The document provides instructions for installing a self-adhesive smart switchable film, noting that the glass surface should be clean and dry, the film should be 2-3mm smaller than the glass, and the film's electrodes should not contact any metal. It lists the required tools and gives an 11-step process for applying the film, which involves cleaning the glass, peeling the protective covering, adhering the film while removing bubbles, connecting the wires, testing functionality, and covering the edges.

1. 自贴型调光膜安装指导
安装所需工具
- 自贴型调光膜（下称 自贴膜）
- 无尘纸
- IPA
- 软布
- 线材
- 塑料刮刀 / 滚筒
- 剪线钳 / 剪刀
- 条形塑料外壳 / 透明胶带
注意事项
- 自贴膜是应用静电吸附原理贴附于玻璃表面，请确定玻璃表面不要有水存在。
- 建议自贴膜的尺寸比玻璃实际尺寸小 2-3mm.
- 自贴膜的电极不能接触到金属边框或其他导电的外壳。
安装指导
1. 将自贴膜从纸筒内拿出，平放在干净平整的地方。
2. 找到有粘性的一面（有标识），向上。
3. 清洁玻璃，去除玻璃表面的残留物，保证玻璃平滑。
4. 用无尘布、IPA 清洁玻璃，待 IPA 挥发后可以准备贴膜。
5. 揭掉粘性面顶边约 150mm 的保护膜。注意要在干净的环境中操作。
6. 将自贴膜已撕下保护膜的顶边轻轻对准粘帖上去，然后再逐步向下轻拉保护
膜，边揭保护膜自贴膜会自己吸附上去；另一手拿塑料刮刀/滚筒由左向右水
平移动，从而把当中的气泡赶出来。
7. 把自贴膜当中及边缘的气泡完全赶尽。
8. 自贴膜一共有两个电极：将电源适配器出来的线分别与两个电极接好，由于
采用交流电故无正负之分。
9. 测试可以正常工作（通电透明，断电不透明）后需要用胶带将电极覆盖，最
好再用一个塑料不导电的外壳将其遮住。
10. 建议用透明胶带将自贴膜的其余三边粘帖覆盖，以防清洁时造成不必要的损
伤。
11. 日程请使用 IPA 进行清洁，注意清洁前确认拔掉电源插头。
Guangzhou Huichi Glass Technical Co, Ltd
Website: http://www.huichiglass.com
Contact: Mukial@huichiglass.com mukialzhang@gmail.com Tel:+8618922173106

2. Self Adhesive Smart Switchable Film Installation Guide
Tools required
- Self adhesive smart switchable film
- Clean paper
- IPA
- Soft cloth
- Wires
- Plastic scraper / roller
- Wire cutters / scissors
- Plastic cover / clear tape
Please note
- The self adhesive film is a dry install application. Make sure there is no water on
the glass surface.
- We recommend the outer dimensions of the self adhesive film are 2 - 3 mm
shorter than the visual area of the glass.
- The bus bar should never come into contact with any metal frame or other
conductive materials.
Installation
1. Clean the glass with a soft dry cloth until the surface is completely clean. And to
make sure the surface is dry, you might use IPA while cleaning.
2. Peel the protective cover (there is one side with stickiness) and stick the film on
the glass. It would be a same way as you stick the guard film for you mobile
phone or ipad.
3. And please note the bus bar should never come into contact with any metal
frame or trim. You could use a plastic cover to prevent the bus bar edge exposed.
4. At last we advise using a cover trim (clear tape is also available) on all the four
edges of the film and clean it with IPA and soft cloth.