwatsu’s B-H analyzers which hiring CROSS-POWER method (IEC62044-3) enable precise and highly
accurate measurement embedded minimized phase error integration on frequency spectrum with current
detecting resisters and compensation on detecting circuit with full compensation on amplitude and phase
characteristics.
https://www.n-denkei.com/singapore/inquiry/
This document provides specifications for various types of relays and sockets manufactured by Dienhathe including:
- General purpose electromechanical relays and sockets available in SPDT, DPDT, and other contact configurations ranging from 1A to 16A contact ratings.
- Universal relays with DPDT and 4PDT configurations and 10A contact ratings.
- Miniature relays available in DPDT, 4PDT, and other configurations with contact ratings from 1A to 6A.
- Power relays available in SPDT, DPDT, 3PDT, and 4PDT with 10A contact ratings.
- Latch relays including dual coil models with DPDT configurations and 10A contact ratings
This document provides technical specifications for an ABB REF615 ANSI feeder protection relay. It includes 30 tables that specify details such as power supply requirements, input/output ratings, communication protocols, environmental testing procedures, EMC compliance, and supported protection functions. The relay is approved to relevant safety and EMC standards and directives.
This document is an instruction manual for VLT series 3002-3250 adjustable frequency drives. It provides specifications for the different drive models including their nominal horsepower ratings, current and power ratings, voltage and frequency capabilities, and enclosure types. It also lists the applicable EMC standards and provides operating temperature ranges and other technical specifications.
With alarm function of housing grounding testing and external voltage input, to guaranty personal security
Offer independent Aux. DC to tested devices, 0 ~ 300V/0.6A (Poleless and adjustable)
Testing interface offer unique output monitoring function and Pre-curve-tracing function
Price: AUD $ 47,520.00 ex GST
Hioki 3291-50 Clamp-On HiTester with an innovative flip clamp design and flip display to see measurement readings from any angle.
Available for sales, rent, hire and lease @ http://www.supremetechnology.com.au/product/hioki-3291-50-clamp-on-hitester.aspx?Id=82&ProductType=Regular
Catalog ls metasol mc e_1004_denhathe.vnDien Ha The
Khoa Học - Kỹ Thuật & Giải Trí: http://phongvan.org
Tài Liệu Khoa Học Kỹ Thuật: http://tailieukythuat.info
Thiết bị Điện Công Nghiệp - Điện Hạ Thế: http://dienhathe.org
Catalog ls metasol mc_e_1008_denhathe.vnDien Ha The
Khoa Học - Kỹ Thuật & Giải Trí: http://phongvan.org
Tài Liệu Khoa Học Kỹ Thuật: http://tailieukythuat.info
Thiết bị Điện Công Nghiệp - Điện Hạ Thế: http://dienhathe.org
ECC EST-300 Series Next-Generation Hipot Tester - High Output Rating As Compa...Aimil Ltd
The EST-300 next-generation Hipot tester combines industry-leading compact size with Unbeatable performance. This new series economically integrates AC, DC withstand, and
Insulation resistance into a single solution. The Hipot tester is highly portable and fits readily in any spatially limited testing environment. The EST-300 series provides a robust set of features. That includes high output rating, ARC detection, ramp-high, charge-low, and fast discharge to enhance overall testing efficiency and safety by preventing the common errors and detecting any dielectric breakdowns during tests on the DUT. This Product Originates from Extech Electronics Co., Taiwan and Aimil Ltd. is their major distributors and suppliers in India.
Idec catalog switching power supplies ep1196 0ps5r-sallslimDien Ha The
The document provides specifications for IDEC's PS5R-S series of switching power supplies. It describes the slim size and various wattage options from 10W to 240W. Key features include universal AC input, DIN rail or panel mounting, finger-safe spring-loaded terminals, and compliance with various safety standards. Charts provide details on electrical specifications, derating curves for output current vs. operating temperature, and block diagrams of the power supply design.
Idec catalog switching power supplies ep1196 0ps5r-sallslimDien Ha The
The document provides specifications for IDEC's PS5R-S series of switching power supplies. It describes the slim size and compact dimensions of the supplies. Various models are available with output capacities ranging from 10W to 240W and output voltages of 5V, 12V, or 24V. The document includes detailed specifications for electrical performance, safety approvals, mechanical characteristics, and diagrams of the internal components. Installation guidelines and optional mounting accessories are also summarized.
This document provides a selection guide for various timer models, including:
- GT3 series multi-function timers with options for OFF delay, star-delta, and twin-timer configurations.
- Multi-mode timers that offer four operation modes in one unit, including ON delay and cycle.
- Miniature GT5 timers and GE1A timers with different time ranges and output configurations.
Technical specifications are provided for each timer such as time ranges, outputs, operating voltages, and standards compliance. Model numbers are listed that vary by configuration, time range, and voltage codes.
This document provides a selection guide for various timer models, including:
- GT3 series multi-function timers with options for OFF delay, star-delta, and twin-timer configurations.
- Multi-mode timers that offer four operation modes in one unit, including ON delay and cycle.
- Miniature GT5 timers and GE1A timers with different time ranges and output configurations.
Technical specifications are given for each model including time ranges, outputs, operating voltages, and standards compliance. A wide variety of timers are available to suit different applications.
This document describes Switch Mode Power Supply models ranging from 15W to 350W. It provides specifications for each model including input/output ratings, efficiency, protection features, construction details, and standards compliance. The power supplies offer high reliability and stable operation for equipment applications with output voltages of 5V, 12V, 15V, 24V, 36V or 48V.
This document provides specifications for a 120W DIN rail power supply with the following key details:
- It has a single 120W output with a voltage range of 22-28V and a current of 5A.
- The input voltage range is 85-264VAC. It has protections such as overload, overvoltage, and overtemperature protections.
- Additional features include compact design, easy wire connection, 10 year lifetime, shock/vibration resistance, and convection cooling.
1. The document provides specifications for programmable AC/DC power sources models EC750SA and EC1000SA, including output voltage, current and power ranges, waveform types, frequency settings, measurement functions, interfaces, and control features.
2. Key features include stable output under various load conditions, a peak current output up to 4 times the rated current, sequence functionality for automated testing, and measurement and protection functions.
3. The units support applications in testing electronics, automobiles, appliances and more through a range of output modes, waveform types, sequencing, and integrated measurement and control capabilities.
NF Programmable Current Amplifier E ca5350
Support a variety of small current measurement
Application: Small current measurements, using optical sensors (PD, APD, PMT) Photodetection with PMT Photodiode Scanning tunneling Microscopy spectroscopy quantum electronics semiconductors MEMS
Leakage Clamp Meter
• Least affected by external stray magnetic field.
• 20mA AC max. in proximity to a 15mm-dia conductor carrying 100A AC
• Frequency Selector Switch to eliminate the effect of harmonics.
• Resolution 0.1mA.
Inc. Accessories: 9097 Carrying Case, R03 × 2, Instruction Manual
Original Opto ACPL-T350 AT350 T350 350 DIP-8 New AVAGOAUTHELECTRONIC
The document describes the ACPL-T350 optocoupler, which contains a GaAsP LED optically coupled to an integrated circuit output stage. It is suited for driving power devices like IGBTs and MOSFETs in applications such as motor controls. Key specifications include a 2.5A peak output current, 15kV/μs CMR, 500ns switching speeds, and an operating temperature range of -40°C to 100°C. The document provides detailed information on electrical characteristics, insulation ratings, packaging, and ordering options.
Hioki BATTERY TESTER BT3554-50
BATTERY HiTESTER BT3561A
BATTERY HiTESTER BT3562A
Fully automated production line testing of large packs for xEVs or large packs of up to 300 V
Omicron CMC 256plus High Precision Relay Test Set and Universal Calibrator Da...Angus Sankaran
Protection test set and universal calibrator in one device
Testing of all relay generations - electromechanical, static, numerical, IEC 61850
Integrated network for testing IEC 61850 IEDs
Original Transistor NPN MPSA18 MPS A18 TO 92 New ONauthelectroniccom
This document provides specifications for the MPSA18 low noise transistor, including:
1) Maximum ratings for voltage, current, and temperature parameters.
2) Typical electrical characteristics such as gain, voltage, and capacitance.
3) Noise characteristics including noise voltage, current, and figures across frequency ranges.
4) Package dimensions and ordering information for the TO-92 packaged transistor.
The document describes the UCC3895 BiCMOS advanced phase-shift PWM controller. It has features such as programmable output turn-on delay, adaptive delay set, bidirectional oscillator synchronization, and voltage-mode or current-mode control. It can operate at frequencies up to 1 MHz with typical operating current of 5 mA at 500 kHz. The UCC3895 is a phase-shift PWM controller that implements full-bridge power stage control by phase shifting one half-bridge with respect to the other, allowing constant frequency pulse-width modulation with zero-voltage switching for high efficiency at high frequencies. It improves on previous controller families with additional features such as enhanced control logic and adaptive delay set.
This document summarizes the specifications and features of a PS50A24 power supply. It has a 24V output that is adjustable, protection from overloads and overvoltage, and operates from 90-265VAC input. It measures 3.89 x 3.81 x 1.41 inches and has safety approvals pending from various organizations.
Công ty TNHH Hạo Phương là đối tác phân phối các thiết bị điện công nghiệp của hãng IDEC IZUMI: đèn báo nút nhấn, relay, timer, PLC, màn hình idec...www.haophuong.com
This document provides specifications for a 320W/48V power supply unit with model number PS320A48. The power supply has a universal input voltage range of 85-265VAC, active power factor correction, safety approvals from multiple organizations, and protections against short circuits, overloads and over voltages. It provides a 48V output that is adjustable between 43.2-52.8V, has a maximum current of 6.7A, and was designed for applications requiring peak currents for motor control.
The document describes the Aurora Trio inverters, including the PVI-6.0-TL and PVI-8.0-TL models. It provides specifications for their key features such as having two independent MPPTs, wide input voltage ranges, high efficiencies, monitoring interfaces, and compliance with various international grid standards. The inverters are designed for outdoor rooftop solar installations and come in variants with and without DC disconnect switches.
Similar to Kikusui Kes7000 Transient Immunity Tester / Voltage Variation Simulator denkei (20)
Multi-channel low noise arbitrary waveform generation system
Multi-channel precision low noise DC voltage source
Multi-channel low noise amplification system
The document discusses the benefits of exercise for mental health. Regular physical activity can help reduce anxiety and depression and improve mood and cognitive functioning. Exercise causes chemical changes in the brain that may help protect against mental illness and improve symptoms.
Ono sokki ds3000 Data Station DS-3000 series Sound and Vibration Real-time...NIHON DENKEI SINGAPORE
1. The DS-3000 Series can perform real-time analysis of noise and vibration generated from various industrial products. It features high-speed processing hardware and easy-to-use software.
2. Real-time octave analysis breaks sounds down into frequency bands similar to human hearing, allowing analysis of noise levels over time. FFT analysis separates waveforms into frequency components.
3. Tracking analysis is useful for analyzing rotational machines like engines. It detects resonance between rotational speed and natural frequencies that could cause problems.
This document provides information on various data loggers including the LR8450, LR8450-01, LR8410-20, LR8431-20, and 8423. It compares their key specifications such as number of channels, maximum sampling interval, input types, and wireless communication capabilities. Application examples are also provided for combining the data loggers with other Hioki instruments to measure values like temperature, resistance, current, voltage, power, and strain.
The document discusses Hioki's lineup of current sensors and current probes for various current measurement applications. It provides details on their specifications and suitability for different use cases, such as evaluating power devices, automotive systems, power quality maintenance, power consumption assessment, and more. The sensors and probes are optimized for measuring currents ranging from miniscule to large magnitudes, operating at frequencies from DC to the GHz range. Models are designed for high-accuracy measurement, waveform observation, and grid power quality control across industries including automotive, renewable energy, and electronics.
This document provides an overview of Hioki's field measuring instruments and their applications in various industrial settings. It introduces Hioki as a leader in test and measuring instruments, with integrated R&D and manufacturing allowing for sustainable product innovation. Various Hioki instruments are then mapped to common applications in factories, including measuring motor insulation, supply voltage, load current, grounding, temperature, and more. Similar mappings are provided for applications in data centers and PV systems.
The document provides an overview of various electrical measuring instruments and testing equipment offered by Hioki, including:
- Battery testers for measuring the internal resistance and open-circuit voltage of batteries used in applications like electric vehicles, power tools, smartphones, and more.
- Motor measurement solutions for performance analysis and quality testing, including power analyzers, clamp sensors, and data loggers.
- Equipment for designing, developing, and testing motors and inverters, such as power analyzers for evaluating efficiency, temperature sensors, and insulation testers.
- Production testing devices like winding testers, breakdown voltage testers, resistance meters, and LCR meters.
- Additional product categories like data loggers, safety test
The DIFFERENTIAL PROBE 9322 provides 3 measurement functions with a single probe: 1) floating measurement of high voltage waveforms up to 1000V AC/DC, 2) detection of surge noise on power supply lines, and 3) true RMS rectified output of high voltage AC. It can be powered by an AC adapter or Hioki’s Probe Power Unit and measures signals up to 2000V DC or 1000V AC with a 1/1000 output.
This document summarizes the features of the KG Load Station Series 300W/1000W electronic loads. It has a revolutionary UI like an oscilloscope for easy operation. It realizes less 35% weight than previous models. It can operate just like a resistor with no minimum voltage requirement. It has high speed current control and 4 models from 300W to 1000W in 125V and 500V ranges.
The document describes the features and capabilities of the Hioki PW8001 power analyzer. It can measure up to 8 power channels with the highest accuracy from DC to high frequencies. It accurately captures power fluctuations from high-speed switching converters. It also provides full compatibility with various current sensors and can automatically perform phase correction for accurate measurement of high-frequency, low power factor power.
PBZ Series Intelligent Bi-Polar Power Supplies
The PBZ series is a bipolar type DC regulated power source that can continuously change both + and – polarities passing through 0 without changing the output terminal.
By adopting a “Switching + Linear” system, the PBZ is able to realize both drastic weight reduction as well as high speed and low noise operation. Since operation covers 4 quadrants, power can be both supplied (source) and absorbed (sink). The PBZ can also drive inductive or capacitive loads. The unit also equips a signal generator function which enables waveform and sequence creation. The PBZ is also capable of synchronized operation which is required for voltage variation tests, and it can also be expanded for large current applications through master-slave parallel operation.
This document provides information on various measurement solutions for the automotive industry, including:
1) Systems for measuring engine-related parameters like combustion chamber volume, analyzing engine noise and vibrations, and inspecting transmission components.
2) Solutions for testing vehicle bodies, including analyzing vibration modes and locating sound sources.
3) Methods for evaluating interior comfort, such as measuring sound absorption and performing psychoacoustic assessments.
4) A system for testing muffler acoustic performance.
The document also provides information on related products like multi-channel analyzers, sensors, and anechoic chambers.
Inspect solar panel bypass diodes for opens and shorts in broad daylight without covering panels
INSPECT SOLAR PANEL BYPASS DIODES FOR OPENS AND SHORTS IN BROAD DAYLIGHT WITHOUT COVERING PANELS
Traditionally, bypass diodes can only be inspected for good working condition at night or when power is not being generated by the solar panels in order to verify that any applied current is guided past the solar cells.
With the FT4310, you can detect for open faults even when the sun is out without covering the panels.
Testing can also be performed at night.
*Testing for short-circuit faults can only be performed during the day.
DP800 series includes single output, two output and three output programmable linear DC power supply. They have pure output, excellent performance indicators, multiple analysis functions, rich interfaces, and can meet the diverse testing needs.
This document lists specifications for 7 load cell models - the RZ-1 through RZ-100. Each model is designed to measure different maximum force ranges from 1kg to 100kg with varying minimum increments between 0.1g and 10g. The document also provides model numbers, maximum ratings, and force ranges for each load cell.
"IOS 18 CONTROL CENTRE REVAMP STREAMLINED IPHONE SHUTDOWN MADE EASIER"Emmanuel Onwumere
In iOS 18, Apple has introduced a significant revamp to the Control Centre, making it more intuitive and user-friendly. One of the standout features is a quicker and more accessible way to shut down your iPhone. This enhancement aims to streamline the user experience, allowing for faster access to essential functions. Discover how iOS 18's redesigned Control Centre can simplify your daily interactions with your iPhone, bringing convenience right at your fingertips.
Building a Raspberry Pi Robot with Dot NET 8, Blazor and SignalRPeter Gallagher
In this session delivered at NDC Oslo 2024, I talk about how you can control a 3D printed Robot Arm with a Raspberry Pi, .NET 8, Blazor and SignalR.
I also show how you can use a Unity app on an Meta Quest 3 to control the arm VR too.
You can find the GitHub repo and workshop instructions here;
https://bit.ly/dotnetrobotgithub
2. 2
Transient Immunity Tester KES7700 Series are transient surge tester that utilizes a compact unit system. A surge generator circuit
is installed for each pulse unit as the tester meets the requirement of ISO7637-2, ISO7637-3, ISO16750-2, JASO D001, SAE
J1113, and other standards. The KES7700 Series meets a broad range of independent automobile manufacturer standards as well.
The ISO7637 standard specifies Pulse 1, Pulse 2a, and Pulse 3a/3b, while the ISO16750-2 standard specifies Pulse 5a/5b. Each
pulse simulates the following: electromagnetic phenomena produced by electronic equipment joined by wire harnesses during
an automobile's normal operation, electromagnetic coupling during switch opening and closing, and load dump surges produced
by the alternator when the battery is disconnected. Each pulse also tests the tolerance of on-board electronic equipment. In this
testing, malfunctions and breakdowns involving on-board electronic equipment are evaluated.
KES7700 Series - Transient Immunity Tester
Full compliance with ISO 7637-2.2004, ISO 7637-2.2011, ISO 7637-3.2007, ISO 16750-2.2010
Load dump suppressor for pulse 5b
The use of an amplifier circuit and a dedicated suppressor allows the system to generate waveforms that faithfully comply with the
pertinent standards not only for pulse 5a required by ISO 7637 but also for pulse 5b.
Compact modular cabinet
The modular cabinet allows surge waveforms to be added with ease.
Output terminals provided at a height of 50mm above the floor level as specified in the ISO 7637-2 standard
Enhanced reproducibility
Two types of CDNs available (60 V/50 A and 60 V/100 A)
The main frame contains a built-in CDN module supporting up to 100 A, thereby allowing a large-capacity test to be conducted in a
single cabinet without using any external CDN.
Dedicated software for condition setting and tester control
JASO D001-94 pulse unit offered as an optional module
For other details such as compliance with test requirements of individual auto makers, please contact us.
2, 2, 4 P -
0 Speci cation
Model KES7702 KES7703
CDN capacity 60 VDCmax 50 Amax 60 VDCmax 100 Amax
Input voltage 100 to 240 VAC (factory-set default*) 50/60 Hz 500 VA or less
Dimensions 440(17.32”)W × 405(15.94”) H× 605(23.81”) Dmm 440(17.32”)W × 405(15.94”) H× 620(24.40”) Dmm
Weight Approx. 45 kg(99.20lbs) Approx.48 kg(105.82lbs)
PC interface RS-232C
Pulse module Plug-in type: 5 modules (250 mm wide max.) External-connect type: 2 modules
Others
Analog control terminal for the DC power supply for EUT, Monitor terminal (100:1),
External stop terminal, Warning lamp terminal (24VDC, 500mA max), Emergency stop switch
*Input voltage, 100, 110, 115, 120, 200, 220, 230, and 240 VAC available as factory option.
3. 3
DC cut time can be set within a range of 2 ms to 200 ms.
Since it also outputs positive polarity waveforms whose polarity has been reversed, it supports not only ISO standards but also independent standards of automobile manufacturers as well.
Output impedance Since 2Ω, 4Ω, and 10Ω can be selected, it supports not only ISO standards but also independent standards of automobile manufacturers as well.
DC cut time can be set within a range of 1 ms to 200 ms.
Since it also outputs positive polarity waveforms whose polarity has been reversed, it supports not only ISO standards but also independent standards of automobile manufacturers as well.
Output impedance Since 20 Ω and 50 Ω can be selected, it supports ISO7637-2.2004 standards and SAE J1113 standards.
KES7711A, KES7713B/7714 - Pulse1-12V, Pulse1-24V
KES7711A, KES7713B and KES7714 generate test
pulses 1 required by the ISO and SAE standards. Test
pulse 1 is used to simulate the transient phenomenon
that occurs when the power supply is cut off from the
inductive load.
Pulse2a
Pulse3a
Pulse1-12 Pulse1-24
Pulse3b
2, 0 6 7 S
0 Speci cation
Model KES7711A
Pulse unit 1 Plug-in type
Peak voltage (Us) ±20 V to ±150 V, in steps of 0.1 V
Output impedance (Ri) 2 Ω 4 Ω 10 Ω
Rise time (tr) 1 µs (+0 µs, -0.5 µs)
Pulse width (td)
CDN output :
2000 µs ±400 µs at No Load, 1500 µs ±300 µs at 10 Ω Load
1000 µs ±200 µs at 4 Ω Load, 600 µs ±120 µs at 2 Ω Load
PLUSEOUT output :
200 µs to 500 µs at No Load (fixed value)
Repetition interval (t1)
CDN output : 0.5 s to 99 s, in steps of 0.1 s,
PLUSEOUT output : 0.2 s to 99 s, in steps of 0.1 s
DC cut time (t2)
CDN output : 2 ms to 200 ms, in steps of 0.1 ms
PLUSEOUT output : 0 ms
Surge delay time (t3) Less than 100 µs
CDN capacity –
Driving power Supplied from the main frame
Power consumption –
Dimensions 50(1.96”)W × 260(10.23”)H × 330(12.99”)D mm
Weight Approx. 2.7 kg(5.95lbs)
2, 2, 0 6 7 S
0 Speci cation
Model KES7713B KES7714
Pulse unit 1 External-connect type
Peak voltage (Us) ±20 V to ±700 V, in steps of 0.1 V
Output impedance (Ri) 20 Ω(SAE) 50 Ω(ISO)
Rise time (tr) 1 µs (+0 µs, -0.5 µs)(SAE) 3 µs (+0 µs, -1.5 µs)(ISO)
Pulse width (td) 1000 µs ± 200 µs at No Load / 50 Ω Load
Repetition interval (t1) 0.5 s to 99 s, in steps of 0.1 s
DC cut time (t2) 1 ms to 200 ms, in steps of 0.1 ms
Surge delay time (t3) Less than 100 µs
CDN capacity 60VDCmax 50Amax 60VDCmax 100Amax
Driving power 100 VAC to 240 VAC 50/60 Hz
Power consumption 200 VA
Dimensions 440(17.32”)W×280(11.02”)H×595(23.42”)D mm
Weight Approx. 40 kg(88.18lbs) Approx. 42 kg(92.59lbs)
4. 4
Output impedance Since 2Ω, 4Ω, and 10Ω can be selected, it supports ISO7637-2.2004SO standards and independent standards of automobile manufacturers.
Since it also outputs negative polarity waveforms whose polarity has been reversed, it supports ISO7637-3.2007 standards and independent standards of automobile manufacturers.
Recurrence interval frequency sweeps (1 kHz to 100 kHz) can be performed. Four modes are available for sweeps.
KES7721- Pulse2a
KES7731- Pulse3a/3b
The KES7721 generate test pulses 2a required by the ISO and SAE
standards. Test pulse 2a is used to simulate the transient phenomenon
where induction occurs in the wire harness when the current flowing in
the device connected in parallel to the tested device is suddenly cut off.
The KES7731 generate test pulses 3a/3b required by the ISO and SAE
standards. Test pulses 3a/3b are used to simulate the transient phenomenon
that occurs during the switching process.
2, 0 6 7 S I 0 6 - 7 S I
0 Speci cation
Model KES7731
Pulse module 3a/3b Plug-in type
Peak voltage (Us) ±20 V to ± 300 V, in steps of 0.1 V
Output impedance (Ri) 50 Ω
Rise time (tr) 5 ns ±1.5 ns
Pulse width (td) 150 ns ±45 ns at No Load / 50 Ω Load
Repetition interval (t1)
(Frequency)
1 to 100 kHz, in steps of 1 kHz
Generation time (t4) 10 ms
Pulse train interval (t5) 90 ms to 9.99 s, in steps of 0.1 ms
Driving power Supplied from the main frame
Power consumption –
Dimensions 50(1.96”)W × 260(10.23”)H × 330(12.99”)D mm
Weight Approx. 2.1 kg(4.62lbs)
2, 0 6 7 S ISO7637-3 Slow Pulses
0 Speci cation
Model KES7721
Pulse module 2a Plug-in type
Peak voltage (Us) ±20 V to ± 300 V, in steps of 0.1 V
Output impedance (Ri) 2 Ω 4 Ω 10 Ω
Rise time (tr) 1 µs (+0 µs, −0.5 µs)
Pulse width (td) 50 µs ±10 µs at No Load, 40 µs ± 8.0 µs at 4 Ω Load, 12 µs ± 2.4 µs at 2 Ω Load
Repetition interval (t1) 0.2 s to 99 s, in steps of 0.1 s
DC cut time (t2) 1 ms to 100 ms, in steps of 0.1 ms
Surge delay time (t3) Less than 100 µs
Driving power Supplied from the main frame
Power consumption –
Dimensions 50(1.96”)W × 260(10.23”)H × 330(12.99”)D mm
Weight Approx. 2.5 kg(5.51lbs)
5. 5
KES7750/7751- Pulse5a/5b
SPEC80677/80678- Pulse 5b Load Dump Suppressor
The KES7750, KES7751 generates test pulses 5a/5b required by the ISO and
SAE standards. Test pulses 5a/5b are used to simulate the transient voltage
that is produced when the battery is cut off from the operating alternator. An
alternator having a transient voltage suppressor is tested with test pulse 5b,
while test pulse 5a is used to test one that does not have such a suppressor.
Pulse5a
10%
90%
t
td
tr
Ua
0V
Us
ISO21848 Overvoltages
10%
90%
t
ts tf
tr
Ua
Umax
0V
Pulse5b
Pulse5a ISO21848 Overvoltages
Features
Suppressed voltage: 100 V max. (settable in steps of 0.1 V)
The waveform required by the standard can be output accurately without changing the pulse width (td) that is set for pulse 5a.
*The above applies only when Kikusui’s pulse 5a/5b module (KES7750) or an amplifier circuit-based pulse 5a generator is used.
The SPEC80677/80678 are suppressors that generates pulse 5b
required by ISO 7637-2.2004, ISO16750-2.2010 standard. When
connected with the pulse 5a/5b module (KES7750), it lets you set a
suppressed voltage of up to 100 V in steps of 0.1 V.
7, 0 6 0 6 7 S I
0 Speci cation
Model SPEC80677 SPEC80678
Load dump suppressor for generating pulse 5b External-connect type
CDN capacity 60VDCmax 50Amax 60VDCmax 100Amax
Maximum input surge voltage (Us) 200 V Max
Settable suppressed voltage range (Us*) 10 to 100 V, in steps of 0.1 V / accuracy:3.0 V
Maximum suction surge current 300A Max
Maximum suction surge interval 30 s or more
Driving power 100VAC to 240VAC 50/60Hz
Power consumption 90VA or less
Dimensions 440(17.32”)W×133(5.23”)H×550(21.65”)D mm
Weight Approx. 17kg(37.47lbs)
2, 2, 0 6 0 6 7 S I
0 Speci cation
Model KES7750 KES7751
Pulse module 5a/5b External-connect type
Peak voltage (Us) +40.0V to +200.0V(0.1 V step), +40.0V to +150.0V (Output impedance (Ri) 0.5Ω)
Output impedance (Ri) 0.5Ω, 1Ω, 2Ω, 4Ω, 6Ω, 8Ω
Rise time (tr) 10 ms (+0ms, -5ms)
Pulse width (td)
Choose from 40ms, 50ms, 100ms, 150ms, 200ms, 250ms, 300ms, 350ms,
400ms, 450ms, 500ms, 550ms, 600ms, 650ms, 700ms
Repetition interval (t1) 30.0 s to 99.0 s (0.1 s step) *Ua Us 100V : 60.0 s to 99.0 s (0.1 s step)
CDN capacity 60VDC max 50A max 60VDC max 100A max
Driving power Supplied from the main frame
Power consumption –
Dimensions 440(17.32”)W×280(11.02”)H×595(23.42”)D mm 440(17.32”)W×280(11.02”)H×610(24.01”)D mm
Weight Approx. 32 kg(70.54lbs) Approx. 35 kg(77.16lbs)
ISO21848 Overvoltages(DC-10615 Load Dump)mode
Peak voltage(Umax) 40.0V to 120.0V 0.1 V step
Output impedance (Ri) 0.5Ω, 1Ω, 2Ω, 4Ω, 6Ω, 8Ω
Rise time (tr) 10ms
Control time(ts) 400ms
Fall time (tr) 20ms
6. 6
1-12V BP Module
2a BP Module
3a/3b Module
SPEC80184 : PulseA2/12V system
SPEC80185 : PulseB1/12V system
SPEC80186 : PulseB2/12V system
SPEC80183
PulseA1/12V system
Plug-in type
JASO D001 module
External-connect type
JASO D001 module
SPEC80188 :PulseD2/24V system
SPEC80189 :PulseE/24V system
SPEC80187
PulseD1/24V series
Plug-in type
JASO D001 module
External-connect type
JASO D001 module
KES7702/KES7703
main frame
External-connect type
ISO 7637 module
External-connect type
ISO 7637 module
KES7711A:Pulse1-12V BP
KES7721 :Pulse2a BP
KES7731 :Pulse3a/3b
KES7750/KES7751:Pulse5a/5b
SPEC80677/SPEC80678:
Pulse5b Load Dump Suppressor
KES7713B/KES7714:Pulse1-24V BP
Plug-in type
ISO 7637 module
PULSE 2a BP Module
PULSE 1-12V BPModule PULSE 3a/3b Module
PULSE 1-12V BP Module PULSE 1-12V BP Module
PULSE 1-12V BP Module PULSE 1-12V BPModule PULSE 1-12V BPModule
Height:50mm
SG section
Output terminal
Pulse output bar
Grand plain
Placing the output system on the front surface and the
power supply system and signal system on the rear
surface made it possible to achieve stable transient surge
output and communication control. Also, a bus bar was
utilized for the output end. Since the input and communi-
cation control systems of each unit are separated from the
output lines, malfunction of the tester itself due to
transient surges being output is less likely to occur.
1.System components
The KES7702/KES7703 main frame can be connected with up to 7 pulse modules (5 plug-in type modules + 2 external-connect type modules).
By replacing pulse modules, it is possible to comply with various automotive manufacturer’s requirements, such as the ISO 7637-2 and JASO
D001 standards.
2.Test reproducibility improvement
The KES7702/KES7703 mainframe are designed to simplify the setup of the test environment prescribed in the ISO7637-2 standards.
Preparation of the test environment can lead to test reproducibility.
Since the lower part of mainframe KES7702/KES7703
testers is an SG unit, braided wire and other ground
cables are unnecessary as a connection with a ground
plane can be made.Also, the output terminal is set at a
height of 50 mm from the ground plane (reference
ground surface) as prescribed in the ISO7637-2
standards.
Output waveform stability
Test reproducibility
*In the KES7700 series, each pulse module supports a specific surge waveform. If the related international standard is revised, the system can be upgraded simply by replacing pulse
modules. This system architecture also makes it easy to meet individual auto makers’ test requirements.
8. 8
SPEC80183 JASO D001-94 Pulse A1/12V
Speci cation
Pulse module A1 External-connect type
Peak voltage(Us)/Damping constant/output resistance(R3) 100V, in steps of 0.1 V/200mS/0.8Ω
Rise time (tr) 1µs or less
Repetition interval (t1) 30.0s 99s, in steps of 0.1s
Dimensions 440(17.32”)W × 280(11.02”)H × 580(22.83”)D mm
Weight Approx. 30kg(66.13lbs)
SPEC80184 JASO D001-94 Pulse A2/24V
Speci cation
Pulse module A2 Plug-in type
Peak voltage(Us)/Damping constant/output resistance(R3) 150V, in steps of 0.1 V/2.5µs/0.4Ω
Rise time (tr) 1µs or less
Repetition interval (t1) 5.0s 99s, in steps of 0.1s
Dimensions 50(1.96”)W × 260(10.23”)H × 330(12.99”)D mm
Weight Approx. 3kg(6.61lbs)
SPEC80185 JASO D001-94 Pulse B1/B12V
Speci cation
Pulse module B1 Plug-in type
Peak voltage(Us)/Damping constant/output resistance(R3)/DC cut time -100V, in steps of 0.1 V/60ms/8Ω/300ms
Rise time (tr) 1µs or less
Repetition interval (t1) 10.0s 99s, in steps of 0.1s
Dimensions 50(1.96”)W × 260(10.23”)H × 330(12.99”)D mm
Weight Approx. 3.5kg(7.71lbs)
SPEC80186 JASO D001-94 Pulse B2/B12V
Speci cation
Pulse module B2 Plug-in type
Peak voltage(Us)/Damping constant/output resistance(R3)/DC cut time -290V, in steps of 0.1 V/2ms/80Ω/10ms
Rise time (tr) 1µs or less
Repetition interval (t1) 5.0s 99s, in steps of 0.1s
Dimensions 50(1.96”)W × 260(10.23”)H × 330(12.99”)D mm
Weight Approx. 2.5kg(5.51lbs)
SPEC80187 JASO D001-94 Pulse D1/24V
Speci cation
Pulse module D1 External-connect type
Peak voltage(Us)/Damping constant/output resistance(R3) 150V, in steps of 0.1 V/400ms/1.5Ω
Rise time (tr) 1µs or less
Repetition interval (t1) 30.0s 99s, in steps of 0.1s
Dimensions 440(17.32”)W × 280(11.02”)H × 580(22.83”)D mm
Weight Approx. 30kg(66.13lbs)
SPEC80188 JASO D001-94 Pulse D2/24V
Speci cation
Pulse module D2 Plug-in type
Peak voltage(Us)/Damping constant/output resistance(R3) 200V, in steps of 0.1 V/2.5µS/0.9Ω
Rise time (tr) 1µs or less
Repetition interval (t1) 5.0s 99s, in steps of 0.1s
Dimensions 50(1.96”)W × 260(10.23”)H × 330(12.99”)D mm
Weight Approx. 2.5kg(5.51lbs)
SPEC80189 JASO D001-94 Pulse E/24V
Speci cation
Pulse module E Plug-in type
Peak voltage(Us)/Damping constant/output resistance(R3)/DC cut time 340V, in steps of 0.1 V/26ms/210Ω/130ms
Rise time (tr) 1µs or less
Repetition interval (t1) 30.0s 99s, in steps of 0.1s
Dimensions 50(1.96”)W × 260(10.23”)H × 330(12.99”)D mm
Weight Approx. 3.5kg(7.71lbs)
JASO standards are automotive standards established by the Society of
Automotive Engineers of Japan. For environment tests, "D001: General Rules
of Environmental Testing Methods for Automotive Electronic Equipment"
is most generally utilized. Pulse units for performing "transient voltage
characteristics tests" in this standard are available as an option. This pulse
unit can perform tests conforming to JASO D001 standards by connecting to
mainframe KES7702/KES7703 testers.
Replacing a pulse unit makes it easy to comply with JASO standards. Recurrence interval Settings from a minimum of 5.0s are possible.
Varies by pulse unit. Refer to the specifications shown below.
10. 10
KES7400A Series - Voltage Variation Simulator
The voltage variation simulator KES7400A series comes
in a single cabinet that consists of a Signal Generator (SG)
module (including an arbitrary pulse generator), which
combines Kikusui Electronics Corp.’s power supply
technology and EMC technology, and a high-speed bipolar
power supply module. Many automotive electronic devices
have long wire harnesses and inductive load characteristics,
as do motors, or capacitive load characteristics with a
large-capacity capacitor connected between the input and
ground. In the case of these devices, general DC power
supplies exceed the linear operation range, potentially
making it impossible to obtain the desired waveform output.
Considering this problem, it is common to use a bipolar
power supply for automotive EMC testing.
In order to generate the reprodution of variation occurrence
used by the actual automobile, the synchronized output is
also possible up to 4ch such as ACC, IG1(or IG2), and ILL
besides the connection to the +B (Battery line)
Complied to ISO7637-2.2004
The tester is capable of catering to individual auto makers’ test requirements (except for extremely rare ones).
Bipolar power supply supporting a maximum range of ±60 V at ±50 A
Four models are available with power capacities of 12.5, 25.0, 37.5, and 50.0 A, respectively. 100 A or 200 A power supply can be
offered on request.
Synchronized operation error: 1µs or less
The frequency response is 100 kHz (full voltage swing of ±60 V, no load)
The main unit of the power supply contains an arbitrary pulse generator. * Application software KES7100 is required.
Because there is an arbitrary waveform generator installed inside the main unit, there is no complicated wiring and little test
preparation time required.
The tester can have a switch module built-in (factory option).
0 6 7 S I
Speci cation
Peak current (Us) 60 V max. (±10%), in steps of 0.1 V *1
Pulse width (td) 200 to 2000 ms (±10% ±1 ms), in steps of 1 ms *
Supply voltage fall time (t12) 1ms (±50%) *1
Pulse rise time (tr) 1ms (±50%) *1
Pulse generation delay time (t6) 1ms (±50%) *1
Output resistance 0.02 Ω or less *2
Others The output waveform rises and falls in a linear manner. *1
*1 No load on the output terminal of the power supply
*2 Comparison between the resistance with no load on the output terminal and that with a load on the output terminal
* Application software KES7100 is required.
0 6 7 S
Speci cation
Fall voltage (Ua) 60 V max. (±10%), in steps of 0.1 V *1
Fall voltage (Us) 60 V max. (±10%), in steps of 0.1 V *1
Constant voltage (UB) 60 V max. (±10%), in steps of 0.1 V *1
Fall time (t10) 1 to 100 ms (±10%), in steps of 1 ms *1
Rise time (t8, t11) 1 to 100 ms (±10%), in steps of 1 ms *1
Fall period (t7, t9) 1 to 100 ms (±10%), in steps of 1 ms *1
Output resistance 0.02 Ω or less *2
Others The output waveform rises and falls in a linear manner. *1
*1 No load on the output terminal of the power supply (Vs > Va)
*2 Comparison between the resistance with no load on the output terminal and that with a load on the output terminal
* Application software KES7100 is required.
11. 11
KES7400A Series Line Up
The KES7400A series enables Test Pulse 2b/Test Pulse 4 simulations and arbitrary waveform creations which are requirements
of the ISO 7637-2.2004 standard. Test Pulse 2b is used to simulate the transient phenomenon that derives from the DC motor that
serves as an engine after the ignition switch is turned off. Test Pulse 4 is used to simulate drops in the power supply voltage that
occurs upon activation of the starter motor serving as the internal combustion engine. The arbitrary waveform generation function
enables complex power supply voltage variation patterns to be created with ease. * Application software KES7100 is required.
2, P 7 S I 7 S IP
0 Lineup
MODEL KES7400A (KES7410A) *1 KES7401A (KES7411A) *1 KES7402A (KES7412A) *1 KES7403A (KES7413A) *1
6
Output voltage/current ±60 V ±12.5 A ±60 V ±25 A ±60 V ±37.5 A ±60 V ±50 A
Peak current ±25 A (20 ms) ±50 A (20 ms) ±75 A (20 ms) ±100 A (20 ms)
Output mode CV
Frequency response DC to 100 kHz: ±60V at no load, –3dB
Small-amplitude frequency
response (reference value)
DC to 300 kHz: ±10V at no load, –3dB
Internal resistance 10mΩ or less
Power/load variation 0.05% + 40 mV
Ripple noise 40mVrms/100mVpp or less (at no load, factory-set default)
Rise/fall time 1 µs or less (square wave 60 V)
Signal source (internal signal source)
Built-in waveform (fixed) ISO 7637 TEST PULSE 2b, TEST PULSE 4
Built-in waveform (arbitrary) Line, sine waveform, square waveform, sine sweep, square sweep, etc.
Resolution (arbitrary) Choose from 5 values, 100 µs, 1 ms, 10 ms, 100 ms, and 1000 ms.
Frequency setting range (arbitrary) 1Hz to 500Hz
Memory length (arbitrary) 16bit 64kword
Signal source (external signal input)
Frequency range DC to 300 kHz
Gain Up to 60 V of gain can be controlled with × 6 (±10 V), × 12 (±6 V)voltage.
Input impedance 10 k or less
6 O
I/F RS232C
Monitor Voltage monitor
Synchronous operation error ±1 µs or less
Driving power AC200 V 50/60 Hz (single phase)
Power consumption 2 kVA or less 4 kVA or less 6 kVA or less 8 kVA or less
Operating temperature range +5˚C to +35˚C
Operating humidity range 30% to 85%rh (dew condensation not allowed)
Storage temperature range 0˚C to +40˚C
Storage humidity range 30% to 85%rh (dew condensation not allowed)
Dimensions
440(17.32”)W×740(29.11”)H
×610(24.01”)D mm
440(17.32”)W×1010(39.76”)H
×610(24.01”)D mm
440(17.32”)W×1140(44.88”)H
×610(24.01”)D mm
440(17.32”)W×1275(50.19”)H
×610(24.01”)D mm
Weight Approx. 85 kg(187.39lbs) Approx. 120 kg(264.55lbs) Approx. 155 kg(341.71lbs) Approx. 190 kg(418.87lbs)
Protection function Overheat, overcurrent, and overvoltage protection functions are available.
Emergency stop switch A red mushroom-shaped button switch is provided.
*1 Shown in parentheses is the name of the model including the optional switch module.
12. 12
Circuit disconnection switch
Switch voltage and current
Switch ON time
Switch OFF time
Disconnection modes
2 electrodes (anode and cathode)
60 VDC max./The current value depends on the current capacity of the model in use.
1 µs or less at 1kΩ load
1 µs or less at 1kΩ load
anode mode (S1) , cathode mode (S2) , two-electrode mode(S1 and S2 simultaneous)
V
t
V
t
IN
S1
S2
+
- -
+
OUT
tr,tf<1μs
90%
90%
10%
10%
By making use of the KES7100 application software, KES7400A Series supply voltage variation testers can perform tests such as Test Pulse 4 and
Test Pulse 2b, as required by ISO7637-2 standards, as well as supply voltage variation tests required individually by automobile manufacturers. A
supply voltage variation waveform library has been prepared for the KES7100. Also, it is possible to edit the parameters that form the waveforms,
such as voltage and variation time of waveform data. When the arbitrary waveform edit function is used, complicated supply voltage variation
waveforms can easily be created as well. Moreover, when analog signals are input, the instrument can also be used as an amplifier. The model and
number of units can be selected and the system configured in accordance with the specifications of the customer's test specimen.
The KES7400A Series may contain a switch module that is available as a factory option. This switch module simulates an instantaneous power
cut due to poor contact or other factor that may arise in an automotive electronic device connected to the wire harness. There are three disconnec-
tion modes that can be selected (anode mode, cathode mode, and two-electrode mode). Power can be disconnected by turning on or off either the
anode (S1) or cathode (S2) switch or both.
1.System components
2. High-speed disconnection switch module
13. 13
① Gain characteristics
When there is no load ±60V swing and ±10V swing, almost flat gain characteristics are shown up to 100 kHz.The frequency at -3 dB also reaches
300 kHz. The linearity of gain characteristics within the specifications range is related to test reproducibility and compliance with the standards of
automobile manufacturers.
According to ISO7637-2 standards, the internal impedance of the
power supply used in testing is specified as "10 mΩ or less" at DC -
400 Hz. The same standard also specifies "0Ω to 0.05Ω" with Pulse 2b
and "0Ω to 0.02Ω" with Pulse 4.
The response speed with a rise/fall time of "1 µs or less" will conform
to tests such as momentary voltage drop tests and operation tests of
relays required by each automobile manufacturer.
A power supply ripple noise of "100 mVp-p or less" will be compatible
with minimal voltage step variability required by automobile manufac-
turers.
3 mΩ or less at DC - 400 Hz.
5.KES7400A series data
0
010
0.020
0.030
040
0 100 200 300 400
10000 100000 10000
周波数[Hz]
-
-1
-9
0
-3dB
The supply voltage variation tester that meets these conditions is the "KES7400A Series."
Conditions of selecting the Voltage variation tester
Broadband gain characteristics (sine wave) with no load ±60V swing Broadband gain characteristics (sine wave) with no load ±10V swing
Impedance characteristics
Rise/fall time: 1 µs or less Power supply ripple noise: 100 mVp-p or less
14. 14
KES7100 - Application Software for KES7000 system
The application software KES7100 for the KES7000 system
enables to control the KES7700 series and KES7400A series on
the same platform. Test conditions for transient surge tests,
voltage variations tests, and tests catering to individual
automotive manufacturer’s test requirements can be edited easily
Features
Up to 50 test conditions can be registered in a test execution list, and tests are carried out in accordance with the list.
The test editing window allows user-defined test conditions to be registered in a database in advance.
For transient surge testing, up to seven types of pulse modules can be controlled.
For voltage variations testing, up to four testers can be controlled for synchronous operation by communicating
with a single tester.
In addition to those compliant with the ISO 7637-2.2004 standard, a variety of waveforms can be generated
easily (for voltage variations testing).
Besides the tests using ISO 7637-2.2004-compliant waveform libraries, tests catering to individual auto makers’ test requirements
can be conducted with ease by using the arbitrary waveform generation function and adding necessary waveform libraries. For
information about the supported standards, please contact us.
The created test execution list can be saved in a file along with comments.
A separate test execution list can be created for each type of device to be tested.
The result of the OK/NG judgment that the user makes at the end of each test can be saved in the execution list.
A test record report (CSV-format file) can be created for each test registered in the execution list. (These reports can be viewed and
edited using spreadsheet software.)
The RS-232C interface is supported for communication.
2, Application Software
0 Speci cation
Test settings
Transient surge test: ISO 7637-2 Pulse 1-12V, Pulse 1-24V, Pulse 2a, Pulse 3a/3b, Pulse 5a/5b
Transient surge test: JASO D001 Pulse A1, Pulse A2, Pulse B1, Pulse B2, Pulse D1, Pulse D2, Pulse E
Voltage variations test: ISO 7637-2 Pulse 2b, Pulse 4, arbitrary waveform generation, waveform libraries catering to
individual auto makers’ test requirements * Option
Others Test report creation function (CSV file format), external trigger input/output function (TTL signal level) * Special order only
PC specs
OS Microsoft Windows, XP
CPU Pentium II 400 MHz or faster
RAM 64 MB or more
HDD 100 MB or more of free space
Display SVGA 1024 × 768 or more
Communication port RS232C*
by using waveform libraries. Also, the arbitrary waveform
generation function makes it possible to create various voltage
variation waveforms. Furthermore, KES7100 enables to save
user-created reports in CSV files.
*2 ports are required when both transient immunity tester and voltage variation simulator are performed. The communication cable for RS232C is required for each port. It can not
be controlled simultaneously. The RS232C communication cable (1pc.) is included as a standard accessory.
15. 15
This waveform library is for transient surge testing. By default, it contains the waveforms specified by the ISO 7637-2 and JASO D001 standards.
This waveform library is for voltage variations testing. By default, it contains the Pulse 2b and Pulse 4 waveforms specified by the ISO 7637-2 standard.
A variety of waveforms can be generated by combining waveform parts.
Mode (AMP/SW)
Line (increase/decrease)
Sine wave (phase 0˚/180˚)
Square wave (phase 0˚/180˚)
Sine wave sweep (phase 0˚/180˚)
Square wave sweep (phase 0˚/180˚)
Exponential curve (decrease/increase)
Semi-sine wave (phase 0˚/180˚)
Chopping wave (phase 0˚/180˚)
Vertical line (increase/increase)
Horizontal line / Sine wave (1/4 phase)
For voltage variation waveforms required by auto
makers, pattern libraries are available (charged).
Complex requirements like the values of V (voltage)
and T (variable time) are varied in steps can be
optionally added.
(An estimate is to be made through consultation.)
KES7100 Arbitrary Waveform Generation Function
KES7100 Transient Surge Test
KES7100 Voltage Variations Test
KES7100 Auto Maker-Specific Waveform Library (Example)
16. ■ All products contained in this catalogue are equipment and devices that are premised on use under the
supervision of qualified personnel, and are not designed or produced for home-use or use by general
consumers. ■ Specifications, design and so forth are subject to change without prior notice to improve the
quality. ■ Product names and prices are subject to change and production may be discontinued when
necessary. ■ Product names, company names and brand names contained in this catalogue represent the
respective registered trade name or trade mark. ■ Colors, textures and so forth of photographs shown in this
catalogue may differ from actual products due to a limited fidelity in printing. ■ Although every effort has been
made to provide the information as accurate as possible for this catalogue, certain details have unavoidably
been omitted due to limitations in space. ■ If you find any misprints or errors in this catalogue, it would be
appreciated if you would inform us. ■ Please contact our distributors to confirm specifications, price,
accessories or anything that may be unclear when placing an order or concluding a purchasing agreement.
●Distributor:
Printed in Japan Issue: Dec. 2011 201112PDFEC21
www.kikusui.cn
Room 216,Building 4,No.641,Tianshan Road,ShanghaiCity,China
Phone : 021-5887-9067 Facsimile : 021-5887-9069
2975 Bowers Avenue Suite 307 Santa Clara CA
Phone : 408-980-9433 Facsimile : 408-980-9409
www.kikusuiamerica.com
1-877-876-2807