"Capturing Sediment on the Go, Enabling Clean Water to Flow" EZ-Flo, EZ-Catch, EZ-ClipGuard Inlet Protection: Pump-It Tube Dewatering Bags: Hi-Flo & Maxx-Flo Silt Fence: Slurry-Flo Concrete Washout Systems

1. Corydon Coppola, CPESC
President
515-577-6763
corydon@flo-water.net
www.flo-water.net

2. Standard
Dewatering Bag
The flow rate for the standard
dewatering bag is 95 gal/min/ft2
versus 192 gal/min/ft2 for the
Pump-It Tube.
Pump-It Tube enables solutions
at higher flow rates. Increasing
productivity .
The standard dewatering bags
ranging from 3x3, 6x6, 10x15, to
15x15.
Pump-It Tube vs. Standard Bag
A 15ft x 15ft dewatering bag is
replaced by a 40 inch x 20 ft
Pump-It Tube.

4. Pump-It Tubes-
Straps with D-Rings
attach around
tubes from pumps

12. Curb Inlet Protection (Clip Guard)
The Clip Guard is ideal for protecting concrete storm drains from silt and debris.
• Installs easily, just clip into place
• High Flow Grey Material allows 192 gal/ft2/min
• Reusable-After use; clean by spraying out sediment
• Also available in custom sizes
• Hydrocarbon model- incorporate polymor which solidifies hydrocarbons.
• Reusable

13. Overflow protection available on above grate models- as well.

15. EZ Inlet Guard
Flat Grate
EZ Inlet Guard
Curb Style

16. Custom Sizes available for any inlet protection

17. HiFlo/ MaxxFlo Silt Fence
HiFlo Silt fence® & MaxxFlo Silt Fence are patent pending
HiFlo & MaxxFlo Silt Fence allows better flow than standard silt fence.
• Allows better flow while keeping silt on the site
• HiFlo Grey Material allows up to 192 gal/ft2/min
• MaxxFlo Silt Fence material allows for significantly higher flow rates.
• Built in scrim for added strength
• Wood stake rolls in 50’ & 100’ lengths- Custom stake spacing and sizing
• 500’ rolls with no stakes

18. Hi Flows filter up to @ 192 gal/ft2/min
Capture sediment for safe disposal
Better Curb Appeal
Traffic Friendly
Reusable

19. Out with the half solutions, and in with the increased protection
Drivable solutions- not reducing accessibility

20. Above Grate Inlet Protection
Protect Drains and Inlets WITHOUT Lifting Any Grates
• Keeps dirt, sand, sediment, trash and debris out of drains
• Fast installation using built in magnets – no lifting of heavy catch basin grates.
• Common stocked sizes for street & combo drains . Custom sizes also available.
• Heavy-duty, reinforced material allows up to 192 gal/ft2/min. through drains.
• EZ maintenance –remove unit, shake off dirt, silt and sediment and replace.
• Low-profile design can be driven over and is unobtrusive to traffic and personnel.
• EZ Inlet Guard- awarded Product Of The Year in its division by Plant Engineering.

21. Visually Superior Solution coupled with increased performance
Easier to clean, reusable, drivable.

22. Dishonorable Discharge

23. MSD Wash Out Pit

24. “EZ- Concrete Washout System”
Treat Slurry & Release on Site EZ Concrete Washout System Steps for Proper Treatment PH Levels
Set Up Stand as Pictured above (Each bag/ Stand Should handle 3- 10 trucks)
The following steps are per concrete washout (Per truck) Stabilized
1. Sprinkle 5 lb bag of “EZ Washout PH Stabilizer” across bottom of Stand
2. Upon Starting Rinse Flow, 8 oz bottle of Solution #1 needs to be added at the rinse flow to ensure proper mixing
3. Add 8 oz bottle of Solution #2 in the same manner as step 3. (Solution 1, then Solution 2)
*Additional mixing with a few more gallons of the rinsewater will ensure adequate mixing.*
EZ Concrete Washout System Bag/ Stand will hold up to 1 cubic yard of waste. This should handle 3- 10 trucks per use.
(Dependent on amount of concrete dumped before rinsing process)