This document provides an overview of intelligent sensor solutions for the power industry, focusing on applications in coal fired power plants. It discusses challenges in the industry around efficiency, emissions monitoring, and corrosion protection. It then focuses on specific applications in coal fired power plants, including coal handling, the combustion process, deNOx systems, dust removal, wet flue gas desulfurization, and continuous emissions monitoring. SICK sensors and monitoring solutions are presented for measuring parameters like CO, O2, NOx, dust and particulate matter at various points in the coal combustion and emissions control process.
Magnetic level indicators provide highly visible indication of level with or without signal outputs monitoring tail and vessel level. The term bridle is used to describe a vertical pipe connected to the side of a storage tank or process vessel, most often with side-to-side or side-to-bottom connections. Because the fluid inside the bridle rises and falls equally with the level of fluid inside the tank or vessel, bridles have been adapted for level measurement use on a broad scale.
The document describes a solar tracking system called the sonnen_system that is designed to maximize solar energy collection. It precisely tracks the sun's movement throughout the day to maintain an optimal angle for solar panels, increasing energy yields by up to 45% compared to fixed systems. The sonnen_system uses a robust design and precise controls to reliably produce electricity even in extreme weather conditions, and its modular design allows for monitoring and maintenance from anywhere in the world.
Dual chamber liquid level measuring system with magnetic level indication and guided wave radar combined into a single assembly.
The VEGAMAG 62 series combination magnetic level indicator and bypass bridle chamber provides the benefits of both visual indication and process control by using the proven technology of the VEGAFLEX to provide the most complete visual and guided microwave radar package in the industry. The VEGAMAG 62 can be configured to mount to most standard tank process connections as well as applications where interface measurements are needed.
Portable flow meter for measurement of compressed air, gases, and heat quanti...Classic Controls, Inc.
The FLUXUS G601 CA Energy is the ideal tool for carrying out complete energy efficiency tasks in the industry as well as within facility management by allowing the measurement of compressed air flow rates as well as the monitoring of thermal energy quantities and the flow rate determination of any kind of liquid or gaseous media with just one device.
VEGA Pressure & Level Measurement Metal Processing Industry ApplicationsThorne & Derrick UK
VEGA provides measurement solutions for the demanding conditions in the metal processing industry. Their plics modular system allows for individual combinations of sensors, fittings, electronics and housings to meet technical and economic needs. Application examples show how VEGA instruments reliably measure levels, pressures and other process variables in challenging environments like mining, steel production, and smelting under high temperatures, dust, noise and abrasive conditions.
A complete range of Instruments for the Solar IndustryAlexandre Ferrete
Installing Meteorological instrumentation to monitor
environmental parameters such as solar radiation, wind loading,
precipitation, temperature and humidity, provides solar park
operators with essential data to identify performance related
issues and maintenance factors affecting efficiency.
MaxiMet and MetPak weather stations measure these
parameters to monitor park efficiency. These include ISO9060
standard solar radiation sensors for park efficiency against
energy forecasts, wind speed for panel loading which helps
avoid panel damage, precipitation to assist with maintenance
scheduling and external temperature sensors to monitor
individual panel efficiency.
Yokogawa has a long history of supplying process gas chromatographs to the oil & gas, refining and petrochemical industries around the world. The new process GC that meets the ever growing demands for analytical reliability and precision while improving the total cost-of ownership through built-in automated maintenance functions never seen before.
From the innovative 12-inch color touch screen HMI to the powerful predictive diagnostics, the GC8000 is truly a process GC for the 21st century. But the GC8000 is not just all about new electronics; it also brings a number of important innovations in gas chromatograph analytical capabilities. For the first time, parallel chromatography is made practical with the introduction of the GC Module (GCM) concept. By setting up virtual GCs within a single analyzer, all chromatograph settings, displays, and data are truly segregated for easy understanding and maintenance. There are even built-in graphical overview screens showing each of the individual GC Modules.
The GC8000 sets new standards for process gas chromatography while at the same time offering hardware and electronics that are recognized for robust and reliable operation.
Kamstrup - Heat Meters & Water Meters Ultrasonic (RHI Compliant MID Class 2 H...Thorne & Derrick UK
This document summarizes Kamstrup's role as a leading provider of intelligent energy and water metering solutions. It discusses how Kamstrup helps utilities optimize operations and make smarter decisions using collected meter data. It also outlines major trends in energy/water and how Kamstrup addresses challenges of cost constraints, environmental pressures, and market competition through innovative products and services.
Magnetic level indicators provide highly visible indication of level with or without signal outputs monitoring tail and vessel level. The term bridle is used to describe a vertical pipe connected to the side of a storage tank or process vessel, most often with side-to-side or side-to-bottom connections. Because the fluid inside the bridle rises and falls equally with the level of fluid inside the tank or vessel, bridles have been adapted for level measurement use on a broad scale.
The document describes a solar tracking system called the sonnen_system that is designed to maximize solar energy collection. It precisely tracks the sun's movement throughout the day to maintain an optimal angle for solar panels, increasing energy yields by up to 45% compared to fixed systems. The sonnen_system uses a robust design and precise controls to reliably produce electricity even in extreme weather conditions, and its modular design allows for monitoring and maintenance from anywhere in the world.
Dual chamber liquid level measuring system with magnetic level indication and guided wave radar combined into a single assembly.
The VEGAMAG 62 series combination magnetic level indicator and bypass bridle chamber provides the benefits of both visual indication and process control by using the proven technology of the VEGAFLEX to provide the most complete visual and guided microwave radar package in the industry. The VEGAMAG 62 can be configured to mount to most standard tank process connections as well as applications where interface measurements are needed.
Portable flow meter for measurement of compressed air, gases, and heat quanti...Classic Controls, Inc.
The FLUXUS G601 CA Energy is the ideal tool for carrying out complete energy efficiency tasks in the industry as well as within facility management by allowing the measurement of compressed air flow rates as well as the monitoring of thermal energy quantities and the flow rate determination of any kind of liquid or gaseous media with just one device.
VEGA Pressure & Level Measurement Metal Processing Industry ApplicationsThorne & Derrick UK
VEGA provides measurement solutions for the demanding conditions in the metal processing industry. Their plics modular system allows for individual combinations of sensors, fittings, electronics and housings to meet technical and economic needs. Application examples show how VEGA instruments reliably measure levels, pressures and other process variables in challenging environments like mining, steel production, and smelting under high temperatures, dust, noise and abrasive conditions.
A complete range of Instruments for the Solar IndustryAlexandre Ferrete
Installing Meteorological instrumentation to monitor
environmental parameters such as solar radiation, wind loading,
precipitation, temperature and humidity, provides solar park
operators with essential data to identify performance related
issues and maintenance factors affecting efficiency.
MaxiMet and MetPak weather stations measure these
parameters to monitor park efficiency. These include ISO9060
standard solar radiation sensors for park efficiency against
energy forecasts, wind speed for panel loading which helps
avoid panel damage, precipitation to assist with maintenance
scheduling and external temperature sensors to monitor
individual panel efficiency.
Yokogawa has a long history of supplying process gas chromatographs to the oil & gas, refining and petrochemical industries around the world. The new process GC that meets the ever growing demands for analytical reliability and precision while improving the total cost-of ownership through built-in automated maintenance functions never seen before.
From the innovative 12-inch color touch screen HMI to the powerful predictive diagnostics, the GC8000 is truly a process GC for the 21st century. But the GC8000 is not just all about new electronics; it also brings a number of important innovations in gas chromatograph analytical capabilities. For the first time, parallel chromatography is made practical with the introduction of the GC Module (GCM) concept. By setting up virtual GCs within a single analyzer, all chromatograph settings, displays, and data are truly segregated for easy understanding and maintenance. There are even built-in graphical overview screens showing each of the individual GC Modules.
The GC8000 sets new standards for process gas chromatography while at the same time offering hardware and electronics that are recognized for robust and reliable operation.
Kamstrup - Heat Meters & Water Meters Ultrasonic (RHI Compliant MID Class 2 H...Thorne & Derrick UK
This document summarizes Kamstrup's role as a leading provider of intelligent energy and water metering solutions. It discusses how Kamstrup helps utilities optimize operations and make smarter decisions using collected meter data. It also outlines major trends in energy/water and how Kamstrup addresses challenges of cost constraints, environmental pressures, and market competition through innovative products and services.
The document describes the Palomar Technologies 6500 Die Bonder, which is a precision assembly machine for semiconductor packaging. It can achieve placement accuracy of +/- 1.5 microns and has features like a 6 position tool turret, programmable eutectic pulse heating, and large work area. The die bonder is versatile and can be used for applications like hybrid modules, MEMS components, and optoelectronic packaging. Palomar also offers related equipment and automated assembly lines integrating die bonders, fluid dispensers, and other tools.
Pentair's Thermal Management segment provides electric thermal solutions for industrial processes, buildings, and infrastructure. It manages heat through products like heat tracing, insulation, temperature monitoring and control systems. The segment has over 2,500 employees worldwide serving customers in industries like oil/gas, power, and general industry through the entire heat management project lifecycle from engineering to maintenance. Thermal Management has a long history and is a global leader in electric heat tracing technology.
The DUSTHUNTER C200 is a type-approved measuring device which combines the advantages
of the measuring principles of transmittance and forward scattered light. It is, therefore, ideal for
measuring very low to high dust concentrations. Automatic self-alignment optimizes the position
of the measuring beam and prevents incorrect measurement. An automated check of the zero
and reference point as well as a contamination check are on board in the device.
For Electrical and Maintenance engineers working in Manufacturing and Hospitality sector, the challenge is tosupervise plant-wide energy utilisation and manage their electric infrastructure in a systematic, optimised way.
Janitza GmbH is a globally renowned and leading supplier of energy efficiency systems. Their digital energy meters, power quality analysers, digital measurement equipment, universal-measurement devices, power factor controller, peak demand management systems etc. are well acceptedall over the world.
Kamstrup RHI Compliant Heat Meters & Thermal Energy Measurement - Multical 60...Thorne & Derrick UK
MULTICAL 602 is an energy calculator that measures heat, cooling, and combined heat/cooling. It connects to flow sensors and temperature sensors to calculate energy usage. It has a long battery life, stores consumption data daily/hourly, and has various communication options. Its info codes and data loggers monitor the system for errors and allow troubleshooting. It provides accurate measurements over its lifetime to optimize building operations and energy billing.
Understanding Manifolds Technology and Selection Yokogawa1
To facilitate and simplify the installation of pressure transmitters you need (valve) manifolds. A manifold will allow a calibration or a change to the pressure transmitter without the necessity of plant shutdown.
Manifold selection can be quite difficult as there are several types. Various aspects must be taken into consideration, such as process conditions including the metallurgy requirements, turndown requirements, accuracy, and installation requirements.
Join this webinar to better understand which manifolds you should use for specific applications and conditions.
You will learn:
A brief history of manifolds
An overview of the different types of manifolds that are available
The advantages, disadvantages, and application considerations you should consider when selecting a manifold
The Palomar Technologies 3800 Die Bonder is a fully automatic, precision microelectronics assembly system. It features high flexibility with up to three channels for adhesive dispensing, component placement, and die attach operations. The 3800 Die Bonder provides a large 710 square inch work area and high placement accuracy of 7 microns. It includes options for eutectic die attach, flip chip bonding, dispensing, tape feeders, and in-line assembly lines. The system also offers versatile programming and operation tools including pattern recognition software.
Process Analyzer Sampling Systems SimplifiedYokogawa1
Joe Goh from Yokogawa Corporation presented a webinar on process analyzer sampling systems. He discussed key sampling system components, common system designs, and best practices for operation and maintenance. The webinar covered topics like shelter design considerations, hazardous area classification, sample conditioning systems, and project management. The goal was to simplify understanding of process analyzer sampling and help attendees properly design, install, and optimize these critical systems.
The ultrasonic heating and cooling energy meter SKU-03 is designed to measure and record heating and cooling energy consumption separately. It can be used for commercial metering of energy usage in residential and commercial buildings. The meter uses ultrasonic flow measurement and has features such as separate registers for heating and cooling, user-defined display parameters, pulse inputs/outputs, M-Bus and wireless communication, tariff functions, and data logging of hourly, daily and monthly consumption values. It has an accuracy of class 2 and measures energy in units such as kWh, MWh and GJ.
Kamstrup RHI Compliant Heat Meters & Thermal Energy Measurement - Multical 40...Thorne & Derrick UK
The document provides information about the MULTICAL® 402 ultrasonic heat and cooling meter. It can measure energy consumption with temperatures from 2-160°C and has a measurement accuracy of ±(0.15 + 2/ΔΘ)%. The meter consists of a calculator, flow sensor and two temperature sensors. It has a battery lifetime of up to 16 years and can be remotely read via wireless M-Bus or radio.
CAREL's Enrico Boscaro illustrates at ASHRAE Malaysia seminar the potentials of Indirect Evaporative Cooling technology as an energy savings instrument in cooling applications, in particular for the Make up Air handlers sector.
The H4000 is a Woltmann-type water meter designed for measuring bulk flows of cold potable water for commercial and industrial applications. It is accurate and robust, constructed from high-quality corrosion-resistant materials. It is available in sizes from 0.35 m3/h to 2000 m3/h and operates at temperatures up to 50°C and pressures up to 16 bar. The H4000 can provide pulse communications and integrate with intelligent meter reading systems to provide utilities with water management information.
Thermoelectric generators convert heat directly into electricity using a fuel source for heat, a hermetically sealed thermopile, and cooling fins. These generators are a positive and cost effective solution for remote power requirements, having operational and cost benefits over batteries and solar sources for many applications.
Manage power consumption, cooling delivery, and temperature set points at a rack level
Reduce your cooling and electrical costs by up to 50%
Reduce the costs to plan, build, and implement your new facility by up to 80%
Grow horizontally—from 1 to 100 units—without disrupting existing operations?
Can be installed or Re-Located anywhere with the only requirements being power and network connectivity
Provide a complete turnkey solution within weeks vs. years.
How to hande greasy waste in industrial kitchensDillen Valerie
Learn how Raychem heat-trace offers a perfect alternative to passive grease interceptors, following new building design trends to reduce interceptors. Heat-tracing is a reliable and lower cost alternative.
The KNX gateway for Fronius inverters provides a simple solution to transfer all relevant data from inverters to KNX.
It allows integrators to take advantage of a fully integrated solar panel inverter, the data can be used for monitoring, trending or to trigger specific action in the KNX installation.
Hecu Sistema is the CAREL solution for commercial refrigeration, designed for high energy efficiency condensing units that use either traditional HFC refrigerants or natural refrigerants such as CO2.
The system’s distinctive features include the use of DC inverter technology and real-time synchronisation with the refrigeration units. Hecu sistema meets the requirements of the latest environmental sustainability standards relating to energy consumption (Eco-design directive) and the use of low GWP refrigerants (F-Gas regulation). Stable control means high-quality food preservation and a drastic reduction in waste.
Hecu sistema is also compatible with all CAREL supervisors, which can monitor each individual system or groups of systems, and offer dashboards to simplify interpretation and analysis of system operation.
The document provides details on a study conducted by Gastec at CRE Ltd for the Department of Energy and Climate Change (DECC) on heat metering for the Renewable Heat Incentive (RHI) scheme. The study evaluated options for metering renewable heat generated by technologies such as biomass boilers, heat pumps, biogas, and solar thermal systems. It assessed choices for meters and their maintenance, automatic data collection methods, recommended data reporting, and costs of metering. Key findings included that meters should comply with European directives, data collection could be done through physical reads or remote methods like AMR, and costs vary depending on technology and data collection method.
The document provides a basic technical description of an ultrasonic heat meter. It details the meter's safety requirements, operating principles, installation instructions, and technical specifications. The meter measures thermal energy consumption in closed heating and cooling systems. It calculates heat energy based on flow rate and temperature difference measurements from ultrasonic sensors and Pt500 temperature sensors. The meter achieves a class 2 accuracy level for energy and volumetric flow measurements.
The document provides information on storage and conveyor systems. It discusses challenges around flexibility and cost-efficiency. It then provides examples of sensor applications for various conveyor and storage systems, including tote conveying, pallet conveyor, pallet transfer car, storage and retrieval system (driving and lifting unit), and more. For each application, it describes how sensors can be used for tasks like presence detection, gap monitoring, speed measurement, positioning, safety, and identification. A variety of sensor types are highlighted, including photoelectric, inductive, laser, and vision sensors.
Meggitt is a leading provider of sensing and monitoring solutions for extreme environments like gas turbines. It offers complete solutions for protecting, monitoring, and optimizing turbine performance, including hardware, software, sensors, and data visualization tools. Meggitt's products monitor critical parameters like vibration, pressure, speed, and temperature to enable condition-based maintenance and reduce downtime.
The document describes the Palomar Technologies 6500 Die Bonder, which is a precision assembly machine for semiconductor packaging. It can achieve placement accuracy of +/- 1.5 microns and has features like a 6 position tool turret, programmable eutectic pulse heating, and large work area. The die bonder is versatile and can be used for applications like hybrid modules, MEMS components, and optoelectronic packaging. Palomar also offers related equipment and automated assembly lines integrating die bonders, fluid dispensers, and other tools.
Pentair's Thermal Management segment provides electric thermal solutions for industrial processes, buildings, and infrastructure. It manages heat through products like heat tracing, insulation, temperature monitoring and control systems. The segment has over 2,500 employees worldwide serving customers in industries like oil/gas, power, and general industry through the entire heat management project lifecycle from engineering to maintenance. Thermal Management has a long history and is a global leader in electric heat tracing technology.
The DUSTHUNTER C200 is a type-approved measuring device which combines the advantages
of the measuring principles of transmittance and forward scattered light. It is, therefore, ideal for
measuring very low to high dust concentrations. Automatic self-alignment optimizes the position
of the measuring beam and prevents incorrect measurement. An automated check of the zero
and reference point as well as a contamination check are on board in the device.
For Electrical and Maintenance engineers working in Manufacturing and Hospitality sector, the challenge is tosupervise plant-wide energy utilisation and manage their electric infrastructure in a systematic, optimised way.
Janitza GmbH is a globally renowned and leading supplier of energy efficiency systems. Their digital energy meters, power quality analysers, digital measurement equipment, universal-measurement devices, power factor controller, peak demand management systems etc. are well acceptedall over the world.
Kamstrup RHI Compliant Heat Meters & Thermal Energy Measurement - Multical 60...Thorne & Derrick UK
MULTICAL 602 is an energy calculator that measures heat, cooling, and combined heat/cooling. It connects to flow sensors and temperature sensors to calculate energy usage. It has a long battery life, stores consumption data daily/hourly, and has various communication options. Its info codes and data loggers monitor the system for errors and allow troubleshooting. It provides accurate measurements over its lifetime to optimize building operations and energy billing.
Understanding Manifolds Technology and Selection Yokogawa1
To facilitate and simplify the installation of pressure transmitters you need (valve) manifolds. A manifold will allow a calibration or a change to the pressure transmitter without the necessity of plant shutdown.
Manifold selection can be quite difficult as there are several types. Various aspects must be taken into consideration, such as process conditions including the metallurgy requirements, turndown requirements, accuracy, and installation requirements.
Join this webinar to better understand which manifolds you should use for specific applications and conditions.
You will learn:
A brief history of manifolds
An overview of the different types of manifolds that are available
The advantages, disadvantages, and application considerations you should consider when selecting a manifold
The Palomar Technologies 3800 Die Bonder is a fully automatic, precision microelectronics assembly system. It features high flexibility with up to three channels for adhesive dispensing, component placement, and die attach operations. The 3800 Die Bonder provides a large 710 square inch work area and high placement accuracy of 7 microns. It includes options for eutectic die attach, flip chip bonding, dispensing, tape feeders, and in-line assembly lines. The system also offers versatile programming and operation tools including pattern recognition software.
Process Analyzer Sampling Systems SimplifiedYokogawa1
Joe Goh from Yokogawa Corporation presented a webinar on process analyzer sampling systems. He discussed key sampling system components, common system designs, and best practices for operation and maintenance. The webinar covered topics like shelter design considerations, hazardous area classification, sample conditioning systems, and project management. The goal was to simplify understanding of process analyzer sampling and help attendees properly design, install, and optimize these critical systems.
The ultrasonic heating and cooling energy meter SKU-03 is designed to measure and record heating and cooling energy consumption separately. It can be used for commercial metering of energy usage in residential and commercial buildings. The meter uses ultrasonic flow measurement and has features such as separate registers for heating and cooling, user-defined display parameters, pulse inputs/outputs, M-Bus and wireless communication, tariff functions, and data logging of hourly, daily and monthly consumption values. It has an accuracy of class 2 and measures energy in units such as kWh, MWh and GJ.
Kamstrup RHI Compliant Heat Meters & Thermal Energy Measurement - Multical 40...Thorne & Derrick UK
The document provides information about the MULTICAL® 402 ultrasonic heat and cooling meter. It can measure energy consumption with temperatures from 2-160°C and has a measurement accuracy of ±(0.15 + 2/ΔΘ)%. The meter consists of a calculator, flow sensor and two temperature sensors. It has a battery lifetime of up to 16 years and can be remotely read via wireless M-Bus or radio.
CAREL's Enrico Boscaro illustrates at ASHRAE Malaysia seminar the potentials of Indirect Evaporative Cooling technology as an energy savings instrument in cooling applications, in particular for the Make up Air handlers sector.
The H4000 is a Woltmann-type water meter designed for measuring bulk flows of cold potable water for commercial and industrial applications. It is accurate and robust, constructed from high-quality corrosion-resistant materials. It is available in sizes from 0.35 m3/h to 2000 m3/h and operates at temperatures up to 50°C and pressures up to 16 bar. The H4000 can provide pulse communications and integrate with intelligent meter reading systems to provide utilities with water management information.
Thermoelectric generators convert heat directly into electricity using a fuel source for heat, a hermetically sealed thermopile, and cooling fins. These generators are a positive and cost effective solution for remote power requirements, having operational and cost benefits over batteries and solar sources for many applications.
Manage power consumption, cooling delivery, and temperature set points at a rack level
Reduce your cooling and electrical costs by up to 50%
Reduce the costs to plan, build, and implement your new facility by up to 80%
Grow horizontally—from 1 to 100 units—without disrupting existing operations?
Can be installed or Re-Located anywhere with the only requirements being power and network connectivity
Provide a complete turnkey solution within weeks vs. years.
How to hande greasy waste in industrial kitchensDillen Valerie
Learn how Raychem heat-trace offers a perfect alternative to passive grease interceptors, following new building design trends to reduce interceptors. Heat-tracing is a reliable and lower cost alternative.
The KNX gateway for Fronius inverters provides a simple solution to transfer all relevant data from inverters to KNX.
It allows integrators to take advantage of a fully integrated solar panel inverter, the data can be used for monitoring, trending or to trigger specific action in the KNX installation.
Hecu Sistema is the CAREL solution for commercial refrigeration, designed for high energy efficiency condensing units that use either traditional HFC refrigerants or natural refrigerants such as CO2.
The system’s distinctive features include the use of DC inverter technology and real-time synchronisation with the refrigeration units. Hecu sistema meets the requirements of the latest environmental sustainability standards relating to energy consumption (Eco-design directive) and the use of low GWP refrigerants (F-Gas regulation). Stable control means high-quality food preservation and a drastic reduction in waste.
Hecu sistema is also compatible with all CAREL supervisors, which can monitor each individual system or groups of systems, and offer dashboards to simplify interpretation and analysis of system operation.
The document provides details on a study conducted by Gastec at CRE Ltd for the Department of Energy and Climate Change (DECC) on heat metering for the Renewable Heat Incentive (RHI) scheme. The study evaluated options for metering renewable heat generated by technologies such as biomass boilers, heat pumps, biogas, and solar thermal systems. It assessed choices for meters and their maintenance, automatic data collection methods, recommended data reporting, and costs of metering. Key findings included that meters should comply with European directives, data collection could be done through physical reads or remote methods like AMR, and costs vary depending on technology and data collection method.
The document provides a basic technical description of an ultrasonic heat meter. It details the meter's safety requirements, operating principles, installation instructions, and technical specifications. The meter measures thermal energy consumption in closed heating and cooling systems. It calculates heat energy based on flow rate and temperature difference measurements from ultrasonic sensors and Pt500 temperature sensors. The meter achieves a class 2 accuracy level for energy and volumetric flow measurements.
The document provides information on storage and conveyor systems. It discusses challenges around flexibility and cost-efficiency. It then provides examples of sensor applications for various conveyor and storage systems, including tote conveying, pallet conveyor, pallet transfer car, storage and retrieval system (driving and lifting unit), and more. For each application, it describes how sensors can be used for tasks like presence detection, gap monitoring, speed measurement, positioning, safety, and identification. A variety of sensor types are highlighted, including photoelectric, inductive, laser, and vision sensors.
Meggitt is a leading provider of sensing and monitoring solutions for extreme environments like gas turbines. It offers complete solutions for protecting, monitoring, and optimizing turbine performance, including hardware, software, sensors, and data visualization tools. Meggitt's products monitor critical parameters like vibration, pressure, speed, and temperature to enable condition-based maintenance and reduce downtime.
The document is an industrial training report submitted by Paras Pratap during their internship at C&S Electric Ltd. It includes an introduction to the company profile, details about the training such as the plant layout and processes, and information about ring main units (RMUs) including their parts, features, types, and the tank assembly process. The report provides an overview of the internship experience and lessons learned about medium voltage switchgear manufacturing.
The document provides information about an industrial training report completed by Paras Pratap at C&S Electric Ltd. It includes an introduction to the company, which is a leading manufacturer of electrical equipment in India. It then discusses the trainee's experience, including an overview of the plant layout and processes, an introduction to ring main units produced by C&S, and details about tank assembly and testing procedures.
SICK provides intelligent sensor solutions to address the key challenges of the cement industry. These challenges include ensuring high process efficiency and product quality, monitoring emissions to comply with regulations, and optimizing material flow. SICK's broad product portfolio includes sensors for emission measurement, quality control, machine safety, and plant monitoring. SICK also offers services like consulting, installation, and maintenance to support cement customers throughout the lifecycle.
This document provides information about a double axis solar tracking system produced by SABO. It summarizes the key specifications and features of two solar tracker models, the SR 80 SQM and SR 90 SQM. The tracking systems are designed to increase solar panel efficiency and energy production through automatic dual-axis movement that follows the sun's path. The document also outlines the structural, mechanical, and safety characteristics of the trackers.
IRJET- Wireless Gas Leak Detection and Localization for Remote Vehicles using...IRJET Journal
This document describes a wireless gas leak detection and localization system for remote vehicles using a wireless sensor network. The system uses a PIC microcontroller interfaced with an MQ-6 gas sensor to detect inflammable gases and an LM35 temperature sensor to monitor engine temperature. If a gas leak is detected above a certain threshold, the system triggers a buzzer and sends an SMS via a wireless transceiver. It can also detect increases in temperature that may indicate a fire. The system aims to remotely detect and locate gas leaks in vehicles to prevent injuries, deaths and environmental damage.
The Ingold 6800 G O2 sensor series for gas measurement provides high operational availability together with excellent measurement performance. Without the need for an expensive gas sample conditioning, the sensor can be installed directly in the process and sensor maintenance or replacement can be performed without process interruption. Mettler-Toledo Ingold offers a unique easy-to-use and reliable solution for challenging applications like N2 blanketing, inertization and off-gas monitoring in ex or non-ex applications.
The document discusses efficient solutions for traffic systems, focusing on applications for roads. It describes how SICK solutions are used for (1) monitoring electronic toll collection through 3D laser scanning and automation light grids to classify vehicles, (2) red light and speed monitoring using laser-based sensors, and (3) ensuring traffic safety with solutions for clearance measurement, hot spot detection, and more.
The document describes an innovative technology called MetrySense-4000 that monitors power line insulator string contamination through partial discharge sensors. It detects contamination levels in real-time to help utilities reduce costs by washing insulators only where needed and avoiding power interruptions from flashovers. The system's wireless sensor units have a long battery life, low power use, and reliable connectivity to provide utilities with an overall vision of contamination levels on their transmission networks.
Project INDUSTRIAL AUTOMATION AND SECURITY SYSTEMSoumya Saswati
This document describes a project to develop a PC-based industrial automation and security system. The system uses a microcontroller to control loads, appliances, and security in industries through a PC and touch screen interface. It has three modules: load control, fire alarm, and security locking using RFID. The system automates industrial processes to increase productivity, quality and consistency while improving security. Hardware components like the transformer, regulator, rectifier, and filter process power for the microcontroller and other components.
Turnkey Solutions – the key to successful projects
----------------------------------------------------------------
EPC Solutions has all it takes to design, construct, and operate turnkey electrical substation solutions that efficiently support the reliable supply of electrical power on all voltage levels: decades of practical experience as a contractor and equipment manufacturer and a vast number of successfully completed projects all over the world, unparalleled expertise in all transmission processes, and proven excellence in project management. A distinguished tradition of innovation in power engineering, customized financing solutions, and outstanding quality standards in all production facilities worldwide round out the picture.
EPCS turnkey solutions for high-voltage substations incorporate the strong performance of one of the world’s leading engineering companies and one-stop supplier of power transmission products, solutions, and services. The scope of services comprises consulting, project management, system planning, engineering, commissioning, and comprehensive after-sales support. Centers of competence and branches all over the world create local value and ensure that EPCS experts are within close reach of every project.Customers worldwide benefit from numerous advantages of high-voltage substations from EPCS:
>One-stop approach comprising all technical, financial, and ecological aspects of the station’s entire life cycle
>Customized solutions based on proven EPCS technologies, even for the most challenging demands
>Freedom from coordination efforts and minimized financial and technical risk
GILL Instruments' and MEASNET - WindObserver, WindMaster, WindMaster ProAlexandre Ferrete
Gill Instruments produces environmental and industrial monitoring solutions. This document discusses Gill wind measurement products that meet the requirements of MEASNET, an organization that ensures high quality wind energy measurements. Gill's WindObserver and WindMaster ultrasonic anemometers have been tested and meet MEASNET's standards for linearity. In 2016, MEASNET requirements will include providing vertical wind speed measurements, and Gill will test its products to meet the new standards. MEASNET certification is required for wind turbine site instrumentation where financial backers require validated wind data.
- The document is a price list from Siemens Ltd. for their Betagard electrical installation products effective September 1st, 2016.
- It includes miniature circuit breakers, circuit breakers, isolators, residual current circuit breakers, distribution boards, and other modular devices.
- The price list provides product reference numbers, unit prices, module widths, standard packaging quantities, and specifications for each item.
The document discusses position and motion sensors sold by Electromate. It describes Electromate as a sales and service provider for sensors manufactured by FRABA Group, including absolute rotary encoders, linear sensors, and inclinometers. The document provides an overview of FRABA Group's products, technologies, applications, and global presence.
ROTORK SOLDO CONTROL SW LIMIT SWITCH BOX | YTC INDIAYTC INDIA
"Rotork Soldo Control SW Heavy-duty limit switch boxes, designed for hazardous areas, provide a visual and electrical remote position feedback on automated valves. Available in 316 stainless steel, the explosion proof enclosure matches the Ex d IIC T6 standards. The SW limit switch box serie, thanks to its large inner volume able to host up to 6 switches and spare pass through terminals and the four cable entries either metrics or imperial, provide a highly customizable solution meeting a wide range of applications. These including, but not limited to, the Oil and Gas, both onshore and off shore, and Petrochemical industries.
For any Enquiry Call Us: +91-11-2201-4325, For Bulk Order Email at : info@ytcindia.com, Our Website :- www.ytcindia.com"
This document describes a mobile sniffer and jammer system that detects the use of mobile phones in restricted areas like exam halls and hospitals. It consists of an RF detector, PIC microcontroller, GSM module, LCD display, and telescopic antenna. The PIC16F877A microcontroller monitors the RF level detected by the antenna and sends a warning message via the SIM900 GSM module if the level increases, also displaying it on the LCD. The circuit was designed using DIPTRACE and fabricated on a PCB with surface mount components soldered into place. The mobile sniffer system was able to successfully detect mobile signals and send alerts as required.
Leviton offers submetering solutions that provide accurate energy usage data to help buildings reduce costs through energy conservation and efficiency efforts. Submeters allow tracking of tenant, equipment, and department energy use to identify savings opportunities. They also support green building initiatives and compliance with energy mandates. Leviton offers a full line of revenue-grade submeters that integrate with building automation systems and provide long-term savings of 15-20% through increased accountability and efficiency.
Energy in offshore living quarters is mainly used for lighting, air-conditioning, ventilation, heating,
refrigration, lifts and motors. Whether these quarters already exists or to be built, there are
great opportunities to obtain their energy performance through targeted initiatives, upgrades
and retrofitting.
To meet the mandatory requirements for energy saving, EPC contractors for offshore living quarters
must comply with efficiency improvement regulations.
Similar to Efficient Solutions For The Power Industry (20)
This document provides contact and location information for ROTRONIC Instrument Corp. and its subsidiaries and partners worldwide. ROTRONIC is a Swiss-owned company with headquarters in Switzerland and subsidiaries across Europe, North America, Asia, and elsewhere. Contact information is provided for ROTRONIC's offices and representatives in Switzerland, Germany, France, Italy, the UK, USA, Canada, Singapore, China, and elsewhere. The document also provides ROTRONIC's warranty terms and conditions.
This document provides a product list and codes for WC flushing systems, urinal controls, automatic taps, showers, water management products, and accessories from DVS and Franke. It includes no-touch WC flushing kits that are stylish and deliver reliable performance, as well as urinal control systems that ensure clean washrooms while saving substantial water. The list provides over 100 product codes, descriptions, and individual part options across multiple washroom categories.
Cistermiser Water Efficient Washroom Controls - Specification Catalogue 2016Thorne & Derrick UK
The Hydraulic Valve is an automatic urinal flush control valve that uses a patented hydraulic mechanism to reduce water waste. It ensures the auto-flush cistern only fills and flushes when the washroom is in use. Over half a million have been installed and it provides reliable flushing without electricity or batteries. It also offers a hygiene flush option to prevent odors during periods of non-use.
Wolf - Hazardous Area Portable & Temporary Lighting - BrochureThorne & Derrick UK
The document discusses Wolf Safety's range of portable and temporary lighting and power distribution systems certified for use in potentially explosive atmospheres. The range includes portable lighting such as handheld torches, headtorches, and warning lamps powered by batteries, as well as temporary lighting fixtures and floodlights and temporary power distribution equipment. Wolf Safety manufactures hazardous area lighting certified for zones 0, 1, 2, 20, 21, and 22 to ensure safety wherever explosive gases, vapors, mists or dusts may be present.
VEGA – Level, Point Level & Pressure Measurement Sensors, Instruments & Trans...Thorne & Derrick UK
This document provides an overview of VEGA's plics modular instrumentation concept and level and pressure measurement products. The plics concept uses prefabricated components to assemble customized instruments for each customer's application requirements. Key VEGA level measurement products described include the VEGAPULS radar sensors for non-contact level measurement of liquids and solids, and the VEGAMIP microwave barriers for non-contact point level detection of liquids and solids. The document also outlines VEGA's global presence and commitment to developing innovative, easy to use measurement technology.
Thermon – Heat Tracing Cables (Self Regulating, Power Limiting, Constant Watt...Thorne & Derrick UK
Thermon provides complete heat tracing solutions for pipes, vessels, instrumentation, and other process equipment. They offer engineering, design, product selection, installation, training, commissioning, and maintenance services worldwide. Thermon has experience in industries like oil and gas, power generation, and chemical processing and can design customized systems to meet specific application needs.
SIKA is a family-owned German company with over 340 employees that has been developing and producing precision measurement and calibration equipment for over 100 years. They produce a wide range of industrial thermometers, pressure gauges, temperature and pressure sensors, flow meters, and calibration devices. SIKA ensures quality by calibrating products in their own accredited lab and providing expert support to customers worldwide through regional subsidiaries and partners.
SICK AG is a leading manufacturer of sensor technology products with over 5,800 employees worldwide. The document provides an overview of SICK's fluid sensor products, including level sensors, flow sensors, pressure sensors, and temperature sensors. It describes the company's wide product range and comprehensive services. Customers can find product information and order sensors through SICK's online portal.
The Patol analogue linear heat detection cable (LHDC) is designed to detect fires and overheating in areas that cannot support other detection methods. It can detect hot spots along its entire length and trigger alarms. The cable functions by monitoring the resistance of its dielectric insulation, which has a negative temperature coefficient, between the central conductor and outer braid layer. It is used with monitoring devices and can be installed in hazardous areas with intrinsically safe barriers. The cable comes in various outer sheath options for mechanical, chemical, or combined protection, and is suitable for a wide range of applications such as tunnels, conveyors, and industrial facilities.
Murco - Gas Detection (Refrigerant Gas Leak Detectors & Sensors) - Product Br...Thorne & Derrick UK
This document provides information on gas leak detection solutions, including fixed gas detectors, integrated area monitors, gas sensors, and aspirated refrigerant leak detectors. It lists several gas detection products with specifications such as power supply, alarm levels, outputs, housing options, and detectable gases. The detectors can be used to monitor refrigerants, toxins, and other gases in facilities like supermarkets, breweries, and industrial plants.
MSA Gas Detectors – Portable & Fixed Gas Detection - BrochureThorne & Derrick UK
- MSA is a leading manufacturer of safety equipment including supplied air respirators, air-purifying respirators, head, eye, and hearing protection, fall protection equipment, thermal imaging cameras, portable gas detection devices, and fixed gas and flame detection systems.
- They have manufacturing operations on five continents and serve customers in over 140 countries, ensuring customers have access to high-quality safety solutions wherever they are.
- MSA is committed to developing innovative products through testing and evaluation to protect workers' health and safety worldwide.
This document provides a product catalogue for Micronics Flow and Heat Meters. It summarizes their range of portable and permanent flow meters that use non-invasive ultrasonic clamp-on technology. They offer transit time and Doppler flow meters for measuring clean and aerated liquids respectively. Their portable models like the PF330 include data logging and output options. They also provide complementary products like software, heat meters, and permanent models like the U3000/U4000 for wall mounting. Case studies show how their meters help customers in industries monitor energy usage and efficiency.
LMK Thermosafe Hazardous Area Drum & IBC Product OverviewThorne & Derrick UK
LMK Thermosafe introduces new hazardous area certified induction drum and container heaters, as well as flexible heating jackets. This includes the THERMOSAFE induction drum heater, lifting frame, and top hat accessory. A new FARATHERM base heater provides heat to container bases. The INTELIHEAT jacket safely heats IBCs in hazardous areas. LMK also offers a range of stock and custom heating jackets.
Krohne Hazardous Area Process Instrumentation Meters Measurement - Product Ov...Thorne & Derrick UK
KROHNE provides a comprehensive range of flowmeters and flow controllers for measuring liquid and gas flows across various industries. Their product portfolio includes electromagnetic flowmeters, mass flowmeters, ultrasonic flowmeters, variable area flowmeters, differential pressure flowmeters, vortex flowmeters, and mechanical and electromagnetic flow controllers. KROHNE has over 90 years of experience in flow measurement and holds over 1,000 patents related to flow products. All of their flowmeters are wet-calibrated for accuracy.
Katronic is a manufacturer of ultrasonic clamp-on flowmeters for measuring flow in pipes. They offer a range of portable and fixed installation flowmeters for pipes from 10mm to 6500mm in diameter. Their flowmeters use ultrasonic transit time technology to measure flow velocity and rate. Katronic prides itself on high quality products and excellent customer service and support.
Itron is a global technology company that provides solutions to help utilities and cities manage energy and water resources more efficiently. Their solutions help utilities lower costs, modernize infrastructure, improve reliability and customer service. Itron offers a wide range of products and solutions for electricity, gas, water and smart cities to help address challenges of growing populations, climate change and resource scarcity. They have extensive experience deploying solutions in over 100 countries.
IFM Electronic - Sensors (Flow, Pressure, Level & Temperature Sensors) - Cata...Thorne & Derrick UK
This document provides an overview of ifm electronic gmbh, a manufacturer of industrial automation technology products. It describes ifm's wide range of over 7,800 sensors, systems, and connectivity solutions. The summary also outlines ifm's global presence with over 70 locations worldwide, commitment to quality and reliability with a 5-year warranty, and history of growth since being founded in 1969.
Freshworks Rethinks NoSQL for Rapid Scaling & Cost-EfficiencyScyllaDB
Freshworks creates AI-boosted business software that helps employees work more efficiently and effectively. Managing data across multiple RDBMS and NoSQL databases was already a challenge at their current scale. To prepare for 10X growth, they knew it was time to rethink their database strategy. Learn how they architected a solution that would simplify scaling while keeping costs under control.
Generating privacy-protected synthetic data using Secludy and MilvusZilliz
During this demo, the founders of Secludy will demonstrate how their system utilizes Milvus to store and manipulate embeddings for generating privacy-protected synthetic data. Their approach not only maintains the confidentiality of the original data but also enhances the utility and scalability of LLMs under privacy constraints. Attendees, including machine learning engineers, data scientists, and data managers, will witness first-hand how Secludy's integration with Milvus empowers organizations to harness the power of LLMs securely and efficiently.
Have you ever been confused by the myriad of choices offered by AWS for hosting a website or an API?
Lambda, Elastic Beanstalk, Lightsail, Amplify, S3 (and more!) can each host websites + APIs. But which one should we choose?
Which one is cheapest? Which one is fastest? Which one will scale to meet our needs?
Join me in this session as we dive into each AWS hosting service to determine which one is best for your scenario and explain why!
Trusted Execution Environment for Decentralized Process MiningLucaBarbaro3
Presentation of the paper "Trusted Execution Environment for Decentralized Process Mining" given during the CAiSE 2024 Conference in Cyprus on June 7, 2024.
Digital Banking in the Cloud: How Citizens Bank Unlocked Their MainframePrecisely
Inconsistent user experience and siloed data, high costs, and changing customer expectations – Citizens Bank was experiencing these challenges while it was attempting to deliver a superior digital banking experience for its clients. Its core banking applications run on the mainframe and Citizens was using legacy utilities to get the critical mainframe data to feed customer-facing channels, like call centers, web, and mobile. Ultimately, this led to higher operating costs (MIPS), delayed response times, and longer time to market.
Ever-changing customer expectations demand more modern digital experiences, and the bank needed to find a solution that could provide real-time data to its customer channels with low latency and operating costs. Join this session to learn how Citizens is leveraging Precisely to replicate mainframe data to its customer channels and deliver on their “modern digital bank” experiences.
Monitoring and Managing Anomaly Detection on OpenShift.pdfTosin Akinosho
Monitoring and Managing Anomaly Detection on OpenShift
Overview
Dive into the world of anomaly detection on edge devices with our comprehensive hands-on tutorial. This SlideShare presentation will guide you through the entire process, from data collection and model training to edge deployment and real-time monitoring. Perfect for those looking to implement robust anomaly detection systems on resource-constrained IoT/edge devices.
Key Topics Covered
1. Introduction to Anomaly Detection
- Understand the fundamentals of anomaly detection and its importance in identifying unusual behavior or failures in systems.
2. Understanding Edge (IoT)
- Learn about edge computing and IoT, and how they enable real-time data processing and decision-making at the source.
3. What is ArgoCD?
- Discover ArgoCD, a declarative, GitOps continuous delivery tool for Kubernetes, and its role in deploying applications on edge devices.
4. Deployment Using ArgoCD for Edge Devices
- Step-by-step guide on deploying anomaly detection models on edge devices using ArgoCD.
5. Introduction to Apache Kafka and S3
- Explore Apache Kafka for real-time data streaming and Amazon S3 for scalable storage solutions.
6. Viewing Kafka Messages in the Data Lake
- Learn how to view and analyze Kafka messages stored in a data lake for better insights.
7. What is Prometheus?
- Get to know Prometheus, an open-source monitoring and alerting toolkit, and its application in monitoring edge devices.
8. Monitoring Application Metrics with Prometheus
- Detailed instructions on setting up Prometheus to monitor the performance and health of your anomaly detection system.
9. What is Camel K?
- Introduction to Camel K, a lightweight integration framework built on Apache Camel, designed for Kubernetes.
10. Configuring Camel K Integrations for Data Pipelines
- Learn how to configure Camel K for seamless data pipeline integrations in your anomaly detection workflow.
11. What is a Jupyter Notebook?
- Overview of Jupyter Notebooks, an open-source web application for creating and sharing documents with live code, equations, visualizations, and narrative text.
12. Jupyter Notebooks with Code Examples
- Hands-on examples and code snippets in Jupyter Notebooks to help you implement and test anomaly detection models.
Programming Foundation Models with DSPy - Meetup SlidesZilliz
Prompting language models is hard, while programming language models is easy. In this talk, I will discuss the state-of-the-art framework DSPy for programming foundation models with its powerful optimizers and runtime constraint system.
5th LF Energy Power Grid Model Meet-up SlidesDanBrown980551
5th Power Grid Model Meet-up
It is with great pleasure that we extend to you an invitation to the 5th Power Grid Model Meet-up, scheduled for 6th June 2024. This event will adopt a hybrid format, allowing participants to join us either through an online Mircosoft Teams session or in person at TU/e located at Den Dolech 2, Eindhoven, Netherlands. The meet-up will be hosted by Eindhoven University of Technology (TU/e), a research university specializing in engineering science & technology.
Power Grid Model
The global energy transition is placing new and unprecedented demands on Distribution System Operators (DSOs). Alongside upgrades to grid capacity, processes such as digitization, capacity optimization, and congestion management are becoming vital for delivering reliable services.
Power Grid Model is an open source project from Linux Foundation Energy and provides a calculation engine that is increasingly essential for DSOs. It offers a standards-based foundation enabling real-time power systems analysis, simulations of electrical power grids, and sophisticated what-if analysis. In addition, it enables in-depth studies and analysis of the electrical power grid’s behavior and performance. This comprehensive model incorporates essential factors such as power generation capacity, electrical losses, voltage levels, power flows, and system stability.
Power Grid Model is currently being applied in a wide variety of use cases, including grid planning, expansion, reliability, and congestion studies. It can also help in analyzing the impact of renewable energy integration, assessing the effects of disturbances or faults, and developing strategies for grid control and optimization.
What to expect
For the upcoming meetup we are organizing, we have an exciting lineup of activities planned:
-Insightful presentations covering two practical applications of the Power Grid Model.
-An update on the latest advancements in Power Grid -Model technology during the first and second quarters of 2024.
-An interactive brainstorming session to discuss and propose new feature requests.
-An opportunity to connect with fellow Power Grid Model enthusiasts and users.
leewayhertz.com-AI in predictive maintenance Use cases technologies benefits ...alexjohnson7307
Predictive maintenance is a proactive approach that anticipates equipment failures before they happen. At the forefront of this innovative strategy is Artificial Intelligence (AI), which brings unprecedented precision and efficiency. AI in predictive maintenance is transforming industries by reducing downtime, minimizing costs, and enhancing productivity.
How to Interpret Trends in the Kalyan Rajdhani Mix Chart.pdfChart Kalyan
A Mix Chart displays historical data of numbers in a graphical or tabular form. The Kalyan Rajdhani Mix Chart specifically shows the results of a sequence of numbers over different periods.
Introduction of Cybersecurity with OSS at Code Europe 2024Hiroshi SHIBATA
I develop the Ruby programming language, RubyGems, and Bundler, which are package managers for Ruby. Today, I will introduce how to enhance the security of your application using open-source software (OSS) examples from Ruby and RubyGems.
The first topic is CVE (Common Vulnerabilities and Exposures). I have published CVEs many times. But what exactly is a CVE? I'll provide a basic understanding of CVEs and explain how to detect and handle vulnerabilities in OSS.
Next, let's discuss package managers. Package managers play a critical role in the OSS ecosystem. I'll explain how to manage library dependencies in your application.
I'll share insights into how the Ruby and RubyGems core team works to keep our ecosystem safe. By the end of this talk, you'll have a better understanding of how to safeguard your code.
Let's Integrate MuleSoft RPA, COMPOSER, APM with AWS IDP along with Slackshyamraj55
Discover the seamless integration of RPA (Robotic Process Automation), COMPOSER, and APM with AWS IDP enhanced with Slack notifications. Explore how these technologies converge to streamline workflows, optimize performance, and ensure secure access, all while leveraging the power of AWS IDP and real-time communication via Slack notifications.
Dandelion Hashtable: beyond billion requests per second on a commodity serverAntonios Katsarakis
This slide deck presents DLHT, a concurrent in-memory hashtable. Despite efforts to optimize hashtables, that go as far as sacrificing core functionality, state-of-the-art designs still incur multiple memory accesses per request and block request processing in three cases. First, most hashtables block while waiting for data to be retrieved from memory. Second, open-addressing designs, which represent the current state-of-the-art, either cannot free index slots on deletes or must block all requests to do so. Third, index resizes block every request until all objects are copied to the new index. Defying folklore wisdom, DLHT forgoes open-addressing and adopts a fully-featured and memory-aware closed-addressing design based on bounded cache-line-chaining. This design offers lock-free index operations and deletes that free slots instantly, (2) completes most requests with a single memory access, (3) utilizes software prefetching to hide memory latencies, and (4) employs a novel non-blocking and parallel resizing. In a commodity server and a memory-resident workload, DLHT surpasses 1.6B requests per second and provides 3.5x (12x) the throughput of the state-of-the-art closed-addressing (open-addressing) resizable hashtable on Gets (Deletes).
Driving Business Innovation: Latest Generative AI Advancements & Success StorySafe Software
Are you ready to revolutionize how you handle data? Join us for a webinar where we’ll bring you up to speed with the latest advancements in Generative AI technology and discover how leveraging FME with tools from giants like Google Gemini, Amazon, and Microsoft OpenAI can supercharge your workflow efficiency.
During the hour, we’ll take you through:
Guest Speaker Segment with Hannah Barrington: Dive into the world of dynamic real estate marketing with Hannah, the Marketing Manager at Workspace Group. Hear firsthand how their team generates engaging descriptions for thousands of office units by integrating diverse data sources—from PDF floorplans to web pages—using FME transformers, like OpenAIVisionConnector and AnthropicVisionConnector. This use case will show you how GenAI can streamline content creation for marketing across the board.
Ollama Use Case: Learn how Scenario Specialist Dmitri Bagh has utilized Ollama within FME to input data, create custom models, and enhance security protocols. This segment will include demos to illustrate the full capabilities of FME in AI-driven processes.
Custom AI Models: Discover how to leverage FME to build personalized AI models using your data. Whether it’s populating a model with local data for added security or integrating public AI tools, find out how FME facilitates a versatile and secure approach to AI.
We’ll wrap up with a live Q&A session where you can engage with our experts on your specific use cases, and learn more about optimizing your data workflows with AI.
This webinar is ideal for professionals seeking to harness the power of AI within their data management systems while ensuring high levels of customization and security. Whether you're a novice or an expert, gain actionable insights and strategies to elevate your data processes. Join us to see how FME and AI can revolutionize how you work with data!
2. 2
Power Industry | SICK
8015783/2013-05-08
Subject to change without notice
3. Table of contents
Challenges
Efficient, environmentally friendly and cost effective –
a difficult balance for electricity producers
4
Building security
Monitoring of perimeters / fences / walls
6
Applications in focus
Coal fired power plant
9
Gas fired power plant
23
Biomass fired power plant
31
Diesel fired power plant
45
Products
Product overview
55
General information
Company
72
Industries
74
SICK LifeTime Service
76
Product overview78
Industrial communication and unit integration / services
8015783/2013-05-08
Subject to change without notice
Power Industry | SICK
82
3
4. Challenges
A
B
C
D
E
F
H
I
J
K
L
M
N
O
P
Q
R
S
T
Challenges in the power industry
The power industry faces a number of challenges when
generating electricity. In every plant, the efficient use of fuel
and protection of assets are of utmost importance to insure
optimum profitability. Emission monitoring and pollution control
is a requirement in nearly every country.
SICK is an ideal partner for the power industry. With its broad
range of intelligent sensors and solutions they have proven
their applicability in all areas of the power generation process,
from material flow to pollution control to emissions monitoring
– all from a single source.
Emissions monitoring
Efficiency
Service
The regulatory requirements for emission
monitoring and reporting are becoming
more stringent in nearly every country in
the world. In order to insure compliance,
many customers turn to SICK to meet
their needs for dust, volumetric flow and
continuous gas emissions monitoring
solutions.
Combustion efficiency means getting the
maximum energy out of the fuel, without
damage or danger to plant staff and
equipment. SICK measures a number of
parameters which are used for combustion control: O2, CO and primary air
flow, all in-situ, to provide the quickest
possible signal for control.
Competent consulting, qualified planning
support, detailed project planning and
engineering, installation and start-up –
SICK provides all of these services with
our own personnel. SICK is also available
for service support of the equipment
during scheduled outages and in emergency situations.
4
Power Industry | SICK
8015783/2013-05-08
Subject to change without notice
5. Challenges
A
B
C
D
E
F
Pollution control systems
Optimum material flow
Corrosion protection
Scrubbers, catalytic reactors and
particulate filters all remove gaseous
pollutants from the flue gas to meet
stringent environmental limits. SICK‘s
range of in-situ gas analyzers provides
real-time measurement data to calculate
removal efficiency and control system
performance.
Monitoring fuel flow into the plant optimizes throughput, reduces loading time
and saves maintenance time. SICK has
a wide variety of scanners used to measure bulk volumes on conveyors as well
as level measurements in bins and silos.
Sensor data to help increase production
efficiency.
Boiler corrosion can be a nightmare for
plant owners. It means shortened boiler
lifetime, increased maintenance and
repair cost, unwanted outages: in short
– lower plant efficiency. SICK provides a
system to monitor CO and O2 directly at
the boiler wall to limit the potential for
corrosion.
8015783/2013-05-08
Subject to change without notice
Power Industry | SICK
5
H
I
J
K
L
M
N
O
P
Q
R
S
T
6. Building security
A
B
C
D
E
F
H
I
J
K
L
M
N
O
P
Q
R
S
T
Stop any security gaps before they appear
When it comes to protecting public buildings, industrial property or
construction projects, using security guards often have their limitations. Making additional use of electric or electronic protective
devices is therefore a sensible idea.
Reliable people counting systems are just one example of a device
that is essential in order to optimize business processes and
comply with safety regulations. Counting of persons can be used
for building management and automation or for marketing and
logistics purposes.
In addition to offering you an appropriate sensor solution, SICK can
also provide you with an expert consultation and the necessary
planning assistance.
Perimeter monitoring
Vertical or diagonal monitoring of fences. Electronic
laser sensors will detect danger before the mechanical protection devices are even tampered with.
Description and benefits
For building automation of a perimeter, fence or wall, we
distinguish two application areas area monitoring and location
indicator systems.
When this is done, the devices are set so that small animals,
adverse weather conditions or mere passers-by do not trigger
any false alarms.
With area monitoring, software in the sensor will manage all
monitoring areas. The system signals if intruders are present by
releasing the switching output and triggering an alarm whenever
an area is violated. This may, for instance, also be triggered by
objects or items regardless of whether they are mobile or not.
Another important feature is that the devices take privacy into
account. Unlike other protective devices, SICK sensors only
record contours for personal identification and not real images.
This means that the system will be able to tell that somebody is
present within the monitored area but not who it is.
The sensor uses the measuring data with which it has been
provided to determine the location.
6
Power Industry | SICK
8015783/2013-05-08
Subject to change without notice
7.
Building security
A
B
C
D
E
F
Perimeter protection/double fence
Unlike single fence, which uses vertical or diagonal area
monitoring, with a double fence horizontal monitoring
can also be used. The area between the fences then
provides constant, predefined conditions. SICK laser
scanners will monitor the area reliably and constantly
and have a low rate of false alarms.
Tasks and benefits
Recommended products
Laser scanners
Laser scanners
•• Make undetected intrusion into an area extremely difficult
•• Detect events at the perimeter of an area
•• Fence protection, protection of approach areas
•• Protection and/or monitoring of entrances
•• Excavation protection (with horizontal/diagonal setup)
•• Monitoring large areas
•• Store of all types of surrounding contours as references
•• Not impaired by surrounding lighting
•• Fixed-position obstacles can be blanked (e. g. walls)
8015783/2013-05-08
Subject to change without notice
LMS13x (LMS111), LMS2xx/
LMS5xx (outdoor), D-MRS,
L
LD-LRS
Power Industry | SICK
7
H
I
J
K
L
M
N
O
P
Q
R
S
T
8. Applications in focus
Coal fired power plant
5
3
4
2
1
8
Power Industry | SICK
8015783/2013-05-08
Subject to change without notice
9. Applications in focus
Coal fired power plant
6
Coal fired power plant
Focus 1
10
1 Coal handling
Focus 2
12
2 Combustion process
Focus 3
14
3 DeNOx
Focus 4
16
4 Dust removal
Focus 5
18
5 Wet flue gas desulfurization (FGD)
Focus 6
20
6 Continuous emission monitoring
8015783/2013-05-08
Subject to change without notice
Power Industry | SICK
9
10. Focus 1
Coal handling
Coal fired power plant
3
2
1
2 Protecting the coal mill by monitoring CO and O2
CO and O2 measurement in the coal mill
is important for early warning of a smoldering fire and/or a leak in the inerting
system. The MAC800 analyzer system
equipped with an explosion-protected
sampling probe is the ideal solution
for this monitoring. The system can be
configured to sequentially monitor a
number of mills. The SIDOR gas analyzer
provides simultaneous measurements of
O2 and CO.
An important feature is the stability of
the measuring benches allowing routine
adjustments to be made using only ambient air or inert gas. It is the ideal device
for safety-relevant measurements.
SIDOR g p. 59
MAC800 g p. 62
10
Power Industry | SICK
3 Overfill protection for coal bunkers/
silos
Coal is typically stored in silos after it has
been pulverized. In order to prevent overfilling of the silo, a point measurement of the
level is needed. The vibration limit switch
LBV300 is particularly outstanding for it’s
ruggedness. The LBV300 has no mechanically moving parts and is also resistant
to deposit formation, making it an ideal
choice for use in bin level monitoring of
coal.
LBV310 g p. 70
LBV330 g p. 70
8015783/2013-05-08
Subject to change without notice
11. Focus 1
Coal handling
Coal fired power plant
1 Conveyor control and crusher
monitoring
The coal is transported on conveyor
belts, moving from the coal pile to the
crushers or transfer points. Volume measurement is necessary here to control
coal delivery to the mill and optimize
throughput. Loading time can also be
reduced by making a volumetric measurement at this point. The Bulkscan®
LMS511 sensor records volume flow on
conveyors without contact, based on the
principle of laser flight time measurement. The integrated centre-of-gravity
calculator maximizes transport performance and detects one-sided loading
or uneven belt loads. The belt running
control serves to detect belt unevenness
which causes higher belt wear costs.
Bulkscan® LMS511 g p. 69
8015783/2013-05-08
Subject to change without notice
Power Industry | SICK
11
12. Focus 2
Combustion process
Coal fired power plant
4
3
2
1
2 Monitoring primary air flow
Power plant efficiency requires continuous monitoring and optimization of the
combustion process. The supply of combustion air is a primary task because it
delivers the required amount of oxygen
which must be optimized and controlled
carefully to ensure safe and efficient
combustion, to minimize fuel consumption as well as emission of pollutants like
CO, CO2 and NOx.
3 Montioring re-circulation air
Reliable and accurate monitoring of
primary combustion air volume flow at
the boiler inlet is very important. The
FLOWSIC100 ultrasonic flow meter is
ideal for measuring flow in this hot and
dusty ambient environment. The system
features accuracy even at low flow rates,
no loss of pressure and low cost of
installation due to short inlet and outlet
runs.
Power plant efficiency requires continuous monitoring and optimizing of the
combustion process. Monitoring the
recirculation air for CO is important
because it provides the necessary signal
needed to control the addition of fresh
air, to maintain the correct stoichiometric
ratio and optimize the effiiciency of the
combustion process. In-situ analysis
provides the fast response necessary for
control.
FLOWSIC100 M-AC g p. 67
12
Power Industry | SICK
8015783/2013-05-08
Subject to change without notice
13. Focus 2
Combustion process
Coal fired power plant
1 Monitoring at the boiler wall
The reducing atmosphere inside the
boiler is the primary cause of corrosion and the formation of deposits. By
maintaining CO at low levels and O2 at
minimum of 0.5%, corrosion or deterioration of the boiler wall can be minimized.
The GM960 boiler wall monitor is a
measuring system for the analysis of CO
and O2 at the inner boiler wall. The CO
Corrosion Level and CO Corrosion Load
are determined at each of up to 40 measuring points. CO and O2 values and CO
Corrosion Levels detect potential danger
of corrosion so that immediate action
can be taken such as better control of
feeders or combustion air. CO Corrosion
Load represents the long term CO corrosion exposure to the boiler wall.
GM960 g p. 63
4 Gas monitoring at the boiler outlet
The GM901 in-situ CO gas analyzer
is available as a cross-duct type. As a
result, it is suited to a broad range of
applications - even for difficult measuring
tasks such as overpressure, critical flow
profiles or high gas concentrations.
GM901 g p. 58
8015783/2013-05-08
Subject to change without notice
Combustion efficiency is an important
control parameter when fuel is burned to
generate heat. Zirconium oxide oxygen
analyzers are the most widely used combustion control instruments. CO is measured at the economizer as a secondary
component for burner control. Reliable
and accurate monitoring of O2 and CO
at the boiler outlet are key elements to
control the excess air in the combustion
process.
The ZIRKOR302 in-situ analyzer provides
a reliable and rapid measurement of
oxygen even at higher temperatures.
The GM35 gas analyzer measures CO,
CO2 and H2O concentrations as well as
temperature and pressure quickly, easily
and economically.
GM35 g p. 57
ZIRKOR302 g p. 58
Power Industry | SICK
13
14. Focus 3
DeNOx
Coal fired power plant
1
3
2
2 Volume flow measurement
To determine mass emissions, flow in
the duct after the SCR can be measured. The “High Power” FLOWSIC100 H
ultrasonic meter is suitable for measurements in large diameter ducts as
well as for applications with high dust
content. Rugged titanium transducers
are standard. For very hot gas temperatures 260°C ...450°C the measuring
system operates with built-in cooling air
to protect the sensor heads against high
temperature.
The MCU controller is used for input
and output of signals, for calculation
of volume flow to reference conditions
(standardization) as well as for user
interface.
FLOWSIC100 H g p. 66
14
Power Industry | SICK
8015783/2013-05-08
Subject to change without notice
15. Focus 3
DeNOx
Coal fired power plant
1 Economizer outlet, selective
catalytic reactor (SCR) inlet
The gas conditions include high dust
and high temperature, so analyzer/
probe installation location is important.
Abrasion and clogging can occur due to
particulate load and temperature in both
process and ambient environments. The
GM32 in-situ gas analyzer measures NO
and NO2 if required, as well as pressure and temperature in the gas duct
- directly, fast and without gas sampling
and transport - true values in “real time”.
The ZIRKOR302 in-situ analyzer, provides
a reliable and rapid measurement of
oxygen for reporting normalized values.
GM32 g p. 56
ZIRKOR302 g p. 58
3 Selective catalytic reactor (SCR) outlet prior to air heater
NOx is typically measured at the outlet
of the SCR for removal efficiency calculation or feedback to NH3 injection
controller. Ammonia is often measured
here to insure that NH3 slip is low for
several reasons including clogging of the
air heater and NH3 bonding to the fly ash
making disposal a problem. The GM32
in-situ gas analyzer measures NO and
NO2 (NOx) in the gas duct - directly, fast
and without gas sampling and transport.
Reliability, precision and fast response
times are the distinguishing features
of the GM700 laser gas analyzer which
continuously monitors low levels of NH3.
GM32 g p. 56 GM700 g p. 57 ZIRKOR302 g p. 58
8015783/2013-05-08
Subject to change without notice
Power Industry | SICK
15
16. Focus 4
Dust removal
Coal fired power plant
4
1
2
2 Ash collection hoppers
3 Monitoring dust removal efficiency
The particulate that passes into the electrostatic precipitator is collected on the
plate surfaces. Once “rapping” is done,
the collected particulate falls off into collecting hoppers. In order to detect if the
hopper is full, point level measurements
are made.The vibration limit switch
LBV300 is particularly outstanding for
its ruggedness. The LBV300 has no
mechanically moving parts and is insensitive to deposit formation. Apart from
that, it is characterized by easy installation as well as start-up without filling.
Flue gases from coal fired combustion
processes are loaded with particulate
matter (PM) and, due to environmental
regulations, must be cleaned before
release into the atmosphere. This is
done by passing a dedusting device,
such as an electrostatic precipitator. The
correct operation of the electrostatic
precipitator is ensured by continuously
monitoring the dust concentration after
the filter.
LBV310 g p. 70
16
Power Industry | SICK
The DUSTHUNTER SP100 is a good
choice for very low to medium dust concentrations. The measurement is based
on the forward scattering of light. An
automatic check of zero and reference
point as well as contamination check are
integrated in the device.
DUSTHUNTER SP100 g p. 64
8015783/2013-05-08
Subject to change without notice
17. Focus 4
Dust removal
Coal fired power plant
1 Electrostatic precipitator
protection
3
Flue gases from coal-fired combustion
are loaded with particulate matter. The
particulate has to be removed before the
gas is released to the atmosphere. In
order to do that, coal fired plants often
use electrostatic precipitators to remove
dust. CO is monitored in the ductwork
at the inlet of the precipitator in order to
provide an indication if a high level of CO
is present. This could cause an explosion
inside the precipitator which is dangerous and costly. The GM901 gas analyzer
is available as a cross-duct type. As a
result, it is suitable even for difficult
measuring tasks such as high pressure,
critical flow profiles or high measuring
gas concentrations.
GM901 g p. 58
4 Filling fly ash tanks for transport to disposal site
Fly ash is removed from the collection
hoppers and then transported by trucks
to disposal sites. Position sensors are
used to insure that the loading spouts
are correctly positioned and no fly ash
escapes into the atmosphere during
loading. The LMS511 is used to position
the trucks underneath the collection
hoppers. This powerful and efficient
laser scanner can measure to ranges of
up to 80 m.
Housed in a rugged IP 67 enclosure, it is
immune to harsh weather conditions and
high dust environments associated with
ash loading.
Bulkscan® LMS511 g p. 69
8015783/2013-05-08
Subject to change without notice
Power Industry | SICK
17
18. Focus 5
Wet flue gas desulfurization (FGD)
Coal fired power plant
2
4
1
2 Outlet DeSOx acid gas control
Measuring acid gases such as SO3 and
H2SO4 after the desulfurization system
can provide feedback control for dry
sorbent injection. Sorbents are used
to reduce acid gases as well as for the
removal of elemental mercury. These
acid gases also cause corrosion in the
duct work and their presence is indicated
by a blue plume. The MCS100E HW
extractive analyzer measures SO2, SO3,
H2SO4 as well as HCl, H2O and a variety
of other gases.
MCS100E HW g p. 60
18
Power Industry | SICK
3 Overfill protection of the lime silo
A built-in calibration filter gives the operator the ability to run internal checks of
the system to maintain stability without
the need for expensive and dangerous
test gases or liquids. The high sample
gas flow rate of the system ensures quick
response so control can be performed
based on the analysis results.
Lime is typically stored in silos for use
as an absorber/neutralizer in the flue
gas desulfurization system. In order to
prevent overfilling of the silo, a point
measurement of the level is necessary.
The vibration limit switch LBV300 is particularly outstanding for it’s ruggedness.
The LBV300 has no mechanically moving
parts and is also resistant to deposit
formation, making it an ideal choice for
monitoring bin levels.
LBV310 g p. 70
8015783/2013-05-08
Subject to change without notice
19. Coal fired power plant
Focus 5
Wet flue gas desulfurization (FGD)
1 Flue gas desulfurization (FGD)
inlet control
3
SO2 is measured at the inlet to the flue
gas desulfurization system to control
the lime dosification and in addition to
make the removal efficiency calculation to check FGD performance. O2 is
measured for normalization. The GM32
in-situ gas analyzer is recommended for
the measurement of SO2 because it is
fast and measures under the process
conditions without gas sampling and
transport. The automatic check cycle
using internal components as zero-point
reflector, gas filled cuvette and grid filters
provide periodic checks of zero and span
ensuring high availability without using
expensive test gases. The ZIRKOR302
in-situ analyzer provides a reliable and
rapid measurement of oxygen, even at
higher temperatures.
GM32 g p. 56
ZIRKOR302 g p. 58
4 Filling gypsum tanks for transport
to customer.
Gypsum by-product is created by forced
oxidation of the CaSO3 solution created
during the desulfurization process.
CaSO4 also known as gypsum is sold to
the building industry (e.g. for the production production of dry wall). Sensors are
used to assist with product fill in the
gypsum tankers. The LMS511 is used
to position the loading spouts correctly
for filling the gypsum into the tanker or
truck.
Bulkscan® LMS511 g p. 69
8015783/2013-05-08
Subject to change without notice
Power Industry | SICK
19
20. Focus 6
Continuous emission monitoring
Coal fired power plant
5
3
2
2 Monitoring dust emissions
1
3
4 Emission monitoring in exhaust gas
20
Power Industry | SICK
The scattered light principle allows even
very low dust concentrations to be measured. The FWE200 features an automatic zero and span check and internal
contamination check system resulting in
minimum maintenance requirements.
Environmental regulations require the
continuous monitoring of certain pollutants and reference values. These
regulations for emission monitoring
are specific for each country. In many
countries, emission measuring technology must be tested for suitability e. g. in
Europe in accordance with EN15267-3,
or in the US in compliance with EPA standards. SICK’s wide product portfolio for
emission monitoring provides complete
solutions all from one source.
FWE200 g p. 63
The FWE200 dust measuring system is
designed to measure dust concentration
in wet gas. Measurement can be difficult
downstream of a wet flue gas desulfurization system (FGD), because the water
vapor interferes with the dust measurement. Using the FWE200 the gas
is extracted via a sampling probe and
heated above dew point. Any droplets in
the gas are vaporized to ensure accurate
measurement results.
MERCEM300Z g p. 60
8015783/2013-05-08
Subject to change without notice
21. Focus 6
Continuous emission monitoring
Coal fired power plant
1 Stack gas flow monitoring
Stack gas flow meters can be used to
determine the mass emissions from
combustion sources. The “High Power”
FLOWSIC100 H ultrasonic flow meter
is suitable for measurements in stacks
with large diameters as well as for
applications with high dust content. The
FLOWSIC100 M version is used for stack
diameters up to 3 1/2 meters. Rugged
titanium transducers are standard and
suitable under difficult conditions. The
measuring system needs no purge air
and consists of 2 sender/receiver units
and an MCU control unit. The MCU is
used for input and output of signals, for
calculation of volume flow to reference
conditions as well as user-friendly operator interface.
4
FLOWSIC100 H g p. 66
5 Greenhouse gas control
A specially developed CEMS package,
the PowerCEMS100, measures CO, NOx,
SO2 and O2. The MERCEM300Z mercury
measuring system monitors Hg emissions in flue gases with high availability
even at very low concentration ranges
and meets required legislative regulations. Data aquisition systems from SICK
complete the CEMS package.
PowerCEMS g p. 61
8015783/2013-05-08
Subject to change without notice
The European directive 2003/87/EC
for trading greenhouse gas emission
allowances requires proof of the CO2
emissions in many plants. Usually the
CO2 amount is rather difficult to calculate, therefore measurement in the
exhaust duct is a desireable alternative
provided the total uncertainty limits are
met. SICK has a package for monitoring
the CO2 emissions directly and providing the uncertainty certifications for
reporting and trading of allowances on
the basis of the EU regulations. GHG
Control uses the GM35 NDIR cross duct
monitoring system and the FLOWSIC100
ultrasonic flow meter as the basis for the
measurement. Laborious sampling and
fuel analysis necessary for the calculation method can be either reduced or
eliminated entirely.
GM35 g p. 57
FLOWSIC100 g p. 66
Power Industry | SICK
21
22. Applications in focus
Gas fired power plant
2
1
22
Power Industry | SICK
8015783/2013-05-08
Subject to change without notice
23. Applications in focus
Gas fired power plant
3
Gas fired power plant
Focus 1
24
1 Gas supply
Focus 2
26
2 DeNOx
Focus 3
28
3 Continuous emission monitoring
8015783/2013-05-08
Subject to change without notice
Power Industry | SICK
23
24. Focus 1
Gas supply
Gas fired power plant
2
1
2 Gas flow
Measuring the consumption of natural
gas at the turbine inlet provides the
necessary information for the computation of total mass emissions of the plant.
Here accuracy of measurement and
system reliability is of utmost importance. The new FLOWSIC500 ultrasonic
compact gas meter from SICK enables
highly accurate metering in natural gas
distribution.
No moving parts means the
FLOWSIC500 is a robust, fail-safe and
low-maintenance device resulting in a
significant reduction in operating costs.
FLOWSIC500 can easily be integrated
into existing measuring stations. The
FLOWSIC500 operates either in an
energy self-sufficient configuration or
failsafe in network operation with battery
back-up.
FLOWSIC500 g p. 67
24
Power Industry | SICK
8015783/2013-05-08
Subject to change without notice
25. Focus 1
Gas supply
Gas fired power plant
1 Gas custody transfer
Whether for custody transfer metering or
internal company metering and billing,
monitoring the flow of natural gas into
the power plant is very important. The
FLOWSIC600 is an ultrasonic gas flow
meter for high precision measurement.
The FLOWSIC600 2plex combines a
fiscal gas meter (4 measuring paths) and
a check flow meter (1 measuring path) in
one meter body. This provides advanced
diagnostic capabilities. The compact
design with concealed cabling provides
a robust, trouble-free and low-maintenance system. Due to the direct path
layout, the meter is not influenced by
contamination. This results in long-term
stability and accuracy of the system.
Adjustable impulse outputs or Modbus
connections allow the use of installed
flow computers.
8015783/2013-05-08
Subject to change without notice
FLOWSIC600 g p. 68
Power Industry | SICK
25
26. Focus 2
DeNOx
Gas fired power plant
1
26
Power Industry | SICK
8015783/2013-05-08
Subject to change without notice
27. Focus 2
DeNOx
Gas fired power plant
1 DeNOx heat recovery steam
generation (HRSG) outlet
In some countries or states, the limits for
NOx emissions are so low that even low
NOx fuels such as gas require additional
pollution control devices in order to meet
the stringent emission limits. In such
cases selective catalytic reduction systems are installed to further reduce the
NOx emissions and meet permit requirements. TheGM32 in-situ gas analyzer
measures low levels of NOx - directly, fast
and without gas sampling and transport.
Using the cross duct version, the entire
HRSG duct can be used as the active
measuring path enabling measurement
of very low concentrations of pollutants.
The GM700 laser analyzer measures
NH3 slip with high precision and speed.
The ZIRKOR302 in-situ O2 analyzer provides a reliable and rapid measurement
of even at higher temperatures.
GM32 g p. 56
ZIRKOR302 g p. 58
GM700 g p. 57
8015783/2013-05-08
Subject to change without notice
Power Industry | SICK
27
28. Focus 3
Continuous emission monitoring
Gas fired power plant
1
3
2
2 Monitoring dust emissions
Dust concentration or opacity is typically
measured in the stack emission in a
fossil fuel fired power plant. The exact
ranges of measurement and the number
of components are dependent on local or
national regulatory requirements and are
indicated in the plant operating permit.
The DUSTHUNTER SP100 is a probe
version for very low to medium dust concentrations. The measurement is based
on the forward scattering of light.
3 Emission monitoring in exhaust gas
An automatic check of zero and reference point as well as contamination
check are included. The DUSTHUNTER
T100 is a cross duct version measuring dust at medium to high concentrations. The principle of operation is
optical transmittance. When the correct
purge air blowers are used, the T100
is suitable for measurements at high
temperatures.
Legal environment regulations require
the continuous monitoring of certain
pollutants and reference values. These
regulations for emission monitoring
are specific for each country. In many
countries, emission measuring technology must be tested for suitability e. g. in
Europe in accordance with EN15267-3,
or in the US in compliance with EPA standards. SICK’s wide product portfolio for
emission monitoring provides complete
solutions from one source.
DUSTHUNTER T100 g p. 65
28
Power Industry | SICK
8015783/2013-05-08
Subject to change without notice
29. Focus 3
Continuous emission monitoring
Gas fired power plant
1 Stack gas flow monitoring
Stack gas flow meters are often used
to determine the mass emissions from
combustion sources. The FLOWSIC100
M-AC ultrasonic flow monitor is especially
suited for stacks with medium diameter
and offers superior accuracy of measurement to meet rigorous environmental
standards. The FLOWSIC100 M-AC
includes internal air cooling of the sensor
heads in order to allow the accurate
ultrasonic systems to be used in high
temperatures up to 450°C. The system
consists of 2 sender/receiver units and
an MCU control unit. The MCU offers
input and output of signals, calculation
of volume flow to reference conditions
via a user-friendly operator interface.
4
FLOWSIC100 M-AC g p. 67
4 Greenhouse gas control
A specially developed CEMS package
the PowerCEMS100 measures CO, NOx,
O2 and optionally SO2. Data aquisition
system from SICK complete the CEMS
package.
PowerCEMS g p. 61
8015783/2013-05-08
Subject to change without notice
The European directive 2003/87/EC
for trading greenhouse gas emission
allowances requires the proof of the CO2
emissions in many plants. Usually the
exact amount of CO2 is rather difficult
to calculate, therefore measurement in
the exhaust duct is a desirable alternative provided the total uncertainty
limits are met. SICK has developed a
solution for monitoring the CO2 emissions directly and providing the uncertainty certifications for reporting and
trading of allowances on the basis of
the EU regulations. GHG Control solution
includes the GM35 NDIR gas analyzer,
the FLOWSIC100 ultrasonic flow meter,
MEAC GHG software package plus engineering services to provide a complete
measurement system eliminating the
need for laborious calculation methods
to save time and money.
GM35 g p. 57
FLOWSIC100 g p. 66
Power Industry | SICK
29
30. Applications in focus
Biomass fired power plant
4
3
2
1
30
Power Industry | SICK
8015783/2013-05-08
Subject to change without notice
31. Applications in focus
Biomass fired power plant
5
Biomass fired power plant
Focus 1
32
1 Fuel delivery / Storage
Focus 2
36
2 Combustion process
Focus 3
38
3 Dry flue gas desulfurization (FGD)
Focus 4
40
4 Dust removal
Focus 5
42
5 Continuous emission monitoring
8015783/2013-05-08
Subject to change without notice
Power Industry | SICK
31
32. Focus 1
Fuel delivery / Storage
Biomass fired power plant
2
1
2 Natural gas flow
Measuring the flow of natural gas to
feed the burners is done to control
consumption, maintain fuel supply and
system reliability. The new FLOWSIC500
ultrasonic compact gas meter provides
accurate metering in natural gas distribution. Operating costs are reduced by no
moving parts, fail safe operation and
low maintenance. The FLOWSIC500 can
easily be integrated into existing measuring stations.
It’s available in either an energy selfsufficient or fail safe configuration with
battery back-up.
FLOWSIC500 g p. 67
32
Power Industry | SICK
8015783/2013-05-08
Subject to change without notice
33. Focus 1
Fuel delivery / Storage
Biomass fired power plant
1 Biogas flow
Measuring the flow of biogas used to
feed the burners is often done to control
consumption and maintain fuel supply.
Biogas is used as an alternative to
biomass depending on the availability
and price of the different fuel types. The
FLOWSIC600 Bio is a two path ultrasonic
gas flow meter specifically designed for
accurate measurement of biogas. The
low-maintenance meter is housed in a
corrosion-resistant body, with no moving
parts, no pressure drop and concealed
cabling. Sealed ultrasonic transducers
make the FLOWSIC600 Bio suitable for
use in dry, wet or corrosive gases.
8015783/2013-05-08
Subject to change without notice
FLOWSIC600 Bio g p. 68
Power Industry | SICK
33
34. Focus 1
Fuel delivery / Storage
Biomass fired power plant
3
1
2
2 Overfill protection for biomass
bunkers/silos
Biomass is typically stored in silos before
being used in the burners as a primary
fuel source. In order to prevent overfilling
of the silo, a level point measurement is
recommended. The vibration limit switch
LBV300 is particularly outstanding for
it’s ruggedness. The LBV300 has no
mechanically moving parts and is also
resistant to deposit formation, making it
an ideal choice for use in bin level monitoring of biomass.
LBV310 g p. 70
34
Power Industry | SICK
4 Conveyor control and shredder monitoring
Biomass is transported on conveyor
belts, moving from the heap to the shredders or transfer points. Volume measurement is necessary to control fuel
delivery to the shredder and optimize
throughput. Loading time can also be
reduced by making volumetric measurements at these points. The laser flow
sensor LMS511 records volume flow on
conveyors without contact.
This is based on the principle of laser
time of flight measurement. The Bulkscan® LMS511 stands out particularly
through sturdy design, reliability as well
as wear-free operation. The integrated
centre-of-gravity calculator maximizes
transport performance and detects
one-sided loading or uneven belt loads
saving on wear and tear of the belts and
maintenance cost.
Bulkscan® LMS511 g p. 69
8015783/2013-05-08
Subject to change without notice
35. Focus 1
Fuel delivery / Storage
Biomass fired power plant
1
4
3 Protection of the biomass
bunker and the wood shredder
Measuring CO and O2 in the biomass
bunker and in the shredder is an important measure to provide early warning
of a smoldering fire and/or a leak in the
inerting system. The MAC800 analyzer
system equipped with an explosionprotected sampling probe is the ideal
solution for this monitoring point. The
system can be configured to sequentially monitor a number of bunkers and
or shredders. The gas analyzer SIDOR
provides simultaneous measurements
of O2 and CO. An important feature is
the stability of the measuring system
allowing routine adjustments to be made
using only ambient air or inert gas. It
is the ideal device for safety-relevant
measurements.
SIDOR g p. 59
MAC800 g p. 62
8015783/2013-05-08
Subject to change without notice
Power Industry | SICK
35
36. Focus 2
Combustion process
Biomass fired power plant
4
1
3
2
2 Monitoring primary air flow
Power plant efficiency requires continuous monitoring and optimizing of the
combustion process. Combustion air
supply delivers oxygen which must be
optimized and controlled for safe and
efficient combustion to minimize fuel
consumption and emission of CO, CO2
and NOx pollutants. Reliable and accurate monitoring of primary combustion
air volume flow at the boiler inlet is very
important.
3 Montioring re-circulation air
The FLOWSIC100 ultrasonic flow meter
is ideal for measuring flow in this hot and
dusty ambient environment. The meter
features a high measuring dynamic,
accuracy even at low flow rates, no pressure loss and low installation cost due to
short inlet and outlet runs.
Power plant efficiency requires continuous monitoring and optimizing of
the combustion process. Monitoring
recirculation air for CO is important to
control the addition of fresh air, maintain the correct stoichiometric ratio and
optimize the efficiency of the combustion
process. In-situ analysis provides the fast
response necessary for control.
FLOWSIC100 M-AC g p. 67
36
Power Industry | SICK
8015783/2013-05-08
Subject to change without notice
37. Focus 2
Combustion process
Biomass fired power plant
1 Monitoring at the boiler wall
Reducing atmosphere inside of the
boiler is the primary cause of corrosion
and formation of deposits. Corrosion or
deterioration of the boiler wall can be
avoided by maintaining CO at low levels
and O2 at minimum of 0.5%. The GM960
boiler wall monitor is a trend measuring
system for the analysis of CO and O2 at
the inner boiler wall. The CO Corrosion
Level and CO Corrosion Load are determined at each of up to 40 measuring
points. The CO and O2 values and the CO
Corrosion Levels are aimed at detecting
potential danger of corrosion so that
immediate action can be taken such as
better control of feeders or combustion
air. The value of the CO Corrosion Load
represents the long term CO corrosion
exposure to the boiler wall.
GM960 g p. 63
4 Gas monitoring at the boiler outlet
The GM901 in-situ CO gas analyzer is
available as a cross-duct or probe type
suitable to a broad range of applications such as high dust loads, overpressure, critical flow profiles or high gas
concentrations.
GM901 g p. 58
8015783/2013-05-08
Subject to change without notice
Whenever fuel is burned to generate
heat, combustion efficiency is important
to control. Zirconium oxide oxygen analyzers are widely used for combustion
control, CO is measured as a secondary
component. Reliable and accurate monitoring of O2 and CO at the boiler outlet
is necessary to control excess air in the
combustion process. The ZIRKOR302 insitu analyzer provides reliable and rapid
measurement of oxygen even at higher
temperatures.
The GM35 gas analyzer quickly, easily
and economically measures CO, CO2,
humidity concentrations, temperature
and pressure. HCl measurement using
the TDLS (tunable diode laser spectroscopy) system GM700 can be used as
part of acid gas sorbent injection control.
GM35 g p. 57
GM700 g p. 57
ZIRKOR302 g p. 58
Power Industry | SICK
37
38. Focus 3
Dry flue gas desulfurization (FGD)
Biomass fired power plant
1
2
3
2 Flue gas desulfurization (FGD) outlet monitoring
New tighter limits on gas emissions
require plants to install absorbers to
remove acid gases such as SO2 and HCl.
Water is injected upstream of the flue
gas desulfurization unit and termperature is lowered to aid in efficient SO2
removal. It is critical to monitor the H2O
injection because an overdose would
transform the dry sorbent into a sticky
mass leading to malfunction of the
bag filters. HCl is measured as part of
the acid gas sorbent injection control.
The MCS300HW system is designed to
measure up to 6 components in the hot
wet gas phase including O2. The built-in
automatic adjustment filter allows for
routine calibration eliminating the need
for expensive test gases.
MCS300P HW g p. 59
38
Power Industry | SICK
8015783/2013-05-08
Subject to change without notice
39. Biomass fired power plant
Focus 3
Dry flue gas desulfurization (FGD)
1 Flue gas desulfurization (FGD) inlet
monitoring
SO2 is measured at the flue gas desulfurization system inlet to make the removal
efficiency calculation and can be useful
as feed forward signal for lime dosification. O2 is measured for normalization.
The GM32 in-situ gas analyzer for SO2
measures under the process conditions
without gas sampling and transport
with reliable measurement results. In
case of a malfunction an early warning
will be shown. The ZIRKOR302 in-situ
analyzer provides a reliable and rapid
measurement of oxygen, also at higher
temperatures.
GM32 g p. 56
3 Overfill protection of the lime silo
Lime is typically stored in silos for use
as a absorber/neutralizer in the flue gas
desulfurization system. In order to prevent overfilling of the silo, a point measurement of the level is recommended.
The vibration limit switch LBV300 is particularly outstanding for it’s ruggedness.
The LBV300 has no mechanically moving
parts and is also insensitive to deposit
formation, making it an ideal choice for
monitoring bin levels.
LBV310 g p. 70
8015783/2013-05-08
Subject to change without notice
Power Industry | SICK
39
40. Focus 4
Dust removal
Biomass fired power plant
3
4
2
1
2 Ash collection hoppers
3 Dust removal efficiency
The particulate that passes into the
baghouse is collected on the filter bag
surfaces. When the fly ash is shaken off
it falls into collecting hoppers. In order
to detect if the hopper is full, point level
measurements are made.The vibration
limit switch LBV300 is particularly outstanding for its ruggedness. The LBV300
has no mechanically moving parts and
is also insensitive to deposit formation.
Apart from that, it is characterized by
easy installation as well as start-up
without filling.
Flue gas from biomass combustion contains a high level of particulate matter
(PM) environmental regulations stipulate
this must be removed before releasing
the gas into the atmosphere. New tighter
limits on dust emissions require plants to
install bag houses with fabric filters. Bag
house filters collect the particulate by
passing through a tightly woven fabric.
LBV310 g p. 70
40
Power Industry | SICK
The DUSTHUNTER SB50 measures low
dust concentrations based on the back
scattering of light. An automatic zero
check and reference point is integrated
reducing maintenance. One-sided installation makes it easy to install in the
ductwork downstream of the bag filter.
DUSTHUNTER SB50 g p. 64
8015783/2013-05-08
Subject to change without notice
41. Focus 4
Dust removal
Biomass fired power plant
1 Filter protection
Flue gases from biomass combustion
include a significant amount of dust
which has to be removed before the
gas is released into the atmosphere. In
order to remove dust, biomass plants
often used bag filters. CO is monitored
in the ash sieve to indicate if a high level
is present. CO could cause a dangerous and costly explosion inside the filter
system. The GM901 CO gas analyzer is
available as a cross-duct or probe type
and is suitable for difficult measuring
tasks such as high dust loads, overpressure, critical flow profiles or high measuring gas concentrations.
GM901 g p. 58
4 Filling fly ash tanks for transport to disposal site.
Fly ash is removed from the collection
hoppers and then transported by trucks
to disposal sites. Sensors are used to
insure that the loading spouts are correctly positioned and no fly ash escapes
into the atmosphere at this transfer
point. The LMS511 is used to position
the trucks underneath the collection
hoppers.
This powerful and efficient laser scanner can measure up to ranges of 80 m.
Housed in a rugged IP 67 enclosure, it
is resistant to harsh weather conditions
and high dust environments associated
with ash loading.
Bulkscan® LMS511 g p. 69
8015783/2013-05-08
Subject to change without notice
Power Industry | SICK
41
42. Focus 5
Continuous emission monitoring
Biomass fired power plant
4
3
1
2
2 Monitoring dust emissions
Dust concentration or opacity is measured in the stack emissions of a biomass co-fired plant. The exact ranges of
measurement and the number of components are dependent on local or national
regulations indicated in the plant operating permit. The DUSTHUNTER SP100
is an approved measuring device with
probe for very low to medium dust
concentrations based on the forward
scattering of light.
3 Emission monitoring in exhaust gas
Automatic zero check, contamination
check and reference point is included.
The DUSTHUNTER T200 is a measuring device for dust at medium to high
concentrations based on the optical
transmittance principal. It includes a
two-sided contamination check and
automatic self-alignment of the optical
assembly.
Local environment regulations require
the continuous monitoring of certain
pollutants and reference values specific
to each country. In many countries,
emission measuring technology must be
tested for suitability, in Europe in accordance with EN15267-3 or in the US in
compliance with EPA standards. SICK’s
wide product portfolio for emission monitoring provides complete solutions from
one source.
DUSTHUNTER SP100 g p. 64
42
Power Industry | SICK
8015783/2013-05-08
Subject to change without notice
43. Focus 5
Continuous emission monitoring
Biomass fired power plant
1 Stack gas flow monitoring
Stack gas flow meters can be used to determine the mass emissions from combustion
sources. The FLOWSIC100 M is especially
suited for stacks with medium diameter.
Rugged titanium transducers are standard
and suitable under difficult conditions.
The measuring system needs no purge air,
consists of 2 sender/receiver units and an
MCU control unit. The MCU is used for input
and output of signals, for calculation of
volume flow to reference conditions as well
as user-friendly operator interface.
FLOWSIC100 M g p. 66
4 Greenhouse gas control
A specially developed CEMS package the
PowerCEMS100 measures CO, NOx, SO2,
and O2 . Data aquisition systems from
SICK complete the CEMS package.
PowerCEMS g p. 61
8015783/2013-05-08
Subject to change without notice
European directive 2003/87/EC for trading greenhouse gas emission allowances
requires proof of the emitted amount of
carbon dioxide in many plants. Calculating CO2 can be rather difficult, therefore
measurement in the exhaust duct is a
desireable alternative as long as the
total uncertainty limits are met. SICK has
developed a unique system for monitoring the CO2 emissions directly and
providing the uncertainty certifications
for reporting and trading of allowances
on the basis of the EU regulations. GHG
Control uses the GM35 NDIR cross duct
monitoring system and the FLOWSIC100
ultrasonic flow meter for the measurement; reducing or entirely eliminating
laborious sampling and fuel analysis
necessary for the calculation method.
GM35 g p. 57
FLOWSIC100 g p. 66
Power Industry | SICK
43
44. Applications in focus
Diesel fired power plant
2
1
44
Power Industry | SICK
8015783/2013-05-08
Subject to change without notice
45. Applications in focus
Diesel fired power plant
4
3
Diesel fired power plant
Focus 1
46
1 Fuel delivery / Storage
Focus 2
48
2 DeNOx
Focus 3
50
3 Dry flue gas desulfurization (FGD)
Focus 4
52
4 Continuous emission monitoring
8015783/2013-05-08
Subject to change without notice
Power Industry | SICK
45
46. Focus 1
Fuel delivery / Storage
Diesel fired power plant
2
4
1
2 Measurement of raw biogas under low pressure before and after purification
Measuring the flow of biogas feed to the
engines is often done in order to control
consumption and to insure the fuel
supply is not exhausted. Biogas is used
as an alternative to natural gas depending on the availability and price of the different fuel types. The FLOWSIC600 Bio
is an ultrasonic gas flow meter made for
demanding environments.
The FLOWSIC600 Bio 2-path is the
basic model with two measuring paths
in one meter body. The meter features
no pressure drop and no moving parts.
The ultrasonic transducers and the
lightweight meter body made from
polyethylene (PE100) are suitable for
H2S concentration in the wet biogas
with the potential for corrosion. The
FLOWSIC600 Bio provides reliable readings with low maintenance.
3 Metering of the gas consumption
of each engine
Measuring the consumption of natural
gas at the engine inlet provides the
necessary information for the computation of the individual engine efficiency
and optimization of the gas consumption. Accuracy of measurement and
system reliability is of utmost importance. The new FLOWSIC500 ultrasonic
compact gas meter from SICK enables
highly accurate metering in natural gas
distribution.
FLOWSIC600 Bio g p. 68
46
Power Industry | SICK
8015783/2013-05-08
Subject to change without notice
47. Focus 1
Fuel delivery / Storage
Diesel fired power plant
1 Gas flow at custody transfer
Measuring the consumption of natural gas at the gas connection point of
the plant gate provides the necessary
information for the computation of total
gas consumption for accounting with
the gas supplier. Accuracy of measurement and system reliability is of utmost
importance. The FLOWSIC600 Quatro
model combines two 4-path fiscal meters
with equal accuracy within one meter
body. The FLOWSIC600 Quatro detects
perturbations before they affect the
measuring results of the fiscal metering. The compact design with concealed
cabling provides a robust, trouble-free
and low-maintenance system. Due to the
direct path layout, the signals are not
reflected inside the device and thus not
influenced by contamination. This results
in long-term stability and accuracy of the
system.
3
FLOWSIC600 g p. 68
4 Tank inertization
In absence of mechanical moving parts,
the FLOWSIC500 is a robust, fail-safe
and low-maintenance device resulting in
a significant reduction in operating costs.
FLOWSIC500 can easily be integrated
into existing measuring stations or pipes.
The FLOWSIC500 operates either in an
energy self-sufficient configuration or
failsafe in network operation with battery
back-up.
FLOWSIC500 g p. 67
8015783/2013-05-08
Subject to change without notice
Surveillance of inert gas blanketing to
determine the oxygen content during
flow through inerting. Inert gas is fed into
the system from a gas inlet and simultaneously vented at another point when
loading or unloading liquid gas/other
flammable liquids. The TRANSIC100LP
is a laser oxygen transmitter suitable for
measuring O2 concentrations in inert
blanketing gas applications.
The TRANSIC100LP can operate at wide
temperatures both process and ambient,
suitable for installation in harsh industrial environments.
TRANSIC100LP g p. 56
Power Industry | SICK
47
48. Focus 2
DeNOx
Diesel fired power plant
2
1
2 Selective catalytic reactor (SCR) inlet prior to optimizing the SCR process
The selective catalytic reduction (SCR)
process is typically applied for NOx
reduction by adding a reagent such as
ammonia (NH3) which converts nitrogen
oxide into water and nitrogen over a catalyst at approx. 400 °C. NO concentration
is measured at the inlet as part of the
removal efficiency calculation. H2O and
O2 are measured for normalization and
to obtain a value of the water content
before the SCR to calculate the right balance with the value of the SCR outlet.
The MCS100E HW is often used for this.
The sample is kept hot during the entire
analysis using this multi-component
Infrared system. It can be set up to multiplex several sample points and measures up to 8 gas components including
H2O and O2.
MCS100E HW g p. 60
48
Power Industry | SICK
8015783/2013-05-08
Subject to change without notice
49. Focus 2
DeNOx
Diesel fired power plant
1 Recirculation air from turbo
charger to motor intake air
In order to reduce the NOx forming in
the motor itself, the oxygen content
in the cleaned recirculation stream
has to be measured and controlled.
The TRANSIC100LP provides real time
measurements for direct feedback and
control. The analyzer is easy to install
and to operate. Operational costs can
be kept to a minimum there are no
consumables and purging with nitrogen
is not necessary. Optics are heated to
prevent condensation and the measuring
values of this TDLS (tunable diode laser
spectroscopy) system are stable using an
internal drift monitoring system.
TRANSIC100LP g p. 56
3
3 Selective catalytic reactor (SCR) outlet prior to air heater
Environmental regulations demand
efficient reduction of the NOx content
of the flue gas before it is released into
the atmosphere. At the outlet of the
SCR, NOx and NH3 are measured: The
NH3 concentration (ammonia slip) is
important to limit the excess NH3 which
can foul and plug process components
downstream of the SCR, the NOx is used
to determine the efficency of the SCR.
The MCS100E HW is a good candidate
for this measurement especially for diesel
engine exhaust. The sample is kept hot
during the entire analysis using this multicomponent Infrared system. In addition,
it can be used for measuring several
sample points in sequence (both inlet and
outlet) and can measure up to 8 gas components including H2O and O2 used for
normalization of the measuring values.
MCS100E HW g p. 60
8015783/2013-05-08
Subject to change without notice
Power Industry | SICK
49
50. Focus 3
Dry flue gas desulfurization (FGD)
Diesel fired power plant
2
2 Filling dry sorbent from tanks for
transport to disposal site.
Sorbent used from the dry FGD is removed
from the collection hoppers and then transported by trucks to disposal sites. LMS511
position sensors are used to insure that the
loading spouts are correctly positioned and
no sorbent escapes into the atmosphere
at this transfer point. This powerful and
efficient laser scanner can measure up to
ranges of 80 m. Housed in a rugged IP 67
housing, it is immune to harsh weather
conditions and high dust environs associated with dry sorbent loading.
Bulkscan® LMS511 g p. 69
50
Power Industry | SICK
8015783/2013-05-08
Subject to change without notice
51. Diesel fired power plant
Focus 3
Dry flue gas desulfurization (FGD)
1 Sorbent material storage silo
Whether from the absorber or dust, the
collected particulate falls off into collecting hoppers. In order to detect if the
hopper is full, point level measurements
are made.The vibration limit switch
LBV300 is particularly outstanding for
its ruggedness. The LBV300 has no
mechanically moving parts and is insensitive to deposit formation. Apart from
that, it is characterized by easy installation as well as start-up without filling.
LBV310 g p. 70
1
8015783/2013-05-08
Subject to change without notice
Power Industry | SICK
51
52. Focus 4
Continuous emission monitoring
Diesel fired power plant
3
1
2
2 Monitoring dust emissions
Dust concentration or opacity is typically
measured in the stack emission in a
fossil fuel fired power plant. The exact
ranges of measurement and the number
of components are dependent on local
regulatory requirements and are indicated in the plant operating permit. The
DUSTHUNTER SP100 probe version is an
approved measuring device for very low
to medium dust concentrations.
An automatic check of zero and reference point and contamination check is
included. The DUSTHUNTER T200 cross
duct version is a measuring device for
dust at medium to high concentrations.
The principle of operation is optical
transmittance. The T200 includes a twosided contamination check as well as an
automatic self-alignment of the optical
assembly.
DUSTHUNTER T200 g p. 66
52
Power Industry | SICK
8015783/2013-05-08
Subject to change without notice
53. Diesel fired power plant
Focus 4
Continuous emission monitoring
1 Emission monitoring in exhaust gas
Bi- and trifuel fired diesel power plants
are often located in remote areas with
harsh environmental conditions where
maintenance and associated support
is difficult to get. Therefore, robustness
and long-term stability in CEMS measuring systems with calibration cells are
favored. SICK’s wide product portfolio
for emission monitoring provides flexible complete solutions here from one
source. Dust measuring devices from the
DUSTHUNTER product family are used,
in-situ gas analyzer and hot extractive
gas analyzers like MCS100E HW. The
FLOWSIC100 product family is available for measuring volume flow rates
and the MEAC computer system for
data aquisition and computation. Using
extractive or in-situ technology supports
optimum compliance with local measuring requirements.
MCS100E HW g p. 60
FLOWSIC100 g p. 66
3 Greenhouse gas control
The European directive 2003/87/EC for
trading greenhouse gas emission allowances requires proof of the CO2 emissions in many plants. Usually the CO2
amount is rather difficult to calculate,
therefore measurement in the exhaust
duct is a desirable alternative provided
the total uncertainty limits are met. SICK
has developed a solution for monitoring
the CO2 emissions directly and providing
the uncertainty certifications for reporting and trading of allowances on the
basis of the EU regulations. GHG Control
solution includes the GM35 NDIR gas
analyzer, the FLOWSIC100 ultrasonic
flow meter, MEAC GHG software package
plus engineering services to provide a
complete measurement system eliminating the need for laborious calculation
methods to save time and money.
GM35 g p. 57
FLOWSIC100 g p. 66
8015783/2013-05-08
Subject to change without notice
Power Industry | SICK
53
56. TRANSIC100LP | Gas transmitters
GM32 | In-situ gas analyzers
A
B
C
D
E
F
H
I
J
K
L
M
N
O
P
Q
R
S
T
TRANSIC100LP – At a glance
•• O2 transmitter using effective laser
spectroscopy (TDLS)
•• For use in potentially explosive
atmospheres (FM, ATEX and IECEx
certificate)
•• In-situ-measurement directly in the
process or extractive using a sample
cell (option)
•• Optimized for use in harsh industriel
environments
•• Transmitter concept – compact
design and simple to operate
•• Long term stability
•• No moving part
Your benefits
•• Fast real-time measurements, right in
the process
•• Easy to install, easy to operate
•• Diagnostic output for preventive
maintenance
•• Minimizes the need for sample conditioning equipment
•• Low operational costs: no consum-
ables and no purge gas consumption
•• Robust - measures reliably in unpurified gases
-- www.mysick.com/en/TRANSIC100LP
For more information, just enter the link or scan the QR code and get direct access to technical
data, CAD design models, operating instructions, software, application examples and much more.
GM32 – At a glance
•• Direct, fast in-situ measurement
•• No gas sampling, no gas transport,
no gas conditioning
•• Up to eight measuring components at
the same time, plus process temperature and pressure
•• DOAS and CDE evaluation process
•• Numerous independent measuring
ranges with consistent accuracy
•• Automatic self-test function (QAL3)
without test gases
•• Overpressure encapsulated design for
ATEX Zones 1 and 2
Your benefits
•• Measured values in real time without
altering the gas composition
•• Short-term process deviations are
detected
•• Representative measurement byselection of cross-duct or measuring
probe versions
•• Fast on-site service due to modular
design
•• Long maintenance-free intervals
•• Cost-effective in-situ gas analyzer –
also in ATEX design
•• Low cost of installation and operation, no test gases required
•• Complete emissions measurement in
Kraft pulp process by way of simultaneous measurement of TRS components plus SO2, NO, NH3
-- www.mysick.com/en/GM32
For more information, just enter the link or scan the QR code and get direct access to technical
data, CAD design models, operating instructions, software, application examples and much more.
56
Power Industry | SICK
8015783/2013-05-08
Subject to change without notice
57. In-situ gas analyzers | GM35
In-situ gas analyzers | GM700
GM35 – At a glance
•• Dynamic humidity correction
•• Fast in-situ measurement directly in
•• No gas sampling and conditioning
•• Gas testable version of measuring
•• Simultaneous determination of up to
•• Integrated self test and control
the process
three gas components, temperature
and pressure
probe available
functions
Your benefits
•• Dynamic humidity measurement
directly in the process
•• Provision of real humidity reference
values
•• Unbiased measuring values due to
in-situ measurement
•• Fast or short-term fluctuations in the
process are being detected
•• Representative measurement by
selection of an appropriate probe or
cross-duct type
-- www.mysick.com/en/GM35
For more information, just enter the link or scan the QR code and get direct access to technical
data, CAD design models, operating instructions, software, application examples and much more.
GM700 – At a glance
•• High selectivity due to high spectral
resolution
•• Short response times
•• No calibration required
•• No moving parts: minimal wear and
tear
•• No gas sampling and conditioning
required
Your benefits
•• Unbiased measuring values due to
in-situ measurement directly in the
process
•• Best application solution using probe
or cross-duct type
•• High reliability during operation
•• Also applicable for harsh environment
conditions
•• Detection of fast and short-term
process fluctuations
-- www.mysick.com/en/GM700
For more information, just enter the link or scan the QR code and get direct access to technical
data, CAD design models, operating instructions, software, application examples and much more.
8015783/2013-05-08
Subject to change without notice
Power Industry | SICK
57
A
B
C
D
E
F
H
I
J
K
L
M
N
O
P
Q
R
S
T
58. GM901 | In-situ gas analyzers
ZIRKOR302 | In-situ gas analyzers
A
B
C
D
E
F
H
I
J
K
L
M
N
O
P
Q
R
S
T
GM901 – At a glance
•• Representative measurement across
the duct
•• Operation via evaluation unit
•• Short response times
•• Verifiable with gas-filled cuvette;
gas testable probe with test gas
Your benefits
•• Measurement results in real time due
to in-situ measurement
•• Fast and simple installation and commissioning
•• Easy, user-friendly operation
•• Economical due to low maintenance
-- www.mysick.com/en/GM901
For more information, just enter the link or scan the QR code and get direct access to technical
data, CAD design models, operating instructions, software, application examples and much more.
ZIRKOR302 – At a glance
•• All parts in contact with gas are
heated
•• Automatic testing and adjustment
with ambient air
•• Fixed physical zero point
•• Short response time
•• Operation of up to 3 sensors via one
evaluation unit
Your benefits
•• For high process temperatures up to
1400 °C
•• No reference gas required
•• No re-ignition into sample gas
possible
•• Ideal for process control due to rapid
measurement
•• Economic due to low maintenance
effort
-- www.mysick.com/en/ZIRKOR302
For more information, just enter the link or scan the QR code and get direct access to technical
data, CAD design models, operating instructions, software, application examples and much more.
58
Power Industry | SICK
8015783/2013-05-08
Subject to change without notice
59. Extractive gas analyzers | SIDOR
Extractive gas analyzers | MCS300P
SIDOR – At a glance
•• Detector with high long-term stability
•• Paramagnetic or electrochemical O2
measurement
•• Automatic adjustment with
component-free ambient air
•• Insensitive to contaminations
Your benefits
•• Automatic adjustment, self-monitoring and fault diagnosis
•• Test gas adjustment only every 6
months
•• Long maintenance intervals
•• TÜV approval and ATEX type approval
for measurement of CH4, CO2 and O2
•• Repairable on site
•• Exchange of components without
complicated temperature adjustment
in the factory
-- www.mysick.com/en/SIDOR
For more information, just enter the link or scan the QR code and get direct access to technical
data, CAD design models, operating instructions, software, application examples and much more.
MCS300P – At a glance
•• Simultaneous measurement of up to
6 components
•• Process cuvettes up to 60 bar and
200 °C
•• Automatic sample point switching
•• Integrated adjustment unit
•• Safety devices for measurement of
toxic or flammable mixtures
•• Extended operation via PC and
software SOPAS ET
•• Flexible I/O module system
Your benefits
•• Automatic adjustment without
expensive test gases
•• Integration in existing networks
•• Integration of external parameters
like temperature or pressure
•• Suitable for potentially explosive
atmospheres
-- www.mysick.com/en/MCS300P
For more information, just enter the link or scan the QR code and get direct access to technical
data, CAD design models, operating instructions, software, application examples and much more.
8015783/2013-05-08
Subject to change without notice
Power Industry | SICK
59
A
B
C
D
E
F
H
I
J
K
L
M
N
O
P
Q
R
S
T
60. MERCEM300Z | Extractive gas analyzers
MCS100E HW | CEMS solutions
A
B
C
D
E
F
H
I
J
K
L
M
N
O
P
Q
R
S
T
MERCEM300Z – At a glance
•• Accurate measurement of “total
mercury” directly in a thermal
converter (patented)
•• Measuring operation without using
consumables
•• Very low maintenance gas sampling
using an ejector pump – no moving
parts
•• Integrated adjustment cell for
automatic drift correction
•• Automatic adjustment of the entire
measuring system with a built-in test
gas generator (optional)
•• Modular design with the entire
system
Your benefits
•• Reliable results of the actual measuring values of elemental Hg and Hg
compounds in gases
•• Very low operating expenses
•• Minimum maintenance expenditure
•• Long-term stability minimizes technician time requirements due to selfadjusting measuring system
•• Measuring certainty using the fully
automated adjustment with test gas
•• Convenient and fast access for easy
service and user-friendly remote
diagnosis
-- www.mysick.com/en/MERCEM300Z
For more information, just enter the link or scan the QR code and get direct access to technical
data, CAD design models, operating instructions, software, application examples and much more.
MCS100E HW – At a glance
•• Extractive measurement of up to 8
IR-active gas compounds
•• Additional oxygen and total hydro
carbon analyzers as an option
•• Gas paths completely heated
•• Test gas supply at the gas sampling
probe or at the analyzer
•• Back-purging of gas sampling probe
for cleaning of filters
•• Fast sample gas exchange for
minimizing adsorption and desorption
effects
•• Automated sample point switching
Your benefits
•• Measurement of several gas components with one analyzer
•• Heated gas paths enables measurement of difficult gases like HCl and
NH3
•• Long maintenance intervals (typically
3 months) due to self monitoring of
the analyzer
•• QAL3 drift test according to
EN 14181 with internal calibration
filter wheel – no test gas required
-- www.mysick.com/en/MCS100E_HW
For more information, just enter the link or scan the QR code and get direct access to technical
data, CAD design models, operating instructions, software, application examples and much more.
60
Power Industry | SICK
8015783/2013-05-08
Subject to change without notice
61. CEMS solutions | PowerCEMS
CEMS solutions | MEAC
PowerCEMS – At a glance
•• Completely configured system with
sampling, gas cooler, and integrated
sample gas pump
•• Modular design makes assemblies
easily accessible
•• Control unit for measured value and
status indication
•• Analyzer module with 24 V power
supply for quick on-site exchange
•• Certified as a fully configurable emis-
sion monitoring system in compliance
with EN15267
Your benefits
•• Simple integration of external sen-
sors such as pressure, temperature,
volume flow, and dust
•• High availability
•• Easy and quick exchange of modules
and sensors
•• Simple installation and quick commissioning
•• Cost-effective solution for simultaneous NO/NO2 measurement, since no
NOx converter is required
•• Remote access via Ethernet or
Modbus connection
•• Compact system design requires
minimal space
-- www.mysick.com/en/PowerCEMS
For more information, just enter the link or scan the QR code and get direct access to technical
data, CAD design models, operating instructions, software, application examples and much more.
MEAC – At a glance
•• Evaluation according to EU directives
2000/76/EC and 2001/80/EC
•• Evaluation according to 13., 17., 27.
and 30. FICA and TA -Luft (Technical.
Instructions on Air Quality Control)
•• Inclusion of operational parameters
and plant conditions
•• Visualization of emission and
operational data
•• Remote data transfer, remote
diagnosis and remote control
•• Alarm signals when exceeding the
limit values
Your benefits
•• Software monitors all communica-
tions with connected field devices
and control systems
•• All values are stored on hard disk,
thus it is possible to look at data history even after many years
•• A routine back-up is made regularly
on a second hard disk
•• Screen displays and output of actual
and historical data are freely configurable
-- www.mysick.com/en/MEAC
For more information, just enter the link or scan the QR code and get direct access to technical
data, CAD design models, operating instructions, software, application examples and much more.
8015783/2013-05-08
Subject to change without notice
Power Industry | SICK
61
A
B
C
D
E
F
H
I
J
K
L
M
N
O
P
Q
R
S
T
62. MKAS Compact | Customized analyzer systems
MAC800 | Customized analyzer systems
A
B
C
D
E
F
H
I
J
K
L
M
N
O
P
Q
R
S
T
MKAS Compact – At a glance
•• Compact analyzer cabinet
•• For maximum 2 S710 or SIDOR
analyzers or NOx converter
•• Includes the major system components
•• Wired and tested – ready for use
Your benefits
•• Space-saving complete system
•• Adaptable to the measuring task due
to modular concept
•• Proven system components offer a
reliable solution
•• Fulfills the requirements for an auto-
matic measuring system according to
EU standards, especially EN 15267-3
-- www.mysick.com/en/MKAS_Compact
For more information, just enter the link or scan the QR code and get direct access to technical
data, CAD design models, operating instructions, software, application examples and much more.
MAC800 – At a glance
•• Cold-extractive analyzer system certified according to EN 15267-3
•• Plug-and-play analyzer modules with
24 V power supply
•• Operating unit for displaying all measured values and status information
on a touch screen
•• External sensors via interfaces
connectable
•• Display and control of external
sensors is possible
•• Remote control of the complete
system via Ethernet, Modbus or additional GPRS modem
Your benefits
•• Cost-effective investment because of
easy modifications for future needs
•• Easy commissioning and troublefree on-site approval of the automatic measuring system (AMS) by the
relevant authorities
•• Full overview via touchscreen and
integration of remote sensors (p, T,
volume flow, dust)
•• Easy service due to clear separation
of the electrical and the analytical
sections
•• High availability through easy and fast
change of modules
•• Ethernet or Modbus connection to
networks
-- www.mysick.com/en/MAC800
For more information, just enter the link or scan the QR code and get direct access to technical
data, CAD design models, operating instructions, software, application examples and much more.
62
Power Industry | SICK
8015783/2013-05-08
Subject to change without notice
63. Process solutions | GM960
Scattered light dust measuring devices | FWE200
GM960 – At a glance
•• Up to 40 boiler wall probes, each with
one CO and O2 sensor for installation
directly in the boiler wall
•• Up to 40 connection units for pressurized air, power supply and data bus
•• One master unit with standard
network connection for operating the
peripheral system components
•• Software MEPA-GM960 for graphical
visualization of readings, for process
control, storage of data and communication
Your benefits
•• Online monitoring of values relevant
to corrosion for the optimization of
combustion control
•• Effects of adjustment of the burners
and combustion air can be followed
online
•• Lowering of operational costs and potentially improved safety through early
warning of potential dangers caused
by corrosive erosion of the boiler wall
•• Efficient location of possible problem
areas of the boiler wall
•• Use of data for creation of effective
maintenance and revision plans
•• Installation and commissioning possible while boiler running
-- www.mysick.com/en/GM960
For more information, just enter the link or scan the QR code and get direct access to technical
data, CAD design models, operating instructions, software, application examples and much more.
FWE200 – At a glance
•• For very low to medium dust concen-
trations
•• Gas sampling and return combined in
one probe
•• Contamination check
•• Automatic check of zero and reference point
Your benefits
•• Reliable dust measurement in wet
gas
•• No movable parts with contact to aggressive gas, therefore low maintenance efforts
•• Installation directly at the duct due to
compact design
-- www.mysick.com/en/FWE200
For more information, just enter the link or scan the QR code and get direct access to technical
data, CAD design models, operating instructions, software, application examples and much more.
8015783/2013-05-08
Subject to change without notice
Power Industry | SICK
63
A
B
C
D
E
F
H
I
J
K
L
M
N
O
P
Q
R
S
T
64. DUSTHUNTER SB50 | Scattered light dust measuring devices
DUSTHUNTER SP100 | Customized analyzer systems
A
B
C
D
E
F
H
I
J
K
L
M
N
O
P
Q
R
S
T
DUSTHUNTER SB50 – At a glance
•• For low to medium dust
concentrations
•• One-side installation
•• Automatic check of zero and
reference point
•• Automatic compensation of back-
ground radiation, therefore no light
absorber necessary
•• For medium to large duct diameters
Your benefits
•• Easy installation, commissioning and
operation
•• Measurement independent of gas
velocity, humidity and particle charge
•• Low maintenance due to
self-monitoring
-- www.mysick.com/en/DUSTHUNTER_SB50
For more information, just enter the link or scan the QR code and get direct access to technical
data, CAD design models, operating instructions, software, application examples and much more.
DUSTHUNTER SP100 – At a glance
•• One-side installation
•• For very low to medium dust concen-
•• Contamination check
•• Hastelloy probe available for corrosive
•• Automatic check of zero and refer-
•• For small to medium duct diameters
trations
ence point
gas environments
Your benefits
•• Ideal for thick- or double-walled ducts
•• Approved according to EN 15267-3
•• Low maintenance due to self-monitoring and contamination check
-- www.mysick.com/en/DUSTHUNTER_SP100
For more information, just enter the link or scan the QR code and get direct access to technical
data, CAD design models, operating instructions, software, application examples and much more.
64
Power Industry | SICK
8015783/2013-05-08
Subject to change without notice
65. Transmittance dust measuring devices | DUSTHUNTER T50
Transmittance dust measuring devices | DUSTHUNTER T100
A
B
C
D
E
F
DUSTHUNTER T50 – At a glance
•• For medium to high dust
concentrations
•• For small to medium measuring
distances
•• Automatic check of zero and
reference point
Your benefits
•• Easy installation, commissioning and
operation
•• Measurement independent of gas
velocity, humidity and particle charge
•• Low maintenance due to
self-monitoring
-- www.mysick.com/en/DUSTHUNTER_T50
For more information, just enter the link or scan the QR code and get direct access to technical
data, CAD design models, operating instructions, software, application examples and much more.
DUSTHUNTER T100 – At a glance
•• For medium to high dust
concentrations
•• Integrated contamination check
•• Automatic check of zero and
reference point
•• For small to large measuring
distances
Your benefits
•• Easy installation, commissioning and
operation
•• Measurement independent of gas
velocity, humidity and particle charge
•• Low maintenance due to
self-monitoring
•• Approved according to EN 15267-3
-- www.mysick.com/en/DUSTHUNTER_T100
For more information, just enter the link or scan the QR code and get direct access to technical
data, CAD design models, operating instructions, software, application examples and much more.
8015783/2013-05-08
Subject to change without notice
Power Industry | SICK
65
H
I
J
K
L
M
N
O
P
Q
R
S
T
66. DUSTHUNTER T200 | Scattered light dust measuring devices
FLOWSIC100 M/H/PR/S | Volume flow measuring devices
A
B
C
D
E
F
H
I
J
K
L
M
N
O
P
Q
R
S
T
DUSTHUNTER T200 – At a glance
•• Integrated contamination check for
sender/receiver and reflector unit
•• Automatic self-alignment of the
optical assembly
•• Automatic check of zero and reference point
•• For medium to high dust concentrations
•• For small to large measuring
distances
Your benefits
•• Easy installation, commissioning and
operation
•• Measurement independent of gas
velocity, humidity and particle charge
•• Low maintenance due to self-monitoring and contamination check
•• Approved according to EN 15267-3
-- www.mysick.com/en/DUSTHUNTER_T200
For more information, just enter the link or scan the QR code and get direct access to technical
data, CAD design models, operating instructions, software, application examples and much more.
FLOWSIC100 M/H/PR/S – At a glance
•• Rugged titanium transducers for high
durability
•• Measuring system without purge air
•• Corrosion-resistant material for application in aggressive gases (option)
•• Integral measurement over the duct
diameter with types H, M and S
•• Probe type PR for economic installation from one side of the duct
•• Automatic function control with zero
and span point check
Your benefits
•• Reliable flow measurement for ducts
with small up to very large diameters
•• High durability of the device
•• Very low operating and maintenance
costs due to operation without purge
air
•• Accurate measuring results under
difficult measuring conditions
•• Measurement without pressure
loss, therefore no influences on the
process
•• User-friendly operation via SOPAS ET
software
•• Reliable function monitoring due to
enhanced diagnosis
-- www.mysick.com/en/FLOWSIC100_M_H_PR_S
For more information, just enter the link or scan the QR code and get direct access to technical
data, CAD design models, operating instructions, software, application examples and much more.
66
Power Industry | SICK
8015783/2013-05-08
Subject to change without notice
67. Volume flow measuring devices | FLOWSIC100 M-AC/H-AC
Ultrasonic gas flow meter | FLOWSIC500
FLOWSIC100 M-AC/H-AC – At a glance
•• Rugged titanium transducers for high
•• Corrosion-resistant material for appli-
•• Innovative internal cooling for applica-
•• Integral measurement over the duct
durability
tions with gas temperatures up to
450 °C
•• No input of cooling air into measuring
medium
cation in aggressive gases (option)
diameter
•• Automatic function control with zero
and span point check
Your benefits
•• Reliable flow measurement for ducts
with small up to large diameters
•• High durability of the device
•• Minimum operating and maintenance
costs
•• No influence on measuring medium
due to closed cooling circuit
•• Accurate measuring results under
difficult measuring conditions
•• Measurement without pressure
loss, therefore no influences on the
process
•• User-friendly operation via SOPAS ET
software
•• Reliable function monitoring due to
enhanced diagnosis
-- www.mysick.com/en/FLOWSIC100_M-AC_H-AC
For more information, just enter the link or scan the QR code and get direct access to technical
data, CAD design models, operating instructions, software, application examples and much more.
FLOWSIC500 – At a glance
•• Cutting-edge technology: ultrasound
•• Diagnostics and permanent operational check
•• Robust and reliable without moving
parts
•• Replacable cartridge
•• Straight inlet/outlet piping not
required
•• Overload-proof
•• Optional integrated volume
correction/data registration
•• Battery or intrinsically safe power
supply
Your benefits
•• Ultimate measurement certainty and
safety of continuous gas supply
•• Reduction of installation costs due to
integrated volume correction
•• Simple installation, compatible with
conventional technologies (turbine
and rotary displacement meters)
•• Minimal operating costs as nearly
maintenance-free
•• Simplified recalibration due to
straightforward cartridge replacement
•• Reliable under dynamic load changes
•• Self-sufficient operation
®
C
US
-- www.mysick.com/en/FLOWSIC500
For more information, just enter the link or scan the QR code and get direct access to technical
data, CAD design models, operating instructions, software, application examples and much more.
8015783/2013-05-08
Subject to change without notice
Power Industry | SICK
67
A
B
C
D
E
F
H
I
J
K
L
M
N
O
P
Q
R
S
T
68. FLOWSIC600 | Ultrasonic gas flow meter
FLOWSIC600 Bio | Volume flow measuring devices
A
B
C
D
E
F
H
I
J
K
L
M
N
O
P
Q
R
S
T
FLOWSIC600 – At a glance
•• High efficient transducers
•• Direct path layout
•• Intelligent self-diagnosis
•• Compact and robust design
•• Integrated logbook and data logs
•• Wide measuring range up to 1:120
•• Bidirectional measurement
•• Low power consumption (1 W)
Your benefits
•• Low maintenance effort due to intel-
ligent self-diagnosis
•• No pressure loss
•• Nearly insensitive to pressure regulator noise
•• Calibration with air at atmospheric
pressure possible
•• Transducer can be dismantled under
line pressure
•• Power supply via solar panel possible
-- www.mysick.com/en/FLOWSIC600
For more information, just enter the link or scan the QR code and get direct access to technical
data, CAD design models, operating instructions, software, application examples and much more.
FLOWSIC600 Bio – At a glance
•• Flow measurement for biogas plants
•• Durable, reliable, low maintenance
•• Lightweight meter body made from
•• Process measurement with an uncer-
•• Non-corrosive materials, anti-stick
•• Installation in PE and stainless steel
polyethylen (PE100)
surface
•• Measurement in wet and corrosive
tainty of ± 1.5%
•• Version for ATEX-zone 1 and -zone 2
available
piping possible
gases
Your benefits
•• The advantages of ultrasonic gas flow
measurement adapted to the special
application conditions of biogas
plants
•• Measuring devices based on ultra-
sound technology can be applied in
all process stages between fermentation and injection into natural gas
grids
•• Low maintenance costs
•• No pressure drop
-- www.mysick.com/en/FLOWSIC600_Bio
For more information, just enter the link or scan the QR code and get direct access to technical
data, CAD design models, operating instructions, software, application examples and much more.
68
Power Industry | SICK
8015783/2013-05-08
Subject to change without notice
69. 2D laser scanners | LMS5xx
Flow sensors | Bulkscan® LMS511
LMS5xx – At a glance
•• Powerful and efficient laser measure-
ment sensor for ranges of up to 80 m
•• Outstanding performance in adverse
environmental conditions due to
multi-echo technology
•• IP 67 enclosure rating, built-in heater,
highly compact design
•• Low power consumption
•• Fast signal processing
•• Multiple I/Os
•• Synchronization of multiple sensors
possible
Your benefits
•• Superior performance in a vast range
of applications
•• Smallest sensor with highest accuracy in its class
•• Comprehensive range of lines and
models to suit all performance and
price requirements
•• Fast, reliable object detection in
nearly any weather conditions
•• Low power consumption reduces total
cost of ownership
•• Best price/performance ratio in this
sensor class on the market
•• Fast, easy commissioning due to
SOPAS software
•• Self-monitoring functions increase
system availability
-- www.mysick.com/en/LMS5xx
For more information, just enter the link or scan the QR code and get direct access to technical
data, CAD design models, operating instructions, software, application examples and much more.
Bulkscan® LMS511 – At a glance
•• Non-contact measurement of volume
and mass flow of bulk material
•• Laser pulses with high angular
resolution ensure outstanding image
resolution
•• 5-echo pulse evaluation produces
highly reliable measurements
•• Offers non-contact belt monitoring
•• Integrated center-of-gravity calculator
•• Robust structure for harsh ambient
conditions
•• Can also measure at low temperatures thanks to integrated heater
•• Compact housing with enclosure rating IP67
Your benefits
•• Maximizes conveyor throughput
•• Reduces maintenance costs by
preventing belt slippage
•• Increases the conveyor belt’s service
life
•• Reduces loading time
•• Increases efficiency by optimizing belt
capacity
•• Simple installation
•• Low maintenance costs
•• Offers savings through minimized
energy consumption
-- www.mysick.com/en/Bulkscan_LMS511
For more information, just enter the link or scan the QR code and get direct access to technical
data, CAD design models, operating instructions, software, application examples and much more.
8015783/2013-05-08
Subject to change without notice
Power Industry | SICK
69
A
B
C
D
E
F
H
I
J
K
L
M
N
O
P
Q
R
S
T
70. LBV310 | Level sensors
LBV330 | Level sensors
A
B
C
D
E
F
H
I
J
K
L
M
N
O
P
Q
R
S
T
LBV310 – At a glance
•• Rugged device design
•• Several housing materials and electri-
•• Very high repeatability
•• ATEX versions (1D/2D/1G/2G) avail-
•• Immune to deposit formation
•• Commissioning without filling
•• Process temperature up to 250 °C
•• Tube extensions (LBV330) and rope
cal outputs available
able
extensions (LBV320) available for vertical mounting up to 80 m distance
Your benefits
•• Easy installation and commissioning,
no calibration necessary
•• Easy operation and integration, saves
time
•• Maintenance-free sensor, reduces
downtime
•• Testing in place possible – no mount-
ing required, which reduces installation time
•• Flexible and tough system for a multitude of applications
-- www.mysick.com/en/LBV310
For more information, just enter the link or scan the QR code and get direct access to technical
data, CAD design models, operating instructions, software, application examples and much more.
LBV330 – At a glance
•• Rugged device design with tube
extension up to 6 m
•• Several housing materials and electrical outputs available
•• Immune to deposit formation
•• Commissioning without filling
•• Process temperature up to 250 °C
•• Very high repeatability
•• ATEX versions (1D/2D/1G/2G) available
•• Short versions (LBV310) and rope-
extended devices (LBV330) available
Your benefits
•• Easy installation and commissioning,
no calibration necessary
•• Easy operation and integration, saves
time
•• Maintenance-free sensor, reduces
downtime
•• Testing in place possible – no mount-
ing required, which reduces installation time
•• Flexible and robust system for a multitude of applications
•• Solutions for vertically mounted sensors in difficult installation conditions
-- www.mysick.com/en/LBV330
For more information, just enter the link or scan the QR code and get direct access to technical
data, CAD design models, operating instructions, software, application examples and much more.
70
Power Industry | SICK
8015783/2013-05-08
Subject to change without notice
71. Level sensors | LBV310
Level sensors | LBV330
A
B
C
D
E
F
8015783/2013-05-08
Subject to change without notice
Power Industry | SICK
71
H
I
J
K
L
M
N
O
P
Q
R
S
T
72. Company
Sensor Intelligence is a promise
At SICK, sensor solutions are developed for industrial automation with commitment
and experience. From development to service provision: Every employee is completely
committed to ensuring that sensors and application solutions from SICK optimally
fulfill their versatile functions.
Company with a culture of success
With a variety of products and services, approximately
5,800 employees help SICK sensor technology users to
increase their productivity and reduce their costs. Founded in
1946, the company has its headquarters in Waldkirch,
Germany, and with nearly 50 subsidiaries and interests,
in addition to numerous representatives, it is globally active.
72
Power Industry | SICK
People like working at SICK. This is evident from the fact
that SICK has regularly been named Employer of the Year.
This lively workplace culture has a strong appeal for qualified
and skilled persons. At SICK, they are part of a company that
offers a balance between career progression and quality of life.
8015783/2013-05-08
Subject to change without notice
73. Company
A
B
Innovation creates competitive advantage
Model with a far-reaching effect
SICK sensors simplify procedures and optimize processes to
achieve sustainable production. To do this, SICK has researched
and developed facilities in many locations across the globe.
In discussion with its customers and in cooperation with higher
education institutions, innovative sensor products and solutions
are developed. These form the basis for reliable process control,
personal protection and environmentally friendly production.
SICK builds upon an established corporate culture, pursuing
financial independence and technological transparency. Innovation has made SICK into a technological and market leader.
Because it is only with targeted modernization and improvement
that universally applicable sensors can be successful in the
long term.
C
D
E
F
G
H
I
J
8015783/2013-05-08
Subject to change without notice
Power Industry | SICK
73
K
74. Industries
A
Sensor Intelligence for all requirements
B
SICK has representation in numerous fields and is therefore familiar with the processes used in a wide range of industries. Fundamental requirements such as
precision, speed and availability apply globally, but must be implemented differently
according to the industry in question.
C
For applications all over the world
D
Hundreds of thousands of installations and implemented applications prove it: SICK is familiar with the industries and their
processes. And that is not going to change – in the application
centers in Europe, Asia and North America, sensors and system
solutions are designed, tested and optimized in accordance
with customer specifications. This contributes to the company's
position as a reliable supplier and development partner.
E
F
G
H
I
J
K
74
Power Industry | SICK
8015783/2013-05-08
Subject to change without notice
75. Industries
A
For industries with specific dynamics
For better results in all fields
Where the demands for quality and productivity rise in parallel,
industries profit from SICK's profound knowledge and expertise
in the relevant sectors. In addition to the automotive and pharmaceutical industries, this also applies to the electronics and
solar sectors. SICK provides productive solutions for accident
prevention in automated guided vehicles and increases the
throughput speed and traceability in warehouses and distribution centers. For protection of the environment and process
optimization in cement production, waste incineration or in
power stations, SICK provides system solutions for gas analysis
and flow measurement. Natural gas distribution networks use
the high-precision gas meters manufactured by SICK.
Every field has special procedures. And yet the tasks of the
sensors is identical in principle: To measure, detect, control
and monitor, protect, connect and integrate, identify, position.
This puts the SICK specialists in the position to provide successful solutions industry-wide for other industrial automation
applications.
www.sick.com/industries
B
C
D
E
F
G
H
I
J
8015783/2013-05-08
Subject to change without notice
Power Industry | SICK
75
K
76. SICK LifeTime Services
A
B
C
D
For safety and productivity:
SICK LifeTime Services
From system planning to upgrade services, SICK LifeTime Services
provide a high quality of service all over the world. These services
enhance personal safety and increase machine productivity to produce
a solid foundation for sustainable operation.
Benefit from SICK services
Personal safety and machine and system productivity are largely
dependent on the availability of the services required in each
phase of a product's life cycle, i.e. the services that enable and
sustain the functional integrity and reliability of a sensor, system
or safety device. At SICK, this is possible thanks to comprehensive industry know-how and more than 60 years of practical
experience!
E
F
G
H
I
J
K
76
Power Industry | SICK
8015783/2013-05-08
Subject to change without notice
77. SICK LifeTime Services
Consulting Design
••
••
••
••
••
Plant walk-through
Risk assessment
Safety concept
Feasibility studies
Software and hardware
design
Product System
Support
••
••
••
••
Commissioning
Exchange units and spare parts
Remote support
Hotline
Verification
Optimization
••
••
••
••
••
••
Inspections
Maintenance
Barcode testing
Accident investigation
Stoptime measurement
Machine safety inspection
Training Education
A
•• User training
•• Seminars
•• WebTraining
B
Upgrade Retrofits
C
•• Machine retrofitting
•• Sensor upgrades
•• Technology retrofitting
www.sick.com/service
D
E
F
G
H
I
J
8015783/2013-05-08
Subject to change without notice
Power Industry | SICK
77
K
78. Product overview
Versatile product range for industrial automation
From the simple acquisition task to the key sensor technology in
a complex production process: With every product from its broad
portfolio, SICK offers a sensor solution that best combines cost effectiveness and safety.
www.sick.com/products
Photoelectric sensors
•• Miniature photoelectric sensors
•• Small photoelectric sensors
•• Compact photoelectric sensors
•• Fiber-optic sensors and fibers
•• Cylindrical photoelectric sensors
•• MultiTask photoelectric sensors
•• Inductive proximity sensors
•• Capacitive proximity sensors
•• Magnetic proximity sensors
•• Analog positioning sensors
•• Sensors for T-slot cylinders
•• Sensors for C-slot cylinders
•• Sensor adapters for other
cylinder types
•• Bar code scanners
•• Image-based code readers
•• Hand-held scanners
•• RFID
Proximity sensors
Magnetic cylinder sensors
Identification solutions
78
Power Industry | SICK
8015783/2013-05-08
Subject to change without notice
79. Product overview
Detection and ranging solutions
•• Laser measurement technology
System solutions
•• Volume measurement systems
•• Code reading systems
•• Dimension weighing scanning
systems
•• Vision systems
•• Level sensors
•• Pressure sensors
•• Flow sensors
•• Temperature sensors
••
••
••
••
•• Array sensors
•• Register sensors
•• Markless sensors
Fluid sensors
Registration sensors
Contrast sensors
Color sensors
Luminescence sensors
Fork sensors
Distance sensors
•• Short range distance sensors
(displacement)
•• Mid range distance sensors
•• Long range distance sensors
•• Linear measurement sensors
8015783/2013-05-08
Subject to change without notice
••
••
••
••
Ultrasonic sensors
Double sheet detector
Optical data transmission
Position finders
Power Industry | SICK
79
81. Product overview
Motor feedback systems
•• Interfaces: incremental, HIPERFACE® and HIPERFACE DSL®
•• Safety motor feedback systems
•• Rotary and linear motor feedback systems for asynchronous,
synchronous motors and linear
motors
•• Absolute encoders
•• Incremental encoders
•• Linear encoders
•• Wire draw encoders
•• Gas analyzers
•• Dust measuring devices
•• Analyzer systems
•• Liquid analyzers
•• Data acquisition systems
•• Tunnel sensors
•• Gas flow meters
•• Mass flow meters
•• Volume flow measuring devices
Encoders
Analyzers and systems
Gas flow measuring devices
Software
•• Safexpert® safety software
8015783/2013-05-08
Subject to change without notice
Power Industry | SICK
81