GEAR PULLER - ARM-Layout1
•
0 likes•125 views
This technical drawing shows dimensions for a gear puller arm with various radii, lengths, angles, and notes. Key specifications include lengths of 2.8750, 2.8400, and 1.1250 inches, an angle of 25 degrees, radii of 0.4060 and 0.0300 inches, and notes to fillet all edges but not both sides of a specific dimension. The drawing was created by K. Thorpe on November 19, 2014 for Central Carolina Technical College's engineering graphics technology course.
Report
Share
Report
Share
Download to read offline
Recommended
GEAR PULLY - LEAD SCREW-Layout1
This technical drawing shows a gear puller with lead screw details. It includes dimensions for the gear puller components and lead screw, a scale of 1:1, and was drawn by K. Thorpe on November 18, 2014. It also references a detail view A of the lead screw at a scale of 4:1 and provides file information for the technical drawing.
GEAR PULLER - COTTER PIN-Layout1
This drawing shows a gear puller tool used to remove cotter pins. It was drawn by K. Thorpe on November 20, 2014 at a scale of 8:1. The gear puller has several rounded features including the jaws that grip the gear, with dimensions provided in inches. It will be used to assist the removal of cotter pins from mechanical components.
GEAR PULLY - CLEVIS PIN-Layout1
The drawing depicts a gear puller with clevis pin attachment. It shows the dimensions and specifications for the gear puller's clevis pin connection point, including diameters of 0.4380 and 0.3100 inches, a 0.0300 inch by 45 degree chamfer, and 0.0940 inch diameter pin hole. The drawing also lists the date of November 20, 2014, was drawn by K. Thorpe and checked by the engineering graphics technology department at Central Carolina Technical College.
Notam2
NOTAMs provide information on aviation hazards and include up to 8 items identified by letters. This NOTAM describes airspace restrictions over Turkey that are in effect from March 23-27 and March 31-April 22 from 0530-1430 daily. The restricted airspace is within a 5nm radius of coordinates 4123N 03137E at altitudes between 4500ft and 6000ft above sea level.
PLUG VALVE - HOUSING-Layout1
This drawing shows the housing component of a plug valve. It includes dimensions for the outer diameter, holes, and ribs. The housing has an outer diameter of 88mm and contains three evenly spaced ribs with a radius of 2mm on the interior. Smaller holes of varying diameters are placed throughout for connections. The title, scale, and other identifying information are present to specify the part and conform to engineering drawing standards.
1
This document provides information about an individual's career history including positions held from 1999-2015 at various companies such as Canon, Sharp, Kyocera, HP, Samsung, and Ricoh. It lists the roles of Manager, Team Leader, and positions abroad lasting 36, 42, and 20 months. It also outlines the individual's education including a BEP in Electronics and a TSAE certification at level III in Technician Connectivity.
sScenario2LM[1]
This document analyzes three probable weapons storage areas in Kabul, Afghanistan from imagery taken on May 14, 2010. Area A is described as having dimensions of approximately 120m wide, 150m high, and 9m wall height. It contains 20 storage containers and vehicles. Area B has dimensions of 75-95m wide, 84-132m high, and contains 50 storage crates and 13 containers. Area C is approximately 80m wide, 102m high, with a 3.5m wall, and contains storage containers and vehicles guarded by a tower.
Script 1
The script feedback provides strengths and areas for improvement in the student's script across narrative, character, and format. For narrative, the script effectively establishes the confrontation between characters but could develop the backstory more. For character, the main character is engaging but side characters lack depth. For format, the script has a clear structure but transitions between scenes could be strengthened.
Recommended
GEAR PULLY - LEAD SCREW-Layout1
This technical drawing shows a gear puller with lead screw details. It includes dimensions for the gear puller components and lead screw, a scale of 1:1, and was drawn by K. Thorpe on November 18, 2014. It also references a detail view A of the lead screw at a scale of 4:1 and provides file information for the technical drawing.
GEAR PULLER - COTTER PIN-Layout1
This drawing shows a gear puller tool used to remove cotter pins. It was drawn by K. Thorpe on November 20, 2014 at a scale of 8:1. The gear puller has several rounded features including the jaws that grip the gear, with dimensions provided in inches. It will be used to assist the removal of cotter pins from mechanical components.
GEAR PULLY - CLEVIS PIN-Layout1
The drawing depicts a gear puller with clevis pin attachment. It shows the dimensions and specifications for the gear puller's clevis pin connection point, including diameters of 0.4380 and 0.3100 inches, a 0.0300 inch by 45 degree chamfer, and 0.0940 inch diameter pin hole. The drawing also lists the date of November 20, 2014, was drawn by K. Thorpe and checked by the engineering graphics technology department at Central Carolina Technical College.
Notam2
NOTAMs provide information on aviation hazards and include up to 8 items identified by letters. This NOTAM describes airspace restrictions over Turkey that are in effect from March 23-27 and March 31-April 22 from 0530-1430 daily. The restricted airspace is within a 5nm radius of coordinates 4123N 03137E at altitudes between 4500ft and 6000ft above sea level.
PLUG VALVE - HOUSING-Layout1
This drawing shows the housing component of a plug valve. It includes dimensions for the outer diameter, holes, and ribs. The housing has an outer diameter of 88mm and contains three evenly spaced ribs with a radius of 2mm on the interior. Smaller holes of varying diameters are placed throughout for connections. The title, scale, and other identifying information are present to specify the part and conform to engineering drawing standards.
1
This document provides information about an individual's career history including positions held from 1999-2015 at various companies such as Canon, Sharp, Kyocera, HP, Samsung, and Ricoh. It lists the roles of Manager, Team Leader, and positions abroad lasting 36, 42, and 20 months. It also outlines the individual's education including a BEP in Electronics and a TSAE certification at level III in Technician Connectivity.
sScenario2LM[1]
This document analyzes three probable weapons storage areas in Kabul, Afghanistan from imagery taken on May 14, 2010. Area A is described as having dimensions of approximately 120m wide, 150m high, and 9m wall height. It contains 20 storage containers and vehicles. Area B has dimensions of 75-95m wide, 84-132m high, and contains 50 storage crates and 13 containers. Area C is approximately 80m wide, 102m high, with a 3.5m wall, and contains storage containers and vehicles guarded by a tower.
Script 1
The script feedback provides strengths and areas for improvement in the student's script across narrative, character, and format. For narrative, the script effectively establishes the confrontation between characters but could develop the backstory more. For character, the main character is engaging but side characters lack depth. For format, the script has a clear structure but transitions between scenes could be strengthened.
revit_practicing
This document contains architectural drawings for a building project including front, rear, right, and left elevations at scales of 1/16"=1" and 1/8"=1". The drawings were created on October 24, 2016 at 3:41 PM and checked by someone other than the author.
2
This document contains architectural drawings and notes for a building project. It includes four elevation drawings and two section drawings at a scale of 1:100 meters. Notes indicate the project location, relevant laws, and that the drawings are the property of the architect and cannot be duplicated without permission. Dimensioned drawings and technical details are provided for construction.
Trapezoidal Log-Periodic Antenna Analysis
Analyzing radiation pattern, S11 parameters & other important factors that define antenna performance on HFSS software. Feel free to ask any queries. Do like the post if its worthy enough.
Saudi Aramco Test Report (SATR)
This document is from Dirham Mujahid Al-Salah Est., a general contracting company based in Dammam, Saudi Arabia. It provides their contact information, including their commercial registration number and address. It also references two projects they are involved in - the East/West Pipeline Project for the Master Gas Pipeline Phase 1 Projects Division in Riyadh, with contract number 6500032833, and construction work for the Saudi Aramco Test Refinery.
Saudi Aramco Inspection Checklist (SAIC)
Dirham Mujahid Al-Salah Est. is a general contracting company based in Saudi Arabia that provides services including general building construction, road construction, mechanical, electrical maintenance and operation works. The document appears to be a Saudi Arabian inspection checklist for a gas pipeline project prepared by Dirham Mujahid Al-Salah Est. in April 2016 for their Projects Division in Riyadh.
Plan the approach based on the angiogram
Plan the approach based on the angiogram
Markus Meyer-Geßner, Düsseldorf, Germany
11th Experts Live CTO
The annual Euro CTO meeting
September 13th –14th, 2019 - Berlin, Germany
Kalibratie en scheepsgeometrie met een historisch perspectief
Het onderwerp wordt door Nicolàs de Hilster, Starmountain Survey & Consultancy, belicht. Hoe is de aandacht voor kalibratie en scheepsgeometrie in de loop van de jaren gegroeid?
One-Click CFD Users' Guide
One-Click CFD is a CFD framework based on openFoam that allows users to run aerodynamic simulations on car designs with little or no CFD experience. The document outlines the steps to use One-Click CFD, including preparing CAD geometry as STL files, starting a simulation locally or on AWS cloud, and post-processing results using the HTML report or ParaView software. The goal is to make CFD accessible to those interested in racing car aerodynamics.
Rev0 kalol
This document appears to be an electrical single line diagram for a project in Kalol, India. It includes the project title, client name, drawing number, title as a single line diagram for Kalol, and references other electrical drawings for load lists, symbols, and design review. The drawing was issued for review on March 21, 2017 by the contractor Project Limited in Mumbai, India.
Kinder Morgan's Tennessee Gas Pipeline Northeast Energy Direct Pipeline Expan...
Kinder Morgan's Tennessee Gas Pipeline Northeast Energy Direct Pipeline Expan...Marcellus Drilling News
A map showing the latest proposed route for the massive, $3.3 billion Northeast Energy Direct pipeline that would bring cheap, abundant, clean-burning Marcellus Shale gas from northeastern Pennsylvania to New England energy markets. The NED project is currently in the pre-filing stage with the Federal Energy Regulatory Commission (as of July 2015).Preventive checklist
The quarterly maintenance checklist provides instructions for technicians to clean, lubricate, and inspect various components of training machines on a quarterly basis. Technicians are to clean and lubricate slides and hydraulic tanks, check motors and gearboxes, inspect electrical panels and machine bases, restore machine functions, and check electrical systems, fuses, relays, and wires. The checklist is to be completed by technicians and signed off by maintenance and section supervisors.
Designing a synchronous binary irregular counter with counting sequence
This document describes the design of a synchronous binary irregular counter with a counting sequence of 0011, 1100, 0000, 1000, 0100. It includes a state diagram, next-state table, Karnaugh maps to simplify the logic expressions, and a logic diagram for implementation. Specifically, it covers an introduction to counters, defines a synchronous counter, shows the state diagram and next-state table, uses K-maps to minimize the logic expressions for J0-J3 and K0-K3, and provides the final logic expressions and diagram for implementation.
Support slide4
The document outlines the steps and analyses involved in a preliminary strength analysis of a topside module, including:
1. Generating quasi-static motion loads.
2. Combining static and motion loads.
3. Combining component load cases from static, motion, and combined analyses.
4. Defining module acceleration loads, transportation route design waves, and other data required for the analyses.
TROLLEY-Layout1
This technical drawing shows the side plate of a trolley, including dimensions and hole specifications. It was drawn by K. Thorpe on October 2, 2014 for Central Carolina Technical College's Engineering Graphics Technology program. The drawing is number 3 of 8 for the trolley project.
TROLLEY - WHEEL-Layout1
This drawing shows details of a trolley wheel, including dimensions and notes. It was drawn by K. Thorpe on October 30, 2014 for Central Carolina Technical College's Engineering Graphics Technology program. The drawing depicts the profile of a wheel with various radii, diameters, and other geometric specifications.
TROLLEY - SNAPS-Layout1
This technical drawing shows the dimensions for a trolley axle and wheel assembly with two snap rings to hold the axle in place and four snap rings for the wheels. It was drawn by K. Thorpe on November 5, 2014 for a class project at Central Carolina Technical College.
TROLLEY - SIDE PLATE-Layout1
This technical drawing shows the side plate component of a trolley system, including its dimensions and hole placement. It was drawn by K. Thorpe on December 8, 2014 for Central Carolina Technical College's Engineering Graphics Technology program. The side plate is approximately 8 inches long and 7 inches high with various holes and cutouts as indicated on the scale drawing.
TROLLEY - DEPARTURE BALL-Layout1
This drawing shows a departure ball bearing for a trolley with 8 evenly spaced balls. The drawing specifies the dimensions of the balls and outer raceway of the bearing which has 2 balls required and was drawn by K. Thorpe for a class project at Central Carolina Technical College.
TROLLEY - AXLE-Layout1
The drawing depicts an axle for a trolley with dimensions, including an overall length of 2.875 inches, diameter of 0.875 inches, and thickness of 0.1040 inches. It was drawn by K. Thorpe for Central Carolina Technical College's Engineering Graphics Technology course, and is drawing number 5 of 8 in the Trolley - Axle series.
TROLLEY - ASSEMBLY-Layout1
This drawing document provides assembly details for a trolley. It was drawn by K. Thorpe on December 1, 2014 at an unspecified scale for Central Carolina Technical College's Engineering Graphics Technology program. The drawing is numbered 1 of 8.
any angle clamp plug-Layout1
This technical drawing shows dimensions and specifications for a clamp plug for an any angle tool vice. It includes dimensions for various angles and diameters of the plug. The drawing also lists the date it was created, the scale, the title, associated CAD file, and the school and program where it was created.
any angle Eccentric-Layout1
This technical drawing shows dimensions for an eccentric any angle tool vice. Key dimensions include the diameter and thickness of various cylindrical and circular features ranging from .125 to 1.281 units. The drawing also lists the drafter, date, scale, title, CAD file information, and school where it was created.
More Related Content
What's hot
revit_practicing
This document contains architectural drawings for a building project including front, rear, right, and left elevations at scales of 1/16"=1" and 1/8"=1". The drawings were created on October 24, 2016 at 3:41 PM and checked by someone other than the author.
2
This document contains architectural drawings and notes for a building project. It includes four elevation drawings and two section drawings at a scale of 1:100 meters. Notes indicate the project location, relevant laws, and that the drawings are the property of the architect and cannot be duplicated without permission. Dimensioned drawings and technical details are provided for construction.
Trapezoidal Log-Periodic Antenna Analysis
Analyzing radiation pattern, S11 parameters & other important factors that define antenna performance on HFSS software. Feel free to ask any queries. Do like the post if its worthy enough.
Saudi Aramco Test Report (SATR)
This document is from Dirham Mujahid Al-Salah Est., a general contracting company based in Dammam, Saudi Arabia. It provides their contact information, including their commercial registration number and address. It also references two projects they are involved in - the East/West Pipeline Project for the Master Gas Pipeline Phase 1 Projects Division in Riyadh, with contract number 6500032833, and construction work for the Saudi Aramco Test Refinery.
Saudi Aramco Inspection Checklist (SAIC)
Dirham Mujahid Al-Salah Est. is a general contracting company based in Saudi Arabia that provides services including general building construction, road construction, mechanical, electrical maintenance and operation works. The document appears to be a Saudi Arabian inspection checklist for a gas pipeline project prepared by Dirham Mujahid Al-Salah Est. in April 2016 for their Projects Division in Riyadh.
Plan the approach based on the angiogram
Plan the approach based on the angiogram
Markus Meyer-Geßner, Düsseldorf, Germany
11th Experts Live CTO
The annual Euro CTO meeting
September 13th –14th, 2019 - Berlin, Germany
Kalibratie en scheepsgeometrie met een historisch perspectief
Het onderwerp wordt door Nicolàs de Hilster, Starmountain Survey & Consultancy, belicht. Hoe is de aandacht voor kalibratie en scheepsgeometrie in de loop van de jaren gegroeid?
One-Click CFD Users' Guide
One-Click CFD is a CFD framework based on openFoam that allows users to run aerodynamic simulations on car designs with little or no CFD experience. The document outlines the steps to use One-Click CFD, including preparing CAD geometry as STL files, starting a simulation locally or on AWS cloud, and post-processing results using the HTML report or ParaView software. The goal is to make CFD accessible to those interested in racing car aerodynamics.
Rev0 kalol
This document appears to be an electrical single line diagram for a project in Kalol, India. It includes the project title, client name, drawing number, title as a single line diagram for Kalol, and references other electrical drawings for load lists, symbols, and design review. The drawing was issued for review on March 21, 2017 by the contractor Project Limited in Mumbai, India.
Kinder Morgan's Tennessee Gas Pipeline Northeast Energy Direct Pipeline Expan...
Kinder Morgan's Tennessee Gas Pipeline Northeast Energy Direct Pipeline Expan...Marcellus Drilling News
A map showing the latest proposed route for the massive, $3.3 billion Northeast Energy Direct pipeline that would bring cheap, abundant, clean-burning Marcellus Shale gas from northeastern Pennsylvania to New England energy markets. The NED project is currently in the pre-filing stage with the Federal Energy Regulatory Commission (as of July 2015).Preventive checklist
The quarterly maintenance checklist provides instructions for technicians to clean, lubricate, and inspect various components of training machines on a quarterly basis. Technicians are to clean and lubricate slides and hydraulic tanks, check motors and gearboxes, inspect electrical panels and machine bases, restore machine functions, and check electrical systems, fuses, relays, and wires. The checklist is to be completed by technicians and signed off by maintenance and section supervisors.
Designing a synchronous binary irregular counter with counting sequence
This document describes the design of a synchronous binary irregular counter with a counting sequence of 0011, 1100, 0000, 1000, 0100. It includes a state diagram, next-state table, Karnaugh maps to simplify the logic expressions, and a logic diagram for implementation. Specifically, it covers an introduction to counters, defines a synchronous counter, shows the state diagram and next-state table, uses K-maps to minimize the logic expressions for J0-J3 and K0-K3, and provides the final logic expressions and diagram for implementation.
Support slide4
The document outlines the steps and analyses involved in a preliminary strength analysis of a topside module, including:
1. Generating quasi-static motion loads.
2. Combining static and motion loads.
3. Combining component load cases from static, motion, and combined analyses.
4. Defining module acceleration loads, transportation route design waves, and other data required for the analyses.
What's hot (13)
Kalibratie en scheepsgeometrie met een historisch perspectief
Kalibratie en scheepsgeometrie met een historisch perspectief
Kinder Morgan's Tennessee Gas Pipeline Northeast Energy Direct Pipeline Expan...
Kinder Morgan's Tennessee Gas Pipeline Northeast Energy Direct Pipeline Expan...
Designing a synchronous binary irregular counter with counting sequence
Designing a synchronous binary irregular counter with counting sequence
More from Kristopher Thorpe
TROLLEY-Layout1
This technical drawing shows the side plate of a trolley, including dimensions and hole specifications. It was drawn by K. Thorpe on October 2, 2014 for Central Carolina Technical College's Engineering Graphics Technology program. The drawing is number 3 of 8 for the trolley project.
TROLLEY - WHEEL-Layout1
This drawing shows details of a trolley wheel, including dimensions and notes. It was drawn by K. Thorpe on October 30, 2014 for Central Carolina Technical College's Engineering Graphics Technology program. The drawing depicts the profile of a wheel with various radii, diameters, and other geometric specifications.
TROLLEY - SNAPS-Layout1
This technical drawing shows the dimensions for a trolley axle and wheel assembly with two snap rings to hold the axle in place and four snap rings for the wheels. It was drawn by K. Thorpe on November 5, 2014 for a class project at Central Carolina Technical College.
TROLLEY - SIDE PLATE-Layout1
This technical drawing shows the side plate component of a trolley system, including its dimensions and hole placement. It was drawn by K. Thorpe on December 8, 2014 for Central Carolina Technical College's Engineering Graphics Technology program. The side plate is approximately 8 inches long and 7 inches high with various holes and cutouts as indicated on the scale drawing.
TROLLEY - DEPARTURE BALL-Layout1
This drawing shows a departure ball bearing for a trolley with 8 evenly spaced balls. The drawing specifies the dimensions of the balls and outer raceway of the bearing which has 2 balls required and was drawn by K. Thorpe for a class project at Central Carolina Technical College.
TROLLEY - AXLE-Layout1
The drawing depicts an axle for a trolley with dimensions, including an overall length of 2.875 inches, diameter of 0.875 inches, and thickness of 0.1040 inches. It was drawn by K. Thorpe for Central Carolina Technical College's Engineering Graphics Technology course, and is drawing number 5 of 8 in the Trolley - Axle series.
TROLLEY - ASSEMBLY-Layout1
This drawing document provides assembly details for a trolley. It was drawn by K. Thorpe on December 1, 2014 at an unspecified scale for Central Carolina Technical College's Engineering Graphics Technology program. The drawing is numbered 1 of 8.
any angle clamp plug-Layout1
This technical drawing shows dimensions and specifications for a clamp plug for an any angle tool vice. It includes dimensions for various angles and diameters of the plug. The drawing also lists the date it was created, the scale, the title, associated CAD file, and the school and program where it was created.
any angle Eccentric-Layout1
This technical drawing shows dimensions for an eccentric any angle tool vice. Key dimensions include the diameter and thickness of various cylindrical and circular features ranging from .125 to 1.281 units. The drawing also lists the drafter, date, scale, title, CAD file information, and school where it was created.
any angle lower plate-Layout1
This technical drawing shows dimensions for a lower plate of an any angle tool vice. It includes labeled dimensions for holes, radii, angles, and features of the plate. The drawing title identifies it as the lower plate of an any angle tool vice, and it was drawn by C.J. Ingram for Central Carolina Technical College's Engineering Graphics Technology program.
any angle saddle-Layout1
This drawing shows dimensions for an angle tool vice saddle, including hole diameters, radii, lengths, and labeling. Key features include dimensions ranging from 0.125 to 6.5, holes labeled with diameters and depths, fillets and rounds of 0.125 radius, and notes specifying the date, scale, title, file path and number. The drawing was created by C.J. Ingram for Central Carolina Technical College's Engineering Graphics Technology program.
any angle tool holder-Layout1
This drawing shows a compound tool holder with various dimensions and features including holes, diameters, angles, chamfers, and notes. It was drawn by C.J. Ingram for Central Carolina Technical College's Engineering Graphics Technology program and provides the details to manufacture the tool holder.
any angle upper member-Layout1
This document contains technical drawings and specifications for an upper compound member including dimensions, tolerances, notes and labels such as the title, scale, part number, date, and initials of the designer and checker. Key specifications include an outside diameter of 1.75 inches, a radius of 1.999 inches, a length of 15.1 inches, angles of 40 and 15 degrees, and thread specifications.
any angle upper plate-Layout1
This technical drawing shows dimensions for an upper plate of an any angle tool vice. It includes labeled dimensions for holes, radii, angles, and features of the plate with sizes ranging from 0.063 to 3.5 inches. The drawing also lists the date, scale, title, CAD file information, drawing number, and notes that it was drawn and checked by students at Central Carolina Technical College.
GEAR PULLY - YOKE-Layout1
This drawing shows a gear puller yoke with technical specifications. It was drawn by K. Thorpe on December 8, 2014 for Central Carolina Technical College's Engineering Graphics Technology program. The yoke has symmetrical features including rounded edges and holes, and notes specify fillet and round radii unless otherwise indicated.
GEAR PULLER - ASSEMBLY-Layout1
This drawing shows the assembly of a gear puller with 5 main parts: a yoke, arm, lead screw, clevis pin, and cotter pin. The drawing was created by K. Thorpe on 11/20/2014 for Central Carolina Technical College's Engineering Graphics Technology course. It includes the quantities needed for each of the 5 parts that make up the gear puller assembly.
PLUG VALVE - ASSEMBLEY-Layout1
This drawing document provides assembly details for a plug valve. It was drawn by K. Thorpe on December 1, 2014 at a metric scale for Central Carolina Technical College's Engineering Graphics Technology program. The drawing is numbered 1 of 6.
PLUG VALVE - HANDLE-Layout1
This technical drawing shows details of a plug valve handle. It includes dimensions for the main cylindrical handle that is 80mm long with diameters of 11mm and 9mm at each end connected by tapers with radii of 2.5mm and 1mm. Four holes with a diameter of 6mm are located around the middle section.
PLUG VALVE - PUG-Layout1
This technical drawing shows a plug valve design with dimensions. The plug valve features a cylindrical plug that fits inside a tapered valve body. Key dimensions include the plug diameter of 16mm, valve body diameters of 26.5mm and 38.5mm, and plug length of 30mm. The drawing was created by K. Thorpe for a class project at Central Carolina Technical College and checked for accuracy.
PLUG VALVE - CAP-Layout1
This drawing depicts a plug valve cap with dimensions and tolerances. It was drawn by K. Thorpe on an unspecified date for Central Carolina Technical College's Engineering Graphics Technology program. The drawing number is 2 of 6 and shows the cap has an outer diameter of 110mm, four radius 4 corners, and two M42 threads that are 2mm deep.
More from Kristopher Thorpe (20)
GEAR PULLER - ARM-Layout1
- 1. 2.8750 2.8400 1.1250 25° .4060 R.3440 R1.5000 R1.5000 9° DO NOT FILLET (BOTH SIDES) .3700 R.0300 TYP. FILLET ALL EDGES DRAWN BY: K.THORPE DATE: SCALE: 1:1 DRAWING TITLE: GEAR PULLER - ARM CCTC FILESRAPIDPHOTOGEAR PULLER - ARM.DWG 11/19/2014 DRAWING NO: 3 OF 6 SIZE: A CENTRAL CAROLINA TECHNICAL COLLEGE ENGINEERING GRAPHICS TECHNOLOGY CHECKED BY: GRADE: Ø.3125 R.4380