This document evaluates green propellants for use in a notional next-generation post-boost propulsion system (PBPS) for intercontinental ballistic missiles (ICBMs). It identifies candidate green propellants using an overall evaluation criterion (OEC) method accounting for toxicity, performance, and technical feasibility. Promising candidates were used to develop sized PBPS concepts, which were evaluated based on weight, cost, and technical risk. Results indicate high-test peroxide (HTP) combined with either an ethanol-based nontoxic hypergolic miscible fuel or a competitive impulse non-carcinogenic hypergol is very viable for the PBPS application due to performance and reduced toxicity over the current hydrazine-based
This was the seminar presentation on my Project report for M.Sc. Degree.
This shows basic and application of Electric propulsion.Which also shows about how electric propulsion is better than chemical propulsion.
This was the seminar presentation on my Project report for M.Sc. Degree.
This shows basic and application of Electric propulsion.Which also shows about how electric propulsion is better than chemical propulsion.
Presented to: Subgroup of the Kentucky Chemical Demilitarization Citizens’ Advisory Commission and
Chemical Destruction Community Advisory Board
Secondary Waste Working Group
Presented by:
Jeff Brubaker
ACWA Site Manager
Doug Omichinski
Systems Contractor Project Manager
Roger Thompson, CIH, CSP
Systems Contractor Safety & Health Manager
Charlie Satterwhite, CIH
Systems Contractor Senior Industrial Hygienist
Dr. John Barton
Systems Contractor Chief Scientist
Neil Frenzl
Systems Contractor Resident Engineering Manager
Piroxicam Nanostructured Lipid Carrier Drug Delivery SystemYogeshIJTSRD
Objective Nanostructured lipid carrier NLC based topical gel of Piroxicam PXM was formulated with the aim of controlled release action and to reduce systemic side effect for the treatment of an arthritic condition. Methods NLCs developed using high pressure homogenization method and optimized using a 32 factorial design with response surface methodology using design expert software. NLCs were characterized for particle size, zeta potential analysis, drug entrapment efficiency, and in vitro drug release studies to select the optimized formulation. The NLCs were suitably gelled and evaluated with respect to homogeneity, pH, viscosity, gel strength, spread ability, rheological characteristics, drug content, in vitro diffusion, and stability study. Safety of the NLC based gel was assessed using primary skin irritation studies, and efficacy was confirmed using carrageen an induced rat paw edema model. Results NLCs formulation comprising 2 of lipid 60 40 and surfactant 1.50 was confirmed as an optimized batch having a particle size 138.2±3.60 nm with polydispersibility index value 0.344±0.034. The zeta potential value indicates good physical stability. Based on the results from the in vitro release study it was shown that the formed gels had the ability to extend release of PXM for 24 h and showing percentage drug release of 90.92 ±1.96 at the end of 24 h. Skin irritation studies revealed that the optimized gel formulation shows no erythema, edema, or ulceration. Conclusion The overall results of the present study clearly indicated promising potentials of NLC based gel for delivering PXM topically over the conventional gel. Dr. G. Jagadish | Dr. Rita Mourya | Dr. Amith Nayak "Piroxicam Nanostructured Lipid Carrier Drug Delivery System" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-5 | Issue-3 , April 2021, URL: https://www.ijtsrd.com/papers/ijtsrd39912.pdf Paper URL: https://www.ijtsrd.com/pharmacy/pharmaceutics/39912/piroxicam-nanostructured-lipid-carrier-drug-delivery-system/dr-g-jagadish
POTENTIAL OPTION FOR COMPUTATIONAL FLUID DYNAMIC (CFD) SCHEME IN BIODIESEL ST...IAEME Publication
Biodiesel fuel represents a unique opportunity in the current global energy
scenario owing to its sustainability, renewability and potential to be universally
accessible. Experimental and analytical works have established a mismatch between
fuel chemistry and current diesel engine design. This, to some extent, accounts for
observed challenges in performance and emissions from engines running on biodiesel.
Computational schemes have played an increasingly important role in defining the
scope of these challenges. Computational models’ reliability has improved over time
in predicting engine performance and emissions. Identifying a combustion strategy
that works best for biodiesel is a research imperative. This review presents some of
the strategies that have the potential to enhance biodiesel’s advantages and mitigate
the observed challenges
Presented to: Subgroup of the Kentucky Chemical Demilitarization Citizens’ Advisory Commission and
Chemical Destruction Community Advisory Board
Secondary Waste Working Group
Presented by:
Jeff Brubaker
ACWA Site Manager
Doug Omichinski
Systems Contractor Project Manager
Roger Thompson, CIH, CSP
Systems Contractor Safety & Health Manager
Charlie Satterwhite, CIH
Systems Contractor Senior Industrial Hygienist
Dr. John Barton
Systems Contractor Chief Scientist
Neil Frenzl
Systems Contractor Resident Engineering Manager
Piroxicam Nanostructured Lipid Carrier Drug Delivery SystemYogeshIJTSRD
Objective Nanostructured lipid carrier NLC based topical gel of Piroxicam PXM was formulated with the aim of controlled release action and to reduce systemic side effect for the treatment of an arthritic condition. Methods NLCs developed using high pressure homogenization method and optimized using a 32 factorial design with response surface methodology using design expert software. NLCs were characterized for particle size, zeta potential analysis, drug entrapment efficiency, and in vitro drug release studies to select the optimized formulation. The NLCs were suitably gelled and evaluated with respect to homogeneity, pH, viscosity, gel strength, spread ability, rheological characteristics, drug content, in vitro diffusion, and stability study. Safety of the NLC based gel was assessed using primary skin irritation studies, and efficacy was confirmed using carrageen an induced rat paw edema model. Results NLCs formulation comprising 2 of lipid 60 40 and surfactant 1.50 was confirmed as an optimized batch having a particle size 138.2±3.60 nm with polydispersibility index value 0.344±0.034. The zeta potential value indicates good physical stability. Based on the results from the in vitro release study it was shown that the formed gels had the ability to extend release of PXM for 24 h and showing percentage drug release of 90.92 ±1.96 at the end of 24 h. Skin irritation studies revealed that the optimized gel formulation shows no erythema, edema, or ulceration. Conclusion The overall results of the present study clearly indicated promising potentials of NLC based gel for delivering PXM topically over the conventional gel. Dr. G. Jagadish | Dr. Rita Mourya | Dr. Amith Nayak "Piroxicam Nanostructured Lipid Carrier Drug Delivery System" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-5 | Issue-3 , April 2021, URL: https://www.ijtsrd.com/papers/ijtsrd39912.pdf Paper URL: https://www.ijtsrd.com/pharmacy/pharmaceutics/39912/piroxicam-nanostructured-lipid-carrier-drug-delivery-system/dr-g-jagadish
POTENTIAL OPTION FOR COMPUTATIONAL FLUID DYNAMIC (CFD) SCHEME IN BIODIESEL ST...IAEME Publication
Biodiesel fuel represents a unique opportunity in the current global energy
scenario owing to its sustainability, renewability and potential to be universally
accessible. Experimental and analytical works have established a mismatch between
fuel chemistry and current diesel engine design. This, to some extent, accounts for
observed challenges in performance and emissions from engines running on biodiesel.
Computational schemes have played an increasingly important role in defining the
scope of these challenges. Computational models’ reliability has improved over time
in predicting engine performance and emissions. Identifying a combustion strategy
that works best for biodiesel is a research imperative. This review presents some of
the strategies that have the potential to enhance biodiesel’s advantages and mitigate
the observed challenges
What curiosity in the structure hollow earth in scienceMarcus 2012
http://marcusvannini2012.blogspot.com/
http://www.marcusmoon2022.org/designcontest.htm
Shoot for the moon and if you miss you'll land among the stars...
The ten lost tribes of israel hollow earthMarcus 2012
http://marcusvannini2012.blogspot.com/
http://www.marcusmoon2022.org/designcontest.htm
Shoot for the moon and if you miss you'll land among the stars...
http://marcusvannini2012.blogspot.com/
http://www.marcusmoon2022.org/designcontest.htm
Shoot for the moon and if you miss you'll land among the stars...
Hollow earth & life in universe – a vedic viewMarcus 2012
http://marcusvannini2012.blogspot.com/
http://www.marcusmoon2022.org/designcontest.htm
Shoot for the moon and if you miss you'll land among the stars...
http://marcusvannini2012.blogspot.com/
http://www.marcusmoon2022.org/designcontest.htm
Shoot for the moon and if you miss you'll land among the stars...
Bernard, dr. rw the hollow earth - the greatest geographical discovery in h...Marcus 2012
http://marcusvannini2012.blogspot.com/
http://www.marcusmoon2022.org/designcontest.htm
Shoot for the moon and if you miss you'll land among the stars...
GraphRAG is All You need? LLM & Knowledge GraphGuy Korland
Guy Korland, CEO and Co-founder of FalkorDB, will review two articles on the integration of language models with knowledge graphs.
1. Unifying Large Language Models and Knowledge Graphs: A Roadmap.
https://arxiv.org/abs/2306.08302
2. Microsoft Research's GraphRAG paper and a review paper on various uses of knowledge graphs:
https://www.microsoft.com/en-us/research/blog/graphrag-unlocking-llm-discovery-on-narrative-private-data/
Let's dive deeper into the world of ODC! Ricardo Alves (OutSystems) will join us to tell all about the new Data Fabric. After that, Sezen de Bruijn (OutSystems) will get into the details on how to best design a sturdy architecture within ODC.
Essentials of Automations: Optimizing FME Workflows with ParametersSafe Software
Are you looking to streamline your workflows and boost your projects’ efficiency? Do you find yourself searching for ways to add flexibility and control over your FME workflows? If so, you’re in the right place.
Join us for an insightful dive into the world of FME parameters, a critical element in optimizing workflow efficiency. This webinar marks the beginning of our three-part “Essentials of Automation” series. This first webinar is designed to equip you with the knowledge and skills to utilize parameters effectively: enhancing the flexibility, maintainability, and user control of your FME projects.
Here’s what you’ll gain:
- Essentials of FME Parameters: Understand the pivotal role of parameters, including Reader/Writer, Transformer, User, and FME Flow categories. Discover how they are the key to unlocking automation and optimization within your workflows.
- Practical Applications in FME Form: Delve into key user parameter types including choice, connections, and file URLs. Allow users to control how a workflow runs, making your workflows more reusable. Learn to import values and deliver the best user experience for your workflows while enhancing accuracy.
- Optimization Strategies in FME Flow: Explore the creation and strategic deployment of parameters in FME Flow, including the use of deployment and geometry parameters, to maximize workflow efficiency.
- Pro Tips for Success: Gain insights on parameterizing connections and leveraging new features like Conditional Visibility for clarity and simplicity.
We’ll wrap up with a glimpse into future webinars, followed by a Q&A session to address your specific questions surrounding this topic.
Don’t miss this opportunity to elevate your FME expertise and drive your projects to new heights of efficiency.
The Art of the Pitch: WordPress Relationships and SalesLaura Byrne
Clients don’t know what they don’t know. What web solutions are right for them? How does WordPress come into the picture? How do you make sure you understand scope and timeline? What do you do if sometime changes?
All these questions and more will be explored as we talk about matching clients’ needs with what your agency offers without pulling teeth or pulling your hair out. Practical tips, and strategies for successful relationship building that leads to closing the deal.
PHP Frameworks: I want to break free (IPC Berlin 2024)Ralf Eggert
In this presentation, we examine the challenges and limitations of relying too heavily on PHP frameworks in web development. We discuss the history of PHP and its frameworks to understand how this dependence has evolved. The focus will be on providing concrete tips and strategies to reduce reliance on these frameworks, based on real-world examples and practical considerations. The goal is to equip developers with the skills and knowledge to create more flexible and future-proof web applications. We'll explore the importance of maintaining autonomy in a rapidly changing tech landscape and how to make informed decisions in PHP development.
This talk is aimed at encouraging a more independent approach to using PHP frameworks, moving towards a more flexible and future-proof approach to PHP development.
Smart TV Buyer Insights Survey 2024 by 91mobiles.pdf91mobiles
91mobiles recently conducted a Smart TV Buyer Insights Survey in which we asked over 3,000 respondents about the TV they own, aspects they look at on a new TV, and their TV buying preferences.
"Impact of front-end architecture on development cost", Viktor TurskyiFwdays
I have heard many times that architecture is not important for the front-end. Also, many times I have seen how developers implement features on the front-end just following the standard rules for a framework and think that this is enough to successfully launch the project, and then the project fails. How to prevent this and what approach to choose? I have launched dozens of complex projects and during the talk we will analyze which approaches have worked for me and which have not.
UiPath Test Automation using UiPath Test Suite series, part 4DianaGray10
Welcome to UiPath Test Automation using UiPath Test Suite series part 4. In this session, we will cover Test Manager overview along with SAP heatmap.
The UiPath Test Manager overview with SAP heatmap webinar offers a concise yet comprehensive exploration of the role of a Test Manager within SAP environments, coupled with the utilization of heatmaps for effective testing strategies.
Participants will gain insights into the responsibilities, challenges, and best practices associated with test management in SAP projects. Additionally, the webinar delves into the significance of heatmaps as a visual aid for identifying testing priorities, areas of risk, and resource allocation within SAP landscapes. Through this session, attendees can expect to enhance their understanding of test management principles while learning practical approaches to optimize testing processes in SAP environments using heatmap visualization techniques
What will you get from this session?
1. Insights into SAP testing best practices
2. Heatmap utilization for testing
3. Optimization of testing processes
4. Demo
Topics covered:
Execution from the test manager
Orchestrator execution result
Defect reporting
SAP heatmap example with demo
Speaker:
Deepak Rai, Automation Practice Lead, Boundaryless Group and UiPath MVP
Neuro-symbolic is not enough, we need neuro-*semantic*Frank van Harmelen
Neuro-symbolic (NeSy) AI is on the rise. However, simply machine learning on just any symbolic structure is not sufficient to really harvest the gains of NeSy. These will only be gained when the symbolic structures have an actual semantics. I give an operational definition of semantics as “predictable inference”.
All of this illustrated with link prediction over knowledge graphs, but the argument is general.
Transcript: Selling digital books in 2024: Insights from industry leaders - T...BookNet Canada
The publishing industry has been selling digital audiobooks and ebooks for over a decade and has found its groove. What’s changed? What has stayed the same? Where do we go from here? Join a group of leading sales peers from across the industry for a conversation about the lessons learned since the popularization of digital books, best practices, digital book supply chain management, and more.
Link to video recording: https://bnctechforum.ca/sessions/selling-digital-books-in-2024-insights-from-industry-leaders/
Presented by BookNet Canada on May 28, 2024, with support from the Department of Canadian Heritage.
Search and Society: Reimagining Information Access for Radical FuturesBhaskar Mitra
The field of Information retrieval (IR) is currently undergoing a transformative shift, at least partly due to the emerging applications of generative AI to information access. In this talk, we will deliberate on the sociotechnical implications of generative AI for information access. We will argue that there is both a critical necessity and an exciting opportunity for the IR community to re-center our research agendas on societal needs while dismantling the artificial separation between the work on fairness, accountability, transparency, and ethics in IR and the rest of IR research. Instead of adopting a reactionary strategy of trying to mitigate potential social harms from emerging technologies, the community should aim to proactively set the research agenda for the kinds of systems we should build inspired by diverse explicitly stated sociotechnical imaginaries. The sociotechnical imaginaries that underpin the design and development of information access technologies needs to be explicitly articulated, and we need to develop theories of change in context of these diverse perspectives. Our guiding future imaginaries must be informed by other academic fields, such as democratic theory and critical theory, and should be co-developed with social science scholars, legal scholars, civil rights and social justice activists, and artists, among others.
Dev Dives: Train smarter, not harder – active learning and UiPath LLMs for do...UiPathCommunity
💥 Speed, accuracy, and scaling – discover the superpowers of GenAI in action with UiPath Document Understanding and Communications Mining™:
See how to accelerate model training and optimize model performance with active learning
Learn about the latest enhancements to out-of-the-box document processing – with little to no training required
Get an exclusive demo of the new family of UiPath LLMs – GenAI models specialized for processing different types of documents and messages
This is a hands-on session specifically designed for automation developers and AI enthusiasts seeking to enhance their knowledge in leveraging the latest intelligent document processing capabilities offered by UiPath.
Speakers:
👨🏫 Andras Palfi, Senior Product Manager, UiPath
👩🏫 Lenka Dulovicova, Product Program Manager, UiPath
2. UNCLASSIFIED
research4. These, in addition to inherently less as the rapid restart capabilities required for the precise
dangerous solid, hybrid, and gel formulations, are often positioning of multiple reentry vehicles. For the
classified as “green” propellants because of the lower purposes of this study, the MM III PSRE has been
environmental and personnel dangers that they pose taken as the archetype for the mission definition and
compared to other high-performance propellants. physical dimensions of the candidate concepts.
Although less toxic, these propellants do not have a Largest
Overall OEC Value
proven record for ICBM application. Research and Propellant Candidate Green
Evaluation
testing must prove them to be capable of hypergolic or Combinations Propellants
Criterion
near instantaneous ignition, to provide high levels of
Lowest
specific impulse, and to be storable without significant System
degradation for a service life of as much as 30 years. Most Plausible Weight, Sized Concept
Hypergolicity is a challenge because many of the Green Propellants Cost, Concepts Definitions
proposed formulations require soluble catalysts to and Risk
provide the capability. Storage life is a concern for
HTP because it degrades significantly over time at Figure 1: Overview of Propellant Evaluation Method
normal storage temperatures.
PROPELLANT IDENTIFICATION
This study evaluates the potential of the various green As a first step in identifying candidate green
propellants for use in a notional next-generation Post- propellants, extensive data available in the literature
Boost Propulsion System (PBPS). The authors assert were collected for a wide variety of propellant
that the most effective method of implementing this formulations. The data consisted of metrics that are
evaluation is through discerning the system level effects valuable for evaluating propellant applicability in the
of the propellant selection. This evaluation is areas of environmental and/or personnel hazard (i.e.
accomplished by the following process: “greenness”), performance, and PBPS design
integration. The following quantitative metrics were
• Identify propellant formulations that have the most compiled for each propellant formulation:
potential for the application
• Formulate and size a PBPS concept for each • Mixture ratio
propellant, incorporating proposed propulsion • Densities of oxidizer and fuel
technologies that may be required to realize system • Viscosities of oxidizer and fuel
performance • Vapor pressures of oxidizer and fuel
• Evaluate the concepts in terms of key metrics such • Frozen equilibrium specific impulse for an
as weight, cost, and technical risk expansion from 300 psia to 14.7 psia
• National Institute for Occupational Safety and
To identify green propellants with the most potential for Health (NIOSH) recommended exposure limits
the application, an Overall Evaluation Criterion (OEC) (REL) for oxidizer and fuel
method was used. This method allowed the ranking of
propellant candidates based on qualitative and The NIOSH recommended exposure limits were used to
quantitative attributes such as performance, system quantify propellant toxicity because these are the most
complexity, and toxicity. After comparing propellant stringent government guidelines5.
combinations through the OEC method, the most
plausible candidates from each propellant “family” (e.g. In addition to these quantitative metrics, qualitative
liquid, solid, etc.) were selected for further analysis. A rankings were established for certain characteristics that
PBPS concept was sized for each candidate propellant are either not easily represented as continuous numeric
based on extrapolations from current systems. These values or not widely available other than as
concepts were then compared based on considerations generalizations. These rankings were specified as
such as their total weight, cost, and possible technology integers ranging from one to five with three
development issues. These results were used to draw corresponding to the metric ranking of the current MM
conclusions on the applicability of the various green III PSRE, one corresponding to significantly worse than
propellants for a future PBPS system. This process is the existing system, and five indicating significantly
summarized in Figure 1. better than the baseline. These metrics include the
following:
The current Minuteman III Propulsion System Rocket
Engine (PSRE) uses monomethyl-hydrazine and • Storability of oxidizer and fuel
nitrogen tetroxide, two highly toxic hypergolic
• Ease of inerting oxidizer and fuel
propellants that provide good specific impulse as well
UNCLASSIFIED 2
3. UNCLASSIFIED
• Ignition delay Weights indicate importance of metric in decision
• Complexity of implementing the propellant in a
propulsion system
OEC = α + β Baseline Metric + γ
Metric Metric
Baseline Metric Metric Baseline Metric
Data was obtained for 68 distinct propellant
formulations (i.e. combinations of oxidizer and fuel at a
certain mixture ratio) that have been used in production
rocket engines or have been studied extensively in Maximize Metric Minimize Metric Maximize Metric
laboratory experiments. These formulations include
liquid (including mono- and bi-propellants), solid, Figure 2: General Form of the OEC Equation
hybrid, and gel propellants. In addition to green
propellants, traditional propellant formulations were As shown in the figure, the terms of the OEC equation
included for comparative purposes. Cryogenic are preceded by scaling factors. These factors are used
propellants were eliminated from consideration because to weight the importance of each term relative to the
of their incompatibility with the Minuteman OEC metric. The weights are chosen as fractions
infrastructure and their very low storage lives, and whose sum is 1.0. By choosing such a format, the value
gaseous propellants were omitted because their very of the OEC for the baseline alternative is 1.0.
low density make packaging impractical. The Alternatives with an OEC value greater than that of the
propellant data was culled from several sources baseline are more desirable, while alternatives with
including technical reports and papers, the proceedings values less than the baseline are less favorable.
of the Second International Hydrogen Peroxide
Propulsion Conference, the NIOSH internet web site, For the purposes of propellant selection, an OEC
and the Weight Engineers Handbook. These sources equation was developed that is a function of the
are listed as references 6-13.6,7,8,9,10,11,12,13 previously identified propellant metrics. The OEC is
shown in Equation 1 below.
In order to identify the propellants that represent the
most suitable blend of performance and “greenness”, an Equation 1: Propellant Selection OEC
overall evaluation criterion method was used. The
OEC is a single numerical metric that can be used to OEC = α Specific Weight + β Isp + γ Greenness +
Specific Weight Isp
Greenness
compare alternatives. The OEC is formulated such that BL BL BL
higher values represent more highly preferred solutions. Sys. Complexity Ignition DelayBL
The core of the OEC method is its defining equation. δ + ε
Sys. ComplexityBL Ignition Delay
The equation consists of a sum of several terms, each of
which represents a particular characteristic upon which
The specific weight and greenness terms shown in the
the alternative is evaluated14. Each term is formed as a
equation are defined as functions of multiple metrics.
quotient comprised of the value of the respective
The specific weight is the inverse of the weighted
characteristic for a particular alternative and the value
average of the oxidizer and fuel densities. As such, it is
for a chosen baseline alternative. Because higher
a function of mixture ratio that indicates the volumetric
values of the OEC are intended to represent more
efficiency of the propellant combination. Equation 2
favorable options, the numerator and denominator of
shows the expression for the greenness metric.
this quotient are interchanged as necessary to obtain the
Formulated as a general indicator of the propellant
desired direction of optimality. For instance, if
environmental and personnel hazard, it is intended to
increasing a certain metric is desirable, the value for the
capture not only the direct toxicity of the propellant but
alternative is placed in the numerator with the baseline
also the ease of containing and inerting any propellant
value in the denominator. This formulation will yield a
spills. For this reason, it was specified as a function of
value of the quotient greater than 1.0 for an alternative
the REL to indicate toxicity directly and metrics such as
with a higher value of the metric than the baseline. The
vapor pressure (VP) and ease of inerting to indicate the
ratio is inverted for metrics that are more desirable
hazard associated with a propellant leak. The
when minimized. The general form of the OEC
logarithms of the REL and vapor pressure metrics that
equation is shown in Figure 2.
appear within the equation are used to compress the
orders of magnitude variations that can occur in the
parameters for different propellants into a linear form
suitable for application in an OEC.
UNCLASSIFIED 3
4. UNCLASSIFIED
Equation 2: Toxicity OEC Term scenarios considered. The HTP/CINCH formulation
Greenness γ log(100 * Ox. REL) log(100 * Fuel REL)
closely follows. It is interesting to note that the
γ
Greenness = + +
BL 6 log(100 * Ox. RELBL ) log(100 * Fuel RELBL )
HTP/NHMF is superior to the NTO/MMH that is used
log(Ox. VPBL ) log (Fuel VPBL ) Inert Ox. Inert Fuel in the current PSRE in every case except for the purely
log( Ox. VP ) + log( Fuel VP ) + Inert Ox.
+
Inert Fuel
BL BL
performance weighted scenario in which it trails only
slightly. The CINCH formulation outperforms the
This OEC method for propellant selection is not unique NTO/MMH even for the performance scenario.
3
and does not necessarily assure the best selection. It is
Performance Scenario
only one of several decision methods for ranking Scenario 2
alternatives based on subjective and objective data. It 2.5 Scenario 3
also suffers from some shortcomings including the Scenario 4
Scenario 5
presumption that all attributes are independent. The 2 Toxicity Scenario
OEC method was chosen, however, because it was
tractable and provided good visibility and traceablity
OEC
1.5
for the propellant pre-screening process.
1
After developing the propellant evaluation OEC
equation, a series of weighting scenarios was developed
against which the propellants should be judged. Each 0.5
scenario is comprised of a set of weighting scalars,
whose sum is 1.0, that indicate the relative importance 0
Nitrogen 98%HTP/ 90% HTP/ Whole Fuming HTP/CINCH
of each metric to the OEC. Multiple scenarios were Tetroxide/MMH Ethanol Hydrazine Nitric Acid/JP-4
used to prevent a biasing of the results caused by a
single particular choice of weightings. This method Figure 3: Example of Average OEC Across the Spectrum
ensures that no propellants are eliminated from of Scenarios
consideration because of poor performance on only one The propellants within each family of similar concepts
scenario. Propellants were judged on their suitability (e.g., liquid, solid, etc.) with the highest average OEC
across the entire spectrum of scenarios studied. Table I performance were selected as candidates for which a
shows the scenarios developed for propellant screening. sized PBPS concept would be developed. These
As shown in the table, the six scenarios range propellants are the following:
successively in emphasis from performance to toxicity.
• Ethanol Nontoxic Hypergolic Miscible Fuel
Table I: Propellant Evaluation Scenarios (NHMF) / High Test Peroxide (HTP) liquid
Performance Toxicity
• Competitive Impulse Non-Carcinogenic Hypergol
Scenario
Scenario 1 Scenario 2 Scenario 3 Scenario 4 Scenario 5 Scenario 6
Scenario (CINCH) / HTP liquid
Specific System Ignition • Monomethyl hydrazine (MMH) / nitrogen tetroxide
Weight,
α
Isp,
β
Toxicity, Complexity, Delay,
γ δ ε
(NTO) loaded gel
Scenario
Performance (1) 0.3 0.5 0 0.1 0.1 • Polyethylene (PE) / HTP hybrid
2
3
0.3
0.3
0.4
0.3
0.1
0.2
0.1
0.1
0.1
0.1
• Aluminum / hydroxy-terminated polybutadiene
4 0.25 0.25 0.3 0.1 0.1 (HTPB) / ammonium perchlorate solid
5 0.25 0.25 0.4 0.1 0
Toxicity (6) 0.2 0.2 0.5 0.1 0
Figure 4 shows the weighted values of each OEC term
for the selected liquid, hybrid, and gel propellants
Using the weightings within each scenario, the OEC
evaluated for the performance and toxicity scenarios.
was calculated for each propellant within the database
Because desirability relative to the baseline is
using the current MM III PSRE propellants, NTO and
comprised of OEC values greater than 1.0, it is clear
MMH, as the baseline. From the results, the propellant
that all of the selected propellants exhibit significantly
within each family with the highest average OEC value
lower toxicity and, at worst, only marginally decreased
across the scenarios was noted. An example of this
performance relative to the MMH/NTO liquid used in
“average” OEC performance for some of the
the existing MM III PSRE. These results indicate that
propellants examined is shown in Figure 3. In this
the selected green propellants should prove good
excerpt from the OEC results, it is clear the
candidates for the PBPS application.
HTP/ethanol NHMF is, on average, superior to the
other propellants listed for the spectrum of weighting
UNCLASSIFIED 4
5. UNCLASSIFIED
2.5
Ignition Delay
Toxicity Scenario
System Complexity
2
Performance Scenario
Performance Scenario
Toxicity Scenario
Performance Scenario
Performance Scenario
Toxicity Scenario
Greenness
Toxicity Scenario
1.5 Specific Impulse
OEC
Specific Weight
1
0.5
0
98% HTP / Ethanol NHMF 98% HTP / Polyethylene
Gelled NTO/MMH 98% HTP / CINCH
Liquid Hybrid
Figure 4: OEC Component Breakdown for Selected Propellants
Post Boost Propulsion System Concepts
Current PSRE 1 2 3 4 5
MMH / NTO HTP / alcohol HTP / CINCH HTP / NTO / MMH HTPB / ammonium
Propellant
liquid liquid liquid polyethylene gel perchlorate solid
Primary
Propulsion Thrust metering pintle/hot gas bypass
valving valving valving valving valving
System system system
Thrust gimballed gimballed gimballed gimballed gimballed
gimballed engine
vectoring engine engine engine engine engine
ducted primary ducted primary ducted primary ducted primary ducted primary
ducted hot gas
System type propellant propellant propellant propellant propellant
Attitude thrusters/DACS
thrusters thrusters thrusters thrusters thrusters
Control
System
Thrust metering hot gas bypass
valving valving valving valving valving
system system
Propellant pressurized pressurized pressurized pressurized pressurized
Feed system no feed system
Expulsion and cold gas cold gas cold gas cold gas cold gas
Distribution Pressure tank
cylindrical spherical spherical spherical spherical no tank
Systems shape
cylindrical thrust
Propellant Fuel tank shape cylindrical spherical spherical cylindrical spherical
chamber
Storage
Oxidizer tank integral to fuel
Assemblies cylindrical spherical spherical spherical spherical
shape tank/thrust chamber
Figure 5: Matrix of Candidate PBPS Concepts
CANDIDATE CONCEPT DEFINITION For the purposes of developing conceptual
In order to develop a PBPS concept for each propellant, configurations, modified versions of the
several alternative subsystem design and technology aluminum/magnesium monocoque structure from the
concepts were explored. The subsystem categories existing MM III PSRE were assumed.
include the primary propulsion system, the attitude
control system, the propellant expulsion and The principal design decisions in the development of a
distribution systems, and the propellant storage PBPS configuration are those defining the primary
assemblies. Structural support alternatives were not propulsion system. The primary propulsion system
initially explored during the development of PBPS design decisions were classified as selection of the
concepts. This decision to isolate structural propellant formulation, the impulse cycling method,
technologies was made in order to allow comparison of and the thrust vectoring technique. Because concepts
the concepts only through the implications of the were developed for each propellant formulation, the
propellant selection on the subsystem and components.
UNCLASSIFIED 5
6. UNCLASSIFIED
decisions on impulse cycling and vectoring must and 2% per year15. With a 1%/year rate, HTP at an
correspond to the particular propellant. initial concentration of 98% degrades to 72.5%
concentration within the 30 year storage life expected
Based on these subsystem alternatives, a notional PBPS for the next generation PBPS. If it is maintained at a
subsystem configuration was developed for each of the temperature near 25°F, however, the yearly
five selected propellants. The five configurations are decomposition rate is reduced to approximately 0.01%.
outlined in Figure 5. These configurations were formed This rate of decomposition means that an initial
by considering the subsystem options that were concentration of 98% HTP would decompose to 94.5%
expected to yield the minimum weight and minimum during the 30 year storage life. This level of
technological risk solutions. For instance, all of the degradation is manageable from a propellant sizing
configurations employing liquid propellants contain standpoint.
spherical propellant storage tanks. Trade studies
indicated that these tanks provided the minimum weight One possible solution to hold the hydrogen peroxide
solutions and could be packaged within the dimensional temperature near 25°F during nominal silo storage is to
envelope of the current MM III PSRE. Also, the liquid attach solid-state cooling devices, called thermo-electric
systems were all designed with cold gas expulsion coolers (TECs) to the oxidizer tanks. These devices are
systems. Cold gas systems were believed to provide commercially available, inexpensive, lightweight, and
lower weight (relative to a pump) and more accurate have demonstrated 30 years of continuous operation in
expulsion control (relative to a hot gas system). For space-based applications15. Due to their low weight
thrust vectoring, all designs incorporate mechanically and cost, the TECs could be made multiply redundant.
gimbaled engines. These systems were viewed to be
potentially lighter and lower risk than fluidic control, Vent valve
(1 of 2) Oxidizer
jet tabs, or jet vanes. Thermoelectric
devices and Manifold Fuel Manifold
heat sinks
ACS engines
The systems incorporating solid propellant components
have some significant differences from the liquid
propellant concepts. For instance, both the hybrid Insulated
H2O2
HTP/PE and the solid ammonium perchlorate/HTPB Tanks
system use cylindrical fuel storage assemblies that
Gas
serve as the combustion chambers. The cylindrical Storage
Assembly Mechanically gimballed
design allows for integration of a solid grain conducive axial nozzle
for even burning. In the pure solid system, the oxidizer
consists of grains commingled with the fuel, while in
the hybrid system, the oxidizer is stored as a liquid in
separate spherical tanks. These concepts also have NHMF
(Ethanol) Tank
significantly different attitude control systems (ACS)
configurations than their liquid counterparts. The Figure 6: HTP/NHMF Candidate Schematic
hybrid system uses the oxidizer as a monopropellant for
the attitude control engines. The pure solid system
employs ducted hot gas from the solid propellant gas NTO/MMH LOADED GEL CONCEPT
generators and a divert attitude control system (DACS) The NTO/MMH gelled propellant concept consists of a
to provide a multi-tiered approach to attain precise single spherical oxidizer storage assembly, a spherical
vernier positioning. fuel storage assembly, and a spherical gas storage
assembly in addition to the axial and attitude engines.
HTP/NHMF, HTP/CINCH LIQUID CONCEPTS
The schematic for the HTP/NHMF concept is shown in One of the key drivers of the gelled propellant design is
Figure 6. The HTP/CINCH concept is identical except the high system pressure that is required. Because the
for the change in fuel (and the corresponding tank gels are thixotropic (they become liquid under
sizing). One of the major design challenges that must pressure), high pressures are needed before the gels will
be overcome in developing a feasible HTP system is the flow through the propellant ducting. In order to handle
mitigation of the oxidizer’s tendency to degrade. High the system pressures, both the gas and propellant
purity HTP is required to maintain acceptable levels of storage assemblies and the propellant distribution
performance; however, HTP slowly decomposes to system must be strengthened, adding significant weight
water and oxygen. This decomposition is a strong to the structure.
function of temperature. At a typical silo temperature
of 70°F, the HTP decomposition rate is between 1%
UNCLASSIFIED 6
7. UNCLASSIFIED
Another unique challenge of the gelled propellant from a sink. As combustion occurs, the hot gas is
concept is design of the engine propellant valves. expelled through the centrally located nozzle throat.
Although loading the gelled fuel with aluminum The general configuration of this concept is shown in
particulates increases the propellant performance, the Figure 7.
particulates have a tendency to clog valves and
injection orifices. Because of the technological risk Injection Velocity
associated with a large loading fraction, the concept for Vectors
this study employs only the minimal loading level
required to negate the performance degradation due to
the presence of the gellant material. This low level of
loading should preclude the need for complex valve
assemblies, but some changes over a liquid system may
prove necessary. If future studies indicate that valve Oxidizer
clogging will be an issue, a valve design employing a Injectors
translating centerbody with a wiping capability could
be incorporated.
Fuel
HTP/POLYETHYLENE HYBRID Grain
The primary assemblies comprising the configuration of
Chamber
the HTP/polyethylene hybrid concept are three HTP
Nozzle
oxidizer storage assemblies, a gas storage assembly,
and a fuel storage/combustion chamber. The necessity Figure 7: Circumferential Swirl Injection Thrust
for three oxidizer storage assemblies is driven by the Chamber
high value of the optimum mixture ratio.
Correspondingly, the fuel storage/combustion chamber
is comparatively small. This “swirl” effect has additional advantages. The
circumferential component of the oxidizer injection
The primary advantage of a hybrid propulsion concept velocity serves to improve propellant mixing and to
is that it incorporates many of the favorable reduce the chamber size necessary to achieve a
characteristics of both liquid and solid propellant residence time greater than the ignition delay. The
systems. As with liquid systems, hybrid engines allow swirling also results in a layer of cool oxidizer on the
impulse cycling. This cycling is achieved by periphery of the combustion chamber. This layer
incorporating a throttleable valve that controls the shields the chamber walls from high heat loads.
oxidizer injection into the combustion chamber. The
hybrid system gains two critical advantages over liquid Another unique feature of the HTP/PE concept is the
rocket systems. These are the increased density and design of the attitude control engines. Hybrid systems
decreased environmental hazard of the fuel. Because of are often characterized by poor ignition delay times, so
the increased density, more fuel mass can be packaged the development of an effective ACS engine may
in a smaller volume. This characteristic is especially involve significant technical risk. An ACS thruster
advantageous for a volume-constrained upper stage concept that uses HTP as a monopropellant may prove
application such as a PBPS. The solid fuel has a very more risk averse. The hydrogen peroxide fuel can be
low environmental and personnel hazard both because used as a monopropellant by catalyzing the HTP such
it cannot leak and flow and because it has negligible that it exothermically decomposes into water vapor and
toxicity. oxygen gas17. The resulting hot gaseous products can
be expelled through a nozzle to produce the required
In order to facilitate thrust chamber packaging, a thrust. Though the reaction time of this catalytic HTP
circumferential swirl injection combustion chamber decomposition would not be low enough to ensure an
design was adopted. This design concept, similar to the adequate ignition delay and minimum impulse for the
Surrey Vortex Flow “Pancake” Engine16, allows a low ACS engines, an integral accumulator reservoir within
aspect ratio construction because oxidizer is injected at the ACS engine has been incorporated for storing
ports located around the circumference of the catalyzed decomposition products. The presence of this
combustion chamber rather than in one. The injectors tank within the thrusters allows the HTP to be catalyzed
are oriented such that the liquid stream has a significant in a quasi-steady manner such that hot gas is always
circumferential component. This orientation causes the available for rapid engine firings. This thruster
oxidizer to “swirl” around the combustion chamber configuration is depicted in Figure 8.
toward the center in a similar fashion as water drains
UNCLASSIFIED 7
8. UNCLASSIFIED
Accumulator Reservoir To attain acceptable levels of pointing accuracy and
Catalyst Bed precise downrange and crossrange velocity increments,
a PBPS design must allow high fidelity thrust control
for both the axial and the attitude control engines. This
thrust control is characterized by a small minimum
impulse capability, low ignition delay, and impulse
cycling capability. A high level of thrust control is
Propellant Valve
difficult to achieve in solid propellant systems because
Nozzle the engines fire at a designed burn rate until all of the
Hot Gas Valve
propellant is expended. Although some control may be
Figure 8: HTP Monopropellant ACS Engine afforded by designing the propellant grain structure to
vary thrust over a certain profile during the burn, the
Although the HTP monopropellant thruster concept exact burn profile requirement for a given PBPS
should overcome the issue of ignition delay for the mission cannot be known a priori and certainly cannot
ACS engines, ignition delay could remain a problem for be generalized to a single grain design. This difficulty
the axial engine. Many current hybrid rocket engines arises from the flexibility that the PBPS must afford: it
have ignition delays of several seconds. Such delays must be capable of correcting any positioning errors
are unacceptable for the PBPS application. This resulting from the boost phase of the mission, and it
concern is amplified by the fact that hybrid motors have must allow independent targeting of three RVs over a
not been demonstrated for upper stage application. An wide range of flight paths. To allow this flexibility
additional concern for the hybrid concept is in within a solid propellant system, a multi-tiered
packaging the combustion chamber. The low aspect “tunneling” approach was devised to attain accurate
ratio of the chamber allows it to fit within the outer positioning. The system envisioned for this study
PBPS geometric envelope, but sizing studies have consists of three discrete levels of propulsive capability
indicated that a purely cylindrical chamber may intrude in which each subsequent tier provides more precise
into the volume occupied by the guidance set gyro thrust control that can correct for the positioning errors
platform of the current MM III. This intrusion would imposed by the previous propulsive level.
necessitate a more complicated combustion chamber
geometry. All of these concerns indicate that a hybrid The first propulsive tier is provided by three primary
concept would entail significant developmental risk. gas generators. These solid propellant thrust chambers
are fired to produce major velocity increments for bulk
SOLID PROPELLANT CONCEPT downrange and crossrange maneuvering. One primary
Figure 9 depicts a schematic of the aluminum/ chamber is provided for each RV. The chambers are
HTPB/ammonium perchlorate solid propellant concept. connected to the attitude control and axial nozzles via
The concept consists of three primary solid propellant high-temperature hot gas ducting. During a burn, the
gas generators, three vernier positioning gas generators, effluent products from the chamber provide both axial
and a final positioning divert attitude control system. and attitude control thrust. Should the thrust
This 3-tiered propulsion scheme is the key attribute of requirements at a given point during the burn be less
the solid propellant concept. than the capability of the chamber, the excess hot gas is
expelled through a series of radially-oriented vent
Primary Propulsion / ACS Valves ACS Engine nozzles. These nozzles are placed symmetrically
around the PBPS circumference and opened in unison
Radial Vent Nozzles
such that the net radial thrust is negligible.
Primary Gas Generators
(with thrust termination Three vernier positioning gas generators comprise the
capability)
second tier of the propulsion system. These chambers,
Vernier Positioning Gas
Generators
similar to those employed by the Trident SLBM18, are
(with thrust termination
Valve
fired to allow positioning during “coast” phases
capability)
Hot Gas Manifold Mechanically Gimballed between major downrange or crossrange maneuvers.
Axial Nozzle Although connected to the same hot gas manifold as the
primary gas generators so that both axial and ACS
DACS impulse can be provided, the vernier positioning
chambers are sized primarily for the ACS duty cycle.
Figure 9: Solid Propellant PBPS Concept The final level of propulsive control is afforded by the
divert attitude control system. This system consists of
UNCLASSIFIED 8
9. UNCLASSIFIED
multiple banks of small solid propellant impulse Assumptions for the concept sizing are listed in Table
charges that are oriented in a pattern similar to that of II. Additional details on the sizing process are
the 10-engine primary ACS of the current MM PSRE. presented in reference 15.
These charges are used to provide precise positioning of
the post-boost vehicle (PBV) immediately prior to RV Select a propellant for the
concept
release. Because the impulse of these charges is small
and can be accurately predicted, multiple charges can Determine the theoretical
be fired immediately before each release to damp out Isp
angular positioning errors and to allow PBV back-away Calculate the required Converged Design
from the RV without applying any significant jolt to the propellant mass from the Rocket
Equation
RV being released. Determine the required Yes
components and draw
a schematic Can the system
Although this solid propellant concept offers significant No
be packaged into the
advantages in propellant “greenness”, it has several Develop a packaging
concept
required volume?
Yes
disadvantages. One issue is weight. The hot gas
No
ducting and valves needed for this concept must be Estimate the component and Has the structural mass Draw an accurate
total system masses estimate changed? concept layout
fabricated from materials capable of withstanding high
temperatures and pressures. For this reason, the hot gas
Figure 10: Concept Development Process Flowchart
distribution system will be heavy. The use of multiple
combustion chambers also amplifies structural weight
significantly. In addition to high weight, the concept is Table II: Table of Sizing Assumptions and Characteristics
also very aggressive from a technology standpoint. Sizing Characteristic Sizing Assumptions
Although some elements of the concept have been Chamber pressure for liquid Fixed for all concepts at 125 psia
demonstrated in the Trident SLBM system, the concepts
technological risk associated with the hot gas Chamber pressure for solid, Fixed for all concepts at 600 psia
distribution system and the DACS is significant. Also, hybrid, and gelled concepts
Expansion ratio/exit pressure Fixed to estimated baseline expansion
a solid propellant system has not been demonstrated for ratio of 26 for all except hybrid, which
the stringent land-based ICBM accuracy requirements. was sized for fixed length nozzle with
Another disadvantage of the solid propellant system is correspondingly higher expansion ratio
that the propellant is a dangerous ordnance item. Structural weight Fixed for all concepts
Propellant storage assemblies Scaled according to required chamber
pressures, fuel volumes, mixture ratios
CANDIDATE CONCEPT SIZING and densities
Candidate concepts were sized by using a rocket Gas storage assemblies Scaled according to required chamber
equation approach. Each sized candidate concept was pressure
provided with enough propellant mass to maintain the Fittings (pressure transducers, Weight fixed, but quantity adjusted
filters, squibs, etc.) according to concept
same velocity budget as the current Minuteman III
system (including boost stages and the PSRE). PBPS
Examples of concept layouts are given in Figure 11.
empty weight was estimated by scaling the current
Converged weight breakdowns for the systems are
PSRE sub-system weights based on propellant mass
given in Table III.
and pressure. Figure 10 presents the methodology
formulated used for sizing the candidate concepts.
Main Engine Nozzle Primary Gas Generator Main Engine Nozzle
(1 of 3)
Fuel Tank
Oxidizer Tank
GSA Tank
Vernier Gas Generator
(1 of 3)
Guidance Intrusion
Oxidizer Tank
Guidance Intrusion
Figure 11: Layout of HTP/NHMF Concept (left) and Solid Propellant Concept (right)
UNCLASSIFIED 9
10. UNCLASSIFIED
Table III: Converged Mass Breakdowns for the Candidate Systems
Current HTP/ HTP/ HTP/PE NTO/MMH Solid
MMIII PSRE NHMF CINCH Gel
(Estimated) ‡
System Average Isp (sec) 280.2 269.8 273.9 274.1 284.7 264.7
Subsystem Mass Mass Mass Mass Mass Mass
(lbm) (lbm) (lbm) (lbm) (lbm) (lbm)
Gas Storage Assembly 55.0 55.0 55.0 26.0 60.0 --
Internal Structure 27.0 27.0 27.0 27.0 27.0 27.0
Rocket Engine Assemblies / Thrust Chamber Assemblies 69.0 69.0 69.0 82.0 69.0 72.0
Pyrotechnic Command Cable 7.0 7.0 7.0 7.0 7.0 7.0
Thruster Actuation and Gimble Command Cable 14.0 14.0 14.0 14.0 14.0 14.0
Thermal Insulation Blanket Assembly 15.0 15.0 15.0 15.0 15.0 15.0
External Shell/Interstage Assembly 73.0 73.0 73.0 73.0 73.0 73.0
Propellant Distribution System 19.5 19.5 19.5 10.8 19.5 --
(Propellant Gas Combustion and Distribution System) --- -- -- -- -- 216.6
Oxidizer Propellant Storage Assembly 26.6 13.2 13.2 19.1 19.8 --
Fuel Propellant Storage Assembly / Solid Fuel Grain Casing 26.6 6.9 6.9 26.0 19.8 --
Fasteners / Miscellaneous 9.0 9.0 9.0 9.0 9.0 9.0
Oxidizer Coolant System --- 10 10 -- -- --
Total Structural Mass 341.7 318.6 318.6 295.9 333.1 433.6
Oxidizer Mass (Primary Gas Generator Propellant) 160.0 171.4 151.2 269.8 147.7 400.0
Fuel Mass (Secondary Gas Generator Propellant) 100.0 45.2 58.2 22.3 92.3 115.0
(DACS Propellant) --- -- -- -- -- 40.0
Total Propellant Mass 260.0 216.6 209.4 292.1 240.0 555.0
Total Mass 601.7 535.2 528.0 588.0 573.0 988.6
‡
( ) indicates a subsystem that is only present in the solid propellant concept references 15,19, and 20
UNCERTAINTY ANALYSIS The structural weight estimates, however, are more
A refined version of the HTP/NHMF concept with uncertain. This uncertainty is partially a function of the
additional weight savings achieved through modern lower fidelity and predictive capability of the structural
structural technologies was chosen as an example to weight estimation method used in preliminary sizing.
evaluate the effects of uncertainty in the sizing process Another factor in the uncertianty is in the estimates of
on total PBPS weight. A probabilistic study was the fixed weights (e.g. valves, ducting, etc.). Because
conducted to capture uncertainty in both the structural this uncertainty is signficantly greater, bounds of ±20%
weight and the propellant specific impulse, as these of the nominal structural weight estimate was chosen.
parameters are the primary drivers on system sizing to Since the actual structural weight and Isp values are
meet the fixed performance requirements. The specific most likely close to the nominal value, and because the
goals of the design study were as follows: likelihoods of errors being either high or low are likely
equal, the parameters were defined as normally
• Define reasonable bounds for uncertainty in the distributed random variables for the purposes of this
specific impulse and structural weight probailisitic design study. In order to generate the
• Bound the uncertainty in the total PBPS weight mean and standard deviation necessary to define these
that might result from variation in the specific variables, the nomial predictions were set as the means,
impulse and structural weight from their presumed and the standard deviations were chosen such that the
values predicted bounds in the uncertainties were set to
• Ensure that the specific impulse and structural enclose ± 3 standard deviations. An illustration of the
weight uncertainty does not result in an inability to random variable definition for Isp is shown in Figure 12.
create a sized design to meet the mission
requirements
The first step in the study involved establishing bounds
for the maximum expected uncertainty for the specific
impulse and structural weight estimates. Because of a
high confidence in the predicted propellant
performance, a small uncertainty bound was placed on
the nominal Isp predictions. This uncertainty bound was
set at ±2.5% of the calculated propellant Isp.
UNCLASSIFIED 10
11. UNCLASSIFIED
an unreasonable fuel mass requirement. Similar results
were obtained for the HTP/CINCH concept (i.e. the
Likelihood
weight was less than that of the current PSRE). As
should be expected from the deterministic results
shown in Table III, the other concepts showed
significant probability of weights greater than that of
the PSRE.
263.1 269.8 276.6 CANDIDATE CONCEPT EVALUATION
-2.5% Nominal +2.5% From a weight standpoint, the HTP/NHMF,
-3σ +3σ HTP/CINCH, and NTO/MMH gel concepts were all
Isp (sec) predicted to be comparable or superior to the baseline
PSRE. The CINCH and NHMF were especially
Figure 12: Specific Impulse Random Variable Definition promising because of the relatively high propellant
specific impulse values and the lower-weight spherical
After the specific impulse and structural mass were propellant tanks. As weight is often directly related to
defined as probability distributions, a Monte Carlo cost, these systems may also have lower acquisition
analysis was coupled with the PBPS sizing algorithm. costs.
In this analysis, the Monte Carlo simulation selected
10,000 discrete values of structural weight and specific Weight and cost are not the only discriminating factors,
impulse according to their respective probability however; technical risk is also a key consideration. All
distributions. The simulation then generated a sized of the concepts presented have some degree of
PBPS concept for each of the 10,000 cases. The developmental risk. The HTP concepts would need
resulting PBPS total mass outputs from the sizing technology development and validation of the oxidizer
algorithm were collected to produce a cumulative cooling system and the fuel catalysts, and the gel
distribution function (CDF). This CDF indicates the concept would need to demonstrate a feasible
likelihood that the total mass is less than a specified propellant distribution and valving system. The most
value. The CDF for PBPS total mass is shown in risky concepts, however, are the hybrid and solid
Figure 13. propellant concepts. The hybrid has two very difficult
technology challenges: proving that ignition delay can
1.00
be reduced to acceptable levels and demonstrating an
0.90
adequate HTP monopropellant thruster. The solid
0.80 75% probability < 510 lbm propellant concept must be shown capable of producing
0.70
the precise positioning control with a multi-tiered
0.60
Probability
attitude control propulsion system and must also use
0.50
99.79% probability < 550 lbm aggressive materials technologies to keep the weight of
0.40
the system reasonable.
0.30
0.20 Based on these considerations, the HTP/NHMF and
0.10 HTP/CINCH concepts appear to offer the most promise
0.00 for the PBPS application. This study has indicated that
400 420 440 460 480 500 520 540 560
the systems can be produced at a weight (and possibly
PBPS Total Mass (lbm)
cost) lower than that of the current MM III PSRE, even
considering uncertainty in the sizing presumptions. The
Figure 13: PBPS Total Mass Cumulative Distribution weight may be further reduced if other structural
Function technologies such as an isogrid shell and composite
The probabilistic analysis shows that likelihood of the interior structure are implemented. In addition to their
PBPS weight being less than 550 lbm for the presumed weight advantage, the systems also appear to be
uncertainty in structural mass and specific impulse is feasible in terms of technical risk, especially as
nearly 100%. This result indicates that the HTP/NHMF contrasted to the solid and hybrid propellant concepts
PBPS concept is certain to weigh less than the current presented.
MM III post boost system given the assumptions for
structural weight and Isp made in the study. The results CONCLUSIONS
also indicate that a HTP/NHMF PBPS can successfully From this study, it is apparent that several “green”
be sized in the entire presumed range of uncertainties, propellants are adequate for the PBPS application. The
i.e., no combination of structural weight and Isp result in most promising green propellant formulations appear to
UNCLASSIFIED 11
12. UNCLASSIFIED
be HTP/CINCH and HTP/NHMF. The propellants’ for hypergolic ignition with HTP and in the
performance, which approaches that of the NTO/MMH, demonstration of a low-weight oxidizer cooling system.
results in sized PBPS concepts that have equivalent Based on these results, it is clear that in addition to their
performance and weigh less than current Minuteman III inherent advantages in storage, personnel safety, and
PSRE. These propellant formulations also have a handling, green propellants offer the necessary
reasonable level of technical risk, mostly residing in the performance required for land-based strategic ICBM
development of soluble fuel catalysts that are required post-boost propulsion systems.
REFERENCES
1 15
“Dimethyl-2-azidoethylamine, Available Data and Recommended German, Branscome, Frits, Yiakas, et.al., “Next Generation ICBM
Additional Data”, Johnson Space Center White Sands Test Post Boost Propulsion System”, Proposal to the 2000 AIAA
Facility, 28 April 2000. MSTC Graduate Missile Design Competition, 5 June 2000.
2 16
Funk, J.E. and Rusek, J., “Assessment of United States Navy Haag, G.S., Paul, M., Brown, R., Gibbon, D., Richardson, G., “An
Block 0 NHMF/RGHP Propellants”, 2 nd International Hydrogen Experimental Investigation of ‘Rocket Grade’ Hydrogen
Peroxide Propulsion Conference, 7-10 November 1999. Peroxide,” 2nd International Hydrogen Peroxide Propulsion
Conference, 7-10 November 1999.
3
Meade, C.J., Lormand, B., and Purcell, N., “ Status of Non-Toxic
17
Hypergolic Miscible Fuel Development at NAWCWD China “The Decomposition of H2O2”,
Lake”, 2nd International Hydrogen Peroxide Propulsion http://www.uiowa.edu/~c004016b/exp10/lec10/sld007.htm,
Conference, 7-10 November 1999. University of Iowa Website, 27 May 2000.
4 18
“1st Hydrogen Peroxide Propulsion Workshop”, “Trident II D-5 Fleet Ballistic Missile”,
http://www.ee.surrey.ac.uk/SSC/H2O2CONF/index.htm, Surrey http://www.fas.org/nuke/guide/usa/slbm/d-5.htm, Federation of
Space Centre website, 20 April 2000. American Scientists Website, 28 May 2000.
19
5 “Minuteman Propulsion System Handbook”, ICBM SE/TA
“Niosh Pocket Guide To Chemical Hazards”,
Program, Strategic Systems Division, TRW, inc., September
http://www.cdc.gov/niosh/npg/pgintrod.html, Center for Disease
1997.
Control Website, 28 May 2000.
20
6 Photographs of PSRE on Display at SAC Museum, Ashland, NE,
Anderson, W., “Low Cost Propulsion Using a High-Density,
from Brian York, curator, January 2000.
Storable, and Clean Propellant Combination”, NASA Marshall
Space Flight Center.
7
Palaszewski, B., “Gelled Liquid Hydrogen: A White Paper”, NASA
Lewis Research Center.
8
Whitehead, J.C., “Hydrogen Peroxide Propulsion for Smaller
Satellites”, Lawrence Livermore National Laboratory.
9
Sarner, S.F., Propellant Chemistry, Reinhold, New York, 1966.
10
Siegel, B. and Schieler, L., Energetics of Propellant Chemistry, J.
Wiley and Sons, New York, 1964.
11
Sutton, Rocket Propulsion Elements, An Introduction to the
Engineering of Rockets, J. Wiley and Sons, New York, Sixth
Edition, 1992.
12
Keith, E., “The Peroxide Counter Revolution: Replacing Toxic
Propellants in Space”, International Space Propulsion
Incorporated.
13
Palaszewski, B. “Propellant Technologies: A Persuasive Wave of
Future Propulsion Benefits”, NASA Glenn Research Center.
14
Mavris, D.N., DeLaurentis, D.A., "An Integrated Approach to
Military Aircraft Selection and Concept Evaluation," 1st AIAA
Aircraft Engineering, Technology, and Operations Congress, Los
Angeles, CA, September 19-21, 1995. AIAA-95-3921
UNCLASSIFIED 12